Haier Washer HWM100-828A User's Manual
Contents
1. 3 Ys AO a Check if the laundries are applicable for washing with machine b Divide the laundries with unfast color from other laundries c Put those laundries difficult to absorb water into water with hand d For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent in advance which can make it easier to remove the soil e For those laundries that may get lint ball and those with long fur turn it over before putting in f Do not put those laundries polluted by chemicals directly into the washing machine g For those small laundries and those may get twisting or worn and woollen fur laundries please put them into mesh bag for washing2. can bechoosen between 4 8 level blanket water level ofthe program to select between 2 5 In common strong children standards and the memoryprocess the rinse waterwhen washing the waterlevel higher than that ofa file the highestwater level and artificialselection except when rinsewater G AIR DRY button Push the AIRDRY button to select air dryprocedure The program ischosen 0 5h 1 0h 2 0h 0 5 1 0h The purposeis drying theinner tub andthe outer tub which can avoidgrowing mildew on the outer tub andthe inner tub 2 0h can dry laundries The max drying capacity of the fibre laundrie is2 0 kg e AIR DRY program cannot be reserved H RINSE button For the MEMORY BLANKET CHILD STANDARD programs push the RINSE botton lightis flashing then push select the rinse times Overflow rinse 1 2 3 For ECONOMY WOOL programs press RINSE button can not change time The button isunavailable from the SPEEDY andTUB DRY programs 12 Adjust the Installation position The largest allowable slope of the shank base of the machine is 2 The slanting or rough ground will result in unstable running or stoppage of the machine Please adjust it with following methods Confirm it s horizontal Hang the lead line to check if it is horizontal Adjust the adjustable leg 1 To twist the adjustable leg please first lift up the side of the leg slightly loosen the adjustable nut the adjustable nut and twist
3. the cover then lift the machine up gently L G J H E F C B pipe hook Indicator mode and meaning off Flashing indicating the running program On indicating the program about to run or the selection mode Child lock function The function isintended for children safety and preventingthe washing programfrom accidental changes by children Unhinge clamp outlet Figure 1 Figure 2 Figure 3 Remarks in order to make sure of the correct of installation it is suggested to change the direction of the drain hose with our company serviceman e Push and hold the water levelbutton and spin button then pushdown the poweron off button You cancontinue setting desired washing procedures After setting push down the start pause button The child lock functionis activated allof the buttons are locked andcannot make selection e Release the childlock function pushdown water levelbutton and spin button at the same time for more 2seconds After a beep sound the child lock function isreleased A POWER button Push the POWER button to switch on the power Under power on mode push it to switch off the power Push the POWER button to switch on the power If the START PAUSE button is not pushed the machine will switch off the power automatically after 5 minutes B START PAUSE button e After the poweris switched on press it
4. the leg the adjustable leg 2 After adjustment fasten the nut Usage the drain hose The drainage shall be smooth with the drain hose 1 The height of the drain hose shall be less than 10cm or the drainage will not be smooth and 4 lf extra drain hose is needed please make cost such long time that the machine may stop separate purchase The inner diameter of the at mid way extra hose shall not less than 30mm and the length shall not exceed 1 5m 2 Do not step on or press the drain hose 3 If the drain hose is too long cut it at mid point 5 If the extra hose is too long cut it either at A Tomake smooth drainage cut the front end of or atB the hose slantingly I gt om How to change the direction of the drain hose 5 Use the operation button Description of i button POWER Fuzzy m 6 ON OFF i i A R 20h 7 8 COMMON STANDARD 1 Lean the machine down gently with the front 4 Put your hand into the machine and loosen the a a 30 Sme aan ueuone surface facing the ground as indicated in Figure 1 clip of drain pipe support then pull inside the pipe THRORNSE Oe 20 5 3 4 om a ae and fetch out from the other side and set it on the 88 3 12 seco sik PAUSE A 2 Dismantle the rear cover of the washing machine clip as indicated in Figure 3 manne ie t WATER Progam as indicated in Figure 2 5 Install Hook of fixing the drain hose and bottom F z 9 3 Pinch the mouth of drain pipe and take off
5. topull the plugo newer receptacle Ensure that the earthing and close thewater faucet infollowing cases Please first pull off the power plug from the receptacle before cleaning prong of the power receptacle is earthed power failure deliveringthe machine setting the reliably Use leakage protector if possible machine idle orcleaning the machine Do not plug or pull the power plug withwet hand Clean the detergent box and set it on The lint filter must be used during washing the control panel seat t must be cleaned in time after each using 1 The method of dismantle Push it up aslant and gently Lint filter 2 The method of install install it upwards and aslant 1 Push down the spring piece of the top lint filter and push it in to make the claws out of the filter cover and then pull out the lint filter to get itdown figure1 2 Pull the back of the lint filter and then you can get down it off the front cover of the lint filter figure2 3 Sweep the rubbish in the lint filter 4 Put the back of the lint filter into the front cover raw 5 Put the lint filter into filter cover and make it SS Do not bend extend twist bind by force Do not press or nip it with weight Keep the pin of the power plug clean if the power plug is polluted with dust please wipe with dry cloth carefully f the power cord or the power plug is bad to avoid risk it is required to have it replaced by the technicians
6. Specification table Water level Water quantity about 1 23L 2 32L 3 40L 4 49L 5 58L 6 66L 7 76L 8 86L Water Injection pressure 0 03MPa 1 0MPa Washing spinning capacity 10 0kg 10 0kg Full Automatic Washing Machine User s manual This manual is for HWM100 828A WARRANTY Please read this manual Two years free for motor carefully before using One year free for other parts Retain it for future reference 0030508582A CONTENTS Names of the parts dos ROO WON see sar aS bie vee cce dor ors sse Safety precautions Installation and adjustment ese sos soe soo ooo sos soo ooo Install the water inlet hose ses coo sso soo ooo soo ooo ooo Preparation before washing ese ses oso ooo soo soo oso ooo ooo Usage of the detergent eee sse see soe soo soe cee coe coe seo Use the operation Dutton ce see see see see see see see seo Disposal after washing ese ese soe see soo see soo see oeo Trouble shooting answer to questions se e Packing list seo oco oco oos coo ooo oco coo soo soo oso soo coo coo oso Specification table 10 10 10 11 14 15 16 17 the back cover Packing list Name Quantity Storage position User s manual One Inside the document bag Components of the water inlet hose Inside the accessory bag Bottom Between the upper cushion of the washing machine package and the uppe
7. able foot label Meaning and description of the symbols Warning sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents Common phenomena Phenomena The spinning is intermittent when it starts Explanation Balance the laundries to avoid slanting The wash procedure is paused The cloth sensor is checking the cloth it willadd waterafter 48 seconds Push the PROGRAM button to select SPIN but it doesn t work The program is setting the drain time Some time is needed before it starts spinning The pulsator pauses during water inlet in wash and rinse Itis to avoid splashing during water inlet There may be some water flowing out of the drain hose in the first use of the machine Itis the water remained in the factory inspection of performance 16 Forbidden sign Contents marked with that symbol are actions forbidden to perform Performing of those action may result in damage of the machine or influence the personal safety of the users Safety precautions Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Please plug the power plug on special mne a Werte 98 positionen Somat Otherwise it may influence your using the machine receptacle Be sure to use three pins e plug Is accessible Be sure
8. allation the threading is 2mm above the upper surface of the nut See to figure 6 It is not recommended to use rich foam washing powder Washing powder with poor quality or long time storage may get caked Please clean the detergent box duly in usage About 4mm before twisting About less than 2mm after twisting 4 Close the top lid As the top lid opened the washer will automatically given alarm and stop running exclusively during draining Figure 4 Figure 6 10 if Connection between the water inlet hose and the washer inlet hose 1 Do not take off the water absorption cushion Please check if the cushion is dropped or damaged before each usage If it happens nut of ne water please contact our after sale department immediately Q A gt jointer of the water absorption water inlet valve cushion 2 Put the nut of the water inlet hose on the valve jointer 3 Fasten the nut Swing it gently to confirm if it s suitable 1 Push down the slider Insert the water inlet hose into the jointer the joi i e jointer of the 2 water inlet hose 2 Hang the lock lever to the jointer Release the slider till a click sound is heard Check the connection between the jointer of the water inlet hose and the water faucet 1 Swing the hose gently to confirm if it is fastened stable 2 After installation open the faucet to check if it leaks 3 Do not bend the hose with overstrain 4 Bef
9. be texture and volume of the laundry The washing cycle is automatically controlled 13 D WASH button Press the Wash button toselect a washtime from the MEMORY BLANKET CHILD SPEEDY STANDARD programs Press the Wash button can select or cancelthe process ofwash but cannot change time from the SILK programs e The button isunavailable from the SPEEDY and WOOL programs E SPIN button e Press the SPIN button to selectspin time fromthe MEMORY BLANKET JEAN STANDARD program The button isunavailable from the SPEEDY and WOOL programs Press SPIN buttoncan select orcancel the processof spin butcan not change time from the SILK programs F WATER LEVEL button Common memory and standardprocedures for washing machineautomatically detects the amountof cloth the water level isautomatically set to 4 6 8in an appropriate level Into the wet clothing may be set to 8 level the user needs tochoose the appropriate level Due to differentlevels of wet anddry cloth to determinethe actual water levelmay be different Washing machines beganto work to manuallychange the level pressthe start pause buttonre select If there s water inside the tub the machine cannot detect the laundries and will display water level 6 During the period of washing and rinse holddown the water buttonfill water handrelease or overflow water to stop when reachedthe water level Wool silk programlevel only
10. nding outer tub cover shaft groove Please install to designated position to guarantee there are no dropping or abnormal sound in opening and closing of the inner cover and the operation shall be smooth Do not dismount the inner cover component after washing Q Outer tub cover Outer tub cover shaft groove Right hand Inner cover shaft Left hand Inner cover component Figure 1 Figure 2 Install the bottom plate After you open the package please lean the washing machine gently down on soft items like the towel cloth blanket etc Install the bottom plate to the bottom of the machine then lift the machine up gently See to the figure Soft items Bottom plate Section enlarging Two claws at the bottom cover shall be inserted in two bar shaped holes in the stand Make sure the claws are firmly in place DELAY button Press the DELAY button digital display the time of washing appointment by the hour display LED starts blinking In hours an appointment can choose between 2 24 hours for a long time press by DELAY button the time of appointment can be continuously increased Appointment process press the DELAY button to display reservation status J SOAK button For the MEMORY BLANKET JCHILD STANDARD programs push th SOAK botton to select the desired soak time 10 20 30 40 minutes The button isunavailable from the SPEEDY SILK andWOOL programs It displa
11. of our special shop or our customer care agent gt tight Ay 6 Make sure the lint filter well installed or it can Dismantle In case the washing machine is installed on ground with Do not use water hotter than 50 C carpet do not block the ventilation hole with carpet influence your use The ventilation holes at the bottom Carpet 9S Do not put the machine at damp place like Do not wash water proof laundries like the bathroom Never wash it with water Do the raincoat bike covers etc to avoid not put wet laundries on the control panel abnormal vibrations in spinning Install Figure 1 Figure 2 The filter screen of the water inlet valve is likely to be Ae oo blocked by foreign materials and influence the water If the cabinet is dirty wipe it with wet cloth inlet Do not flush it directly with water Please clean it with brush every two months Wipe it with neutral detergent e Do not wipe it with thinner petrol alcohol etc Do not let the machine share one receptacle with other f electric appliances If the plugging into the receptacle 2 Do not store water in the washing machine for a long period Drain the water completely after each using is loose do not use the plug any more 3 Be sure to pull off the power plug before maintenance fe OS 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open
12. ore each usage please check if the connection between the jointer of the water inlet hose and the water faucet and the installation of the water inlet hose are firm so as to prevent dropping from improper installation position Dismantle the water inlet hose 1 Close the water faucet 2 Press the locking lever Push down the slider Then pull of the water inlet hose If the machine is used frequently the jointer of the water inlet hose can be kept on the faucet to prevent damaging the fixing screw 1 Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Pay attention to followings before washing the laundries Confirm if there s special requirement for the laundries Clear the pocket Take out the coins sand hairpins etc Fasten the buttons and zippers The quantity of the laundries shall not exceed the rated When the pulsator is running the buttons of the laundries may cause value The big noise For the sake of laundries like the discretion please put jeans shall be put the laundries with in loosely buttons into other laundries T
13. ot Detergent box applicable for fuzzy and reserve program 1 Add some water select 1 water level 2 Add washing powder Run for about 30s to fully dissolve the Powder Then push the START PAUSE button 3 Put in laundries Select suitable water level Push the How to use whitener START PAUSE Button again Quick dissolving of washing powder 1 Prepare warm water of 30 C and container 2 Add washing powder while stirring to dissolve it completely Slider Screw knife SF i 7 Bushing water inlet hose Figure 1 Figure 2 Figure 3 F 3 Fasten the four screws evenly See to Figure 4 Add water to stipulated level Dilute the whitener with container and then pour it into the liquid whitener inlet slowly Laundries with color or pattern is not colorfast thus not applicable 4 Take off the nameplate Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet See to Figure 5 Please add suitable washing powder as per the laundries quantity the set water level and water quantity if you select Speedy program it is suggested to use liquid detergent instead of washing powder to guarantee the washing effect The whitener shall not touch laundries directly See to the manual of whitener for the usage and dosage For whitener in powder dissolve it before use remark Before installation the threading is 4mmabove the upper surface of the nut After inst
14. per position during please take out all of the coins buttons sand hairpin washing If the lint filter is lost or Install PENTA and other foreign materials before washing damaged please contact the customer z care agent of our company tt Q A After finishing wash it ll alarm and switch off power automatically 14 Please check if the water faucet is open and if the connection of the water inlet pipe is proper Itis suggested to use foamless washing powder Tochange the direction of drain pipe please contact the customer care agent of our company Please dont use the washer in the environment below 0 if the washer has been stored below 0 please be sure to ensure the washer is placed under the room temperature for 24 hours and then use otherwise the washing effects may be lowered or the washer may be damaged Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the inner cover component 1 Open the top lid of the washing machine 2 Put the inner cover component on the outer tub cover aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove 3 Firstly insert the inner cover shaft of one side into the corresponding outer tub cover shaft groove then push the another inner cover shaft into the correspo
15. r seal of the package carton Full Automatic washing machine 17 Trouble shooting answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair Do not repair it by yourself Phenomena The reason How to settle The digitron displays E0 The top lid is opened during reserve procedure Close the top lid The drainage cannot work or is too slow The digitron displays E1 Is the drain hose put down Is the drain hose blocked Put down the drain hose Open and close the top lid once Clean the foreign material Open and close The top Lid Once It stops running in midway The digitron displays E2 The top lid is not closed Close the top lid The safety switch acts and the spinning cannot work The digitron displays E3 Are the laundries put slantingly Is the machine slanting Reorder the laundries Close the top lid Th machine will start running after 10 seconds of being placed horizontally The water filling does not work the digital displays E4 s the water tap opened or is there water supply failure Is the water inlet valve blocked Is the water pressure too low Open the water tap Push the start Pause button once Clean the water inlet valve then push the Start Pause button once Push
16. rinkage occurs the laundry and do not touch Jb lb Ss Stretch the laundry toits original the laundry Reshape the Z ZN size and locate itwith pins Use laundry As illustrated a steam iron todry the laundry in Fig 1 Figure 1 completely Donot touch the laundry Asillustrated in Fig 2 LR Figure 2 3 Push SOAK WASH RINSE SPIN button to select suitable procedure program Even there s no water in the tub a certain period is required before spin starting Separate the laundries that are not colorfast from other laundries in washing The soak procedure can work in cooperation with automatic programs like MEMORY BLANKET SANDARD CHILD COMMON There is intermittent pulsator stirring during soak After the machine starts operation you can only set the program and procedure during washing and soaking During rinsing you can only set the spinning time and can not make setting in other cases During speedy and tub dry programs push the wash rinse spin button the machine have no reaction Safety precautions Do not put hand into the rotating tub It is dangerous even if the rotation speed is slow Take special care of the children Keep children away from the washing machine to avoid them climbing on Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wa
17. sh laundries with volatile materials such as thinner petrol etc 4 Push the WATER LEVEL button select suitable water level For program the washing machine will execute fuzzy program automatically to detect the cloth After defection it can set the water level automatically To select other water level first push the START PAUSE button then push the WATER LEVEL button to set the water level 5 Push the DELAY button to select suitable reserve wash program After switching on the power the reserve program is set to off mode automatically If you need to set the washing procedure to be finished at reserved time please push the DELAY button to set the reserve wash program Refer to reserve button in Page 12 for selection When the DELAY function is activated the indicator light of the program you A gt have set will be off The reserve hour and time remain indicator lights will be on During reserve procedure push the DELAY button to display the reserve mode To change the running program or cancel the reserve setting you need to switch off the power and make new selection 6 Push the START PAUSE button 6 Finish washing The handicapped or children without care shall not use Keep the machine away from direct sunlight and the machine heat source like the heater Please keep the lint filter in good condition To protect your laundries and washing machine and install it to pro
18. the Start Pause button once The digitron displays E6 The water level sensor is bad Please contact the after sales service department The machine does Not wash not act s there power failure Is the power plug inserted tightly Is the water level reached preset position Please use it when there s power supply Insert the power plug tightly Fill water to the preset position Not spin Is the power plug inserted tightly Is the top lid closed reliably Are the laundries set flat Insert the power plug tightly Close the top lid Set the laundries flat There s abnormal sound inside the machine Is the machine slanting Are the laundries put slantingly in spinning Are there any foreign materials Adjust the machine to be even Reorder the laundries and close the top lid Remove the foreign materials The water tap leaks Is the screw of the jointer of water inlet hose loose or awry Fasten the screw of the jointer properly Names of the parts Top lid componen Inner cove Detergent bo Water absorption Screw cover gasket Water inlet valve pwer cord Control panel s P Cabinet handle Inner tu Hook Drain hose Pulsator Drain bushing Drain protective lid Back cover Cabinet Base fram Fixed foot 3 Adjust
19. the top lid for some time about 1 hour then close the top lid 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 15 The washing machine has a Wool program intended for high grade fabrics such as cashmere First make sure the laundry can be washed with water or not If not donot use the washing machine to wash the laundry If yes select the washing cycle recommended by the fabric man ufacturer The Woollen program can be used to wash fine clothes such as cashmere sweater linen blouse woolen pants For clothes with local stains such as sticky stains at collar or cuff lay the clothes upon a towel and spread neutral detergent for washing machine on the stains Use a soft brush to pat at the clothes gently before putting the clothes into the machine Do not rub the clothes hard Before washing please fold up the laundry as needed then put the laundry into the inner tub flat and neat These fabrics are not washable 1 Fabrics that deform when soaked in water 2 Fabrics that shrink discolor or go through other exterior changes when soaked in water 3 Fabrics that lose original texture when soaked in water 4 Fabrics that discolor when soaked in water 5 Fabrics that have pilling or pressed pile when soaked in water 6 Fabrics that have damage when soaked in water Upon completion of washing iron the laundry with a steam iron Hold the steam iron above w When sh
20. tostart the machine e During working push it to pause e During pause pushthis button torestart and goon working C PROGRAM button Program Application Program Application COMMON Washing the common laundries STANDARD Standard saving washing for normal laundries The commom wash the washing machine BLANKET Washing the relatively big and thick laundries MEMORY will set to MEMORY program including wash rinse spin water value automatically last time JEAN Washing the relatively big and thick laundries Washing for the woollen laundries under 2 5kg SPEEDY Quick washing for normal laundries Washing the silk laundries Put in the laundries Install the water inlet hose Confirm the water faucet The capacity of washing of the machine refer to the largest weight of the standard laundries under dry condition that can be washed in one time Laundries quantity in one washing cycle shall be lower than Water faucet suitable Water faucet not suitable the standard capacity The thickness size type of the cloth will influence the actual washing capacity It is suitable to put in reasonable amount of laundries and the laundries can be turned Outlet end surface round in washing for one time washing Do not select 4 water level for laundries less than 1 0kg so as to avoid splashing of water It is required that the front end shall be longer than 10mm How to use the softner The exit end face of the fa
21. ucet shall be flat and smooth If not please file it to avoid leakage The usage and dose of the softener as per the specifications of softener 3 Usage of detergent Before washing put the softener into the detergent box directly as mee inthe lert figure eee eles Connection between the water inlet hose jointer and the water faucet Control panel seat when the last rinsing After that please close the detergent box Refer to the following list for the usage of the detergent selection of the water level water quantity and dosage of detergent After the softener is put in please don t place for a long time otherwise C softener may solidify and cause flowing not smooth s Liquid detergent inlet 1 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 2 Loosen the screw till the water faucet can be accessed Put the jointer of the water inlet hose on the faucet See to Figure 2 If the faucet is too large and the jointer can not be set on the water faucet please loosen the four screws and take out the bushing in the jointer The front end of the faucet must be smooth otherwise it may leak water See to Figure 3 How to use washing powder r water inlet hose jointer Itis suggested to add washing powder into the box directly under fuzzy program and reserve program Dissolve directly inside the washing machine n
22. ys during detecting t displays remained reserve time hour It displays abnormal symbol in abnormal situation See to Page16 L RESERVE WATER button You can choose RESERVE WATER function to keep the after rinsing water Washing machine will keep the after rinsing water once finish rinsing in tub about 4 hours and buzzer every 15 minutes For example if you choose SECOND RINSE the machine only keep the after second rinsing water if you choose FIRST RINSE and SECOND RINSE together the machine will keep the after first and second WATER rinsing water Press START PAUSE button or open and close the top lid one time to collect the after rinsing water then the machine will go on for next program If you don t collect the after rinsing water within 4 hours the machine will drain automaticly then go on for next program Steps of using the operation buttons and description of the steps 1 Push POWER button to switch on the power 2 Push PROGRAM button to select suitable full auto program After the power is switched on MEMORY is automatically set To select other full auto program please push the PROGRAM button till the corresponding indicator is on Refer to the PROGRAM button on Page 10 E g Set to SPEEDY program for small quantity of laundries with light soil When a standard cycle is selected the fuzzy program is run The water level and the washing time can be selected according to
Download Pdf Manuals
Related Search