Haier HWM75-276S User's Manual
Contents
1. Is the drain hose frozen Is the drain hose blocked by foreign material Are there laundries falling to the outer side of the spin tub There s abnormal sound during washing Are there hair pin coins or metal items brought inside the tub There s abnormal sound and violent vibration during spinning e Is the machine slanting Is the gland pressed evenly Are there laundries falling to the outer side of the spin tub Are the laundries in spin tub too much There may be some water flowing out of the drain hose in the first use of the machine t is the water remained in the factory inspection of performance 15 Packing list Name Quantity e User s manual One piece Water inlet hose e One piece e One piece Lint filter s Slane 9 One piece Twin tub washing machine One set Specification iw ater level Water quantity about Maximum 55L Medium 46L Minimum 36L Rated washing capacity kg 12 Rated spinning capacity kg 6 8 Injection pressure MPa 0 02 0 2 162. atob Do not wash it directly by water after each using 9 Pull off the power plug and hang up the power cord Hang up the drain hose Wipe off the water drops on the surface and inside the tub with clean soft cloth Open the cover of the wash tub and the inner outer cover of the spin tub for some time about one hour then close them 13 Trouble shooting Answer to question When the remained water is frozen Prevent the freezing be sure to discharge the water completely after using 9 After complete draining set the WASH SELECTOR at GENTLE or STANDARD If it is set at DRAIN it will be rather difficult for the frozen water to melt 9 When the water is frozen Pour hot water below 50 C into the wash tub to soak it completely Then turn the pulsator with hands gently Please confirm the drainage can work normally before next using 14 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomena The machine does not act The reason Is there power failure Is the power plug loose Is the pulsator twisted by foreign materials The draining does not work
3. cle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more 9S 9 i Safety precautions Do not stretch hands into the working machine lt is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc Handicapped or children without care shall not use the machine Keep the machine away from direct sunlight and heat source like the To protect your laundries and wash ing machine please take out all ofthe coins buttons sand hairpin and other foreign materials before washing Please check if the water faucet is open and if the connection of the water inlet pipe is proper e itis suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Usage of the drain hose The drainage shall be smooth with the drain hose 1 The height of the drain hose shall beless than 1 2m or the drainage will not be smooth enough and cause incomplete drainage Insert the water inlet hose into the water filling entrance
4. er cover of The spin tub Inner cover of The spin tub 3 Spin for 1 2 minutes 3 Run the foam removing spinning 1 Open the outer cover of the spin tub 2 Set the water filling selector control rod at the SPIN side Fill water for about 1 minute If the water quantity filled is too large the water may flow out from the wash tub side Please twist the water tap to limit the water filling 3 Close the outer cover of the spin tub Spin for 1 2 minutes Rinse with water filing Lc iji 1 Put the laundries into the wash tub Select OVERFLOW suitable current according to the laundries If you find water 2 Adjust the water level flowing out here Set the water level with water level adjusting please twist the lever according to the laundries quantity hired ra a Then fill suitable water continuously SANS v Ing 3 Rinse Adjust the wash timer to 5 7 minutes to do rinsing Repeat the midway spinning and rinsing with stored water for 2 3 times Rinse with stored water 1 Put the laundries into the wash tub Select suitable current according to the laundries 2 Fill water to preset water level 3 Rinse Adjust the wash timer to 2 3 minutes to do rinsing When the laundries quantity is below 2 4kg please use Gentle current f you use Standard current it may splash 10 1 Put the laundries into the spin tub evenly and smoothly Selection of the spin time Spin
5. ersonal safety ofthe user Forbidding sign Please check if the power receptacle has good earthing condition before using to guarantee your safety Safety precau Please insert the power cord into special receptacle with rated vol tage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector m tions When the machine is normally using please put the power plug at the location easily to be insert ed and extracted by hand Be sure to pull the plug off when there s power failure or the machine is being moved cleaned orwhen it is idle If the power cord is bad to avoid risk it is required to replace it by the technicians ofour special shop or the Keep the pin of the power plug clean Do not put the machine at damp place like the bathroom Never wash it with water Do not place wet laundries on the control panel after sale service department Do not use water hotter than 50 C In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet Ventilation hole at the bottom of the washing machine 9 Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning Do not let the machine share one recepta
6. m water level for laundries less than 2 4kg so as to avoid splashing of water e It is suggested not to use high sudsingdetergent Usage of the detergent How to use the whitener How to use the washing powder Fill water to decided level Dilute eDirect dissolved in the machine the whitener with container 1 Fill small quantity of water Pour it slowly into the washing tub 2 dd the powder Run for 30 seconds to dissolve it completely 3 Put it in the laundries Select suitable e Avoid using whitener on laun water level dries with color or pattern as they are prone to lose color prone n The instant dissolving of the washing powder e The whitener shall not touch 1 Prepare warm water of 30 C and a the laundries directly container e Refer to the user s manual for 2 Add the powder while stirring to fully i dissolve it tech and quantity of he The powder is more prone to pollute the laundries than the detergent Therefore please use it with proper quantity e Dosage of different washing powder is different Please refer to the instruction of the washing powder for the detail dosage For powder whitener please dissolve it before using Washing sequence Wash selector standard current gentle current Water filling selector handle Wash timer _ Water filling entrance Overfilling sig ty set to below 2 minute callus first get to 5 minute then Buzzer Spin timer urn i
7. nd hairpins close zippers etc So The quantity of the laundries shall not be too large Stretch and loosen the laundries before putting them in the tub YG is running buttons of the laundries may cause noise For the sake of discretion please put the laundries with buttons into other laundries Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other laundries Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur tum it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly The musts in washing The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time Laundries quantity in one washing cycle shall be lower than the rated capacity 9 The thickness size type of the cloth will influ ence the actual washing capacity Itis suit able to put in reasonable amount of laundries and the laundries can be turned round in wash ing for one time washing D not select Maximu
8. on Water inlet hose the control panel directly Pull it out to dismantle it Waterfiling Select water level according to the quantity of the laundries Adjust the water level adjusting lever to desired water arcing level level line Attention In water filling do not exceed the Maximum water level Med Otherwise the water may overflow out of the washing Mini machine ua Maximum Nes about 55L imu ut 36L Install the lint filter After opening the package please take out the lint filter from the document bag install it to the overflow filter of the wash tub See to the figure Overflow filter int filter How to change the direction of the drain hoses N e Figure 1 indicatesthe ex factory installation position ofthe drain hose Extend the drain hose from theside of spin tub les Vir Take off the drain hose fromthe hanging prain hook Figure 1 hole of thecabinet Pull thedrain hose fixing hook outwards gently to takeout Side Sectional view the drain hose from the twofixing hooks SA As per Figure2 Rraln hose installation hole 5 Pull outwards a Drain DE Rotate the drain hose fixing hook for 90 slightly Y to take it out from theinstallation hole Jakson i Figure 2 As per Figure 3 SERUUM FS Install the two drain hose fixing hooks taken out into the installation hole at the other side ofthe base frame nus hois accurately you ean Cp eee poek prie a ccu y y
9. ou to fix it lean the washing machine Takeoff the fixing Insert the fixin A forward slig htly Then rotate hook downwards Cc hole upwards for 90 As per Figure 4 Rotate the fixin Figure 3 Figure 4 Pull the fixing hook outwards slightly Inlay the drain hose into the fixing hooks reliably along the groove at spin tub side and make it extend towards spin tub side Then hang the drain hose into the hanging hole at the spin tub side As per Figure 5 Figure 5 Extend the drainhose from therear side Take out the drainhose from the fixing hook Extend itfrom the rearside When the drain hoseis extended fromthe rear side it canbe hung onthe point fordrain hose at the two sides ofthe cabinet See to Figure6 a y 5 V Figure 7 FE Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put the drain hose up to suitable position 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Check if the laundries has special requirement on washing Clear the Tie the long pocket Take strips fasten out the coins the buttons sa
10. rs manual Twin tub Washing Machine with Pump USOS E This manual is for HWM75 276S e Please read this manual carefully before using Retain it for future reference 0030806004E Contents xe Names of the parts eese eere rere Safety precautions rrr RE Rn Installation and adjustment Preparation before washing The musts in washing eese Usage of the detergent eere Washing sequence WO 2 39 3 2 2 2 2 2 2 2 2 2 3 2 3 3 3 3 3 3 3 aon Disposal after washing Trouble Shooting Answer to question Packing list Specification Names of the parts Buzzer Water filling entrance Water inlet selector handle Wash selector Wash timer Control panel Overflow filter Water level adjusting lever Outer cover of the spin tub Inner cover of the spin tub Lint filter Installed by user Valve cover Pulsator Wash tub Drain hose Wash tub cover Base frame Meaning and description of the symbols Contents marked with that symbol are related Warning sign to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety ofthe user Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the p
11. t back it can increas the service life of the timer The buzzer will ring when Ho sel tae ta al the washing finishes turn it back it can increase the service life of the timer BUZZER Wash 1 Water filling selector WASH SEN 1 Set the water filling selector at the WASH side aana Figure 1 Figure 1 2 Set the water level adjusting lever to needed line 2 Fill the water and add the dissolved washing powder to make the water level reach the preset position Figure 2 Run washing program for some time to stir and dissolve the powder completely Figure 2 E STANDARD w DRAIN 3 Put in the laundries If the water quantity is e insufficient please add water KN Figure 3 4 Select the current Select the strength of the current according to the laundries Figure 3 5 Select the washing time Select the washing time according to the laundries Figure 4 9 WASH TIMER Figure 4 STANDARD GENTLE 6 After washing the buzzer will ring Set the WASH EN SELECTOR at DRAIN Figure 5 JT WASH SELECTOR Figure 5 Midway spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Spin 1 Put the gland in properly Please put in the gland properly even if the laundries quantity is small Push Gland t Bb Proper The laundries Proper No gland are slanting 2 Close the inner and outer cover of the spin tub Out
12. time 2 Press the gland in the tub properly Laundries minutes Close the inner and outer cover of Bed sh the spin tub pedsheetor About 4 5 Underwear 4 3 Spin knitwear About 2 4 Select suitable spin time according Swear j About 1 2 to the laundries and do spinning chemical fiber out 1 Blending thin t lak nda Within 1 minute During spinning if there s abnormal sound it is generally owing to slanting placement of the laundries Please stop the machine and re order the laundries n spinning it will pause the work if you open the outer cover of the spin tub Close it to resume the spinning To do spinning and dhana or rinsing with water filling together please first do X9 spinning for around 1 minute gt then do draining or rinsing with water filling Otherwise the spinning will stop owing to too much water stored in the spin tub 11 Disposal after washing e After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine e Please first pull off the power plug from the receptacle before cleaning Cleaning the lint filter The lint filter must be used during washing 9 t must be cleaned in time after each using 1 Take off the lint filter Put hand at the indicated position Push down to take it off See to Figure 1 Clean the lint Put it in water and clean
13. while it is still wet See to Figure 2 Install the lint filter After cleaning insert the bottom Figure 2 of the lint filer marked with down side into the overflow filter then push the upper part of the filter in marked with up side See to Figure 3 Figure 3 Cleaning the overflow filter Too much lint on the overflow filter will influence the normal usage of the machine Please clean it every two months 1 Take off the overflow filter As indicated in the figure nip the elastic fixing claw and pull it to the direction of the arrow to take it off Elastic fixing claw 12 Cleaning the overflow filter 2 Take off the corrugation pipe Dismantle the upper part of the eee corrugation pipe inside the adjusting lever overflow filter as indicated in Contidati n Figure 1 Pipe Cleaning the overflow filter Clean the lint around the filter and flush with tap water Figure 1 Install the overflow filter 1 Install the corrugation pipe 2 Insert the mounting plate at the bottom of the filter into the valve cover 3 Hang up the hook at the left upper side 4 Push the upper part in as Figure 2 indicated in Figure 2 Disposal of the complete unit Wipe the complete unit with soft e After washing dismount the water inlet cloth twisted dry hose e Do not store water in the tub for lon Wipe withneutral detergentif too diny period Discharge the water iri medi
Download Pdf Manuals
Related Search