Hafler 200 User's Manual
Contents
1. Hafler MODEL 200 LOUDSPEAKER SYSTEM HAFLER A DIVISION OF ROCKFORD CORPORATION TEMPE ARIZONA ACKNOWLEDGEMENT Your new HAFLER Model 200 Loudspeakers were designed and manufactured to achieve a high level of sonic performance We are confident that the Model 200 Loudspeakers will serve you well as the final link in your audio system If you have any questions or comments feel free to contact our facilities GENERAL INFORMATION The HAFLER Model 200 Loudspeaker systems are equipped with removable cloth grilles To remove the grille assemblies gently pull out one corner and slowly work off the other three corners To replace the grille assemblies align the nylon male female fasteners and gently tap on each corner With the grilles removed you will notice that the Model 200 Loudspeakers operate as a mirror imaged pair Correct positioning places the high frequency driver which is on the same side as the HAFLER logos to the outside relative to the listening area Proper configuration is critical for optimum sonic performance A purchase registration card has been included with your Model 200 Loudspeakers Please complete the card and return it to our facilities The Model 200 Loudspeakers are covered under a five year limited warranty HAFLER recommends that all packaging be kept for future use The carton is easily flattened by slitting the tape on both ends It can then be re taped for transporting the speake2. clearly marked denoting plus as red and minus as black Maintaining the plus minus convention throughout your system will ensure proper performance As a quick check reverse the polarity of one speaker and listen to the result The type of wire you use is entirely up to you However we do recommend that you use the minimum lengths of wire required for your installation Generally heavier wire lower gauge numbers reduces the potential for signal losses The input terminal is located towards the bottom of the rear panel Binding post terminals are utilized which can accomodate a variety of connectors banana type plug spade terminal pin terminal or bare wire A tight connection will ensure reliable operation PLACEMENT The HAFLER Model 200 Loudspeakers are compact and lend themselves to a number of installations Proper placement within your listening environment may greatly enhance your listening experience Since each application is unique we encourage you to experiment with where you place your speakers keeping the following guidelines in mind Distance between two loudspeakers affects stereo imaging If the loudspeakers are brought closer together the sound stage will become narrower Increasing the distance between two loudspeakers may create a hole within the soundstage Pointing them inward relative to the listening area may help imaging for speakers placed very far apart For a well defined soundstage we recommend
3. that the speakers be placed six to eight feet Low frequency output can be adjusted by boundary proximity Moving a speaker closer to a boundary enhances the bass output For optimum sonic performance we recommend the use of optional stands with the Model 200 Loudspeakers Placing the stands with the speakers two to three feet from the rear boundary will produce a well balanced soundfield The Model 200 Loudspeakers are compact enough to fit onto a book shelf or entertainment center In these applications the speakers should be placed at least four to six inches from the rear boundary This distance is critical for proper vent port operation Utilizing the PORT PLUG in this application may be desirable to balance the low frequency output Feel free to experiment CARE The hardwood cabinets are finished with Watco Danish Oil which penetrates and hardens the wood Periodic maintenance and cleaning will add longevity to your speakers finish We recommend wiping down the enitre cabinet with lemon oil and buffing with a soft clean cloth Furniture polish containing waxes is not recommended Accumulated dust may be removed from the grille assembly by using a feather duster gently and sparingly You may want to remove the grille from the speaker before dusting The drive units in your Model 200 Loudspeaker system are very delicate devices If they become dusty gently go over them with a feather duster It is important not to damag
4. e or puncture the driver diaphragms SPECIFICATIONS FREQUENCY RANGE 50 Hz to 20 kHz SENSITIVITY 88 db SPL with 1 Watt at 1 meter IMPEDANCE 4 Ohms nominal POWER REQUIREMENTS 150 Watts channel maximum 20 Watts channel minimum DIMENSIONS 8 5 10 25 14 5 WEIGHT 15 pounds each unpacked FINISH dark oak veneer with black cloth grille LIMITED WARRANTY The Hafler Loudspeaker system is warranted against defective materials or workmanship for a period of five years from the original date of purchase This warranty extends to the original purchaser and covers products purchased from an authorized HAFLER dealer only Proof of purchase must accompany all returned items Defective parts will be repaired or replaced within a reasonable amount of time without charge for labor or materials Warranty does not cover transportation costs to the repair site HAFLER will return the loudspeaker to the purchaser at HAFLER S expense when repair is covered by this warranty This warranty does not cover damage due to negligence misuse shipping damage or accident Except as provided herein HAFLER makes no warranties expressed or implied including warranties of merchantability and fitness for a particular purchase Some states do not permit limitation or exclusion of implied warranties therefore the aforesaid limitations or exclusions may not apply to the purchaser This warranty constitutes in its entirety HAFLER s obligation fo
5. r its product HAFLER in no way implies or supports warranties to extend or broaden the scope of this warranty which may be offered by independant dealers PLEASE DIRECT ALL INQUIRIES TO HAFLER A DIVISION OF ROCKFORD CORPORATION 613 South Rockford Drive Tempe Arizona 85281 800 366 1619 SI 9 12 89 CP 7250A MODEL 200 MODEL 200SPECIFICATIONS FREQUENCY RANGE SENSITIVITY IMPEDANCE POWER REQUIREMENTS DIMENSIONS FINISH REAR MOUNTED PORT 5 MIRROR IMAGE DRIVER ARRAY e SLOPING FRONT BAFFLE 6 OAK VENEER CABINET
6. rs PORT PLUG The PORT PLUG included with the Model 200 Loudspeaker systems is used to prevent the enclosure port tuning effect This may be desirable when matching the Model 200 Loudspeakers with additional low frequency systems subwoofers or loading them into corners see section on placement When using additional low frequency systems the Model 200 loudspeakers are not required to reproduce low frequencies and should be used with a high pass crossover Depending on the type of crossover and the crossover frequency the port output may still be present and contribute to the overall system response The PORT PLUG eliminates the tuned output and effectively seals the enclosure Therefore reducing the low frequency output and providing an air spring for the low frequency driver The air spring provides a back pressure to the woofer and reduces its motion which results in an increase in the ability to handle large low frequency transients Normally the Model 200 Loudspeakers should be used without the PORT PLUG Use the PORT PLUG when the above situations arise Although using the PORT PLUG in the normal mode of operation will not damage the Model 200 Loudspeakers the tonal balance will be affected WIRING Maintaining proper polarity when wiring the speakers is important Improper wiring will degrade the sonic performance of your audio system Low frequency output will be mostly affected due to phase cancellation The input terminal is
Download Pdf Manuals
Related Search