Harbor Freight Tools 100 Ft. Open Side Steel Air Hose Reel Product manual
Contents
1. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference CENTRALPNEUMATIC air hose reel Visit our website at http www harborfreight com ITEM 46342 REV 14i Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 888 866 5797 as soon as possible Copyright 2001 by Harbor Freight Tools All rights reserved i A r No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Hose Capacity 50 of 1 2 Hose or 100 of 3 8 Hose Air Inlet 1 4 18 NPT 90 Swivel Female Air Outlet 1 4 18 NPT Female Weight 9 25 L2. Tighten if necessary 4 The axle air valve fitting that rotates in the base may occasionally need light grease to insure smooth operation Do not get grease on the air hose Item 46342 For technical questions please call 1 888 866 5797 Page 5 Parts List o fwe e Cee o O P14 Reet SSCS SC 18 Swivel Valve including two valves and 1 two O rings ane a Swee Se Ca e fe PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Page 6 For technical questions please call 1 888 866 5797 Item 46342 Assembly Drawing Item 46342 For technical questions please call 1 888 866 5797 Page 7 Limited 90 D
3. ay Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but i
4. bs Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this product 1 Avoid working alone If an accident happens an assistant can bring help 2 Keep work area clean Cluttered areas invite injuries 3 Observe work area conditions Don t expose to rain Keep work area well lighted 4 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords or air hoses 5 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 6 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair 7 Use eye and ear protection Always wear ANSI approved impact safety goggles 8 Do not overreach Keep proper footing a
5. e opening and closing during rotation If you are not receiving enough air rotate the reel 1 4 turn Note Make sure the Swivel Valve 18 is secure Tighten it with a wrench if necessary 8 Attach your tool of choice to the end of the extension hose and after reading the tool manual turn on your compressor and begin working 9 When finished turn the Handle 3 clockwise and coil the hose onto the Hose Reel making sure it covers the reel evenly Caution Always be alert to pressure inside hose when rolling hose on or off the reel protect eyes and face from pressurized hose movement Page 4 For technical questions please call 1 888 866 5797 Item 46342 Operation 14 NPS Ait Hose Line Valve Giler T Filer I AIR ee COMPRESSOR eres Air Hose on Reel Regutator Recommended Air Line Components For best service you should incorporate an oiler a regulator and an inline filter as shown in the diagram above Hoses couplers fittings oilers regulator and filters are all available from Harbor Freight Tools Maintenance 1 Before each use check fittings for leaks If found remove fittings and re apply new PTFE tape 2 Periodically clean the Hose Reel by wiping down with a cloth moistened with warm water and mild detergent Do not use harsh cleaners or solvents as they may damage Hose Reel air hose seals or paint 3 Periodically check that the Hose Reel is firmly attached to the wall
6. f we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state CENTRALPNEUMATIC 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
7. l if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Use proper size and type extension cord If an extension cord is required it must be of the proper size and type to supply the correct current to the air compressor without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool Check your air compressor s manual for the proper size cord Maintenance For your safety maintenance should be performed regularly by a qualified technician Air Compressor Before using the Hose Reel read and follow the instructions in your air compressor manual WARNING The brass components of this product contain lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq WARNING This product contains di 2 ethylhexyl phthalate DEHP a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code 25249 5 et seq The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into
8. nd balance at all times Do not reach over or across electrical cables or air hoses 9 Maintain tools with care Inspect Hose Reel and hose periodically and if damaged have them repaired by an authorized technician Page 2 For technical questions please call 1 888 866 5797 Item 46342 10 11 12 13 14 15 16 17 18 19 20 Use the right tool for the job Do not attempt to force a small Hose Reel or attachment to do the work of a larger industrial Hose Reel There are certain applications for which this Hose Reel was designed Do not modify this tool and do not use this Hose Reel for a purpose for which it was not intended Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate too
9. this product but must be supplied by the operator Item 46342 For technical questions please call 1 888 866 5797 Page 3 Assembly Refer to Assembly Drawings on page 7 1 Slide the Handle 3 into the Handle Sleeve 4 then insert the Rubber Sleeve 2 and secure with a Screw 1 creating a handle assembly 2 Insert the handle assembly into the hole on the Link Lever 5 and secure with a Washer 6 and Nut 7 3 Attach the Reels on the Axle and secure with Screw 20 Nut 22 and Washer 21 4 The Air Hose Reel can be attached to the floor ceiling or wall It must be secured to a location that is capable of supporting the weight of the hose reel and hose and also capable of supporting the rotating force exerted when taking the hose on or off the reel In the four holes at the base of the Hose Reel use four 3 8 bolts not included to attach the Hose Reel to the floor ceiling or wall 5 Apply PTFE tape to the Swivel Valve 18 and then thread it on to the Connector 15 6 Apply PTFE tape to the fitting of the lead hose and thread it on the Valve 18 and attach the other end to your compressor 7 Apply PTFE tape to fitting of the extension hose do not exceed 50 of 1 2 hose or 100 of 3 8 hose and thread it on the Connector 15 Turn the Handle 3 clockwise and coil the hose onto the Hose Reel making sure it covers the reel evenly Note The air valves will rotate with the reel when you turn the handl
Download Pdf Manuals
Related Search