Harbor Freight Tools 10 ft. x 17 ft. Portable Garage Product manual
Contents
1. 4 Throw the ropes over the top of 5 From the other side pull the ropes to p the frame to the other side properly position the Top Cover 6 Remove the ropes and Bottom Rails 7 Secure all four Top Cover corners to the outside of the Corner Legs with Ratchets See Figure J Figure L Page 8 For technical questions please call 1 800 444 3353 Item 60727 8 Unzip and roll up the Front Cover 10 From the inside slide one Bottom Rail into each segment of the pocket between the legs 9 Install Bungee Cords 15 to secure the Front Cover 11 On the corners secure Bottom Rails to Corner Legs with Corner Clamps 14 Bolts 17 and Nuts 20 12 In the middle secure Bottom Rails to Middle Legs with Middle Clamps 13 Bolts 17 and Nuts 20 Note To prevent tearing fabric position all Bolts so that the bolt heads are against the fabric Bottom Rails inside pocket 17 not visible Bungee Cord 15 Figure M Corner Middle Clamps 14 Clamps 13 a mM uw N 7 lt Figure N 13 Now that assembly is done tighten all connections with a wrench sold separately Make sure all connections are properly tightened before use Do not overtighten a Harbor Freight Tools Brand Item 60727 For technical questions please call 1 800 444 3353 Page 9 gt A on m z e lt Maintenance Procedures not specifically explained in this manual must be performed o2. Blvd PO Box 6009 Camarillo CA 93011 800 444 3353
3. OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record Note Some parts are listed and shown for month and year of purchase instead illustration purposes only and are not available individually as replacement parts Page 10 For technical questions please call 1 800 444 3353 Item 60727 Parts List Note Individual part illustrations not to scale Bungee Cord Stabilizer Bolt 1 4 x 1 5 8 Middle Leg 74 Corner Leg 63 2 3 Rafter 42 1 3 Bolt 1 4 x 1 7 8 Bottom Rail 60 oO Bolt 1 4 x 2 Ridge Rail 57 1 4 Part 5 Swaged Top Rail 61 1 2 G Q Nut 01 4 Anchor 15 Wire Rope Clamp Ratchet N oO N N Middle Foot 3 Way Connector N oO 4 Way Connector N O N N N N N k i oi A N oOo on Middle Clamp Corner Clamp MAINTENANCE Item 60727 For technical questions please call 1 800 444 3353 Page 11 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage du
4. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference 10 ft x 17 ft JiS Portable Garage a Harbor Freight Tools Brand Patent No US20120234418 A1 D40931 0 7296584 Visit our website at http www harborfreight com Email our technical support at tech harborfreight com ITEM 60727 When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved i S No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Table of Contents SAE enira EAE 3 Maintenante ccce 10 Specifications ccccc
5. e directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state a Harbor Freight Tools Brand 3491 Mission Oaks
6. ecceeeeesessecseceeeeeeees 4 Parts Listini n a 11 Assembly eee 4 Warranty 00 eecceceeeeeeeeeeeeeeececeeeeeeeeeeeteeteees 12 a Harbor Freight Tools Brand WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury CAUTION Addresses practices not related to personal injury WARNING marking concerning Risk WARNING marking concerning of Eye Injury Wear ANSI approved Risk of Head Injury Wear hard hat safety goggles with side shields during assembly and service WARNING marking concerning Risk of Hand Injury Wear heavy duty work gloves during assembly and service Read the manual before assembly and or use Page 2 For technical questions please call 1 800 444 3353 Item 60727 IMPORTANT SAFETY INFORMATION AWARNING Read all safety warnings and instructions Failure to follow the warnings and instructions may result in serious injury Save all warnings and instructions for future reference The warnings precautions and instructions discussed in this instructio
7. hould measure 10 2 Position the frame in the desired location b The distance diagonally in one direction A should be equal to the distance diagonally in the other direction B c If the measurements do not match adjust the frame and measure again until they are equal Figure D 4 Once the frame is positioned leveled and squared anchor the Corners gt A on m z a lt WARNING Anchor only according to b Insert a Wire Rope 22 through the these instructions Improper assembly or Anchor and Corner Foot inadequate anchoring can create hazards c Tighten the Wire Rope and secure it using a Wire Rope Clamp 23 Tighten the nuts evenly CAUTION To prevent tripping hazard position Anchors toward the interior of d Repeat on the other corners the frame close to the Corner Feet a Use a metal bar sold separately to thread the Anchor 21 into the ground until the loop at the top of the Anchor extends just above the ground Wire Rope Wire Rope 22 Clamp 23 Figure F Note Middle Feet can be anchored to increase stability Figure E Page 6 For technical questions please call 1 800 444 3353 Item 60727 Attach Front and Back Covers 1 Position the Front Cover 25 so that the zippers 5 Remove the Top Rail from the face outside and the warning label faces inside Stabilizer on the left side 6 Place the strap over the Stabilizer then reattach the Top Rai
8. l 7 Tighten the strap by pulling on these ends so that the flaps wrap around the frame 8 Repeat steps above on the right side Strap Top Rail Front Cover 25 Figure G 2 From the inside remove the Ridge Stabilizer Rail from the 3 Way Connector Figure 3 Place the strap over the 3 Way Ridge Connector 9 Attach the Back Cover 26 in the same manner then reattach the Ridge Rail 10 From the inside secure Front and Back Covers 4 Tighten the strap by pulling on the ends so borne Corner Legs Witt Ralche 27 that the flaps wrap around the frame a Insert the Ratchet s S Hook through the hole on the side of the Corner Leg 3 Way Connector b Thread the strap through the Ratchet Strap spindle then pull up on the strap c Raise and lower the Ratchet handle to tighten the strap gt a LLI lt d Repeat for the other corners Note To avoid damaging the straps do not overtighten the Ratchets Ridge Rail Figure H Figure J Item 60727 For technical questions please call 1 800 444 3353 Page 7 Attach Top Cover 1 Lay the Top Cover 24 on the ground 2 Slide two Bottom Rails 5 into the next to the frame so that the inside pocket middle openings of the pocket for the opposite side is facing up 3 Tie a rope sold separately to each Bottom Rail Top Cover gt 24 n u Figure K WE
9. n manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAFETY Assembly Precautions 1 Do not assemble in windy conditions 6 Wear ANSI approved safety goggles heavy duty work gloves and hard hat 2 Assemble and install only on during assembly and service flat level hard surface 7 Keep assembly area clean and well lit 3 Assemble and anchor only according to these instructions Improper assembly or 8 Keep bystanders out of the area during assembly inadequate anchoring can create hazards 9 Do not assemble when tired or when under 4 Check for utility lines tree branches and the influence of drugs or medication other structures before assembling 10 Product capabilities apply to properly and 5 Verify that installation surface has no completely assembled product only hidden utility lines before anchoring Use Precautions 1 DO NOT USE IN HIGH WIND Remove cover if harsh weather or heavy rain threatens T Use as intended only 8 Inspect regularly tighten all loose hardware and 2 For temporary use only loose ropes and secure all loosened anchors Do not use for long term shelter If any parts are damaged bent or stretched they must be replaced Hardware may loosen during 3 Do not use as tent Does not meet ten
10. nly by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE Do not use damaged products If damage is noted have the problem corrected before further use Inspection MONTHLY inspect the general condition of the Portable Garage Check for e loose ratchet tie downs anchors tube connections and rail clamps tighten as needed e torn or frayed covers ropes or wire ropes e cracked bent or broken parts and e any other condition that may affect its safe operation Cleaning 1 Immediately remove any accumulated 2 PERIODICALLY clean cover with mild debris from the cover with a broom mop soap and water DO NOT use bleach or other soft sided instrument from the or harsh abrasive products outside DO NOT use sharp instruments PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYERASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO
11. semblies using 3 Way Connectors 11 Rafters 3 Roof Corners 10 Stabilizers 16 Corner Legs 2 Corner Feet 9 Bolts 17 18 19 and Nuts 20 Lb m J oA Figure A End Assembly Page 4 For technical questions please call 1 800 444 3353 Item 60727 2 Construct two Middle Assemblies 4 Way Connectors 12 Rafters 3 Roof Corners 10 Stabilizers 16 Middle Legs 1 Middle Feet 8 Bolts 17 18 19 and Nuts 20 17 20 hem Figure B Middle Assembly 3 Attach a Ridge Rail 6 and two Top Rails 4 to 5 Attach another Middle Assembly a Ridge Rail 6 one End Assembly with Bolts 18 and Nuts 20 and two Swaged Top Rails 7 to the previous gt section with Bolts 18 and Nuts 20 l 4 Attach a Middle Assembly a Ridge Rail 6 ao and two Swaged Top Rails 7 to the previous 6 Attach the other End Assembly to the previous section with Bolts 18 and Nuts 20 section with Bolts 18 and Nuts 20 7 lt End Assembly J Middle Assembly End _ Middle Assembly Assembly Figure C Frame Assembly Item 60727 For technical questions please call 1 800 444 3353 Page 5 Anchor the Frame 1 WARNING Verify that installation surface has no 3 Level the frame end to end and side to side hidden utility lines before installing anchors Install only on flat level hard surface a Measure the width of the frame at front and back They both s
12. t normal operation stresses Loose hardware flammability standards Do not use grill heater or damaged altered parts will compromise or ignition sources inside or near cover the structural integrity of this product 4 Do not allow snow rainwater or debris 9 Maintain product labels and nameplates to accumulate or pool on cover These carry important safety information If unreadable or missing contact 5 Do not hang objects from any part of the Garage Harbor Freight Tools for a replacement 6 This product is not a toy Do not allow children to play with or near this item A SAVE THESE INSTRUCTIONS Item 60727 For technical questions please call 1 800 444 3353 Page 3 gt A on m z e lt Specifications Overall Dimensions 10 W x 17 L Side Height Center Height C Pole Diameter Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY Do not leave this product partially assembled Assemble this product completely at one time Note At least 3 workers are required for assembly Before starting assembly review the instructions and make sure there is enough time and the proper tools available to properly assemble Finger tighten all connections until assembly is done Assemble on a flat level surface Frame Assembly 1 Construct two End As
Download Pdf Manuals
Related Search