GE JVM1790 User's Manual
Contents
1. NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws a hole large enough for the power cord to fit through and a cutout large enough for the exhaust adaptor Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom ASSEMBLE AND INSTALL ADAPTOR lt _ Exhaust Adaptor lt lt Blower Plate SS Back of Place the oven in its upright position with the top of the unit facing up Insert the tabs on each side of the damper into the holes at the inside rear of the adaptor Attach the exhaust adaptor to the blower plate with the two bronze metal screws provided Make sure that the damper pivots easily before mounting oven You will need to make adjustments to assure proper alignment2. DUCT HORIZONTAL DUCT Adaptor in Place for Outside Top Exhaust See page 12 See page 15 RECIRCULATING NON VENTED DUCTLESS A Charcoal filter Accessory Kit is required for the non vented exhaust See your Owner s Manual for kit number See page 19 11 Installation Instructions A OUTSIDE TOP EXHAUST vertical Duct INSTALLATION OVERVIEW Al Attach Mounting Plate to Wall A2 Prepare Top Cabinet A3 Install Adapter A4 Mount Oven A5 Adjust Exhaust Adaptor A6 Connect Ductwork ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 4 2 cm onto each bolt 12 To use toggle bolts Spacing for Toggles More Than Wall gt Thickness I i Toggle Wings Mounting i j Toggle Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate
3. over onto the top side The oven should be resting in Center the Styrofoam Ne Find the studs using one of the following methods A Stud finder a magnetic device which locates nails OR B Use a hammer to tap lightly across the mounting surface to find a solid sound This will indicate a stud location After locating the stud s find the center by probing the wall with a small nail to find the edges of the stud Then place a mark halfway between the edges The center of any adjacent studs should be 16 40 6 cm or 24 61 cm from this mark 3 Draw a line down the center of the studs THE OVEN MUST BE CONNECTED TO AT LEAST ONE WALL STUD Pull the carton up and off the oven The mounting plate is attached to the back of the oven Remove the two screws holding it to the oven The plate will be used as the rear wall template and for mounting the oven to the wall Set the oven upright Remove and properly discard plastic bags and Styrofoam Open the oven door and remove the styrofoam pack from inside the oven Remove the tape covering the turntable hub Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position beneath flat bottom cabinet Mounting Plate Tabs Touching the Cabinet Bottom At least 30 76 2 cm up to 36 91 4 cm Plate position beneath recessed bottom cabine
4. top cabinet Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom 16 ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST Remove the three screws that hold the blower plate to the oven Slide blower plate from under its retaining flange Remove and save the screw that holds blower motor to oven Retaining Blower Plate Blower Motor Screw Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit BEFORE Fan Blade Openings Facing Up Rotate blower unit counterclockwise 180 Before Rotation After Rotation Back of Oven Gently remove the wires from the grooves Reroute the wires through grooves on other side of the blower unit Before Rerouting After Rerouting Wires Routed Through Right Side Wires Routed Through Left Side Before Rolling 7 Installation Instructions Roll the blower unit 90 so that fan blade openings are facing out the back of the oven After Rolling SAL A PEES Oven Oven Locate the two knockout plates on the rear oven panel near the top of the oven Using tin snips carefully cut the web area from the two holes side by side that secure the knockouts to the oven Cut all four webs on both rear knockouts this will allow the ventilation fan ai
5. with your house exhaust duct after the oven is installed MOUNT THE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from overtightening screws NOTE When mounting the oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord Lift oven tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a selfaligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet Installation Instructions MOUNT THE OVEN continued ADJUST THE EXHAUST ADAPTOR Cabinet Front Open the top cabinet and adjust the exhaust adaptor 7 Cabinet Bottom Shelf to connect to the house duct Filler Bl
6. 61 2 kg CAUTION For personal safety this product cannot be installed in cabinet arrangements such as an island or a peninsula It must be mounted to BOTH a top cabinet AND a wall NOTE For easier installation and personal safety it is recommended that two people install this product IMPORTANT PLEASE READ CAREFULLY FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Ensure proper ground exists before use You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded Where a standard two prong wall receptacle is encountered it is very important to have it replaced with a properly grounded three prong wall receptacle installed by a qualified electrician DO NOT UNDER ANY CIRCUMSTANCES CUT DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD DO NOT USE WITH AN EXTENSION CORD ELECTRICAL REQUIREMENTS Product rating is 120 volts AC 60 Hertz 15 amps and 1 5 kilowatts This product must be connected to a supply circuit of the proper voltage and frequency Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowat
7. ET TEMPLATE replacement is the responsibility of the customer If the unit is damaged by the installer if other than the customer repair or replacement must be made by arrangement between customer and installer PARTS INCLUDED Installation i i N STALLATIO Instructions STRUCTIONS HARDWARE PACKET Wood Screws Y x 2 Separately Toggle Bolts and 4 Packed am wing nuts Ys X 3 Grease QUANTITY Self Aligning Machine Screws 4 28 x 314 Self Aligning Machine Screw Y 28 x 2 Nylon Grommet for metal cabinets 2 2 1 2 y Exhaust Adaptor Metal Screws 1 black FUND Ye x V2 2 bronze Power Cord Strap 1 plastic You will find the installation hardware contained in a packet with the unit Check to make sure you have all these parts NOTE Some extra parts are included Installation Instructions TOOLS YOU WILL NEED A Ruler or tape measure and aabuso stota sttail a straight edge 1 and 2 Phillips screwdriver Aia Carpenter square optional f Oc F Tin snips for cutting damper if required Scissors to cut template if necessary Electric drill with 6 As Ye and drill bits Filler blocks or scrap wood pieces if needed for top cabinet spacing iS 3 used on recessed bottom NI n cabinet installations only loves ED Safety goggles Stud finder or Hammer optional Duct and masking t
8. Installation Above the Instructions Cooktop Oven JVM1790 Questions Call 1 800 361 3400 or Visit our Website at geappliances ca BEFORE YOU BEGIN Read these instructions completely and carefully Note to Consumer Keep these instructions for future reference gt IMPORTAN T Save these y Skill level Installation of this appliance requires Dees 10r eran pe crores tise basic mechanical and electrical skills e IMPORTAN T Observe all Proper installation is the responsibility of the installer governing codes and ordinances Product failure due to improper installation is not e Note to Installer Be sure to leave these covered under the Warranty instructions with the Consumer For a French version of this manual visit our Website at www geappliances ca Pour une version fran aise de ce manuel consultez notre site www electromenagersge ca READ CAREFULLY KEEP THESE INSTRUCTIONS 350A4502P476 Installation Instructions CONTENTS Recirculating 5 Attach Mounting Plate to Wall General information Preparation of Top Cabinet Important Safety Instructions Adapting Blower Electrical Requirements for Recirculation Hood Exhaust Mount the Oven Damage Shipment Installation Installing the Charcoal Filter Parts Included Before You Use Your Oven Tools You Will Need Mounting Space Step by step installation guide Placement of Mounting Plate Removing the Mounting Pl
9. Wall Cap 40 Ft 12 2 m 40 Ft 12 2 m 3 Ft Straight Duct 3 Ft 0 9 m 34 x 10 8 2 x 25 4 cm Rectangular B 90 Elbow 10 Ft 3 m 20 Ft 6 1 m Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Total Length NOTE For back exhaust care should be taken to align exhaust with space between studs or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust Installation Instructions NOTE If you need to install ducts note that the total Maximum duct length duct length of 3 4 x 10 8 2 x 25 4 cm rectangular or For satisfactory air movement the total duct length of 6 15 2 cm diameter round duct should not exceed 3 4 x 10 8 2 x 25 4 cm rectangular or 6 15 2 cm 140 equivalent feet 42 7 m diameter round duct should not exceed 140 equivalent Outside ventilation requires a HOOD EXHAUST DUCT feet 42 7 m Read the following carefully _ NOTE It is important that venting be installed using Elbows transitions wall and roof caps the most direct route and with as few elbows as possible etc present additional resistance to airflow and are This ensures clear venting of exhaust and helps prevent equivalent to a section of straight duct which is longer blockages Also make sure dampers swing freely and than their actual physical size When calculating the t
10. ape NOTES Bottom Edge of The space between the cabinets must be Cabinet Needs to i be 30 76 2 cm 30 76 2 cm wide and free of obstructions ki or More from the If the space between the cabinets is greater 164 41 3 cm Cooking Surface than 30 76 2 cm a Filler Panel Kit may be 30 76 2 cm used to fill in the gap between the microwave rem ne n oven and the cabinets Your Owner s Manual _ cm contains the kit number for your model es Backsplash This oven is for installation over ranges up to 36 91 4 cm wide 66 167 6 cm If you are going to vent your oven to the outside or Morefrom see Hood Exhaust Section for exhaust duct the Floor to the preparation Top of the oven Os When installing the oven beneath smooth flat cabinets be careful to follow the instructions on the top cabinet template for power cord clearance E The depth of the opening cannot be more than 13 1 2 34 3 cm Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE REMOVING THE OVEN FROM FINDING THE WALL STUDS THE CARTON REMOVING THE MOUNTING PLATE Remove the box containing the installation instructions filters exhaust adaptor damper and the small hardware bag Do not remove the Styrofoam protecting the front of the oven 2 Fold back all 4 carton flaps fully against carton sides Then carefully roll the oven and carton
11. at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet Cabinet Front SJ Cabinet Bottom Shelf j A Filler Block Equivalent to Depth of Cabinet Recess AULT lt Self Aligning Screw Oven Top Attach the oven to the top cabinet Installation Instructions MOUNT THE OVEN continued INSTALLING THE CHARCOAL FILTER Insert 2 selfaligning screws Remove 2 screws on top of oven just above the 4 28 x 3 4 through outer grille panel using a Phillips screwdriver Remove top cabinet holes Turn two one screw on the left side full turns on each screw Open the door Remove the grille LA LU f C CCCL Tighten center screw 2 28 x 2 completely Insert the filter into the oven as shown Tighten the outer two screws to the top of the maneuvering it behind the plastic grille until it fits oven While tightening screws hold the oven in squarely into place It will rest at an angle behind place against the wall and the top cabinet the plastic grille on two side support tabs and in front of the right rear tab When properly installed the w
12. ate Finding the Wall Studs Determining Wall Plate Location Aligning the Wall Plate Installation Types A Outside Top Exhaust Attach Mounting Plate to Wall Preparation of Top Cabinet Checking for Proper Damper Operation Mount the Microwave Oven Adjust the Exhaust Adaptor Connecting Ductwork B Outside Back Exhaust Preparing Rear Wall for Outside Back Exhaust Attach Mounting Plate to Wall Preparation of Top Cabinet Adapting Blower for Outside Back Exhaust Mount the Oven Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three prong grounded outlet The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded If not properly grounded or if the outlet box does not meet electrical requirements noted under ELECTRICAL REQUIREMENTS a qualified electrician should be employed to correct any deficiencies CAUTION For personal safety remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury CAUTION For personal safety the mounting surface must be capable of supporting the cabinet load in addition to the added weight of this 63 85 pound 28 5 38 5 kg product plus additional oven loads of up to 50 pounds 22 7 kg or a total weight of 113 135 pounds 51 3
13. ing installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from over tightening screws NOTE When mounting the oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord EN Lift oven tilt it forward and hook slots at back bottom edge onto two lower tabs of mounting plate N Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet 18 Cabinet Front JS Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self Aligning Screw Oven Top Attach the oven to the top cabinet 5 Insert 2 self aligning screws 2 28 x 3 through outer top cabinet holes Turn two full turns on each screw Tia Tighten center screw 4 28 x 2 completely Tigh
14. ire mesh of the filter should be visible from the front Aaa LLLLLLL LODO LLL TTA WLLL z UIIE LLL E LZ Ze xe A 4 tim SZ Install grease filters See the Owner s Manual packed with the oven Replace the grille and the 2 top screws Close the door and replace left side screw Insert mesh side down 22 Installation Instructions BEFORE YOU USE YOUR MICROWAVE Make sure the oven has been installed Read the Owner s Manual according to instructions KEEP INSTALLATION INSTRUCTIONS 2 Remove all packing material from the oven FOR THE LOCAL INSPECTOR S USE 3 Install turntable and wheeled ring in cavity Replace house fuse or turn breaker back on Plug power cord into a dedicated 15 to 20 amp electrical outlet Ensure proper ground exists before use 23 49 40453 06 05 JR 24 Printed in Korea
15. llowing the instructions of the REAR WALL TEMPLATE 15 ATTACH THE MOUNTING PLATE TO THE WALL 0 C g 99 20 0 Og o o 0 OO Sam Tks 0000 OSs a Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud Remove the toggle wings from the bolts Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 4 2 cm onto each bolt Installation Instructions To use toggle bolts Spacing for Toggles More gt i lt Than Wall Thickness Toggle Wings Mounting ee i i Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the
16. ock Damper 7 Equivalent to Depth of Cabinet Recess z Back of oven EU Self Aligning Screw l r Oven Top Attach the oven to the top cabinet Insert 2 self aligning screws 4 28 x 3 through outer top cabinet holes Turn two CONNECTING DUCTWORK full turns on each screw House Duct Tighten center screw 4 28 x 2 completely Tighten the outer two screws to the top of the oven While tightening screws hold the oven in Extend the house duct down to connect to place against the wall and the top cabinet the exhaust adaptor Seal exhaust duct joints using duct tape Install grease filters See the Owner s Manual packed with the oven 14 Installation Instructions OUTSIDE BACK EXHAUST Horizontal Duct INSTALLATION OVERVIEW B1 Prepare Rear Wall B2 Attach Mounting Plate to Wall B3 Prepare Top Cabinet B4 Adjust Blower B5 Mount the Oven PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust Read the instructions on the REAR WALL TEMPLATE Tape it to the rear wall lining up with the holes previously drilled for holes A and B in the wall plate Cut the opening fo
17. otal nothing is blocking the ducts duct length add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections Exhaust connection The chart below shows you how to calculate total The hood exhaust has been designed to mate with equivalent ductwork length using the approximate feet a standard 3 x 10 8 2 x 25 4 cm rectangular duct of equivalent length of some typical ducts Ifa round duct is required a rectangular to round transition adaptor must be used Do not use less than a 6 15 2 cm diameter duct EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH Rectangular to Round 5 Ft 1 5 m Transition Adaptor IP Wall Cap 40 Ft 12 2 m Ft or m Straight Duct 6 15 2 cm 1 Ft 0 3 m Ft or m Round or 3 x 10 8 2 x 25 4 cm Rectangular IMPORTANT If a rectangular to round transition Equivalent lengths of duct pieces are based on actual tests gt adaptor is used the bottom corners of the damper and reflect requirements for good venting performance with will have to be cut to fit using the tin snips in order any vent hood to allow free movement of the damper Installation Instructions DAMAGE SHIPMENT PARTS INCLUDED INSTALLATION ADDITIONAL PARTS If the unit is damaged in shipment return the PART QUANTITY unit to the store in which it was bought for repair or replacement If the unit is damaged by the customer repair or TOP CABIN
18. rflow to exhaust out the rear of the oven CAUTION Be sure to trim the sharp edges from the openings after removing the knockout plates Oven Rear Panel Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow Place the blower unit back into the opening AFTER Fan Blade Openings End A Facing Back End B gt unit wiring Make sure the wires are not pinched NOTE The blower unit exhaust openings should match exhaust openings on rear of oven 17 Replace the blower plate in the same position as before with the screws Blower Plate Screws Blower Plate Back of Oven the holes at the inside rear of the adaptor Exhaust Adaptor Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven Damper Exhaust Adapt xhaust Adaptor hinge side up Slide exhaust adaptor into guides on oven rear Guides Push in securely until it is in the lower locking tabs Take care to assure the damper hinge is installed so that it is at the top and that the damper swings freely Secure the exhaust adaptor to the oven with the two bronze metal screws provided Installation Instructions MOUNT THE MICROWAVE FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN IMPORTANT Do not grip or use handle dur
19. stallation Instructions ADAPTING BLOWER FOR RECIRCULATION continued Place the blower unit back into the opening CAUTION Do not pull or stretch the blower unit wiring Make sure the wires are not pinched Secure blower unit to oven with the screw removed in Step 2 Insert the screw in bottom right screw hole on the back of the oven Replace blower plate with the screws removed in Step 1 f lt Blower Plate Screws Al Back of Oven ag Blower Motor Screw FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from over tightening screws NOTE When mounting the oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord Lift oven tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting Rotate front of oven up against cabinet bottom Insert a selfaligning screw through top center cabinet hole Temporarily secure the oven by turning the screw
20. t rating The power supply cord and plug should be brought to a separate 15 to 20 ampere branch circuit single grounded outlet The outlet box should be located in the cabinet above the oven The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code Installation Instructions HOOD EXHAUST NOTE Read these next two pages only if you plan to vent your exhaust to the outside If you plan to recirculate the air back into the room proceed to page 6 OUTSIDE TOP EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH Roof Cap 24 Ft 7 3 m 24 Ft 7 3 m 12 Ft 3 6 m Straight Duct 12 Ft 3 6 m 12 Ft 3 6 m 6 15 2 cm Round A Rectangular to Round 5 Ft 1 5 m 5 Ft 1 5 m Transition Adaptor Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Total Length IMPORTANT If a rectangular to round transition adaptor is used the bottom corners of the damper will have to be cut to fit using the tin snips in order to allow free movement of the damper OUTSIDE BACK EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH
21. t with front overhang Mounting Plate with Tabs Below Cabinet Bottom the Same Distance as the Front Overhang Depth 30 76 2 cm to Cooktop Y Plate position beneath framed recessed cabinet bottom Mounting Plate Tabs Touching the Back Frame 130 76 2 cm to Cooktop Your cabinets may have decorative trim that interferes with the oven installation Remove the decorative trim to install the oven properly and to make it level THE OVEN MUST BE LEVEL Use a level to make sure the cabinet bottom is level If the cabinets have a front overhang only with no back or side frame install the mounting plate down the same distance as the front overhang depth This will keep the oven level Measure the inside depth of the front overhang Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang For this type of installation with front overhang only align the mounting tabs with this horizontal line not touching the cabinet bottom as described in Step D Installation Instructions ALIGNING THE WALL PLATE Hole C CAUTION Wear gloves to avoid cutting fingers on sharp edges 1 2 Draw a vertical line on the wall at the center of the 30 76 2 cm wide space Use the mounting plate as the template for the rear wall Place the mounting plate on the wall making sure that the tabs are touching the bot
22. ten the outer two screws to the top of the oven While tightening screws hold the oven in place against the wall and the top cabinet Install grease filters See the Owner s Manual packed with the oven Installation Instructions RECIRCULATING Non Vented Ductless INSTALLATION OVERVIEW C1 Attach Mounting Plate to Wall C2 Prepare Top Cabinet C3 Adjust Blower C4 Mount the Oven C5 Install Charcoal Filter not supplied ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3 4 2 cm onto each bolt To use toggle bolts Spacing for Toggles More Than Wall gt lt lt Thickness Toggle Wings Mounting wl j Toggle Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers bet
23. tom of the cabinet or the level line drawn in Step C for cabinets with front overhang Line up the notch and center line on the mounting plate to the center line on the wall While holding the mounting plate with one hand 3 draw circles on the wall at holes A B C and D see illustration above actual plate marked with arrows Four holes must be used for mounting Draw a Vertical Line on Wall lt lt from Center of 10 Top Cabinet NOTE Holes C and D are inside area E If neither C nor D is in a stud find a stud somewhere in area E and draw a fifth circle to line up with the stud It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave Set the mounting plate aside Drill holes on the circles If there is a stud drill a 6 hole for wood screws For holes that don t line up with a stud drill a 3 hole for toggle bolts NOTE DO NOT MOUNT THE PLATE AT THIS TIME Installation Instructions 2 INSTALLATION TYPES choose A B or C This oven is designed for adaptation to the following NOTE This oven is shipped assembled for Outside Top 3 types of ventilation Exhaust Select the type of ventilation required for your A Outside Top Exhaust Vertical Duct installation and proceed to that section B Outside Back Exhaust Horizontal Duct C Recirculating Non Vented Ductless OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST VERTICAL
24. ween the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom Installation Instructions ADAPTING BLOWER Carefully pull out the blower unit The wires FOR RECIRCULATION will extend far enough to allow you to adjust the blower unit NOTE The exhaust adaptor with damper is not needed for recirculating models You may want to save them for possible future use Remove and save screws that hold blower plate to the oven v lt Blower Plate Screws 4 Roll the blower unit 90 so that fan blade openings are facing toward the front of the oven BEFORE Fan Blade Openings Facing Up Slide the blower plate from under its retaining flange and lift it off Remove and save screw that holds the blower motor to oven Retaining Blower Motor Screw AFTER Fan Blade Openings Facing Forward NOTE Make sure wires remain routed in the grooves of the motor frame 20 In
Download Pdf Manuals
Related Search