Graco 3A1333A User's Manual
Contents
1. the con trol box See FIG 1 3 Install the USB module using four screws 341 The fifth screw 343 and star washer 342 must be installed in the center knockout to provide a ground ing contact to the control box 343 Warnings Install the USB cable 345 through the side of the control box and secure with the bulkhead nut N included Connect the other end of the cable to the USB port on the module Install the bulkhead cover 346 over the USB cable port Place the warning label 347 above the USB cable port as shown in Fic 1 GND ee ii Oe pu me 341 A 7 ca A x 345 Fic 1 Install USB Module N ny m YU if mf ms un mn un u um ti16427a 3A1333A Warnings Install the Power CAN Cable Non IS Systems 1 Remove the user interface cable from J8 of the fluid control module and plug it into connector P3 of the USB module See FIG 2 2 Connect Part No 15V778 Cable order separately to J8 of the fluid control module and to connector P4 of the USB module 3 Close the Control Box Restore power 4 See your ProMix 2KE Operation manual for instruc tions on using the USB module USB Module T116580a T116579a Fic 2 Install Part No 15V778 Cable Non IS Systems IS Systems 1 Connect Part No 15V782 Cable order separately to J2 of the alternator module and to connector P3 of the USB module See FIG 3 2 Close t2. Instructions Parts G GRACO 24H253 USB Module Kit B To add a USB Module to a ProMix 2KE Electronic Proportioner For professional use only Important Safety Instructions Read all warnings and instructions in this manual and in your separate ProMix 2KE manuals Save these instructions Kit Parts Ref Part Description Qty 340 16F358 USB MODULE with TOKEN T 1 see manual 3A1244 for token instructions 341 121417 SCREW 342 102063 WASHER 343 195875 SCREW 345 24H084 USB HARNESS 346 15R325 COVER bulkhead 3474 15X214 LABEL warning lt a aaa A A Replacement Danger and Warning labels tags and cards are available at no cost NOTE You must order a CAN cable separately to com plete the installation e For systems approved for Hazardous locations IS alternator powered order Part No 15V782 Cable e For systems approved for non Hazardous locations non IS order Part No 15V778 Cable PROVEN QUALITY LEADING TECHNOLOGY Warnings Warnings The following warnings are for the setup use grounding maintenance and repair of this equipment The exclama tion point symbol alerts you to a general warning and the hazard symbols refer to procedure specific risks When these symbols appear in the body of this manual refer back to these Warnings Product specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable Flammable fumes suc
3. h as solvent and paint fumes in work area can ignite or explode To help prevent N FIRE AND EXPLOSION HAZARD Zt fire and explosion e Use equipment only in well ventilated area e Eliminate all ignition sources such as pilot lights cigarettes portable electric lamps and plastic drop cloths potential static arc e Keep work area free of debris including solvent rags and gasoline Do not plug or unplug power cords or turn power or light switches on or off when flammable fumes are present e Ground all equipment in the work area See Grounding instructions e Use only grounded hoses e Hold gun firmly to side of grounded pail when triggering into pail e If there is static sparking or you feel a shock stop operation immediately Do not use equipment until you identify and correct the problem e Keep a working fire extinguisher in the work area A ELECTRIC SHOCK HAZARD This equipment must be grounded Improper grounding setup or usage of the system can cause electric shock Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment e Connect only to grounded power source e All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations 2 3A1333A Install the USB Module A i 1 Disconnect main power Open the control box 2 Remove the five knockouts K on the top of
4. he Control Box Restore power 3 See your ProMix 2KE Operation manual for instruc tions on using the USB module To help prevent fire and explosion do not connect download or remove the USB flash drive unless the unit is removed from the hazardous explosive atmosphere location Never leave the USB flash drive in the USB port USB Module Alternator Module T115710a J2 Fic 3 Install Part No 15V782 Cable IS Systems 3A1333A Warnings 3A1333A 5 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of
5. non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warrant
6. out Graco products visit www graco com TO PLACE AN ORDER contact your Graco distributor or call to identify the nearest distributor Phone 612 623 6921 or Toll Free 1 800 328 0211 Fax 612 378 3505 All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Original instructions This manual contains English MM 3A1333 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 Copyright 2010 Graco Inc is registered to ISO 9001 www graco com
7. y must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s a la suite de ou en rapport directement ou indirectement avec les proc dures concern es Graco Information For the latest information ab
Download Pdf Manuals
Related Search