Harbor Freight Tools 10 Ton Hydraulic Log Splitter Product manual
Contents
1. Ram Plate 6 Adding attachments to the Log Splitter 3 WARNING Personal injury could result from log or metal pieces flying out at high speed toward the operator or bystanders or the Log Splitter could become damaged Wedge Base 1 Figure 2 4 Fully retract the Ram 5 Remove the stuck log from the Wedge manually with a pry bar SKU 67090 For technical questions please call 1 888 866 5797 Page 6 IMPORTANT Be extremely careful as log pieces may fly off as they separate from the Wedge Do not attempt to re split a stuck log once it has been removed from the Wedge Manually split with a maul or cut with a chainsaw WARNING Remove Split Logs Move each split log away from the Log Splitter Split logs left near the Log Splitter are a tripping hazard To Bleed the Log Splitter 1 2 Extend Ram to its maximum length Remove the Oil Plug 6A and top off oil See Figure 3 below Handle Wheel 36A Oil Plug 6A Piston Rod 18A Figure 3 Turn Handwheel counterclockwise as fast as possible Piston Rod 18A will retract into Ram and push air out of Cylinder 23A via Oil Plug hole Top off oil as needed Replace the Oil Plug and repeat steps 1 3 as needed To add oil remove the Oil Plug and add oil to just below the Fill Plug Then Replace Oil Plug SKU 67090 For technical questions please call 1 888 866 5797 Page 7 MAINTENANCE TO PREVENT AWARNING SERIOUS INJURY FROM EQU2. Air in oil Excessive control valve inlet vacuum Low control valve setting Internal control valve leak Internally damaged cylinder Turn Handwheel clockwise until snug Remove an foreign objects from below Ram Flush and clean the Splitter s hydraulic system Flush and clean the Splitter s hydraulic system Have a qualified service technician repair replace control valve Have a qualified service technician repair replace cylinder piston Move Jack Handles at a faster pace Purge air from Splitter s hydraulic system Have a qualified service technician repair replace control valve Have a qualified service technician repair replace control valve Have a qualified service technician repair replace cylinder Check for excessive air in hydraulic reservoir Check control valve inlet hose for blockage or kinks Have a qualified service technician adjust control valve with a pressure gauge Have a qualified service technician repair replace control valve Have a qualified service technician repair replace cylinder Follow all safety precautions whenever diagnosing or servicing the equipment SKU 67090 For technical questions please call 1 888 866 5797 Page 9 PARTS LIST AND ASSEMBLY DIAGRAM Description Part Description 10 Ram Return Spring 2 Handle Grip 11
3. 4 Turn Handle Wheel 36A counterclockwise no more than one full turn to retrieve the Ram See Figure 2 3 Remove the split pieces 6 Do not use the Log Splitter to split logs across the grain Doing so will damage the Log Splitter and could also cause pieces of log to be thrown 5 Turn Handwheel clockwise until snug injuring the operator or bystanders 6 When finished store the Log Note Many accidents occur when there is Splitter with the Hand Wheel turned more than one person involved in loading counterclockwise one turn to relieve and operating the Log Splitter Only one the hydraulic pressure built up during person should operate at a time Ifa use second person is assisting in loading logs NEVER allow an assistant to hold the log Remove A Stuck Log in place while the operator pulls on the Jack Handles 1 Alog can be stuck on the Wedge Base if the Wedge becomes embedded in the log and the log doesn t completely split and separate 1 Grip one Handle in each hand and This can happen if the log is too pump the Handles in a back and forth stringy or tough to split completely stroke motion See Figure 2 below If this happens follow the directions Pump Handles in back and forth motion below 2 WARNING Never attempt to remove Pan Handle Wheel 36A a stuck log by doing the following ac Handles 3 e Using the hydraulic force of the Log Splitter e Modifying the Log Splitter
4. to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal ac tivity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the com plaint must accompany the merchandise If our inspection verifies the defect we will ei ther repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return re paired products at our expense but if we determine there is no defect or that the defect
5. HexBoltM8x20 2 Jack Handle Lock Spring 6 Ram Plate 1 U Bolt 1 Hex Nut M10 9 Ram 111813 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUALAS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 67090 For technical questions please call 1 888 866 5797 Page 10 PUMP PARTS LIST AND ASSEMBLY DIAGRAM Patt _ Description Qty Small Pump Cylinder lORing 1 O Ring Part Description Qty Big Pump Core Big Pump Cylinder 21A 22A 23A 000 26A 9A SKU 67090 28A For technical questions please call 1 888 866 5797 Page 11 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort
6. IPMENT FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Many maintenance procedures A including those not detailed in this manual will need to be performed by a qualified technician for safety If you have any doubts about your ability to safely service the Log Splitter have a qualified technician service the equipment instead BEFORE EACH USE Inspect the Log Splitter and verify that there are loose or damaged parts AFTER EACH USE Wipe down Log Splitter with a clean soft cloth making sure to clean up any excess or spilled hydraulic oil WHEN STORING Retract the Ram to and turn the Handwheel counterclockwise by one turn to keep the Hydraulic Cylinder Rod protected from corrosion Store the Log Splitter in a clean dry safe location away from children and other unauthorized persons SKU 67090 For technical questions please call 1 888 866 5797 Page 8 TROUBLESHOOTING Possible Cause Possible Solution Ram will not move Slow Ram speed when extend ing or retracting Wood will not split or splits tremely slowly Handwheel is open Wedged wood under Ram Blocked hydraulic lines Blocked control valve Damaged control valve Damaged cylinder piston Slow pumping of Jack Handles Air in oil Damaged control valve Internal control valve leak Internally damaged cylinder
7. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference MACHINERY 10 TON HYDRAULIC LOG SPLITTER Visit our website at http www harborfreight com REV 131 Email our technical support at productsupport harborfreight com ITEM 67090 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2009 by Harbor Freight Tools All rights reserved n s No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning proce
8. dures Write the product s serial number in the back of the manual or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION In this manual on the labeling and all other information provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates DANGER a hazardous 1 situation which if not avoided will result in death or serious injury AWARNING WARNING indicates a hazardous situation which if not avoided could result in death or serious injury 3 CAUTION used ACAUTION with the safety alert symbol indicates a 4 hazardous situation which if not avoided could result in minor or moderate injury SKU 67090 CAUTION For technical questions please call 1 888 866 5797 NOTICE is used to NOTICE address practices not related to personal injury CAUTION without the safety alert symbol is used to address practices not related to personal injury WARNING Read all instructions Failure to follow all instructions listed below may result in fire serious injury and or DEATH The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the ope
9. r These carry important information If unreadable or missing contact Harbor Freight Tools for a replacement Have the Log Splitter serviced by a qualified repair person using only identical replacement parts This For technical questions please call 1 888 866 5797 will ensure that the safety of the equipment is maintained Do not attempt any service or maintenance procedures not explained in this manual or any procedures that you are uncertain about your ability to perform safely or correctly Do not allow anyone to operate the Log Splitter who has not read this manual or has not been instructed on the safe use of the Splitter The Log Splitter owner should instruct all operators in safe Log Splitter operation Store equipment out of the reach of children and other unauthorized persons SAVE THESE INSTRUCTIONS Page 4 FUNCTIONAL DESCRIPTION Specifications Log Cutting Capacity 18 L 6 1 2 Dia Maximum Minimum Log Length 13 1 2 L Ram Stroke 8 1 16 INITIAL TOOL SET UP ASSEMBLY Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagrams near the end of this manual Unpacking When unpacking make sure that the item is intact and undamaged If any part
10. rator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS IMPORTANT SAFETY PRECAUTIONS Set up and use only on a flat level outdoor well ventilated area Wear ANSI approved safety glasses under a full face shield NIOSH approved dust mask respirator heavy duty work gloves hard hat and steel toe work boots during set up and use Keep children away from the equipment especially while it is operating Do not leave the equipment unattended when it is running Turn off the equipment before leaving the work area Page 2 5 Use only accessories that are recommended by Harbor Freight Tools for your model Accessories that may be suitable for one piece of equipment may become hazardous when used on another piece of equipment 6 Stay alert watch what you doing and use common sense when operating this piece of equipment Do not use this piece of equipment while tired or under the influence of drugs alcohol or medication 7 overreach Keep proper footing and balance at all times This enables better control of the equipment in unexpected situations 8 Dress properly Do not wear loose clothing or jewelry Keep hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts 9 Keep the equipment and surrounding area Clean at all times 10 U
11. resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 888 866 5797 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 67090 For technical questions please call 1 888 866 5797 Page 12
12. s are missing or broken please call Harbor Freight Tools at 1 888 866 5797 as soon as possible Please note The Log Splitter is heavy use care and proper lifting techniques when move the Log Splitter Assembly 1 To assemble insert one Jack Handle 3 into each of the sockets on the Ram 9 See Figure 1 above SKU 67090 For technical questions please call 1 888 866 5797 Jack Handles 3 Socket Figure 1 OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT A SAFETY INFORMATION section at the beginning of this manual before use of this product The Splitting Operation Additional Safety Instructions 1 Hold the bark side of logs when loading or positioning never the ends Never place your hands or any body parts between a log and any part of the Log Splitter 2 Never load or unload logs while the Ram 9 is moving 3 Do not pile logs to be split in a place that will make you reach across the Log Splitter in order to load them 4 Log ends that are not cut square can slide out while splitting and cause a safety hazard or cause excessive force to Log Splitter components Use a chainsaw not included to cut logs square on each end before attempting to split them Page 5 5 Never attempt to split more than 2 This action will force the log against one log at a time A piece of log can the Wedge Base and split the log unexpectedly be thrown from the machine causing severe personal injury
13. se the equipment accessories etc in accordance with these instructions and in the manner intended for the particular type of equipment taking into account the working conditions and the work to be performed Use of the equipment for operations different from those intended could result in a hazardous situation 12 Be thoroughly familiar with all controls and with the proper use of the Log 11 Moving parts can crush and cut hands and fingers Keep hands clear of the Ram Plate Wedge and logs while splitting SKU 67090 For technical questions please call 1 888 866 5797 Splitter Know how to stop the Log Splitter and relieve system pressure quickly if needed 13 Make sure all fittings are tight before applying pressure 14 Be aware of the added length of the Log Splitter when transporting 15 Ifalog becomes jammed in the Wedge back off pressure and remove log with a pry bar FIGURE A LOG LOG ORIENTATION ORIENTATION 16 This Log Splitter is designed to split logs up to 18 long and 6 1 2 in diameter lengthwise with the grain only See Figure A 17 Always operate the Log Splitter with all safety equipment in place and in proper working order and all controls properly adjusted for safe operation 18 Always relieve the system pressure before inspecting cleaning adjusting or repairing the Log Splitter 19 This product contains or
14. when used produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm California Health amp Safety Code S 25249 5 et seq 20 When spills of fuel or oil occur they must be cleaned up immediately Dispose of fluids and cleaning Page 3 21 22 23 24 25 26 27 28 29 SKU 67090 materials as per any local state or federal codes and regulations Store oil rags in a bottom ventilated covered metal container Keep hands and feet away from moving parts Do not reach over or across equipment while operating 30 Before use check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the equipment s operation If damaged have the equipment serviced before using Many accidents are caused by poorly maintained equipment 3i Use the correct equipment for the application Do not modify the equipment and do not use the equipment for a purpose for which it is not intended Keep all safety guards in place and in proper working order Never add attachments to the Log Splitter except for authorized accessories supplied by the manufacturer with instructions for safe installation and use Use the Log Splitter only in daylight so you can see what you are doing Never attempt to change the height or speed of the splitting Wedge Maintain labels and nameplates on the Log Splitte
Download Pdf Manuals
Related Search