Harbor Freight Tools 1/4 in. Drive Click Type Torque Wrench Product manual
Contents
1. ACAUTION 1 Procedures not specifically explained in this manual must be performed only by a qualified technician TO PREVENT INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use BEFORE EACH USE inspect the general condition of the tool Check for loose hardware misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation If the Torque Wrench has not been used for some time turn the knurled handle clockwise and counterclockwise several times to re lubricate the internal workings Then operate at a low torque setting several times This ensures proper operation Do not turn knurled handle below the lowest torque setting 3 Wipe Torque Wrench with a cloth to clean Do not immerse in any cleaning solution This would damage the internal lubrication 4 Every 6 months have the Wrench calibrated and serviced by a qualified technician Note Replacement parts are not available for this item PITTSBURGHEZ 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 57972. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference P T TTSB UR G H PROJ ITEM 61277 Click Type Torque Wrench Visit our website at http www harborfreight com Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2013 by Harbor Freight Tools All rights reserved p No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Torque Range 20 200 in lb Important Safety Information l WARNING Read all safety warnings and instructions Failure to f
3. ollow the warnings and instructions may result in injury Save all warnings and instructions for future reference The warnings cautions and instructions 4 Use as intended only Do not use as discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this hammer or pry bar Do not use handle extension to increase force Do not drop Inspect before every use do not use if damaged or if parts are loose product but must be supplied by the operator 6 Keep away from children A EAA APPO a aay goggles and 7 For your safety service calibration heavy duty work gloves during use and maintenance should be performed 3 Use only within rated torque range regularly by a qualified technician Do not use for loosening 8 Use only sockets with the correct drive and rated to at least the torque that will be applied to it Operating Instructions Clean and or repair the threads that will be tightened Damaged or dirty threads will result in a misleading torque reading Knurled Handle Select the desired socket and verify it fits Drive Anvil properly on the nut or bolt being tightened Lock Knob Torque Settings 1 Wear ANSI approved safety goggles and heavy duty work gloves Page 2 For technical questions please call 1 888 866 5797 Item 61277 e
4. y 4 Press the socket firmly onto the drive anvil 5 Turn the Lock Knob at bottom of the Handle counterclockwise until it stops 6 Turn the handle to set the torque To set to 55 for example 7 A a Turn the knurled handle CW or CCW until the 0 graduation on the bevel edge lines up with 50 See illustration A above 9 10 11 Item 61277 For technical questions please call 1 888 866 5797 B The 50 line is shown in grey because it will likely be hidden at this point b Continue turning the knurled handle about a half turn clockwise until the 5 graduation mark lines up with the centerline It is now set for 55 See illustration B above Retighten the Lock Knob by turning it all the way clockwise O 7 Direction Switch Set the Direction Switch for clockwise or counterclockwise operation The Switch shown above is in position for clockwise operation Place socket onto the nut or bolt and pull the handle gradually in the desired direction until a click is heard or felt Do not pull beyond that point the click indicates that the torque setting has been reached Stop pulling and the Torque Wrench will automatically reset When finished loosen the lock knob and set the Torque to the lowest torque setting not lower than the lowest setting before storing inside case indoors out of reach of children Page 3 Maintenance and Servicing A
Download Pdf Manuals
Related Search