Graco 334014A User's Manual
Contents
1. accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within six 6 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY2. section may appear throughout the body of this manual where applicable MPa bar PSI 334014A FIRE AND EXPLOSION HAZARD Flammable fumes such as solvent and paint fumes in work area can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Eliminate all ignition sources such as pilot lights cigarettes portable electric lamps and plastic drop cloths potential static arc Keep work area free of debris including solvent rags and gasoline Do not plug or unplug power cords or turn power or light switches on or off when flammable fumes are present Ground all equipment in the work area See Grounding instructions Use only grounded hoses Hold gun firmly to side of grounded pail when triggering into pail Do not use pail liners unless they are antistatic or conductive Stop operation immediately if static sparking occurs or you feel a shock Do not use equipment until you identify and correct the problem Keep a working fire extinguisher in the work area Route exhaust away from all ignition sources If diaphragm ruptures fluid may be exhausted with air PRESSURIZED EQUIPMENT HAZARD Fluid from the equipment leaks or ruptured components can splash in the eyes or on skin and cause serious injury Follow the Pressure Relief Procedure when you stop spraying dispensing and before cleaning checking or servicing equipment Tighten all fluid connections before operati
3. AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim or breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other good sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en An lais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s la suite de ou en rapport directement ou indirectement avec les proc dures concern es Graco Information For the latest information about Graco products visit www graco com For patent information see www graco com patents To place an order contact your Graco D
4. Ipm Air Consumption Approximate Cycles per Minute 50 100 150 200 250 120 3 4 96 2 7 72 i 2 0 scfm Nm3 min 8 48 1 4 24 0 7 D 0 0 10 20 30 40 50 38 76 114 151 189 Fluid Flow gpm lpm 19 Technical Data Technical Data eran I a a Air pressure operating ange TT O76 aA bar Te pm IT cable meters per mins High Pressure Setting 1 4 cubic meters per minute TT GbR Hates per High Pressure Setting 2 7 cubic meters per minute 150 High Pressure Setting 174 Ipm Maximum pump speed Low Pressure Setting 280 cpm High Pressure Setting 225 cpm Maximum suction lift varies widely 16 ft dry 4 9 m dry based on ball seat selection and 29 ft wet 8 8 m wet wear operating speed material properties and other variables Maximum size pumpable solids 1 8 in Recommended cycle rate for continuous 93 140 cpm e in Low or High pressure setting c s systems in Low or High pressure setting Tin npt or 1 in beet Tin nt or 1 in bspt Weight 48 Ib aluminum manifolds 21 8 kg aluminum manifolds 60 Ib SST manifolds 27 2 kg SST manifolds u R 20 334014A Technical Data Low Pressure Setting High Pressure Setting Low Pressure Setting High Pressure Seting Low Pressure Setting High Pressure Seting Wetted parts aluminum plus the material s chosen for seat ball and diaphragm options Non wetted external parts aluminum coated carbon steel Fluid Temperature Range NOTICE
5. Operation i GRACO Husky 1050HP 2 1 1 inch high pressure pump with modular air valve for fluid transfer applications For professional use only Important Safety Instructions Read all warnings and instructions in this manual and in your Repair Parts manual Save these instructions Maximum Fluid Working Pressure 200 psi 1 38 MPa 13 8 bar Maximum Air Input Pressure 100 psi 0 69 MPa 6 9 bar ti23666a CE Brrcoencn PROVEN QUALITY LEADING TECHNOLOGY Contents Related Manuals 2 cececeeeeeeneeeeeeeeeeeeeeees 2 Ordering Information 0 cecceeeeeeeeneeeeeeaneeees 3 Configuration Number Matrix 4 Waning E o aaraa VE ER ae PE OAT 5 Installation c ccceeece cece eeeeeeeeeeceeeeaeeeeeeneeeaes 8 Tighten Fasteners Before Setup 5 8 MOUN ease a an chi TEE 8 Groun aeae ekee AEA NE EATARRA 8 AI LIN Giese cee ot a E n R TEANA 9 Air Exhaust Ventilation cceeeeeeees 10 Fluid Supply Line eeceeeeeeeeeeeeeeeees 11 Fluid Outlet Line cece EAE 11 Fluid Inlet and Outlet Ports 11 Typical Floor Mount Installation 12 Operation aae aea aaa enaar P a ra 13 Pressure Relief Procedure 13 Related Manuals Tighten Fasteners Before Setup 5 13 Flush the Pump Before First Use 13 High Low LOVEM c cceeeeeeeeeeeeeeeneeeeeeaaeeees 13 Start and Adjust the Pum
6. TECTIVE EQUIPMENT Wear appropriate protective equipment when in the work area to help prevent serious injury including eye injury hearing loss inhalation of toxic fumes and burns This protective equipment includes but is not limited to e Protective eyewear and hearing protection e Respirators protective clothing and gloves as recommended by the fluid and solvent manufacturer Installation Installation The Typical Floor Mount Installation page 12 is only a guide for selecting and installing system components Contact your Graco distributor for assistance in planning a system to suit your needs Tighten Fasteners Before Setup Before using the pump for the first time check and retorque all external fasteners Follow Torque Instructions page 16 After the first day of operation retorque the fasteners Mounting e The pump exhaust air may contain contaminants Ventilate to a remote area See Air Exhaust Ventilation page 10 Never move or lift a pump under pressure If dropped the fluid section may rupture Always follow the Pressure Relief Procedure page 13 before moving or lifting the pump 1 Be sure the mounting surface can support the weight of the pump hoses and accessories as well as the stress caused during operation 2 For all mountings be sure the pump is bolted directly to the mounting surface Mount the pump horizontally with the feet at the bottom of the pump Do not mount the pum
7. Temperature limits are based on mechanical stress only Certain chemicals will further limit the fluid operating temperature range Stay within the temperature range of the most restricted wetted component Operating at a fluid temperature that is too high or too low for the components of your pump may cause equipment damage Diaphragm Ball Material Fahrenheit Santoprene SP 40 to 180 F 40 to 82 C 334014A 21 Graco Standard Husky Pump Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of five years from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures
8. ation page 12 1 Install an air filter regulator C An air line filter removes harmful dirt and moisture from the compressed air supply Use the regulator and 334014A Installation gauge to control the fluid pressure The fluid stall pressure will be the same as the setting of the air regulator Locate a bleed type master air valve B close to the pump and use it to relieve trapped air Be sure the valve is easily accessible from the pump and located downstream from the regulator Trapped air can cause the pump to cycle unexpectedly which could result in serious injury from splashing Locate another master air valve E upstream from all air line accessories and use it to isolate them during cleaning and repair An adjustable inlet air valve or needle valve G my be installed for pump speed control Install a grounded flexible air hose A between the accessories and the 3 4 npt f pump air inlet D Use a minimum 5 8 in 16 mm ID air hose Installation Air Exhaust Ventilation 2 Install a grounded air exhaust hose U Connect the muffler T to the other end of the hose The minimum size for the air exhaust hose is 3 4 in 19 mm ID If a hose longer than 15 ft 4 57 m is required use a larger diameter hose Avoid The air exhaust port is 3 4 npt f Do not restrict the sharp bends or kinks in the hose air exhaust port Excessive exhaust restriction can cause erratic pump operation 3 Place a co
9. further ordering To Order Replacement Parts information as needed 2 Please call Graco Customer Service to order Please call your distributor 334014A 3 Configuration Number Matrix Configuration Number Matrix Check the identification plate ID for the 20 digit Configuration Number of your pump Use the following matrix to define the components of your pump ti24479a Sample Configuration Number 1050HP_ A01A Pump Model Center Section Manifolds Seats Balls Diaphragms Manifold and Air Valve O Rings Center Section and Air Valve ena Valve Manifolds Material 1050HP Aluminum A01A ill Aluminum standard ports npt Aluminum Aluminum standard ports bsp Stainless steel standard ports npt Stainless steel standard ports bsp Check Valve Seats Check Valve Balls Diaphragm Material Manifold O Rings 4 334014A Warnings Warnings The following warnings are for the setup use grounding maintenance and repair of this equipment The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure specific risks When these symbols appear in the body of this manual or on warning labels refer back to these Warnings Product specific hazard symbols and warnings not covered in this
10. istributor or call to identify the nearest distributor Phone 612 623 6921 or Toll Free 1 800 328 0211 Fax 612 378 3505 All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Original Instructions This manual contains English MM 334014 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC AND SUBSIDIARIES P O BOX 1441 MINNEAPOLIS MN 55440 1441 USA Copyright 2014 Graco Inc All Graco manufacturing locations are registered to ISO 9001 www graco com
11. luid being dispensed and the equipment wetted parts Flush the pump often enough to prevent the fluid you are pumping from drying or freezing in the pump and damaging it Use a compatible solvent Always flush the pump and relieve the pressure before storing it for any length of time 15 Maintenance Torque Instructions NOTE All fasteners for the fluid covers center diaphragm joint and manifolds have a thread locking adhesive patch applied to the threads If this patch is excessively worn the fasteners may loosen during operation Replace screws with new ones or apply medium strength blue Loctite or equivalent to the threads If fluid cover center diaphragm joint or manifold fasteners have been loosened it is important to torque them using the following procedure to improve sealing NOTE Always completely torque the fluid covers and center diaphragm joint before torquing the manifolds Start all fluid cover or center diaphragm joint screws a few turns Then turn down each screw just until head contacts cover Then turn each screw by 1 2 turn or less working in a crisscross pattern to specified torque Repeat for manifolds ti23671a Fluid Covers and Center Diaphragm Joint 16 Fluid cover center diaphragm joint and manifold fasteners 100 in lb 11 3 Nem Lubricate air valve fasteners prior to reassembly to prevent galling Retorque the air valve fasteners in a crisscross patter
12. n to specified torque Air valve fasteners 80 in lb 9 0 Nem 1 3 5 7 ti25009a Air Valve Fasteners 10 14 ti23672a Manifolds 334014A Dimensions and Mounting KEY mogw gt 7 G Aluminum 12 7 in 323 mm 14 4 in 366 mm 15 3 in 389 mm 10 9 in 277 mm 1 8 in 46 mm 10 8 in 274 mm 21 5 in 546 mm SST 11 8 in 300 mm 12 9 in 328 mm 13 7 in 348 mm 9 5 in 241 mm 1 1 in 28 mm 10 7 in 272 mm 20 6 in 523 mm NOTE All dimensions are approximate ti23673a 334014A Z rAaArzctil Dimensions and Mounting Aluminum and SST 6 2 in 157 mm 9 4 in 239 mm 15 6 in 396 mm 3 4 npt f Air Inlet 1 in npt f or 1 in bspt Fluid Inlet 2 for aluminum manifolds 1 for SST manifolds 1 in npt f or 1 in bspt Fluid Outlet 2 for aluminum manifolds 1 for SST manifolds 3 4 npt f Air Exhaust Port 12 3 in 312 42 mm 17 Performance Charts Performance Charts Low Pressure Setting Operating Air Pressure A PSI 100 psi 0 7 MPa 7 0 bar MPa bar B 70 psi 0 48 MPa 4 8 bar c 40 psi 0 28 MPa 2 8 bar D 20 psi 0 14 MPa 1 4 bar How to Read the Charts 1 Locate fluid flow rate along bottom of chart 2 Follow vertical line up to intersec
13. ng the equipment Check hoses tubes and couplings daily Replace worn or damaged parts immediately Warnings EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury Do not operate the unit when fatigued or under the influence of drugs or alcohol Do not exceed the maximum working pressure or temperature rating of the lowest rated system component See Technical Data in all equipment manuals MPa bar PSI Use fluids and solvents that are compatible with equipment wetted parts See Technical Data in all equipment manuals Read fluid and solvent manufacturer s warnings For complete information about your material request MSDS from distributor or retailer Do not leave the work area while equipment is energized or under pressure Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use Check equipment daily Repair or replace worn or damaged parts immediately with genuine manufacturer s replacement parts only Do not alter or modify equipment Alterations or modifications may void agency approvals and create safety hazards Make sure all equipment is rated and approved for the environment in which you are using it Use equipment only for its intended purpose Call your distributor for information Route hoses and cables away from traffic areas sharp edges moving parts and hot surfaces Do not kink or over bend hoses or use hoses to pull equipment Keep children and animals away f
14. ntainer at the end of the air exhaust line to catch fluid in case a diaphragm ruptures To provide a remote exhaust If the diaphragm ruptures the fluid being pumped 1 Remove the muffler T from the pump air MID Aaus Wi Geel exhaust port re d A ti23675a Figure 2 Vent exhaust air KEY A Air supply line G Optional needle valve for pump speed adjustment B Bleed type master air valve T Muffler C Air filter regulator U Grounded air exhaust hose D Air inlet V Container for remote air exhaust E Master air valve for accessories 10 334014A Fluid Supply Line See Typical Floor Mount Installation page 12 1 Use grounded flexible fluid supply hoses G See Grounding page 8 2 Ifthe inlet fluid pressure to the pump is more than 25 of the outlet working pressure the ball check valves will not close fast enough resulting in inefficient pump operation 3 Excessive inlet fluid pressure also will shorten diaphragm life Approximately 3 5 psi 0 02 0 03 MPa 0 21 0 34 bar should be adequate for most materials 4 For maximum suction lift wet and dry see Technical Data page 20 For best results always install the pump as close as possible to the material source 334014A Installation Fluid Outlet Line See Typical Floor Mount In
15. p eeeeee 14 Pump Shutdown 2 ceceeeeeeeeeeeeeeeeeeees 14 Maintenance cceeeeeeeeeeeeeeeeeeaeeeeeeeaaeeeeeaaeeeees 15 Maintenance Schedule s 15 Lubricationses5 cc c c bsgtiek chisveundeiceines leu 15 Tighten Threaded Connections 0 00 15 Flushing and Storage a e 15 Torque Instructions 2 ceeeeeeeeeeeeeee ees 16 Dimensions and Mounting eceeseeeeeeeeeeees 17 Performance Chatts cceeeeeeeeeeeeeeeeeeeaaeees 18 Technical Dataiscisesecsssisssatticlsccsthaetsuctegescheaets ahd 20 Fluid Temperature Range 21 Graco Standard Husky Pump Warranty 22 Maman foes SSCS 334390 Husky 1050HP Air Operated Diaphragm Pump Repair Parts NOTE For Troubleshooting information see the Repair Parts Manual 334390 334014A Ordering Information Ordering Information To Find Your Nearest Distributor Distributor Note 1 Visit www graco com 1 To find part numbers for replacement parts 2 Click on Where to Buy and use the Distributor a Use the 20 digit number from the ID plate Locator on the pump b Use the Configuration Number Matrix on the To Specify the Configuration of a New next page to understand which parts are Pump described by each digit c Use the Repair Parts Manual Refer to the Please call your distributor main Parts illustration and to the Parts Kits Quick Reference Follow the page references on these two pages for
16. p on a vertical surface such as a wall 3 For ease of operation and service mount the pump so air valve air inlet fluid inlet and fluid outlet ports are easily accessible Grounding The equipment must be grounded to reduce the risk of static sparking Static sparking can cause fumes to ignite or explode Grounding provides an escape wire for the electric current Pump Loosen the grounding screw GS Insert one end of a 12 ga minimum ground wire R behind the grounding screw and tighten the screw securely Connect the clamp end of the ground wire to a true earth ground A ground wire and clamp Part 238909 is available from Graco R ti23674a Figure 1 Grounding Screws and Wires 334014A Air and fluid hoses Use only grounded hoses with a maximum of 500 ft 150 m combined hose length to ensure grounding continuity Air compressor Follow manufacturer s recommendations Fluid supply container Follow your local code Solvent pails used when flushing Follow your local code Use only conductive metal pails placed on a grounded surface Do not place the pail on a nonconductive surface such as paper or cardboard which interrupts the grounding continuity Check your system electrical continuity after the initial installation and then set up a regular schedule for checking continuity to be sure proper grounding is maintained Air Line See Typical Floor Mount Install
17. rom work area Comply with all applicable safety regulations THERMAL EXPANSION HAZARD Fluids subjected to heat in confined spaces including hoses can create a rapid rise in pressure due to the thermal expansion Over pressurization can result in equipment rupture and serious e Open a valve to relieve the fluid expansion during heating e Replace hoses proactively at regular intervals based on your operating conditions PLASTIC PARTS CLEANING SOLVENT HAZARD Many solvents can degrade plastic parts and cause them to fail which could cause serious injury or property damage e Use only compatible water based solvents to clean plastic structural or pressure containing parts e See Technical Data in this and all other equipment instruction manuals Read fluid and solvent manufacturer s MSDSs and recommendations 6 334014A 334014A Warnings TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin inhaled or swallowed e Read MSDSs to know the specific hazards of the fluids you are using e Route exhaust away from work area If diaphragm ruptures fluid may be exhausted into the air e Store hazardous fluid in approved containers and dispose of it according to applicable guidelines BURN HAZARD Equipment surfaces and fluid that s heated can become very hot during operation To avoid severe burns Do not touch hot fluid or equipment PERSONAL PRO
18. stallation page 12 1 Use grounded flexible fluid hoses L See Grounding page 8 2 Install a fluid drain valve J near the fluid outlet Install a shutoff valve K in the fluid outlet line Fluid Inlet and Outlet Ports NOTE Remove and reverse the manifold s to change the orientation of inlet or outlet port s Follow Torque Instructions page 16 1050HP Aluminum Manifolds The fluid inlet and outlet manifolds each have two 1 in npt f or bspt threaded ports M N Close off the unused port using the supplied plugs 1050HP Stainless Steel Manifolds The fluid inlet and outlet manifolds each have one 1 in npt f or bspt port 17 Installation Typical Floor Mount Installation ti23667a Figure 3 Typical floor mount installation KEY A Air supply line B Bleed type master air valve required for pump C Air filter and regulator D Air inlet E Master air valve for accessories F Flexible fluid suction hose G Optional needle valve for pump speed adjustment 12 Fluid drain valve required Fluid shutoff valve Flexible fluid outlet hose Fluid inlet 2 ports on aluminum manifolds 1 port on SST manifolds Fluid outlet 2 ports on aluminum manifolds 1 port on SST manifolds Ground wire required see Grounding page 8 334014A Operation Pressure Relief Procedure MPa bar PSI Follow the Pressure Relief Procedure whenever you see this symbol This eq
19. the pump long enough to thoroughly clean the pump and hoses Close the dispensing valve if used Close the bleed type master air valve Pump Shutdown MPa bar PSI At the end of the work shift and before you check adjust clean or repair the system follow the Pressure Relief Procedure page 13 334014A Maintenance Maintenance Schedule Establish a preventive maintenance schedule based on the pump s service history Scheduled maintenance is especially important to prevent spills or leakage due to diaphragm failure Lubrication The pump is lubricated at the factory It is designed to require no further lubrication for the life of the pump An inline lubricator is not needed and is not recommended under normal operating conditions Tighten Threaded Connections Before each use check all hoses for wear or damage and replace as necessary Check to be sure all threaded connections are tight and leak free Check fasteners Tighten or retorque as necessary Although pump use varies a general guideline is to retorque fasteners every two months See Torque Instructions page 16 334014A Maintenance Flushing and Storage MPa bar PSI e Flush before fluid can dry in the equipment at the end of the day before storing and before repairing equipment e Flush at the lowest pressure possible Check connectors for leaks and tighten as necessary e Flush with a fluid that is compatible with the f
20. tion with selected operating air pressure curve 3 Follow left to scale to read fluid outlet pressure top chart or air consumption scfm bottom chart Nm min 18 Fluid Pressure Approximate Cycles per Minute 56 112 168 224 280 100 0 70 7 0 80 0 55 5 5 60 0 41 4 1 40 0 28 2 8 20 0 14 1 4 0 0 10 20 30 40 50 38 76 114 151 189 Fluid Flow gpm lpm Air Consumption Approximate Cycles per Minute 56 112 168 224 280 75 2 1 60 1 7 45 1 3 30 08 B 15 0 4 0 0 10 20 30 40 50 38 76 114 151 189 Fluid Flow gpm lpm 334014A High Pressure Setting Operating Air Pressure A 100 psi 0 7 MPa 7 0 bar B 70 psi 0 48 MPa 4 8 bar C 40 psi 0 28 MPa 2 8 bar D 20 psi 0 14 MPa 1 4 bar How to Read the Charts 1 Locate fluid flow rate along bottom of chart 2 Follow vertical line up to intersection with selected operating air pressure curve 3 Follow left to scale to read fluid outlet pressure top chart or air consumption bottom chart 334014A Performance Charts Fluid Pressure Approximate Cycles per Minute 50 100 150 200 250 200 1 38 13 8 160 1 10 11 0 120 0 83 8 3 Psi A MPa bar 30 0 55 5 5 B 40 C 0 28 2 8 D 0 0 10 20 30 40 50 38 76 114 151 189 Fluid Flow gpm
21. tlet pressure and inlet air consumption NOTE The lever must be fully seated into the High or Low position for proper operation 13 Operation Start and Adjust the Pump 1 14 Be sure the pump is properly grounded Refer to Grounding page 8 Ensure the High Low pressure lever is in the Low position before starting the pump Check all fittings to be sure they are tight Use a compatible liquid thread sealant on all male threads Tighten fluid inlet and outlet fittings securely Place the suction tube if used in the fluid to be pumped NOTE If fluid inlet pressure to the pump is more than 25 of outlet working pressure the ball check valves will not close fast enough resulting in inefficient pump operation NOTICE Excessive fluid inlet pressure can reduce diaphragm life and may result in pump damage Place the end of the fluid hose into an appropriate container Close the fluid drain valve Turn the air regulator knob to 0 Open all bleed type master air valves If the fluid hose has a dispensing device hold it open 9 10 11 12 Slowly increase air pressure with the air regulator until the pump starts to cycle Allow the pump to cycle slowly until all air is pushed out of the lines and the pump is primed NOTE Use lowest possible air pressure to prime just enough to cycle the pump If the pump does not prime as expected turn air pressure DOWN If you are flushing run
22. uipment stays pressurized until pressure is relieved manually To help prevent serious injury from pressurized fluid such as splashing in the eyes or on skin follow the Pressure Relief Procedure when you stop pumping and before you clean check or service the equipment 1 Shut off the air supply to the pump 2 Open the dispensing valve if used Shift the high low pressure lever back and forth two times Leave the lever in the Low position as shown ti23687a Figure 4 High Low Pressure Lever 334014A Operation 4 Open the fluid drain valve installed on the system to relieve all fluid pressure Have a container ready to catch the drainage Tighten Fasteners Before Setup Before using the pump for the first time check and retorque all external fasteners Follow Torque Instructions page 16 After the first day of operation retorque the fasteners Flush the Pump Before First Use The pump was tested in water If water could contaminate the fluid you are pumping flush the pump thoroughly with a compatible solvent See Flushing and Storage page 15 High Low Lever Use the High Low lever to set the desired pressure mode When the lever is set to Low the fluid outlet pressure is slightly less than the air inlet pressure When the lever is set to High the fluid outlet pressure is slightly less than two times the inlet air pressure Note that the High pressure setting increases both fluid ou
Download Pdf Manuals
Related Search