Global Machinery Company LDP13B12 User's Manual
Contents
1. easier 4 Tighten the handle screw firmly to secure the handle in position 5 Lift the handle up and then proceed with the drilling operation 5 To select a slower drill speed 6 To disable the depth lock move the belt down to a loosen the handle screw and h smaller step on the front and rotate the depth scale to the maximum depth central pulleys and a higher step on the central and rear pulleys Rotating the pulleys and rolling the belt onto the larger pulley will make this easier 7 Tighten the handle screw firmly to secure the handle in position Changing the speed 6 To tighten the belts on Caution Always ensure that the drill press is switched the pulleys pull the motor off and the plug is removed from the power point before backwards This is best done making any adjustments by grabbing hold of the top The speed of the drill press is determined by the size of the of the rear pulley and the pulley steps that the belt is attached to Using a smaller bottom of the motor housing pulley step on the front pulley means a faster drill speed 7 Rotate the pulley by hand to using a larger pulley step on the front pulley means a ensure everything is aligned PI i slower drill speed The below table indicates the speed of and correct the drill in the various belt positions 8 Replace the pulley cover Turning on and off 1 To start the drill press insert the switch disabling insert and move t2. it will go making any adjustments 3 Tighten the chuck by rotating the collar in an anti 1 The extension tables are handy when working with larger clockwise direction work pieces and allow the table size to be increased for greater material support 4 To remove the bit loosen the chuck by rotating the collar in a clockwise direction Setting the drilling depth Caution Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments 1 Loosen the handle screw half a turn using 6mm hex key 2 Ensuring the drill bit is tight in the chuck use the feed 2 To adjust the extension table loosen the 2 knobs on the wheel to lower the spindle underside of the work table until the drill bit just touches 3 Extend the extension table to the desired width the work piece 4 Tighten the 2 knobs to secure the extension table in position 12 3 Holding the handle in that position rotate the depth 1 Remove the plug from the mains socket scale to the desired drilling depth 2 Take off the pulley cover 3 Loosen the motor and reduce the belt tension by pulling the belt tension lever towards the motor and pushing motor forwards 4 To select a faster drill speed move the belt up to a higher step on the front and central pulleys and lower step on the central and rear pulleys Rotating the pulleys and rolling the belt onto the larger pulley will make this
3. power lt 1Mw Speed ranges Safety rules for laser lights The laser light laser radiation used in the GMC REDEYE system is Class 1 with maximum 1mW power and 650nm wavelengths These lasers do not normally present an optical hazard although staring at the beam may cause flash blindness Warning Do not stare directly at the laser beam A hazard may exist if you deliberately stare into the beam please observe all safety rules as follows e The laser shall be used and maintained in accordance with the manufacturer s instructions Never aim the beam at any person or an object other than the work piece e The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person for longer than 0 25s e Always ensure the laser beam is aimed at a sturdy work piece without reflective surfaces 1 e wood or rough coated surfaces are acceptable Bright shiny reflective sheet steel or the like is not suitable for laser use as the reflective surface could direct the beam back at the operator e Do not change the laser light assembly with a different type Repairs must only be carned out by the laser manufacturer or an authorised agent Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Please refer to the relevant Australian standards AS 2397 and AS NZS2211 for more infor
4. table of all objects tools scraps of wood etc Before starting the operation jog the motor switch to make sure the drill bit does not wobble or vibrate Let the spindle reach full speed before starting to drill If your drill press makes an unfamiliar noise or if it vibrated excessively stop immediately turn the drill press off and unplug it Do not restart until the problem is corrected Do not perform layout assembly or setup work on the table while the drill press is in operation Do not exceed the rpm stated on the bit or accessory See the instructions that come with the accessory When drilling large diameter holes clamp the workpiece firmly to the table Otherwise the bit may grab and spin the workpiece at high speed Do not use fly cutters or multiple part cutters as they can come apart or become unbalanced in use Make sure the spindle has come to a complete stop before touching the workpiece To avoid injury from accidental starting always tum the switch off and unplug the drill press before installing or removing any accessory attachment or making any adjustment Caution Do not expose to rain or use in damp locations Warning For your own safety read instruction manual before operating drill press Wear eye protection do not wear gloves necktie or loose clothing clamp workpiece or brace against column to prevent rotation use recommended speed for drill accessory and workpiece material Unpacking
5. table handle to the worm dnve shaft and tighten the grub screw using the 4mm hex key 10 16 Fit the table lock into the table support assembly and tighten to secure the table 17 Fit the depth scale lock onto the handle 18 Fit the handle and depth scale onto the motor head ensuring that the flats on the handle locate the flats on the shaft 19 Secure the handle onto the motor head by placing the handle bolt through the middle of the handle and secure it with the 6mm hex key 20 Fit the chuck onto the spindle and secure it by pushing it and giving it a sharp tap Note Ensure both surfaces are clean before putting the chuck on the spindle 21 Place a screwdnver through the top of the pulley cover loosen and remove the screw secunng the pulley cover Lift off the cover 22 Fit the belts over the pulleys refer to the inside of the cover for speed reference Note Fit the lower belt on first Note When fitting belts it is easier to place the belt onto the small pulley and then turn it onto the larger pulley 23 To tighten the belts on the pulleys pull the motor backwards This is best done by grabbing hold of the top of the rear pulley and the bottom of the motor housing 24 To loosen the motor and reduce the belt tension pull the belt tension lever towards the motor and push motor forwards 25 Replace and secure the pulley cover Adjustments Adjusting the table height
6. tool 1f the switch does not turn the tool on and off correctly Guard against electric shock Prevent body contact with grounded objects such as water pipes radiators cookers and refrigerator enclosures Use only approved parts When servicing use only identical replacement parts Use an authorised service facility to fit replacement parts Additional safety rules for drill presses Warning For your own safety do not try to use your drill press or plug it in until it is completely assembled and installed according to the instructions and until you have read and understood the following 1 N U1 8 9 Your drill press must be bolted securely to a workbench In addition if there is any tendency for your drill press to move during certain operations bolt the workbench to the floor This drill press is intended for use in dry conditions and indoor use only Always wear safety goggles which comply to a recognised standard Use a face or dust mask along with safety goggles 1f the drilling operation 1s dusty Use ear protectors especially during extended periods of operation Do not try to drill material too small to be securely held Do not drill material that does not have a flat surface unless it is clamped securely Always keep hands out of the path of the drill bit Avoid awkward hand positions where a sudden slip could cause your hand to move into the drill bit Do not install or use any dril
7. Caution Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments 1 Loosen the table lock 2 Rotate the handle in a clockwise direction to raise the table 3 Rotate the handle in an anti clockwise direction to lower the table 4 Tighten the table lock to secure the table Adjusting the table angle Caution Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments 1 Loosen the screw under the table by rotating it in an Tool storage drawer anti clockwise direction The tool storage drawer is handy for storing hex keys drill 2 Tilt the table to the desired angle as indicated on the bits and accessories dba cae Installing and removing drill bits Caution Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments 1 Loosen the chuck sufficiently so that the jaws are open wide enough to allow a bit to be inserted The chuck is loosened by rotating the collar in a clockwise direction 3 Tighten the screw under the table by rotating it in a clockwise direction Note When the table is tilted the work piece should be clamped to the table Extension tables Caution Always ensure that the drill press is switched off and the plug is removed from the power point before 2 Place the bit into the open chuck as far as
8. Due to modern mass production techniques it is unlikely that your GMC Power Tool is faulty or that a part is missing If you find anything wrong do not operate the tool until the parts have been replaced or the fault has been rectified Failure to do so could result in serious personal injury Required tools The following tools are required to assemble the drill press e 3mm 4mm 6mm Hex Keys Supplied e Wrench Not Supplied e Phillips Head Screwdnver Not Supplied Assembly time The LDP13B drill press will take approximately 20 minutes to assemble Accessories The LDP13B is supplied with the following components 1 Base No Column 3 Rack 4 Rack Collar 5 Table 6 Belts x2 7 Handle 8 Keyless Chuck 9 Extension Table Locking Knobs x4 10 Motor Head 11 Handle 12 Depth Scale 13 Table Lock 14 Worm 15 Hex Keys x3 16 Bolts for attaching column to base x4 17 Bolt to attach handle Know your product 1 Laser light on off switch 2 Laser aperture x2 3 On off switch 4 Pulley cover 5 Base 6 Column 7 Rack 8 Rack Collar 9 Table Support Assembly 10 Belts x2 11 Belt Tension Lever 12 Table Handle 13 Keyless Chuck 14 Extension Table Locking Knobs x4 15 Motor Head 16 Feed Handle 17 Depth Gauge 18 Depth Scale Lock 19 Table Lock 20 Bevel Scale 21 Hex Keys n F i Assembly 1 Place b
9. Zeno TIEN MANUAL REDEYE 1e HP 12 95peed Dril _ Press with Laser bine Generator EA E i CHINERY COMPANY A N e YEAR REPLACEMENT WARRANTY 30 SATISFACTION GUARANTEE Ne NENG NS Patent Pending e Melbourne Perth Auckland Hong Kong Shanghai L Ll P i B Taipei New York Verona London Paris 040614 ED3 JJ Contents Warranty Introduction Environmental protection Description of symbols Specifications Safety rules for laser lights General safety instructions Additional safety rules for drill presses Unpacking Required tools Assembly time Accessories Know your product Assembly Adjustments Adjusting the table height Adjusting the table angle Extension tables Tool storage drawer Installing and removing drill bits Setting the drilling depth Changing the speed Turning on and off Turning on the REDEYE laser line generator Adjusting the laser Operation Wood drilling Metal drilling Maintenance Cleaning General inspection Repairs Troubleshooting 9 CO NEN NE Sy NI BK GO UU UN Full 2 Years Home Use Warranty Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domest
10. anges may have occurred which render the product received slightly different to that shown in this instruction manual The manufacturer reserves the nght to change specifications without notice Note Specifications may differ from country to country 7 DAYS A WEEK 7AM 7 PM esr The GMC 777 Helpline operates from 7am to 7pm 7 days a week EST This allows you to contact GMC directly with any queries and technical questions you have regarding our products Save this Manual for future reference
11. ase on floor 2 Place column assembly on base and align the 4 holes in the column assembly with the holes in the base 3 Using the 4 8mm diameter x 20mm long bolts secure the column support to the base and tighten with a wrench 12 Fit the rack collar over the column and bring it down to the top of the rack Ensure the bevel side is down over the rack 13 Tighten the rack collar using the 4mm hex key To let the rack slide when the table is swung left or right around the column only tighten the set screw enough to keep the collar in place 14 Fit the motor head over the column and tighten the 2 grub screws using the 4mm hex key This will secure the head on the column 4 Loosen the screw on the rack collar using the 4mm hex key P 5 Remove the rack collar by lifting it up and over the column 6 Remove the rack from the column 7 Ensure that the 4 knobs securing the extension tables are tight 8 Fully insert the worm gear shaft into the table support and engage it on the gear wheel in the assembly 9 With the short smooth section of the rack pointing downwards slide the rack through the round opening in the table support 10 Engage the rack on the gear mechanism found inside the opening of the table support 11 Whilst holding the rack and table support slide both over the column Slide the rack down until the rack is positioned against the lower column support 15 Attach the
12. et superior performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service Caution Carefully read through this entire Instruction Manual before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection Recycle unwanted matenals instead of disposing of them as waste All tools hoses a 3 and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way Warnings It may be more difficult to see the laser line in conditions of bright sunshine and on certain surfaces Symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection Conforms to EMC regulations N380 Specifications Nominal voltage 230 240Vac 50Hz Power 375W Chuck capacity 13mm Chuck type Keyless Spindle axis to column distance 125mm Maximum spindle travel 60mm 230 330 370 460 530 580 1030 1160 1280 1600 1790 2470 RPM Laser class 1 Laser wavelength 650nm Laser output
13. he switch up to the ON position 2 Move the switch down to the OFF position to turn the drill press off 3 Remove the switch disabling insert to prevent unauthorised use and store it in a secure location out of reach of children Adjusting the laser 1 Clamp a scrap piece of material to the table 2 Insert a drill bit into the chuck jaws 3 Tum on the drill press 4 Using the feed wheel lower the spindle and make a small mark in the workpiece 5 Tum on the laser line generator 6 If the laser is not aligned with the mark in the work piece adjust as follows 7 Using the 3mm hex key loosen the set screw that secures the laser light assembly 8 Rotate the laser beam until it intersects the mark in the Turning on the REDEYE laser line generator 1 The REDEYE laser line generator emits two intense narrow beams of pure red light that intersect at the workpiece drilling point i 2 The intersection is clearly visible and will not be A REpEAL the process for the PHAR other side obscured by dust It improves operator drilling vision enables faster set up increases accuracy and improves safety 3 To tum the laser line on move Operation the switch to the T position Caution Always ensure that the drill press is switched off and the plug is removed from the power point before making any adjustments Caution For through drilling always ensure that the hole in the centre of the tab
14. ic use from the date of the onginal purchase If found to be defective in matenals or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the nght to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use It also does not cover any bonus accessones unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types of claim that are permissible and those that are not Dear Customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone our Help Line for an immediate response Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to me
15. l bit that exceeds 175mm 7 inches in length or extends more than 150mm 6 inches below the chuck jaws They can suddenly bend outwards or break Do not use wire wheels router bits shaper cutters circle fly cutters or rotary planers on this drill press When cutting a large piece of material make sure it is fully supported at the table height Do not perform any operation freehand Always hold the workpiece firmly against the table so it will not rock or twist Use clamps or a vise for unstable workpieces 10 Make sure there are no nails or foreign objects in the part of the workpiece to be drilled 11 Whenever possible position the workpiece to contact the left side of the column if it is too short or the table is tilted clamp solidly to the table 12 13 14 15 16 17 18 19 20 21 ZZ 23 24 25 If the workpiece overhangs the table such that it will fall or tip if not held clamp it to the table or provide auxiliary support Set the drill press to a speed appropnate to the job Do not start the drill press while the drill bit is touching the workpiece When using a drill press vise always fasten it to the table Make sure all clamps and locks are firmly tightened before drilling Securely lock the head and table support to the column and the table to the table support before operating your drill press Never turn your drill press on before clearing the
16. lace them if damaged Keep tool handles dry clean and free from oil and grease 13 Disconnect idle tools Switch off the power and disconnect the plug from the power point before servicing when changing accessones and when the tool 1s not in use 14 Remove adjusting keys and wrenches Check to see that keys and adjusting wrenches are removed from the tool before switching on 15 Avoid unintentional starting Always check that the switch is in the OFF position before plugging in the tool to the power supply Do not cary a plugged in tool with your finger on the switch 16 Use outdoor rated extension cords When a tool is used outdoors use only extension cords that are intended for outdoor use and are so marked 17 Stay alert Watch what you are doing Use common 18 19 20 sense Do not operate a power tool when you are tired Check for damaged parts Before using a tool check that there are no damaged parts If a part is slightly damaged carefully determine if it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts proper mounting and any other conditions that may affect the operation of the tool A part that is damaged should be properly repaired or replaced by an authorised service facility unless otherwise indicated in this Instruction Manual Defective switches must be replaced by an authorised service facility Do not use a
17. le is aligned with the drill bit Warning On start up over tightening the belts may prevent the drill press from starting Warning Don t force the drill allow the dnll bit to do the Work 4 To tum off the laser line move the switch to the 0 position 14 1 Adjust the table height table angle drilling depth and speed as required for the application 2 Insert the drill bit required for the application 3 Mark the drilling points on the work piece 4 Switch on the laser line and line up with the drilling point with the intersection point of the two beams 5 Where possible secure the workpiece 1n position with vice or clamps 6 Tum on the drill press using the on off switch 7 Rotate the feed wheel to bring the drill bit down to the workpiece 8 Apply pressure to the feed wheel and slowly drill through the workpiece Don t force the drill allow the drill bit to do the work 9 After drilling the hole release the feed wheel and allow the spindle to return to its onginal position 10 Turn off the drill press 11 Turn off the laser line generator Wood drilling e For maximum performance use high speed steel bits for wood drilling e Secure the workpiece to prevent it from tuming when drilling e When drilling through holes place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole Metal drilling e For maximum performance use high speed steel bit
18. mation on Lasers General safety instructions To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its potential hazards Children and infirm people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used It is also imperative that you observe the accident prevention regulations in force in your area The same applies for general rules of occupational health and safety Warning When using power tools basic safety precautions should always be taken to reduce the risk of fire electric shock and personal injury Also please read and heed the advice given in the additional important safety instructions 1 Keep the work area clean and tidy Cluttered work areas and benches invite accidents and injury 2 Consider the environment in which you are working Do not use power tools in damp or wet locations Keep the work area well lit Do not expose power tools to rain Do not use power tools in the presence of flammable liquids or gases 3 Keep visitors away from the work area All visitors and onlookers especially children and infirm persons should be kept well away from where you are working Do not let others in the vicinity make contact with the tool or extensi
19. on cord 4 Store tools safely When not in use tools should be locked up out of reach 5 Do not force the tool The tool will do the job better and safer working at the rate for which 1t was designed 6 Use the correct tool for the job Do not force small tools or attachments to do the job best handled by a heavier duty tool Never use a tool for a purpose for which 1t was not intended 7 Dress correctly Do not wear loose clothing or Jewellery They can be caught in moving parts Rubber gloves and non slip footwear are recommended when working outdoors If you have long hair wear a protective hair covering 8 Use safety accessories Safety glasses and earmuffs should always be worn A face or dust mask is also required if the sanding operation creates dust 9 Do not abuse the power cord Never pull the cord to disconnect the tool from the power point Keep the cord away from heat oil and sharp edges 10 Secure the work piece Use clamps or a vice to hold the work piece It is safer than using your hand and frees both hands to operate the tool 11 Do not overreach Keep your footing secure and balanced at all times 12 Look after your tools Keep tools sharp and clean for better and safer performance Follow the instructions regarding lubrication and accessory changes Inspect tool cords periodically and if damaged have them repaired by an authorised service facility Inspect extension cords periodically and rep
20. s for metal or steel drilling e Use a centre punch to mark the hole location on the workpiece e Maintain a speed and pressure which allows cutting without overheating the bit Applying too much pressure will e Overheat the dnl e Wear the bearings e Bend or burn bits e Produce off centre or irregular shaped holes e When drilling large holes in metal it is recommended to drill with a small bit at first then finish with a larger bit Also lubncate the bit with oil to improve drilling action and increase bit life Maintenance Warning Always ensure that the tool is switched off and the plug is removed from the power point before making and adjustments or maintenance procedures Cleaning 1 Keep the tool s air vents unclogged and clean at all times 2 Remove dust and dirt regularly Cleaning is best done with a soft brush or a rag 3 Re lubncate all moving parts at regular intervals 4 Never use caustic agents to clean plastic parts Caution Do not use cleaning agents to clean the plastic parts of the tool A mild detergent on a damp cloth is recommended General inspection Regularly check that all the fixing screws are tight They may vibrate loose over time Repairs Only an authonsed service centre should replace the cordset or effect other repairs If the cordset is damaged or worn have it repaired or replaced by an authonsed service centre Troubleshooting Warning Turn the on off switch to the off po
21. sition and unplug the tool from the power supply before performing trouble shooting procedures Troubleshooting Drill press will not start Power cord not plugged in Ensure that the cord is connected to the power supply Power fault fuse or circuit breaker tripped Check the power supply Cord damaged Use authorised service centre to repair or replace Faulty switch Use authorised service centre to repair or replace Faulty motor Use authorised service centre to repair or replace the motor Noisy operation Incorrect belt tension Adjust tension as required Drill bit burns Change speed refer to the Changing the speed section No packing material below workpiece Use packers below the workpiece 16 Carefully read the entire Instruction Manual before using this product Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 Australia or 0800 445 721 New Zealand When you make your call please have the following information at hand e GMC Product Type GMC Product Code A GMC Service Engineer will take your call and in most cases will be able to solve your problem over the phone You are welcome to use this phone in service to make suggestions or give comments about any GMC product GIL GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victona Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200 With continuing product development ch
Download Pdf Manuals
Related Search