Genie Garage Door Opener chainmax 1200 garage door opener User's Manual
Contents
1. 26 SE uuu pod NEUE EUR S Under 27 OPENER MUST BE INSTALLED WITH THE INCLUDED Safe T Beam SAFETY REVERSE SYSTEM MUST BE WALL CONSOLE INSTALLED TO CLOSE DOOR 4 2011 The Genie Company 3 2011 Begin here after the opener s physical assembly and installation has been completed There are no assembly or installation steps included in this manual Contact your Genie Professional Dealer for an installation poster if required or visit www geniecompany com to download a PDF file The following mechanical assembly tasks must be completed before continuing L Powerhead and rail are bolted to each other An illustration is shown on page 11 Example illustrations of the following items are shown on pages 12 and 13 O Rail end is attached to a header bracket which is attached to the garage door header L Powerhead is attached to a support frame suspended from the ceiling or ceiling joists L Both pieces of door arms are assembled and are attached to the garage door L Safe T Beam sensors installed and wired L Wall console installed and wired Shown on page 20 L Carriage is engaged to the chain drive An illustration is Shown on page 11 L Powerhead is plugged into an approved power outlet Begin programming by setting Limits see next page A PDF VERSION INSTALLATION POSTER IS AVAILABLE AT WWW GENIECOMPANY COM OR CALL 1 800 35 GENIE TO OBTAIN AN EMAIL PDF FILE IMPORTANT INSTALLATION INSTRUCTIONS2. 3 Table of Contents 4 Installation Important Installation Instructions 5 1 Programming Limits amp Force 6 7 Contact Reverse Iest 8 2 Program IntelliCode 2 Remote to Powerhead 9 Programming HomeLink Car2U IntelliCode9 1 remotes or wireless O 10 Reference 3 Typical Installed Illustrations 11 13 Powerhead amp Rail Assembled View 11 Typical Sectional Door Installation 12 Typical One Piece Door Installation 13 4 Overview of Powerhead Controls s 14 5 Overview of Remotes and Options 15 16 Lost or Stolen Remote Clearing Memory 15 di COGO Fr i ae Dane oies 16 Previously Installed Openers 16 6 Maintenance amp Troubleshoo
3. NEVER GO UNDER A STOPPED PARTIALLY OPEN DOOR Test opener monthly The door MUST reverse on contact with a 1 1 2 high object or a 2 x 4 board laid flat at the center of the doorway on the floor After adjusting either the force or the limit of travel retest the door opener Failure to adjust the opener properly may cause severe injury or death When possible use the emergency release only when the door is closed Use caution when using this release with the door open Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of severe injury or death KEEP DOORS PROPERLY BALANCED See your garage door Owner s Manual An improperly balanced door increases the risk of severe Ma or death Have a trained door system technician make repairs to cables spring assemblies and other hardw SAVE THESE INSTRUCTIONS 2011 The Genie Company 3 2011 17 WARNING Garage door hardware springs cables brackets pulleys etc are under extreme pressure and tension DO NOT attempt to repair or adjust door springs or any hardware and DO NOT OPERATE garage door automatically or manually if door is improperly balanced or springs are broken CONTACT A TRAINED DOOR SYSTEM TECHNICIAN ROUTINE MONTHLY MAINTENANCE Basic monthly maintenance tasks Safe T Beam System Check Door balance Contact reverse Instructions for these tasks and others are found on the following pages
4. CHAINMAX 1200 Model 4022 GARAGE DOOR OPENER OPERATION AND MAINTENANCE MANUAL Includes INTELLICODE 2 Remote Control Safe T Beam System must be installed to close door For use only with residential sectional or one piece overhead garage doors Homelink and Car2U compatible For Answers and Assistance 1 800 354 3643 or visit Www geniecompany com WARNING To reduce the risk of injury to persons or damage to property Use this opener only with a one piece or sectional door SAVE THIS MANUAL FOR FUTURE REFERENCE INSTALLER LEAVE THIS MANUAL WITH HOMEOWNER Genie Genie logo Intellicode Safe T Beam are registered trademarks of and ChainMax is a registered trademark of GMI Holdings Inc dba The Genie Company Homelink is a registered trademark of Johnson Controls Technology Company Car2U is a registered trademark of Lear Corporation O The Genie Company 2011 PN 37320500118 07 2011 SAFETY INFORMATION OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large heavy objects that move with the help of springs under high tension and electric motors Since moving objects springs under tension and electric motors can cause injuries your safety and the safety of others depend on you reading the information in this manual If you have questions or do not understand the information presented call your nearest trained door system technician or visit ou
5. Do NOT allow children to play with opener including wall console remote or wireless keypad During programming the door opener could begin to run so keep people and objects away from the moving door and its parts To keep the door from moving close the door and disconnect it from the rail carriage by pulling the Emergency Release Handle See page 19 for Release Handle operation Three Button Remote FlG 5 1 Remote See page 21 for battery changing instructions FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which may be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiver antenna Increase the separation between the opener
6. DOOR BALANCE SPRING TENSION With the door closed pull release handle DOWN and let go to release door carriage assembly from drive system Raise door manually approximately 3 A and release Door should remain stationary or move very slightly If door moves quickly CONTACT A TRAINED DOOR SYSTEM TECHNICIAN Close the door Verify RED block in carriage is in the up position refer to page 19 Operate door using remote or wall console Door will re attach itself to carriage assembly CONTACT REVERSE TEST Monthly test The Force and Limit settings MUST be COMPLETED before testing See pages 6 7 1 Test Open garage door using wall console Place a 2 x 4 board laid flat under center of garage door opening Fig 6 2 Close garage door using wall console When door contacts board the door must stop within 2 seconds and reverse direction returning to open position 2 Adjustment e f the door Stops before it contacts the 2 x 4 board it may simply be responding to an improperly set down limit Return to pages 6 7 and repeat steps 1 through 10 to correct down limit 18 2011 The Genie Company WARNING Use wall console supplied with opener Other approved wall consoles may be available Unapproved or incompatible wall consoles can cause the opener to operate unexpectedly Safe T Beam STB SYSTEM CHECK STB Red and Green LEDs ON steady system OK STB R
7. prior to removal or alteration of its condition Upon determination by Seller that the Product or any part thereof is defective during the applicable warranty period which may require purchaser to return the Product to Seller at purchaser s expense Seller will supply the purchaser with replacement parts or at its option a replacement Product shipping and handling of any replacement part s or replacement Product also at purchaser s expense Seller may use new or reconditioned parts or a new or reconditioned Product of the same or similar design There are no established informal dispute resolution procedures of the type described in the Magnuson Moss Warranty Act PURCHASER INSTALLATION ADDRESS DATE PURCHASED SERIAL NUMBER OPENER MODEL REMOTE CONTROL MODEL DEALER NAME DEALER ADDRESS P900 228
8. 18 OR Check garage door for binding Door will only open Check closing FORCE adjustment See page 23 Check Limits are properly set See pages 6 7 Door starts up but Be sure door opener and springs are in good repair properly lubricated and balanced STOPS before it is Check opening FORCE adjustment See page 23 completely open A WARNING If you suspect a problem with the garage door hardware or springs contact The Genie Company at 1 800 35 GENIE Check Limits are properly set See pages 6 7 e Check Sure Lock M Sure Lock should be OFF for normal operation See page 20 Door will only run Check door balance condition and door spring closed Check opening FORCE adjustment See page 23 A WARNING If you suspect a problem with the garage door hardware or springs contact The Genie Company at 1 800 35 GENIE e Button stuck on wall console or remote Door opener starts for gt oo Was a remote lost or stolen Erase all remotes from powerhead memory and program new remotes See page 15 24 2011 The Genie Company 3 2011 TR O U B L E S H OOTI N G G U I D E OPERATION CONTINUED 2 2 277 27 77 FOR HELP 1 800 35 GENIE PROBLEM WHAT TO DO Be sure all door fasteners are tight Noisy operation Be sure garage door is in good repair properly lubricated and balanced Be sure opener is in good repair Check operating condition of door See pages 18 Door may need professional repair
9. dais buiuuue4b04d q ee ussm sq 1noouJn puo2 s Qe e SI 3194 LU 2JOU se d Ne 2 lt NA SN EN k I s MOU OS Op Hered ou JS V313uU 03 pebebue ueeq LON Sey 3e Inq 31 3 LON san pue ssaud E mon pue ssaua 1 LIWI113AVH L HOOQ 15072 V JOOP 2 0 2 10 Uado o1 suoynq 10 au osn LON OG 195 ae 22004 pue SWI 92UQ 1994 9 UCU SSI SI SJILUI UIIMISA SDUP JSIP y JI MOJ S Je peeds JOOP S Je rneujoine Uh peouyiomod su sdajs asay Jo 21242 so u do jeu y buunp jas SI 22404 100 01 da1s uBnoiu1 enunuoo pue dais UM UIbag peouyiomod y jo woyoq y uo pe1e o jaued y buisn sqjueunsn pe bupjeu Aq pajo41u02 ase suomisod jur 100 NMOQ 3901 pue dN N3dO Saul 32404 UNV SLIWITDNILS3 L 8 ONILLAS 6L pue LL sabed 0 1939 10 pepiAo4d J 183s0d uonej e3suj ees syiuim 6un3es 340439 ebenae 03 pebebue eq 1SnW 3e Inq u L In250 ue Jeuedo y 0 eDeuiep 949595 jas 912 33H01 pU SLIWIT 940JoGQ OSUuO3 JEM ulO1J ZIUN Silu oje1edo ION OG f34edoud 0 abewep 10 Aunful pione 03 jdo d pue s 3e1sqo Jo 1eo pue MAIA UI sI BMIOOP dANs exyew papino4d ji 123504 uol p p sul Woy Guinurjuo DNINSVM W 32401 8 SLINIT DNIWWVSy5OJd L 3 2011 2011 The Genie Company OL L sdais jeada sbumss LIWII 19591 OL 3L1ON buruweiboid 3304134 y3IM 3NUIJUO Ud pue 1531 39943134 LIVLNOD InJSss 33ns e W10 124 j s SN3dO HOOQ 31SO15 400 35V3134 pue S
10. does NOT move Opener works from Check all remotes wall console but NOT Replace remote battery with good one See page 21 from remote Program remote to powerhead See pages 9 or 10 Relocate remote inside car and or point remote at garage door Remote has less than Replace battery See page 21 25 feet operating Reposition door opener antenna range or no operation Remote LED does not come ON with button push replace battery See page 21 Eliminate possible competing signals satellite radio FiOS TV Ifa NEW installation check Door Arm position Refer to Installation poster or download Door starts down poster from WWW GENIECOMPANY COM then STOPS and goes Check if Limits are properly set See pages 6 7 back up Check if Safe T Beam Red LED is flashing See page 18 Check Safe T Beam system for beam obstruction or misalignment of lenses See page 18 OR Check garage door for binding f an operational problem exists and opener will not close The opener can be forced to Safe T Beam System close as follows Press and hold the wall console button until door is completely closed malfunction Check for interference from adjacent Safe T Beam units Contact The Genie Company at 1 800 35 GENIE Door starts down Check Safe T Beam wire connections at powerhead See page 18 then STOPS before it CheckLimits are properly set See pages 6 7 is closed Check CONTACT REVERSE See page
11. of any other jurisdiction If transmitters are to be used in another country the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canad en la fecha de fabricaci n Ninguna garant a se da que cumplan con todas las reglamentaciones legales de ninguna otra jurisdicci n Si los transmisores se van a utilizar en otro pa s el importador debe determinar si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de los Estados Unidos y del Canad antes de usar los mismos Les metteurs sont conformes la r glementation am ricaine et canadienne compter de leur date de fabrication Aucune garantie n est stipul e indiquant qu ils sont conformes toutes les prescriptions juridiques d autres autorit s Si les metteurs sont utilis s dans d autres pays il incombe l importateur d en d terminer leur conformit aux lois et r gles locales pouvant diff rer de celles des tats Unis et du Canada avant toute utilisation desdits metteurs Sendeger te entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der Herstellung Wir bernehmen keine Gew hrleistung f r die Einhaltung aller gesetzlichen Bestimmungen in anderen L ndern Sollen Sendeger te in anderen L ndern eingesetzt werden
12. stops and reverses a closing door within two seconds of contact with an object Automatic ForceGuard Control Automatically sets the force required to fully open and close the door for maximum safety Watch Dog Monitoring System Monitors the Safe T Beam system to ensure proper functionality and will automatically stop and reverse a closing door if a problem is detected Manual Emergency Release Manually releases door from door opener Used during a power failure or other emergency to allow manual opening and closing of door SmartSet Electronic Programming Easily adjust the programming to reduce opening speed to a desired rate vary limits and force and program new remotes Automatic Lighting System Two bulb lighting system supplies up to 200 Watts of light for safer evening exits and entries Turns ON when door is activated and automatically turns OFF 4 minutes later Integrated Motion Detection Not available on all models Select units have motion detection built into the powerhead Lights automatically turn ON when motion is detected for much safer movement through the garage Lights will turn OFF after 4 minutes of no motion 2011 The Genie Company 3 2011 3 TABLE OF CONTENTS Section Page Safety Information 2 Opener Features amp Safety Features
13. 03 s pedAay sse aJIM 62PODIIISIUI D1UID Burwuuwub1bo1d podf sy ssa aJIm 40 aJOWAA sapo i a1u Ppe geue e e9po t o1u 9q 1snuu louu u 9 Bed aas o eu NO 2 oW91 UDIUM eJnsun ase NO J 930UJ9J uo uo1 nq 1ouJ 1 Z sepo 5r e13U s u D pouwueiBoid snoiA id e esee o4 pue SS3Hd dind use J _ sa31 4104 33S B ye 35V37134 pue ssiud 5 SOUS 62PODIIIOIUI 621U29 Suysel q31 jd nd 6uo 33S NS e SN lt ur SN qu TT d i IL j iu A p qeu e Z4p2 1 u o Aue 104 Jessadau se Jeaday 1591 9 3 2011 SUOHn2nJ1sul eNZAD AY MO OJ s J3IU A p qeu NZADI 104 aJd 19110 Aue 10J Jessadau se Jeaday 1S9L SIMI UONNQ exyuli auloH 941 SS3ud s buiuweibold ef 24D5 10 sXul aulOH NO 3UI0 gt NO Lo sq31enig 3 ne H104 335 E ouo JJS p E S T Q10H pue ssid 35V3134 ped e sse aJIM au YUM euJ02 IA pedAay sse aJI Z 49P0 1 93U 621099 104 OC Sais gyuljawoy U3IM enumnuoo Ua y sd 1s 1eedai pue suonponiulsu eXJui auioH buisn geXui aGuroH Jed BU YUM uogng jeu uJe150Jd ueu1 L eepo r e1u 01 Z eepo r e3u WOJ uonnq a3ouJaJ euo ebueup pue 9 obed 0 06 u u1 1ousdo e lu D 0 Daul u q Jah JOU seu eXur auloH ANOA J AO Q uon ses eyul uioH eui JO 9 pue deis ubnouu enunuoo pue da1s um uibeq Jausdo lu 5 ue o pouwelboid AjsnolAaid u q seu Julj uioH
14. 1 NOTE A maximum of 3 different openers can be programmed to a 3 button remote Three button remote Green LED Red LED 16 2011 The Genie Company Programming remote to previously installed IntelliCode 1 Genie garage door openers Remotes provided with this unit can operate other IntelliCode 1 models of Genie9 garage door openers The default IntelliCode 2 setting must be changed to IntelliCode 1 Follow these same steps to change IntelliCode 1 back to IntelliCode 2 The LED color displayed on the remote indicates the IntelliCode mode Red IntelliCode 1 Green IntelliCode 2 1 Select a button on the remote that has NOT been programmed to the new powerhead 2 Press and hold that button for 10 seconds Both Red and Green LEDs come ON and stay 10 SECS 3 Press the same button twice to toggle IntelliCode9 selection from IntelliCode 2 to IntelliCode 1 4 Press the same button again to confirm toggle The IntelliCode selection for this button is set to IntelliCode 1 5 Take the remote to the older Genie garage door opener and follow that opener s instructions to program a new remote Repeat for other Genie9 garage remote s as necessary 3 2011 TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture No warranty is made that they comply with all legal requirements
15. 1nof J burwwosbodd syuirj uioH suononuajsui Bulituuultei1Boid ped y eu ozu pouweiboid Apeauye Nid e pue pajjezsu ped y SS9 9JIM e lUu p INO aAey osje 1snuJ NOA pedAdy SS3 94IM eepo 5r o3u s u p 104 Ju s iud 910UJ9J L PONIJU s lu 5 INO sAey osje 1snui noA 930UuleJ s9po 5r o3u s u p 104 sdajs Hultuwesboid s u1 uuioJji d o1 suon nuasur Puruuej604d 11y pue 1u s id 2 DIU9A p Qeu eNZADD 10 eJjul uioH INO o eu osje 1snuu noA 62422 AO MUIDUUMOH 104 juesaJd pesylamod y 01 pauuelbold Apeauyje uong 3 0U19J Z 62PODIJIPIUI 621099 euo 1se Je ALY ISNW NO syse asau JO Aue duuo2 OL SdVdA3y SS3T3UIM L 92P0 1 934 pub SILOWIY L 92P0 1 1934 40 NZAV oy Ul aWwoH OL GVJHYIMOd DNINWVIDO A TYNOILdO o LA A Old b nd p ap ozbig 31 00 e op seig IDD O Jal Jap o4juap OPDIIQN ODD ap o1ualuDzi sa Wy 1004 IS Np Ana19JUI e anis 3oueup np aSSINO lei SpISUI po3e oJ aps e6enue 11 Jap o43uap ppp2iqn pu ppD2 184 np 1neug1uir e Ano as INb eujeu 1184 opisu po3e oJ ureu oz bd au jap o1Juap oppoiqn 10sua EIS Sie lt oz Bd rey np In luj lui e anis in pu eng SE Oz 6d j1e4 episui pa3e30 J3uoisu l OUD Jap o u luupzl s p ID DIV Duappo p au2upbu3 jonueup np assijnod e e a eq euieup e zeKe1quu3 opi S 96811185 0 Land urey ebebu3 UOIDD12Q ap D2uD Dd oBe INouSA9p ep soubliod 9 pueH se
16. A N 10XXXXEXXXXXXX A WU A Ifyou have another garage door opener that does NOT have a Serial Number like this then you will be using the INTELLICODE 1 setting on your remote to operate that opener INTELLICODE FEATURES Other models of Genie garage door openers remotes and wireless keypads use IntelliCode 1 signals to communicate Remote s provided with this unit will transmit either IntelliCode 1 or IntelliCode 2 signals Remote s contained in this package are preset to IntelliCode 2 and can be configured to communicate with previously installed IntelliCode 1 openers This dual IntelliCode9 option allows one IntelliCode 2 remote to operate different models of The Genie Company garage door openers This new Genie garage door opener will ONLY accept signals from a remote sending IntelliCode 2 signals see page 9 or a Genie9 brand IntelliCode 1 remote that has been programmed to the opener using a new IntelliCode 2 remote see page 10 NOTE Other remotes not enabled with Genie IntelliCode 2 will not operate this opener Use this IntelliCode programming One or more IntelliCode 2 Use IntelliCode openers with a maximum 3 2 different openers If you have Use IntelliCode Mixture of openers manufactured between 1997 2 and or 1 and 2010 IntelliCode 1 and new IntelliCode 2 openers One or more openers Use IntelliCode manufactured between 1997 1 and 2010 IntelliCode
17. CCIONAL 2011 The Genie Company 3 2011 13 4 OVERVIEW OF POWERHEAD CONTROLS This section describes the simple programming functions Use this page to familiarize yourself with the buttons and LED indicators used to program the opener NOTE These A and buttons are for programming use only Do NOT use these buttons to operate the opener ap MS Programming buttons location on powerhead FIG 4 1 Locate programming buttons There are three programming buttons and two lights LEDs on the powerhead To garage door ROUND LED Indicator Light PROGRAM BV Close Travel Button Facing Garage Door I FIG 4 2 Programming buttons Each of the buttons are used to enter and complete the setup programmino The LEDs indicate status or a function change by illuminating ON OFF or ON flashing in one of three different colors BLUE RED or PURPLE Throughout the instructions in this manual the buttons and LEDs are also displayed as icons Buttons Name LONG LED Indicator Light Shape Use PROGRAM Enters into and selects sr programming menus V multi function moves door advances through menus Jd Program button Close Travel button Open Travel button multi function moves door advances through menus LED Colors Round Red and l Long Red Round Purple and Long Purple Round Blue Q and D Long Blue 14 2011 The Genie Company Programming Overvi
18. E PORTE SECTIONELLE POUR OBTENIR DE L AIDE 1 800 35 GENIE INSTALACION HABITUAL DE UNA PUERTA SECCIONAL PARA OBTENER AYUDA LLAME AL 1 800 35 GENIE If required direct wiring of power supply to opener must be installed by a licensed electrician Power cord must reach grounded outlet without use of extension cord Le c blage direct de l alimentation d nergie l ouvreur doit tre install s il y a lieu par un lectricien autoris Le cordon de secteur doit atteindre la sortie au sol sans utilisation de corde de prolongation Si es necesario un electricista certificado debe instalar el cableado directo del suministro de energ a al abre puertas El cable el ctrico debe llegar al enchufe con conexi n a tierra sin utilizar un cable de extensi n e i TYPICAL SUPPORT BRACKET NOT PROVIDED JO SUPPORT TYPIQUE NON FOURNI OPTIONAL HEADER BRACKET MOUNTING BOARD POU AL nl O ERCOR e El Meet PLANCHE DE MONTAGE FACULTATIVE POUR SUP PORT D EMBASE TABLERO DE MONTAJE OPCIONAL DE SOPORTE DEL UMBRAL BRACING ATTACHE ARRIOSTRAMIENTO C BLE D ALIMENTATION PRISE i DE CONTACT DE 120V A CONTACT DE MISE LA TERRE CABLE DE ALIMENTACION A SSS UN TOMACORRIENTE DE 120 V CONECTADO A TIERRA EXTENSION SPRING RESSORT DE TRACTION RESORTE DE EXTENSION OR OU O TORSION SPRING RESSORT DE TORSION RESORTE DE TORSION NOTE For Low Headroom installations do NOT reduce doo
19. OIR NEGRO WARNING AA AVERTISSEMENT AA ADVERTENCIA MOTION DETECTOR DETECTEUR DE MOUVEMENT DETECTOR DE MOVIMIENTO RED ROUGE BLACK ROJO NOIR YELLOW NEGRO JAUNE AMAR LLO B ELECTRICAL SHOCK RED ROUGE ROJO BLACK NOIR NEGRO 5 4 3 2 STRIPED WHITE BLANC RAYE BLANCO RAYADO Purchased Separately INTELLIGENT WALL CONSOLE CONSOLE INTELLIGENTE DE MUH CONSOLA INTELIGENTE DE LA PARED WALL CONSOLE CONSOLE DE MUR CONSOLA DE LA PARED OPTICAL SENSOR SONDE OPTIQUE SENSOR PTICO CHOC LECTRIQUE CHOQUE EL CTRICO 26 SOME MODELS DO NOT COME WITH THIS FEATURE QUELQUES MODELES NE VIENNENT PAS AVEC CETTE CONFIGURATION ALGUNOS MODELOS NO VIENEN CON ESTA CARACTER STICA 2011 The Genie Company 3 2011 CHAINMAX 1200 LIMITED WARRANTY GMI Holdings Inc d b a The Genie Company Seller warrants to the original purchaser of the below identified garage door opener ChainMax 1200 Model 4022 Product subject to all of the terms and conditions hereof that the Product and all components thereof will be free from defects in materials and workmanship for the following period s of time measured from the date of purchase MOTOR GEARBOX Seller warrants the motor gearbox for the LIFETIME of the product CHAIN Seller warrants the chain for a period of FIVE 5 YEARS CORE UNIT PARTS Seller warrants all other parts and components of the Core Unit for a period of FIVE 5 YEARS ACCESSO
20. OM WALL CONSOLE IK SES ENT SR B MC SB BC WC wire routing Le at powerhead OL connector OPTIONAL DUAL WALL CONSOLE INSTALLATION Use only a Series Ill wall console when adding a second wall console The optional second Genie Series Ill wall console must be purchased separately TO TO WALL CONSOLE 1 FROM STBs FROM WALL CONSOLE BEES us STB BWC IWC WALL WALL Wire connector CONSOLE 1 CONSOLE 2 on Powerhead OR FROM STBs FROM WALL CONSOLE 1 FROM WALL CONSOLE 2 ji y NOT NOT E E m STB D IWC Wire connector on Powerhead WALL WALL CONSOLE 1 CONSOLE 2 20 2011 The Genie Company 3 2011 CHAIN TENSION ADJUSTMENT WARNING Observe all safety warning and precautions Disconnect power from opener and disconnect carriage in rail from bullet before beginning this task Visually inspect the chain every 6 months NOTE Tension adjustments should be made with the door in the down position and the carriage released At the center of the rail the chain should not be resting on the rail See adjustment illustration on right With the bullet NOT engaged to t
21. RIES Seller warrants all accessories for a period of ONE 1 YEAR Lifetime shall mean for as long as the original purchaser owns the home in which the product is originally installed The Core Unit consists of the powerhead wired wall control Safe T Beam system J Arm and rail Seller s obligation under this warranty is specifically limited to repairing or replacing at its option the Product or any part thereof which is determined by Seller to be defective during the applicable warranty period Any labor charges are excluded and will be the responsibility of the purchaser This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty is made to the original purchaser of the Product only and is not transferable or assignable This warranty applies only to Product installed in a residential or other non commercial application It does not cover any Product installed in commercial or industrial building applications This warranty does not apply to any unauthorized or improper installation alteration or repair of the Product or to any Product or component which has been damaged or deteriorated due to misuse abuse neglect accident failure to provide necessary maintenance normal wear and tear or acts of God or any other cause beyond the reasonable control of Seller and does not cover batteries missing or damaged parts from clearance or open box sales or repairs or maintenance to door
22. RPLE FLASHING ii REFERENCE CIRCUIT WIRING DIAGRAM FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM REFERENCE DIAGRAMME DE CABLAGE DE CIRCUIT a POUR OBTENIR DE L AIDE 1 800 35 GENIE REFERENCIA ESQUEMA ELECTRICO DEL CIRCUITO nr PARA OBTENER AYUDA LLAME AL 1 800 35 GENIE Opener circuit wiring diagram This wiring diagram is for reference only Sch ma de c blage de l ouvreur Ce sch ma de c blage est indiqu titre de r f rence uniquement Diagrama del circuito del operador Este diagrama es s lo para referencia Opening Cover May Cause Electric Shock A WARNING L ouverture du couvercle peut entra ner des chocs lectriques AVERTISSEMENT Abrir la tapa puede causar choques el ctricos Disconnect power from opener prior to removing cover A ADVERTENCIA Coupez l alimentation de l ouvre porte avant de retirer le couvercle Desconecte la electricidad del abrepuertas antes de quitar la cubierta POWER CORD CORDON DE SECTEUR CABLE ELECTRICO SCREW DRIVE MOTOR CHAIN MOTOR IMPULSI N DEL vae EE Adi E ds CADENA MOTEUR TORNILLO MOTEUR CHA NE MOTOR COMMANDE DE VIS MOTOR CONECTADOR CIRCUITO IMPRESO WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE STRIPED WHITE CHOKE J BOBINE D ARR T BLANC RAYE BLANCO RAYADO BOBINA DE CHOKE IN WHITE BLANC BLANCO Co SAFE T BEAM SAFE T BEAMO SAFE T BEAM WHITE p BLANC BLANCO Co Ex roo LCR BLACK NOIR NEGRO BLACK N
23. S3qd 9 0SU0 eM UO 3SV313 8 pue ssdud josuo II A UO uolle1 do JOOP N340 3SO12 D IInJ 15114 U31A A peonewone 195 SI 92404 J20H0J Las 6 3 2011 uonisod p soj 10 uado 1294102 UI SI JOOP pun suoung A y bursn jyu uu Aoul Joop do s pue 1461s ue NOA ILON Buiusel d 32H04 13S 6 deis q319njg Duo 335 UUM 3NUIUO 110 06 pue ng use sqJ1 4709 J9S 3 8 SHUI Joo 9AOUI 100P U23eA gt c b x SZ I a O SE gt G E gt E JSv313H A LES JsViliH 2 pue SS3ud f pue ss3 d 8 dii JSv313u ueui N3dO ATINA S 100p hpun ATOH pue ss3ud O S LIN DAHL HOOQ N3dO 8 abed 3xeu eu uo se3ourey BuiuuuueiDBoid UU enumuo 333 A LO si Buns l 2519494 3203100 Su DUO Ti P BR SN3dO 400 3 3513138 pue SS3ud 9 E 3 OU E pJeoq 6uin e1uo uodn s si A 1 Joop un Jessaau se Jeaday urebe 1591 ULI UMOP 129110 O OL ybnoau sda1s jeoda1 pue 9 sabed 0 uny HU UMOP au 0 1ueunsn pe ue p u AeW 1I S1 A 1 JOU s op pue pJeoq y x z au 6un e1uo Jaye sdoys IUJI UMOP 1294402 O OL ubnoJu sdajs 1e d l pue 9 sabed 0 UINJaY YUI UMOP Jas Apiedouduul ue 0 buipuodsai aq Ajdwis Aew iI pjeoq p x Z u1 s12e1u02 11 210J9Q sdojs x JOOP y J jueunsnfpy z 35V3134 pue ssiud 1 uonisod u do o Buluin1 1 uonoeulp 3 osuo IeM UO 9519591 pue spuo2 s Z UIUJIM do
24. Use this guide to ADJUST powerhead FORCE settings NOTE There are nine 9 force levels PROGRAM Press on the powerhead and hold until both Door closing force is FACTORY set and requires no adjustment for normal operation Never increase the door closing force to 1 compensate for a damaged door or a binding lights turn steady ON Release button door track Lights go out and Round BLUE light comes ON Never adjust force to compensate for a broken door spring 2 Press three times Round RED light comes ON PROGRAM Perform monthly CONTACT REVERSE TEST as 3 Press once to enter the Force Programming described on page 18 menu The round LED will flash BLUE 3 times then the current Force setting for UP force will display on the LEDs See table below Force settings are pre programmed at the factory and learned during the Open Close Limit settings 4 If current UP Force setting is good skip to Step steps Some additional Force may be increased 5 Press S to increase or to decrease UP Force For normal use Force settings should not need settings within the available range djustment with this unit s SA conditions that might suggest an 5 Dress to set UP Force level The long LED will adjustment is necessary are flash BLUE 3 times then the current Force setting for DOWN force will display on the LEDs Doors with very stiff weather seals Doors that start down then STOP and re
25. VERVIEW Not available on all models Powerheads equipped with a motion detector sensor provide additional security when exiting or entering the garage area This sensor works by detecting body heat Range of detection may be reduced when the temperature in the garage is close to body temperature NOTE Detector positioning on the powerhead provides for monitoring below the powerhead OPERATION Detector sensor is always ON There are NO user controls or adjustments Lights automatically turn ON when a change is detected and will turn OFF after 4 minutes of no change Motion detector sensor will not turn OFF lighting turned ON at the wall console Lighting turned ON at the wall console will remain ON until wall console turns FE OFF or opener is used RESET OPEN CLOSE TRAVEL LIMIT Performing all ten 10 Limits Force setting steps pages 6 7 erases previous Limits Force settings NOTE The opener will not close the door automatically unless the Safe T Beam System is installed and Limits are programmed 2011 The Genie Company CARRIAGE ENGAGE DISENGAGE Use Release Handle to manually connect or release chain bullet to Carriage TO RELEASE CARRIAGE 1 Pull handle DOWN then let go 2 Manually move door until carriage releases from bullet 3 Raise or lower door manually Release Handle PULL TO RECONNECT CARRIAGE 1 Verify RED block is in the UP position 2 Manually move door until carriage en
26. WARNING To reduce the risk of severe injury or death READ AND FOLLOW ALL SAFETY INSTALLATION 5 Do NOT connect the opener t source of power until AND OPERATION INSTRUCTIONS If you have instructed to do so questions or do not understand an instruction call 6 Locate the wall console The Genie Company Within sight of the garage door Install only on a properly balanced sectional or At minimum height of 5 feet so small children one piece garage door An improperly balanced are not able to reach it and door could cause severe injury Have a trained door Away from all moving parts of the door system technician make repairs or adjustments to 7 Install the Entrapment WARNING Label next to the cables spring assemblies and other hardware before wall console in a prominent location installing the opener 8 After installing the opener the door must reverse Remove all ropes and remove or make inoperative all within 2 seconds when it contacts a 1 1 2 inch high locks connected to the garage door before installing object or a 2 x 4 board laid flat on the floor opener Where possible install the door opener 7 feet or more above the floor For products having an emergency release mount the emergency release within reach but at least 6 feet above the floorto avoid contact with vehicles to prevent accidental release INFRARED PROTECTION FUNCTION When garage door is opening its movement will not be influenced if the Safe T B
27. adjustment Is this opener installed on a one piece door Normal speed for one piece door is lowest speed setting If carriage travel is less than 6 feet opener configures programming for a one piece door Check door speed See page 22 Door opener runs slow TR O U B L E S H OOTI N G G U I D E POWERHEAD LEDs FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM Powerhead LED Possible Problem Round LED Long LED OFF OFF Check power supply No response from unit Contact a trained door system technician ON RED ON RED E STEADY STEADY Limits NOT set properly Reprogram Limits see pages 6 7 Unplug unit wait 5 seconds plug in ON RED ON RED FLASHING FLASHING Component failure Contact a trained door system technician ON BLUE FLASHING Remote NOT programmed Program remote see page 9 Program remote using IntelliCode9 IntelliCode9 1 remote NOT 2 remote see page 9 then program programmed IntelliCode9 1 remote using instructions on page 10 GH E O i SN Seti BEE Remove obstruction recheck unit ON RED obstruction FLASHING Safe T Beam signal Check alignment of Safe T Beam pair interference and nearest other Safe T Beam pair Door contact in up or down Remove obstruction ON RED travel FLASHING Door component failure Check door spring track rollers hinges detected and fixtures ON RED DO NOT unplug unit STEADY Wait until LED clears before operating 2011 The Genie Company 3 2011 25 ON PU
28. and receiver Connect the opener into an outlet on a circuit different from that to which the receiver is connected Consult your local dealer 2011 The Genie Company 4 Press both V and LOST OR STOLEN REMOTE CLEARING MEMORY Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad NOTE Follow the PROGRAM REMOTE TO POWERHEAD steps to re enter remaining or new remotes See page 9 PROGRAM 1 Press and hold until both lights come ON BLUE Release button BLUE light comes ON 3 Press again and long LED flashes PURPLE simultaneously on the powerhead and hold until both LEDs flash BLUE e Verify memory is cleared Press a remote button that was previously programmed to N c SS RE NE a Lea EN Ld de x 2 Lights go out and Round the powerhead Remote will not activate door opener Garage door opener will operate normally using wall console Program remaining or new remotes as shown on page 9 Your door opener will no longer recognize any signal received from the missing remote or any other which has not been reprogrammed to the powerhead 3 2011 If your garage door opener has a Serial Number sticker which looks like this in which the first two numbers are 10 or higher your opener is equipped with INTELLICODE 2 MODEL AC SR3 FCC ID iila A C SR3 THE GENIE COMPANY Residential Door Operator IS A CSD 120V 60HZ 5
29. components ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN TIME TO THE APPLICABLE WARRANTY PERIOD REFLECTED ABOVE NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you IN NO EVENT SHALL GMI HOLDINGS INC OR ITS PARENT OR AFFILIATES BE RESPONSIBLE FOR OR LIABLE TO ANYONE FOR SPECIAL INDIRECT COLLATERAL PUNITIVE INCIDENTAL OR CONSEQUENTIAL DAMAGES even if Seller has been advised of the possibility of such damages Such excluded damages include but are not limited to loss of use cost of any substitute product or other similar indirect financial loss Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Claims under this warranty must be made promptly after discovery and within the applicable warranty period To obtain warranty service you must contact Genie customer service and provide proof of the date and location of purchase and identification as the original purchaser Call Genie Customer Service toll free at 1 800 354 3643 to speak with a trained representative Purchaser must allow seller a reasonable opportunity to inspect Product claimed to be defective
30. e corde de prolongation Sj es necesario un electricista certificado debe instalar el cableado directo del suministro de energ a al abre puertas El cable el ctrico debe llegar al enchufe con conexi n a tierra sin utilizar un cable de extensi n TYPICAL SUPPORT BRACKET NOT PROVIDED SUPPORT TYPIQUE NON FOURNI ESCUADRA DE SOPORTE T PICA NO SE INCLUYE HEADER BRACKET MOUNTING BOARD not provided PLANCHE DE MONTAGE FACULTATIVE POUR SUPPORT D EMBASE non fourni TABLERO DE MONTAJE DE SOPORTE DEL UMBRAL no se proporciona POWER CORD TO 120V GROUNDED OUTLET C BLE D ALIMENTATION PRISE DE CONTACT DE 120V CONTACT DE MISE LIFT SPRING LA TERRE RESSORT DE LEVAGE CABLE DE ALIMENTACI N RESORTE DE ELEVACI N A UN TOMACORRIENTE DE A 120 V CONECTADO A TIERRA Cus FIG 3 2 SAFE T BEAM SENSORS PALPEURS de SAFE T BEAM SENSORES SAFE T BEAM WARNING To reduce the risk of injury to persons or damage to property Use this opener only with a one piece or sectional door AVERTISSEMENT Pour diminuer le risque de blessures corporelles ou d endommagement mat riel Utiliser cet l ouvreur uniquement avec les portes section ADVERTENCIA Para reducir el riesgo de lesi n a las personas o da os a la propiedad ONE PIECE DOOR SECTIONAL DOOR utilice este abre puertas solamente con una puerta de una pieza o PORTE D UNE PI CE PORTE SECTIONELLE secciondl PUERTA DE UNA SOLA PIEZA PUERTA SE
31. eam is obstructed If the Safe T Beam is obstructed before the garage door fully closes the door will not close When the garage door is closing if Safe T Beam is interrupted by person or obstacle the garage door will stop its downward travel and reverse automatically to its fully opened position Remove Safe T Beam obstruction If the Safe T Beam System fails loses power or is installed improperly press and hold the wall console open close button until the door reaches its fully closed position If you release the open close button on the wall console during the closing movement the door will reverse automatically to its fully opened position 2011 The Genie Company 3 2011 5 uonisod p soj JO uado 1294102 UI SI JOOP JUN suo3nq 13449 bursn Ju uu Aoul 100p dois pue 1461s ue noA 310N Sulyse q31 ng puno 44S 35V3138 pue SS14d INO ou o3 Hulluwesbod sy 10J spuo es 0 Hem uonounj buruuuejb60Jd y dixe OL 4e3s9J pue buruuuuedb04d yxa ISNW noA Ajdod palajus JOU SEM s nueuJ fBuruweiboid eum au siu je 35131348 44 q3S012 ATIN1 100p Run qTOH Pue SS3ud G3 NO 24102 5 3 Y10Q 10 GUO j 31ON Puluwelboid ue NO 3U0 pue dOls NO 52uJo 131 038 JI NO auo sq31 nig r 131 nig H109 33S days ye 118 531 eseo d 1noauun e jo Juana Y uj NO 310 q31 punou 33s Jeedde sq371 Buluspj J q34 o USUM poun2 o njg Duo 33S seu sda s eseu1 buunp 1noeuun Buruuweiboid y
32. ed LED flashes Check for obstruction Check alignment Verify wire routing from FROM STBs FROM WALL CONSOLE STBs to STB connection in E powerhead USED USED Check for signal interference 4 i from another Safe T Beam SB BWC WC unit No STB Red or Green LED displayed Check wiring and wire connections One Piece Door Sectional Door FIG 6 1 Door balance Stops after contacting the 2 x 4 board and does not reverse it may need an adjustment to the down limit Return to pages 6 7 and repeat steps 1 through 10 to correct down limit Test again Repeat as necessary until door reverses upon contacting board EU Se FIG 6 2 2 x 4 under center of door opening 3 2011 CHANGE LIGHT BULBS WARNING Observe all safety warning and precautions Improper light bulb removal or replacement could result in Death or Serious Injury Disconnect power from opener before beginning this task When replacing light cover make sure wires are not pinched or near moving parts 1 Disconnect power to door opener Open powerhead light cover Remove light bulb s Replace with maximum 100 Watt light bulb s Do NOT use light bulbs with greater than 100 Watt rating Close powerhead light cover 2 Reconnect power to door opener Test light operation MOTION DETECTOR O
33. ew There are four Powerhead program menus Remote Program Default menu Limits Program Speed Program Force Program Programming steps for Limits and remotes are found on pages 6 through 10 Force and Speed settings are set at the factory and do not normally require adjustment programming Custom programming instructions for Speed and Force are located in the Troubleshooting Section of this manual These are the basic steps to enter into the four programming menus PROGRAM 1 Press s and hold until both BLUE lights come ON then release 2 Both LEDs go out and Round BLUE light comes ON You are in the Program Menus at the Remote Programmino By using the a orthe button you can navigate to the Limits Speed or Force program menus and the LED display will change accordingly Each program menu has a specific LED display LED Display Remote Round Blue Q Press Program Default B Limits Long Blue De Speed Round Blue O e Long Blue A X3 Force Round Red PROGRAM 3 Press button to enter into the program menu functi ns If you have entered into an unwanted program menu and are not sure where you are do not press any buttons for 30 seconds The programming function will time out after 30 seconds if there is no key stroke activity 3 2011 5 OVERVIEW REMOTES AND OPTIONS WARNING A moving door can cause serious injury or death Keep people clear of opening while door is moving
34. gages bullet 3 Raise or lower door using remote or wall console FIG 6 3 Carriage Release DOOR d TO RELEASE or RECONNECT CARRIAGE PULL DOWN AS SHOWN AND LET GO RED BLOCK WILL RETURN TO ORIGINAL POSITION AND BULLET WILL BE RELEASED TEL D J JR 10 a installation TO DISENGAGE PULL DOWN AND TOWARDS DOOR THEN LET GO for SE TO REENGAGE PULL DOWN AND TOWARD POWERHEAD THEN LET GO TO RELEASE or RECONNECT CARRIAGE PULL DOWN AND LET GO FIG 6 4 Carriage Release cut away view 3 2011 19 This opener has a Serial Number sticker in which the serial numbers begin with 10 or higher ATTENTION If your garage door opener has a Serial Number sticker which looks like this in which the first two numbers are 10 or higher your opener will operate using this Series IIl wall control MODEL AC SR3 THE GENIE COMPANY FCC ID l C SR3 Residential Door Operator A CSWI D 120V 60HZ 5A S N TOXXXXEXXXXXXX BUT LU A R gt 800 35GENIE OR WWW GEN ECOMPANY COM Follow the instructions on this page Wall consoles from other manufacturers may not work with openers of these serial number groups Genie Series wall buttons and Series Il wall consoles will not work with openers of this serial number group WALL CONSOLE OVERVIEW Use only the Series Ill wall console provided with this unit Wall console has three buttons and one indicator light Indicator Light Indicator light will dis
35. he carriage tighten adjustment nut until chain does not at the center of the rail rest on rail Do NOT overtighten sthere rust on chain Contact a trained door system technician for chain replacement Are there kinks or twists in the chain Contact a trained door system technician for chain replacement Tighten nut to increase tension on chain REMOTE BATTERY REPLACEMENT Replace remote battery with a CR 2032 coin cell battery 1 Open the remote case using a washer or coin that fits into the slot at the top of the remote 2 Replace battery 3 Align components and snap case closed 2011 The Genie Company Adjustment required Correctly adjusted 3 2011 Chain at center of rail KN Approx 1 8 21 ADJUSTMENT GUIDE spEED SETTINGS Speed settings are pre programmed at the factory for the maximum speed Speed settings should not need adjustment with this unit However travel speed for the opener in both the open and close directions can be adjusted to slower speeds to minimize normal wear for heavy sectional doors NOTE One piece doors are automatically set during Limits programming to the slowest speed and opener speed cannot be reset for one piece doors FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM CHANGE SPEED SETTING Use this guide to ADJUST powerhead SPEED settings There are three 3 Speed settings available on this unit for the open and close directions Do
36. is 1snuu JOOP y pJeoq s12e1uo2 JOOP USYM e osuoo UE Buisn Joop abeseb soj FPEO M PU HOO PU UNIO U n AEI o5 buiuedo 100p ebejJeb jo 19149 Japun Du piej pjeoq t X Z e lejd und 0 urbeq p noo Jeuedo 100p buruuuej6oud Punung pedAoy ssa 9JIM 10 330UJa1 2 OSUO UM buipnj ur 4auado YUM e d 01 u ip u3 Ao e LON OG S L L BUIAOUW si JOOP ajIym Buluado jo 18312 do d d y bunse3 2519194 esp 10 Ainfui snolias esne ue 100p BuIAOU y 198140 210399 GALIIdWOD 29 LSNW ebed snolnald ay uo sbunss z117 pue 824104 9u DNINHVA W ISILISHIAIHIOVINOD e osuoo UE Buisn 100p ebejeb u do osn 0 pe si jeuedo 100p abeieb Ano 333 d110 si fuiuweiboid peausamod diseg S910UJ9J J9YIO 104 JESSIIIU se jeaday Joop 9 e19d0 IM 21091 au JO Ssaid 1xeu u nig ysel sa31 4104 335 110 031 u1oq 33S 3SV313N9 pue Ss3ud e Buiuselj q31 A ldind uoj 335 NO euro q31 anjg punou 33S NA A PRIS JSV3 13d 3sva1au c 10H pue ss3ud 1 pue ssiud S910UJ9J L eepo i o1u buisn suorpnasur Buiuuuue_iDoid 10 01 ebed 99S L sepo r e13u 01 Z eepo rireaul UJOJJ YIJIMS O MOY pue S 1OoUJ 1 Z pue L o PONIJU uo uoneuuoJur PUOIJIPPE 1049 obed 0 Jajay W9 S S JLINIIS ssa y Z e9po i e1u BY YIM esn 10 1959 40 SI JOW I sIy Jeuedo SIY YUM pepi oJd s e1oulaJ y 104 91 suononajsur BUIMO OJ SY SALON pouweiboid aq 01 u
37. or type one piece or sectional door weight and balance and condition of door components track affect door speed Speed adjustment may not be available for some installations depending on these factors PROGRAM 1 Press on the powerhead and hold until both lights turn steady ON Release button Lights go out and Round BLUE light comes ON 2 Press gt two times and the Round BLUE and Long BLUE lights come ON 3 Press _ once to enter the Speed Programming menu The round LED will flash BLUE 3 times then the current Speed setting for UP travel will display on the LEDs See table below 4 Press a to raise or to lower UP Speed settings within the available range NOTE Faster door speeds may not be available PROGRAM 5 Press _ to set UP Speed level The long LED will flash BLUE 3 times then the current Speed setting for DOWN travel will display on the LEDs 6 Press to raise or to lower DOWN Speed settings within the available range NOTE Faster door speeds may not be available PROGRAM 7 Press to set DOWN Speed level Both LEDs flash BLUE to confirm S dL Powerhead LEDs pce Ee Round LED Long LED Default LED display is the current Speed setting LED Speed indicator colors Red Red Purple www 10115 wo LCL A ell 22 2011 The Genie Company 3 2011 ADJUSTMENT GUIDE Force SETTINGS FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM CAUTION CHANGE FORCE SETTING
38. oynq ype 104 Z da1s ybno1y1 enunuo pue dais ul ulbeg UOne o peasylamod 0 s e1oureJ Bung 35V3138 pue SS14d NO 3UO sqq1 9njg H104 33S dind sel saqJ14 0q 33S JsV3 13H pue SS3uUd syed eu pue 100p HulAow woy Aeme e s os und 0 urbeq p no gt Jeuedo 100p buruuuej6oud Punung ped a ssa 9JIM JO JOWI 2 0SUO PM Buipnpui 1ousdo YUM ejd 03 uagp ru MOIE LON OG buriAOUuu si JOOP ajIym Bulu do jo 18312 do d d y u3eop 10 Ainful snolias esne ue 100p BuiAoui V DNINSVM Wy O O HS EH CREDIS QU AVIHIIMOd OL 110W134 Z eAGODITIFLNI WV4DO93d C 3 2011 2011 The Genie Company osn 03 pe si Jeuedo 100p abeseb sno e3e duuo si BuriuuuueiBoid jeuordo ry uoneJjedo Aan O uoning lt a gt ssoJd pue uid 19 U SDUODAS OS HEM 9 21138 UA J9auado pue ulebe uoynq lt a w DIOU pue ssaJd s n g use sq31 u1oq ppaysamod UO 395 pue se 1 u y urebe puodas UOJINQ Ca p ou pue SSeld O ajdind NO 21103 q31 Duo pbay1amod uo 225 pue se 1 Ser S910UJ9J L 62PODIIOIU 19470 Aue 104 Jessaau se 1eoday 1591 JOOP 321900 IM 910UJ81 a JO ssaJd 1xeu u en g NO 9uJo peay1amod y uo sq31 u1oq 33S 3SV3 138 pue uoynq wes aui SSIHA 910UJ23J L sepo i a3u 24 UO ejdundg NO 202 q31 Duo 335 3573134 pue uonngq e SS4dd 3 0U31 e2PODIJIPIU 24 UO puo2 s UOJNQ cae DIOU pue ssaJd Nid podfay ssaja4im INO 191
39. play Red when wall console is properly wired and Sure Lock is OFF When Sure Lock is ON indicator light flashes Open Close Button Use this button to open or close garage door When Sure Lock is ON the Open Close button will CLOSE door only Note Constant button pressure in the CLOSE mode will override error responses in the powerhead and close door Independent Light Control Button Use this button to turn powerhead lights ON Powerhead lighting will remain ON until this button is pressed again or a door action has been completed Note If opener has a Motion Detector sensor the sensor will keep powerhead lights ON as long as motion is detected Sure Lock Button When Sure Lock is ON the powerhead cannot be activated by the wall console or a remote Press and hold for 5 seconds or until Indicator Light flashes to activate Sure LockTM Press and release to turn Sure Lock OFF Open Close Button Open and closes door from inside garage Sure Lock Button LOCK disables controls after door is completely closed UNLOCK allows controls to work normally Indicator Light Red indicator light is always ON When Sure Lock is ON the indicator light flashes Independent Light Control Button Controls door opener lights from inside garage Tip If indicator light on wall console comes ON but there is NO operation from buttons verify wall console FROM STBs FROM STBs FROM WALL CONSOLE FR
40. r arm lengths by cutting door arms To clear door reposition door arms with greater angle REMARQUE Pour les installations basse hauteur ne PAS r duire la longueur du bras de la porte en coupant les bras de la porte Pour d gager la porte repositionnez les bras de la porte un plus grand angle NOTA Para instalaciones a alturas bajas NO reduzca las longitudes de BRAS DE LA PORTE los brazos de la puerta cort ndolos BRAZO DE LA PUERTA Para despejar la puerta vuelva a colocar los brazos de la puerta en otra posici n con un ngulo mayor SAFE T BEAM SENSORS PALPEURS de SAFE T BEAM SENSORES SAFE T BEAM FIG 3 1 MAX 6 MIN 5 6 po 15 cm MAX 5 po 12 7 cm MIN MAX 6 MIN 5 12 2011 The Genie Company 3 2011 TYPICAL ONE PIECE DOOR INSTALLATION FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM INSTALLATION TYPIQUE D UNE PORTE DE GARAGE D UNE PIECE POUR OBTENIR DE L AIDE 1 800 35 GENIE INSTALACION HABITUAL DE PUERTA DE UNA SOLA PIEZA PARA OBTENER AYUDA LLAME AL 1 800 35 GENIE If required direct wiring of power supply to opener must be installed by a licensed electrician Power cord must reach grounded outlet without use of extension cord e c blage direct de l alimentation d nergie l ouvreur doit tre install s il y a lieu par un lectricien autoris Le cordon de secteur doit atteindre la sortie au sol sans utilisation d
41. r website The following Safety Alert symbol and signal words are used throughout this manual to call attention to and identify different levels of hazard and special instructions A This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and the word DANGER WARNING or CAUTION DANGER indicates an imminently hazardous situation which if NOT avoided will result in death or serious injury WARNING indicates a potentially hazardous situation which if NOT avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if NOT avoided may result in injury or property damage The word NOTE is used to indicate important steps to be followed or important considerations IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Potential Hazard__ Effect Prevention _ WARNING Keep people clear of opening while Door is moving de Do NOT allow children to play with the Door Opener Death or Serious Do NOT operate a Door that jams or one that has a broken Injury spring WARNING urn OFF power before removing opener cover When replacing cover make sure wires are NOT pinched or Could resultin near moving parts Death or Serious Injury Opener must be fully grounded WARNING DO NOT try to remove install repair or adju
42. so muss der Importeur vor dem Gebrauch sicherstellen dass die Sendeger te auch solchen lokalen Bestimmungen entsprechen welche von den Bestimmungen der USA und Kanadas abweichen ELE T tie A RA Je ELS gt Es MMS ACRI PR 48 AREER T OS DATAE ELSE EE TRI LO A IX PAE EK Z TE 4 WIRE ss t FE 8 ELO EE zs FH x DITS AID E 439 SKAMMER NE 2 PERS b 75 530 24D o yA HERNANDO xUJJS 2 amp E I 0 2 7 OTEBJ2STELZTEHUL ES LALARO F a O a ECVE A dn ent EU at CH EGA EE INT A EH TZ JE HAOHAOA C 310 OZ 2 573 5 C 6 235 2 72 ETE MEAT L Z E L ART dE D EE Of zi c eio A AE SMES S7lOHOF ok QTAR eot SLIDE Z EF CE AA DE 4401 27 ARH et LICE Hl EHAEO 7IEF CRE AAAA AF82 82 SAAE AES TIO SM SAHE SHARE ERA 919 Auf EAH oke 044 AAH EE dm CO REA BHH EFV se EY TT HV IN gt mjn rlo Iu rir re 2 S 52 IP FF Lin ia ol m gt Tlo z O 6 MA I N TE NA N CE amp TR O UBLES H OOTI N G FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM If you have any questions please do not hesitate to contact customer service at 1 800 35 GENIE IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of severe injury or death READ AND FOLLOW ALL INSTRUCTIONS Never let children operate or play with the door controls Keep the remote away from children Always keep the moving door in sight and away from people and objects until the door is completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR
43. st springs or anything to which door spring parts are fastened such as nec lie wood blocks steel brackets cables or other like items Death or Serious Installations repairs and adjustments must be done by Injury a trained door system technician using proper tools and instructions 2 2011 The Genie Company 3 2011 OPENER FEATURES INTELLICODE 2 Access Security System A new generation superior encryption system that enhances the security of the door opener by continuously changing the access code each time the remote is used The door opener responds to each new code only once An access code copied from a working system and tried again will not control the door opener Wall Console Series III Operates door opener from inside garage The Wall Console has an Indicator Light with Open Close Sure Lock and Independent Light Control buttons IN HomeLink COMPATIBLE www homelink com MM and Car2U compatible Refer to the programming instructions on page 10 and then follow the HomeLink or Car2U instructions in your car owner s manual SAFETY FEATURES Safe T Beam STB Non Contact Reversing System Puts an invisible beam across the door opening The door stops and reverses to the full open position if anything passes through the beam LED indicator lights on the powerhead and on the STBs provide a self diagnostic code if an operational problem exists Safe T Reverse Contact Reversing System Automatically
44. ting 17 26 Important Safety Instructions 17 Routine Monthly Maintenance 18 Door Balance Spring Tension 18 Safe T Beam System Che lt ck 18 Contaci Reverse TEST aerario riunn pctil 18 Change LIO BUIDS uu ae dan no ui 19 Motion Detector Overview 19 Reset Open Close Travel Limi 19 Cange ee ee te e 19 Wall Console Overview 20 Optional Dual Wall Console Installation 20 Remote battery Replacement 21 Speed Adjustment Guide xs capinsssssavsccssassadscavecesnep atnessasneardssiedsuanasionissieadvnaneins 22 Force Adjustment GIGS riera han 23 Troubleshooting Guide Operation 24 25 Troubleshooting Guide Powerhead LEDS sees 25 Reference Wiring Diagram
45. u L Dj4and p ap ozbig OUDS23ADA Jap 2110d0S yoddns ssequz 1949819 JepeeH JOOVIVLSNI 130 TVNOISIJO YA Tludv2 i a SES HO31VTIVISNIO 1INNOISS310Hd VE y IVY H311VLSNI 1VNOISS110Hd CL OBID a1aj uD ap JOPDSDA LZ onDuo edeup ap axy 5uo7 uid SIAa D VIDH3N3 V 13G VZ38VO JoONVSSIfd 30 3131 QV3H 41MOd Jal Jap 10122u0 8 Jap 1012200 US np uon unf ap UOUIEIW US np uonounf ap uojew a 10328uuo Iey 1o 3 uuo2 rey lt 2 osa TV VLN3A 3G 1318 11V130 3G 1lVu 0214128J8 9 QD Jnepesepuopio e p10 19M04 SO U10 SO DIDd 1f ZV os oq 2 Daf SIA Sap anod 1318 2es 2 1IOA 11V4 TIVL38 11 3 2011 Pd Pd REFERENCE POWERHEAD amp RAIL ASSEMBLED VIEW REFERENCE VUE DE LA TETE D ALIMENTATION amp DU RAIL ASSEMBLE REFERENCIA VISTA DEL CABEZAL ELECTRICO Y RIEL ENSAMBLADOS SM9J5S 10 Beq 31119 s NX lt A AV REMARQUE Utilisez la console sur le mur et les capteurs de s curit fournis avec cet appareil NE PAS substituer la console du mur ou les capteurs de s curit NOTA Use la consola de pared y los sensores de seguridad proporcionados con esta unidad NO sustituya la consola de pared ni los sensores de seguridad NOTE Use wall console and safety sensors provided with this unit Do NOT substitute wall console or safety sensors 2011 The Genie Company 3 TYPICAL SECTIONAL DOOR INSTALLATION ror HeLp 1 800 35 GENIE OR WWW GENIECOMPANY COM INSTALLATION TYPIQUE SUR UN
46. verse 6 If current DOWN Force setting is good skip to before they close Step 7 Press to increase or to decrease Doors that start up but STOP before they DOWN Force settings within the available range completely open 7 Press __ to set DOWN Force level Both LEDs flash BLUE to confirm Force Level LED indicator colors Blue m ae ol o Blue Force Level 2 Blue Blue Force Level 3 We Br poete CIE A A IES AO COS AA S CIA AO o JOB S BEES 2011 The Genie Company 3 2011 TROUBLESHOOTING GUIDE operation FOR HELP 1 800 35 GENIE OR WWW GENIECOMPANY COM PROBLEM WHAT TO DO Check power source Plug a lamp into outlet used for powerhead If lamp works power source is OK If not check fuse or circuit breaker If power is OK Check connections at powerhead terminals and at wall console Limits must be set with door arm connected to door Check if wall console Sure Lock is ON Turn Sure Lock OFF amp check operation Check for reversed broken or cut wires Staples can cut insulation and short wires Repair or replace Opener does NOT run from wall console Make sure carriage is engaged to chain bullet See pages 11 and 19 Refer to Installation poster or download poster from WWW GENIECOMPANY COM Ensure carriage is in engaged position See page 19 Check to make sure chain is not broken or OFF its pulley Check FORCE ADJUSTMENT See page 23 Opener runs but door
Download Pdf Manuals
Related Search