Goldline GVA-24 User's Manual
Contents
1. WO O N 0 12 o clock 3 o clock 12 o clock 3 o clock 6 o clock 6 o clock WIM gt NM Two Port Valve The Model GVA 24 Actuator may be mounted to the valve in four different positions In all cases the cam settings are the same Refer to the chart below for cam settings for 2 way valves 9 o clock 12 o clock CAM SETTING LOWER CAM 3 o clock UPPER CAM 6 o clock aja N eaj NIWIWIN Mounting Instructions If the valve is plumbed with Port 2 as the common port and the main body of the actuator is mounted over Port 2 standard mounting there is no need to adjust the actuator cams l Remove Locking Knob and handle Set aside for reinstallation later 2 Remove four 4 screws from the valve Refer to Fig 1 mounting positions to determine which screws to remove 3 On the back side of the actuator align the smallest slot on the actuator shaft with the smallest slot on the valve diverter 4 With the two shafts engaged rotate the actuator until holes on the actuator align with the screw holes on the cover 5 Use four 4 14x1 2 long screws packaged with the actuator to secure it in place Do not overtighten be careful if using a power screwdriver 6 Place valve handle on actuator shaft and tighten Locking Knob Cam Adjustment 1 When changing the cam settings move toggle switch at bottom of actuator to the OFF center position 2 Unscrew and r2. eUCIssejoud peyijenb e Buiney puswwose Alyy 9M NOILNALLY PSAOWA SI 19409 OU USYM JOJEN Oe y UO Burom JBASUSYM uone BS pe O UUODSIP JO yo ynys usaq Troubleshooting If you believe your actuator is not operating properly or have questions regarding the operation call the Goldline Technical Service Dept from Monday through Friday 8AM to 8PM EST at 888 921 7665 Aunful ul ynses ACW SUONONIYSU MOJO o anje Buimoyjo au VINYAHLYAdAH JO S194443 Bulpnjoul pamoyjo 9q sAemje pinoys suoneoad Ajajes oIseq jUsLUCINbsS jeaoa Siy Buisn uayM 1 Actuator handle oscillates This condition may happen when the GVA 24 O ring seals are not lubricated suffi ciently See Maintenance section in this manual gt lt m j L m 2 m atr A C O Q O Z 5 J a S v3 Z Z O 1 gt oO Cc n D O 9 S Q e gt Q Q Q a fe om 3 oO Q O fab O a O fab Q Q oO te a lt O r D o n oO o y oO N n z O o Sa o a ay lt To oO om iy y D 3 5 2 Actuator motor works but the valve diverter does not turn On a pool spa combination the symptom of this problem would be a draining or overflowing spa This condition will occur ifthe actuator is in the manual position To correct this pull up on the handle while rotating the handle in any direction until it clicks then tighten the Locking Knob SNOILONULSNI T
3. E WARRANTY OF GOLDLINE WITH RESPECT TO ITS POOL AUTOMA TION AND CHLORINATION PRODUCTS AND IS IN LIEU OF ALL OTHER WAR RANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN NO EVENT SHALL GOLDLINE BE RESPONSIBLE FOR ANY CONSEQUENTIAL SPECIAL OR INCIDENTAL DAM AGES OF ANY NATURE WHATSOEVER INCLUDING BUT NOT LIMITED TO PERSONAL INJURY PROPERTY DAMAGE DAMAGE TO OR LOSS OF EQUIP MENT LOST PROFITS OR REVENUE COSTS OF RENTING REPLACEMENTS AND OTHER ADDITIONAL EXPENSES EVEN IF THE SELLER HAD BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM AGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU NO WHOLESALER AGENT DEALER CONTRACTOR OR OTHER PERSON IS AUTHORIZED TO GIVE ANY WARRANTY ON BEHALF OF GOLDLINE THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN ALTERED IN ANY WAY AFTER LEAVING THE FACTORY Copyright 2008 Goldine Controls 092051B GOLDLING VALVE ACTUATOR Installation Manual for model GVA 24 G LD LINE www goldlinecontrols com SSS 888 921 7665 Maintenance The GVA 24 has two seals which should be lubricated every year These O ring seals are located at the top and bottom of the actuator where the shaft exits the actuator housing The top
4. IV MOT104 GNV AVA SNOILONALSNIALSAVS LNVLYOdINI 3 Actuator motor does not turn The motor will not turn if the switch is in the OFF position or if there is no power to the actuator If the switch is in the OFF position move to ON1 or ON2 To check power to the actuator measure AC volts between the black common and each switch leg red then white If there is no AC volts on either leg check the 24VAC power source Jo JoBuep y ul Bunjnses sssusnolosuooun pue fqn joy JO eds y 1x 0 Aqiqeul jeois yd uswoM zueub d ul eaGewep jeje psezey Bulpusdul Jo ssauesemeun fqn oy JO eds 1X9 0 peau y z u ov 0 nj ez e y AlBOJEd 0 SINE spNjoul elueuedAy Jo s josyse ey Hunuley pue ss uismoup ABiJeuls Sseulzzip Apoq ay Jo nyes dw JEUJOJU OY Ul BSesJOUI Ue PEpnjoul elLUSyWEdAy Jo SWO dWAS SU 40996 JO Inzeszadw Apog jewou y sAoge s p eJenes aAe e Seyoess Apog y Jo sinyesedws JeUJO UI y UBYM SJND9O eIWWeyEdAH sey Jojenjoe y 0 Ajddns samod y ss jun 4 A00 JOJeN Oe y Spisul zu s d sue SEHeYOA MoT INOILNVD 7 5 The toggle switch on the bottom of the valve actuator can be used to verify if the new adjustment is correct flip between ON1 and ON2 6 Replace cover and handle and tighten screws and Locking Knob 7 Put toggle switch back to ON1 or ON2 position Synchronization Instruction After installation of the actuator s they may need to b
5. LIMITED WARRANTY Goldline warrants its Aqua Rite Aqua Rite Pro Aqua Trol Aqua Logic and Pro Logic products products with Goldline part numbers starting with AQ RITE AQ RT PRO AQ TROL AQ LOGIC AQL P AQL PS AQL CL PL P PL PS and HPC 2 to be free from defects in material or workmanship under normal use and service For three years from the date of the initial system installation on private residential swimming pools within the USA or Canada and one year from the date of initial system installation on commercial installations installations outside of the USA or Canada and for any replacement parts or accessory products provided they are installed in accordance with the Goldline installation instructions and specifications provided with the product If written proof of the date of the initial system installation is not provided to Goldline the manufacturing datecode on the Aqua Rite Aqua Rite Pro Aqua Trol Aqua Logic and Pro Logic electronics unit will be the sole determinant of the date of the initial system installa tion For residential installations in USA or Canada If a product is defective in workmanship or materials and is removed and returned freight prepaid within three 3 years after the date of the initial system installation Goldline will at its option either repair or replace the defective product and return it freight prepaid For commercial installations installations outside the USA and Canada and acces
6. O ring requires the removal of the handle and the bottom requires that the gear train is disengaged Follow the procedure below for instructions on how to lubricate the O ring seals Before performing this procedure turn off pool filtration s po jeoujoa 9 jqe jdde e YM soueldwood ul jauuos d p enb Aq paljeysul q ISNW pZ YA9 epoyy Sul PjOD L 1 Put the toggle switch in the OFF center position JOMOd O1ND98 9 o un BulosUUOdeJ 91049q SJOAOD pue SMAJIS e 2ejd y Pun HuUIDIAJES B1OJEq JAMO edIN NE 9 JOOULODSIG Z 2 Remove the actuator from the valve Remove the Locking Knob and handle 3 Spread a small amount of Jacks 327 or other silicone based lubricant around the actuator shaft where it enters the cover souuly e e pasiAsedns Ajasojo aie Ady ss jun yONpoud siy sn o u pj yo ywad zou op Anfu JO ysu y SONPSs OL ONINYVM 4 Reinstall handle and Locking Knob but only tighten one 1 turn 5 Push down on the Locking Knob to disengage the gear train This will allow the handle and the shaft to be moved in any position 6 Spread a small amount of lubricant around the actuator shaft where it protrudes from the bottom of the actuator enclosure 7 Turn the handle once around to spread the lubricant 8 Pull up on the handle let it click into place and tighten Locking Knob AUeLIEM INOA pioa JO pue Anfu jeuosiad 319498 Ul NSO pinos os op O SuNjle4 JONpoud siy e SuI
7. e synchronized Out of syn chronization refers to the condition where one actuator is rotating incorrectly in relation to another actuator To correct this simply flip the toggle switch at the bottom of the actuator which is out of synchronization between the ON1 and ON2 position Manual Override In the event of a power failure you may need to move the valve position manually Before performing this procedure turn off pool filtration just in case power resumes Follow the instructions below for manual override of the GVA 24 actuator 1 Put the toggle switch in the OFF center position 2 Unscrew the Locking Knob above the handle approximately 4 full turns Fig 3 3 Push down on the Locking Knob This will disengage the gear train and allow the handle and thus the diverter to be moved in any position 4 Toreturn the actuator to automatic position pull up on the handle while turning it clockwise or counterclockwise until you feel the shaft slide up into the gear train Screw the Locking Knob down until snug 5 Put the toggle switch back in the ON1 or ON2 position Locking Knob 4X Fig 3 Description The GVA 24 Goldline Valve Actuator rotates 2 port and 3 port valves automatically Use it with the Aqua Logic system or GL 235 Solar Controller to automate pool spa operation solar heating cleaner operation water features or a variety of other uses The industry standard conf
8. emove Locking Knob and handle from actuator shaft 3 Remove the four 4 screws which hold the actuator cover on and remove cover 4 The upper and lower cam are located on the actuator shaft Slide the cams off the shaft splines and rotate to the desired position Refer to the charts on the previous pages to determine the correct cam setting for your installation Some installations may require settings not found on the chart partial open partial close etc All settings are referenced from the small slot on the shaft which is always 12 o clock Fig 2 The upper cam effects the clockwise position stop point The lower cam to effects the counterclockwise rotation stop point 12 o clock r small slot 9 o clock 3 o clock
9. iguration of the GVA 24 means that it is compatible with all major manufacturer s valves and pool automation systems The unique cam setting feature ensures a quick and easy installation with the precise control of water flow Installation Mounting Options Three Port Valve The Model GVA 24 Actuator may be mounted to the valve in four different positions Fig 1 Depending on the location of the common port where water enters valve and exit port where water leaves valve the cam settings may have to be changed See diagrams tables on the following pages to determine which configuration matches your system A Standard B Port 2 Je g C D Fig Using the chart below to determine correct cam setting using standard clock posi tions Refer to the Cam Adjustment section in this manual to change upper and lower cam positions if necessary GVA MOUNTING OPTION PORT WHERE WATER ENTERS CAM SETTING LOWER CAM UPPER CAM PORT WHERE WATER EXITS PORT PORT A Standard a es std 12 o clock 12o clock 1 3 Soclock o clock 1 2 v 9 o clock 12 o clock N 6 o clock 9 o clock 2 3 Nh 3 o clock So clock 1 3 wo i 6 o clock 3 o clock 9 o clock 9 o clock 6 o clock 9 o clock NO
10. sory products and replacement parts If a product is defective in workmanship or materials and is removed and returned freight prepaid within one 1 year after the date of the initial system installation Goldline will at its option either repair or replace the defective product and return it freight prepaid Contact any Goldline dealer or contact Goldline at 61 Whitecap Drive North Kingstown RI 02852 for warranty service The costs incurred in removal and or reinstallation of the product are NOT covered under this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you WARRANTY EXCLUSIONS Material supplied or workmanship performed by others in process of installation Damage resulting from improper installation including installation on pools larger than the product rating Problems resulting from failure to operate the product s in accordance with the recommended instructions contained in product s owners manual s Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in the owners manual s Problems resulting from tampering accident abuse negligence unauthorized repairs or alternations fire flood lightning freezing external water degradation of natural stone used in or immediately adjacent to a pool or spa war or acts of God DISCLAIMER THE EXPRESS LIMITED WARRANTY ABOVE CONSTITUTES THE ENTIR
Download Pdf Manuals
Related Search