Harbor Freight Tools 1/2 in. _ 1 in. Ratcheting Pipe Threader Set Product manual
Contents
1. Figure C 9 To disengage the Die after threading is complete pull out the reversing Knob turn it 180 degrees until the arrow points in the opposite direction and drop it back into place Use the Handle to rotate the Ratchet Holder until the Die disengages fully from the pipe end 10 When sliding the pipe out of the Ratchet Holder be careful not to damage newly cut threads Items 62353 62354 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a gualified technician AWARNING TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged eduipment If abnormal noise or vibration occurs have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general 2 DURING USE ensure that pipe end and condition of the tool Check for die threads are oiled with Thread Cutting Oil not included at all times loose hardware misalignment or binding of moving parts 3 AFTER USE wipe external surfaces of the tool with clean cloth cracked or broken parts and e any other condition that may affect its safe operation To replace the Die Blades Worn Die Blades can result in poor thread 4 Insert four new Die Blades into the Die quality When replacing Die Blades verify that the size of the new Die Blades corresponds to the NOTE When inserting the Die Blades make sure the size of the Die To replace the Die B2. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference J MACHINERY RATCHETING PIPE THREADER SET Item 62353 shown ITEMS Visit our website at http www harborfreight com 62353 62354 Email our technical support at productsupport harborfreight com REV 14d When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2014 by Harbor Freight Tools All rights reserved n F No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Table of Contents TE RE EEN ER 3 Maintenance Se SEER Ge E 12 Specifications ee ee Re AR ee 8 Parts L
3. chnician The handles must be kept clean dry and free from oil and grease at all times Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Fully engage the direction switch in the in or out position before use WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e Lead from lead based paints e Crystalline silica from bricks and cement or other masonry products e Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built int
4. ist and Diagram sesse ese ee 14 SELUD ER ER RE ER EE GR ER ee 8 ETE Ee 16 Operation ss vied Ee Sk HEG 9 CENTRAL CS MACHINERY WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARN l NG Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided ACAUTION could result in minor or moderate injury NOTICE CAUTION Addresses practices not related to personal injury Specifications 3 8 18 TPI 1 2 14 TPI 3 4 14 TPI Die Sizes 1 11 5 TPI 1 1 4 11 5 TPI 1 2 14 TPI 3 4 14 TPI 1 11 5 TPI 1 1 2 11 5 TPI 2 11 5 TPI Kit Includes Ratchet Head with Coupler 3 Handles Ratchet Head with Coupler 2 Handles 7 Dies and Blowmold Case 3 Dies and Blowmold Case Page 2 For technical questions please call 1 888 866 5797 Items 62353 62354 IMPORTANT SAFETY INFORMATION 1 Wear ANSI approved safety goggles and heavy duty work gloves during use Keep work area clean and well lit Keep bystanders out of the area during use Do not use when tired or when under the influence of alcohol drugs or medication This product is not a toy D
5. lades cutting edges of the Die Blades face inward and that the number on each Die Blade is at the top and in sequence 1 Remove the four Screws on the Die 5 Once the Die Blades are properly inserted 2 Remove the Cover from the Die replace the Cover and four Screws 3 Remove all four Die Blades Cover Die Blade Blade Number Die Record Serial Number Here Note If product has no serial number record Note Some parts are listed and shown for month and year of purchase instead illustration purposes only and are not available individually as replacement parts Items 62353 62354 For technical questions please call 1 888 866 5797 Page 5 Parts List and Diagram 62353 art Qty Part Qty 2F 3 8 Die Ratchet Coupling 1 1 2 Die Blade Set 4 3 8 Die Blade Set 2 DieScrew 112 Die Cover G 2 Die Ratchet Couping 1 1 2 Die Ratchet Coupling G 2 Die Blade Set 1 2 Die Blade Set 5 4 Die Cover 7 c 3 4 Die Die Blade Set 1 Die Screw 1 Die Ratchet Coupling 1 Die Blade Set 1 1 4 Die Screw 1 1 4 Die Cover 1 1 4 Die Ratchet Coupling Handle Connector 1 1 4 Die Blade Set Oil Can 1 1 2 Die Screw Page 6 For technical questions please call 1 888 866 5797 Items 62353 62354 Parts List and Diagram 62354 art Qty Part Qty 1 2 Die Cover 1 6 Ratchet J1 1 2 Die Ratchet Coupling 7 RatchetHolder 1 1 2 Die Blade Set 8 Plate aa 9 Scew 6 3 4 Die Cover 3 4 Die Ratche
6. o not allow children to play with or near this item Use as intended only Do not use handle extension to increase force Inspect before every use do not use if parts are loose or damaged Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Keep pipe lubricated with cutting oil not included 10 Secure pipe to be threaded in clamp before use 11 Read manual before set up and or use 12 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 13 Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool Do not use a tool for a purpose for which it was not intended 14 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recommended when working Wear restrictive hair covering to contain long hair Items 62353 62354 15 16 17 18 19 For technical questions please call 1 888 866 5797 Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have them repaired by an authorized te
7. o this product but must be supplied by the operator Page 3 Operating Instructions 1 Assemble the Handle Rod parts and insert threaded portion of Handle Tube into the Ratchet Holder 2 Determine the size of the pipe to be threaded 3 Pick the appropriate Die to be used Die sizes are stamped on the outside of each Die 4 Place the rear of the Die over the end of the pipe to be threaded Verify that the inside diameter of the Die matches the outside diameter of the pipe see Figure A These measurements should be equal Figure A 5 Insert the Die into the Ratchet Holder Itis a force fitting and once the Die is in the Ratchet Holder it may require light tapping with a wooden mallet to remove the Die see Figure B Figure B Page 4 For technical questions please call 1 888 866 5797 6 Fill an Oil Can with Thread Cutting Oil not included Keep it nearby during the threading operation CAUTION Make sure the pipe end and threads of the Die are sufficiently oiled at all times Otherwise Die life will be shortened and the threads will be rough 7 Make sure that the pipe to be threaded is properly secured in a vise 8 While applying pressure to the end of the pipe use the Handle to rotate the Ratchet Holder around the pipe to engage the Die with the pipe end see Figure C Continue this operation until the desired thread length is achieved Die Pipe Knob Ratchet Holder Handle
8. rmal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state CENTRAL CS MACHINERY 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
9. t Coupling 3 4 Die Blade Set 12 Spring dT 1 Die Screw 13 knob tt Die Cover 1 Die Blade Set Items 62353 62354 For technical questions please call 1 888 866 5797 Page 7 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFAGTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS OUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS OUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation no
Download Pdf Manuals
Related Search