Harbor Freight Tools 10 ft. x 17 ft. Portable Garage Product manual
Contents
1. 4 a Hem on Cover flap Place strap 7 and flaps inside frame Figure P Door Cover Installation 3 Reconnect the Rail securely to the 5 Use Ratchet Tie Downs 8 to attach the Cover 3 Way Ridge Connector to the Corner Legs 6 see Securing Ratchet Tie Downs on page 10 and Figure R 4 Repeat step 2 for the 3 Way Side Connectors A B A1 A2 so that the Door Cover looks as shown in Figure P and Figure Q Figure Q Wrap Around Side Connectors Figure R Securing Door Cover 6 Repeat steps 1 4 above to install the Back Cover 17 to the other end of the Portable Garage Item 62286 For technical questions please call 1 888 866 5797 Page 11 Roof Cover Installation Note Door and Back Covers 16 17 not shown on 6 Make sure the Bottom Rails are level and horizontal illustrations to provide a clear view of installation 1 Lay the Roof Cover 15 on the ground next to the frame Make sure that the edges with black straps are alongside the Door Back Covers 16 17 and one set of the fabric tubes is facing upwards as shown in Figure S 2 Tie each Rope 18 through an eyelet at the corner of the Roof Cover Figure V Bottom Rails in place 7 Attach the Bottom Rails to the Corner Studs 2 using 3 Way End Rail Clamps 9 Bolts and Nuts 13 14 and to the Center Studs 1 with 4 Way Center Rail Clamps 10 as shown in Figure W Figure S Align Roof Cover with Frame 3 Thr2. Center Stud Corner Stud Bottom Rail Ratchet Tie Down UJ 3 Way End Rail Clamp 4 Way Center Rail Clamp Anchor Cable 1 30cm Cable Clamp M8x50 Hex Head Bolt M8sx50 Round Head Bolt Rope 24 7 3M Concrete Anchor Item not shown Page 14 For technical questions please call 1 888 866 5797 Item 62286 Assembly Diagram MAINTENANCE Item 62286 For technical questions please call 1 888 866 5797 Page 15 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AN
3. D FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state a Harbor Freight Tools Brand 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
4. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference REV 15a 10 Ft X 17 Ft JiS Portable Gara a Harbor Freight Tools Brand Vehicle not included Visit our website at http www harborfreight com Email our technical support at productsupport harborfreight com ITEM 62286 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2014 by Harbor Freight Tools All rights reserved J No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Table of Contents Safely cs gebe ne tds 3 Maintenance noire tite terres 13 Specificatio
5. ded Stud Foot and Leg Assembly 1 Assemble a Foot 7 to the bottom c Secure with a Nut 14 of each Center Stud 1 a Place a Foot onto the bottom of the Center Stud 2 Assemble a Corner Leg 6 to the bottom of each Corner Stud 2 as shown in Figure G 2 f 6 Figure G Corner Leg Assembly b Align the holes and insert a Hex Head Bolt 12 through them Item 62286 For technical questions please call 1 888 866 5797 Page 7 Stud Installation 1 With assistance raise one side of the roof assembly 2 Install the Center Studs 1 into the 4 Way Side Connectors B1 and the Corner Studs 2 into the 3 Way Side Connectors A B A1 A2 with the Corner Legs 6 facing inward Figure H Stud Installation 3 After all four Studs 1 2 are in place 4 Install four Studs on the other side of the rest that side of the assembly on the roof as explained in step 2 above ground and raise the other side 6 Figure I Studs Installed on Both Sides 5 Make sure all parts assembled up to this point are firmly joined together Tap parts together gently with a rubber mallet sold separately if needed Page 8 For technical questions please call 1 888 866 5797 Item 62286 Anchoring Frame AWARNING TO PREVENT SERIOUS INJURY Contact local utility companies to ensure that the installation area is free of pipes cables and other hazards BEFORE installing anchors or choosing installation ar
6. ea 1 Position the frame in the desired installation location 3 Measure the width of the frame at front and back it The location must be flat level and stable should be 10 2 wide with good locations for the Anchors 11 1 The distance diagonally in one direction should be equal to the distance diagonally in the other 2 Level the frame end to end and side to side direction If any measurements do not match adjust the frame and retake measurements until they are equal within a reasonable tolerance Note If measurements cannot be made correct then parts may not be seated together properly SETUP 10 2 Figure J Verify and Adjust Frame Measurements 4 Once the frame is positioned leveled and squared anchor the four Corner Legs 6 as follows a Thread the Anchor 11 1 into the ground near the Corner Leg until the top of the Anchor only extends about 3 above the ground Note Verify that there are no utility lines nearby before driving anchors If there are rocks or other obstacles holes may need to be drilled first to allow proper anchoring Note When anchoring frame on concrete use Concrete Anchor 19 in place of Anchor b Insert a Cable 11 2 through the anchor and through the Corner Leg as shown c Pull the Cable tight and secure it using a Cable Clamp 11 3 Tighten the two nuts on the Cable Clamp evenly to secure the Cable d Repeat for all remaining Anchors Figure K A
7. ion that may affect its safe operation PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts MAINTENANCE a Harbor Freight Tools Brand Item 62286 For technical questions please call 1 888 866 5797 Page 13 m gt Z Oo m Parts List and Diagram Parts List Note Individual part illustrations not to scale 3 Way Ridge Connector 3 Way Side Connector A 3 Way Side Connector B gt N 4 Way Ridge Connector 4 Way Side Connector
8. nchoring and Corner Legs Item 62286 For technical questions please call 1 888 866 5797 Page 9 Securing Ratchet Tie Downs Note Use these instructions in the pages that follow 3 Lift and lower the Ratchet s handle to wind and tighten the strap onto the spindle 1 Thread the strap through the Ratchet s 8 spindle as far as it will go Figure N Tightening Ratchet Figure L Threading Strap through Spindle CAUTION Excessive tightening will damage straps Covers and Corner Legs 2 Insert the S hook of the Ratchet into the hole in the Corner Leg 6 Figure M Inserting Hook into Corner Leg Releasing Ratchet Tie Downs 1 Depress the spring loaded bar on the handle 2 Open Ratchet handle completely 3 Unwind the strap Figure O Releasing Ratchet Page 10 For technical questions please call 1 888 866 5797 Item 62286 Door and Back Cover Installation 1 Position the Door Cover 16 near where you want 2 Disconnect the Rail 4 from the the front of the Portable Garage and turn it so 3 Way Ridge Connector A and place the that the zipper faces the outside of the Portable gap at the top center of the Door Cover Garage and the warning tag faces inside around the Ridge Connector as shown Note that the Door Cover s flaps wrap around the Rafters 3 and the strap is positioned inside the frame DO NOT ATTEMPT TO INSERT ANY FRAMEWORK TUBING INTO THE HEM ON THE COVER FLAPS
9. ns ssseeeeee 4 Parts List and Diagram 14 Assembly eror ai 5 Warranty amaai ranana ae Eae E RR 16 o gt mn m lt a Harbor Freight Tools Brand WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol Itis used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury CAUTION Addresses practices not related to personal injury WARNING marking concerning Risk Double Insulated of Eye Injury Wear ANSI approved i d safety goggles with side shields 9 Canadian Standards Association 4 Raadismamil Betore d A G set up and or use Underwriters Laboratories Inc Page 2 For technical questions please call 1 888 866 5797 Item 62286 IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in serious injury Save all warnings and instructions for future reference The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and sit
10. ow the other ends of the Ropes over the frame 4 Move to the other side of the frame and pull the Cover over the frame Make sure that the Roof Cover is centered on the frame If a small adjustment is needed two people should pull together from the same end of the Portable Garage so that the Roof Cover does not become twisted Figure W 3 and 4 Way Rail Clamp Connections Note Only finger tighten the Nuts at this point Figure T Pulisoot cover over Frame Using Ropes 8 Make sure that all the Bottom Rails are of the same 5 Insert the Bottom Rails 5 into the fabric height from the ground then tighten all Nuts URES On PACH SAS ey Meee Cover 9 Secure the four corners to the Corner Legs 6 18 using Ratchet Tie Downs 8 see Securing Ratchet Tie Downs on page 10 Figure U Insert Bottom Rails Page 12 For technical questions please call 1 888 866 5797 Item 62286 Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE Do not use damaged products If damage is noted have the problem corrected before further use MONTHLY inspect the general condition of the Portable Garage Check for loose ratchet tie downs anchors tube connections and rail clamps tighten as needed torn or frayed covers ropes or cables cracked bent or broken parts and any other condit
11. peration stresses Loose hardware or damaged altered parts will compromise the structural integrity of this product Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement A SAVE THESE INSTRUCTIONS a Harbor Freight Tools Brand Item 62286 For technical questions please call 1 888 866 5797 Page 3 Specifications Overall Dimensions 10 W x 17 Lx9 2 H Center Height Side Height Pole Tubing Diameter o gt mn m lt a Harbor Freight Tools Brand Page 4 For technical questions please call 1 888 866 5797 Item 62286 Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product Note For additional information regarding the parts listed in the following pages refer to Parts List and Diagram on page 14 AWARNING TO PREVENT SERIOUS INJURY Do not leave this product partially assembled Assemble this product completely at one time SETUP Figure A Frame Assembly Overview Item 62286 For technical questions please call 1 888 866 5797 Page 5 Roof Frame Assembly Note Much of this product s assembly is done using slip fit construction Make sure all parts seat completely and securely A rubber mallet sold separately can be used to gently tap parts in place to ensure a
12. tight fit B1 te SS SS B1 B1 Figure B Roof Assembly Overview 1 Assemble ridge using three Rails 4 with A 4 4 Way Ridge Connectors B between them and a 3 Way Ridge Connector A on each end The Rails connect to the straight ends of the Connectors and the curved free ends of the Connectors angle down as shown in Figure C Figure C Ridge Assembly 2 Connect a Rafter 3 to each free end of every Connector A B as shown in Figure D A Figure D Rafter Assembly Page 6 For technical questions please call 1 888 866 5797 Item 62286 3 Assemble a roof side rail using a 3 Way B1 Side Connector B A2 three Rails 4 with A2 B1 4 Way Side Connectors B1 between them and then a 3 Way Side Connector A A1 on the other end see Figure E The Rails connect to the straight ends of the Connectors and the curved ends of all Connectors must 4 face up angled the same direction as shown If Figure E Roof Side Rail Assembly that is not the case incorrect connectors were used or they were assembled backwards 4 A1 4 Assemble a second identical roof side rail 5 Connect the roof side rail assemblies to the by repeating the instructions in step 3 ends of the Rafters 3 as shown in Figure F SETUP Figure F Roof Side Rail Installation 6 Make sure all parts assembled up to this point are firmly joined together Tap parts together gently with a rubber mallet sold separately if nee
13. uations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Assembly Precautions 1 Do not assemble in windy conditions 2 Assemble and install only on flat level hard surface 3 Assemble and anchor only according to these instructions Improper assembly or inadequate anchoring can create hazards 4 Wear ANSI approved safety goggles and heavy duty work gloves during assembly Use Precautions 1 Do not use grill or any other type of fire under cover Cover may catch fire if exposed to heat rising from fire 2 Do not allow snow or debris to accumulate on this item 3 Heavy wet snow or strong wind could cause damage or sudden collapse Remove the Cover when these or similar conditions are expected 4 This product is not a toy Do not allow children to play with or near this item SAFETY Keep assembly area clean and well lit Keep bystanders out of the area during assembly Do not assemble when tired or when under the influence of drugs or medication Product capabilities apply to properly and completely assembled product only Use as intended only Do not use for long term shelter Inspect regularly tighten all loose hardware and loose cords and secure all loosened anchors If any parts are damaged bent or stretched they must be replaced Hardware may loosen during normal o
Download Pdf Manuals
Related Search