Garmin zumo 665, NA Installation Instructions
Contents
1. can cause brake or clutch malfunction which can result in damage to the vehicle and the risk of personal injury or death Garmin strongly recommends having an experienced installer with the proper knowledge of clutch brake systems install the unit NOTE Both 1 4 in standard and M6 bolts are included Match the size of the factory bolts on your clutch brake clamp bracket 1 Remove the two factory bolts on your clutch brake clamp bracket 2 Thread the new bolts through the handlebar base spacers and clamp bracket 3 Tighten the bolts to secure the base Handlebar base Clutch brake clamp bracket Spacers Step 3 Attaching the Base Plate to the zumo Mount 1 Thread the M4 x 40 mm panhead screws through the washers cradle spacers and base plate 2 Tighten the nuts to secure the base plate _ Cradle Panhead screws a Base plate iie Nuts ee Noes Ri 4 Attaching the Base Plate to the Handlebar Base Align the ball of the handlebar base and the ball of the base plate with the double socket arm Base plate 2 Tighten the knob slightly 3 Adjust for better viewing and operation Cradle 4 Tighten the knob to secure the mount Double socket Step 5 Installing Your zumo in the Mount 1 Fit the bottom of your z mo into the cradle 2 Tilt the z mo back until it snaps into place Cradle E Release button Removing Your z mo from Either Mount 1 Press the button on the side of the2. lace the suction cup on the windshield 4 Flip the lever back toward the windshield Suction cup mount 5 Snap the cradle onto the suction cup arm 6 Fit the bottom of your z mo into the cradle 7 Tilt the z mo back until it snaps into place 8 Plug the other end of the automotive power cable into a power outlet Connecting the GXM 40 Antenna to the Automotive Mount 1 With the zumo placed in the cradle plug the GXM 40 antenna into the mini USB port on the back of the automotive mount Mini USB port GXM 40 2 Place the GXM 40 antenna within clear view of the sky 2010 Garmin Ltd or its subsidiaries www garmin com Garmin and z mo are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries These trademarks may not be used without the express permission of Garmin Other trademarks and trade names are those of their respective owners January 2010 Part Number 190 01145 02 Rev A Printed in Taiwan
3. mount to release the z mo 2 Lift out the z mo 3 Place the weather cap on the cradle motorcycle mount only Connecting the GXM 40 Antenna NOTICE Do not place the GXM 40 antenna on the fuel tank or in any location where it may come into contact with fuel or excessive heat gt With the z mo placed in the motorcycle mount remove the weather cap from the mini USB connector on the Power cable Plug the GXM 40 antenna into the mini USB connector Place the GXM 40 antenna within clear view of the sky in an area where there is at least 10 cm between the antenna and your zUmo For best performance place the GXM 40 antenna at least 30 cm away from the z mo O N NOTE The GXM 40 antenna can also be placed in an area covered by a non conductive material such as a fiberglass top case tank bag or leather saddlebag Mounting Your z mo in an Automobile See the Important Safety and Product Information guide in the product box for product warnings and other important information This product contains a lithium ion battery To prevent damage remove the unit from the vehicle when exiting or store it out of direct sunlight 1 Plug the automotive power cable into the connector on the right side of the cradle Release button Automotive Cradle power cable Microphone jack 2 5 mm 2 Remove the clear plastic from the suction cup Clean and dry your windshield and the suction cup with a lint free cloth 3 P
4. zumo 665 Installation Instructions Incorrectly wiring the power cable with bare wire leads can result in damage to the vehicle or the battery and can cause bodily injury Garmin strongly recommends having an experienced installer with the proper knowledge of electrical systems install the unit See the mportant Safety and Product Information guide in the product box for product warnings and other important information Do not use the suction cup mount on a motorcycle Step 1 Connecting Power to the Mount Select a suitable and secure location to mount the zimo on your motorcycle based on available power sources and safe cable routing Headphone audio out jack 3 5 mm Cradle Bare wires with inline fuse for power connection Power cable Microphone jack 2 5 mm MEUSE comedor for GXM 40 Antenna Step 2 Installing the Handlebar Base NOTICE The recommended torque is 50 Ibf in Do not exceed torque of 80 lbf in The z mo includes parts for two handlebar installation solutions Custom mounts can require additional hardware www ram mount com Option A Installing the U bolt and Handlebar Base 1 Place the U bolt around the handlebar and thread the ends through the handlebar base 2 Tighten the nuts to secure the base Do not overtighten Handlebar base U bolt Option B Installing the Handlebar Base to the Clutch Brake Clamp Bracket Incorrectly installing the handlebar base to the clutch brake bracket
Download Pdf Manuals
Related Search