Garmin TR-1 Instruction Manual
Contents
1. A GARMIN TR 1 Gold Cylinder and Bracket Mounting Instructions Yamaha F 15 HP 1998 2006 Yamaha F 9 9 2003 and Newer Yamaha T 9 9 2005 2007 Except 2007 Canadian T9 9 Bee PN 906 1080 00 Parts Cylinder Kit PN 120 0900 00 e uo iam pr P DT ar B ox A Tal d _ ss k e ee Ser LES mmm eme Cylinder Mounting Kit PN 120 1080 00 I Nau I A A EK m ENLTLL QTY AL 130008402 U Botl13 4IDl1 4A20 4 231000725 J LW Spliti 4 5 33010100 Pin Stern Pivot 6 310250125 J ClevsPin A4DX125 8 330 1081 01 Standoff Fro 9 310006702 HairPinCoterMedium 330 1002 00 Rod Eye 5 16 24 310 0042 09 Hex Jam Nut 5 16 24 UNF SS Thin 340 0900 00 Cylinder 321 0001 00 Fitting Straight 1 8 NPT X 1 4 Cylinder Tail Bushing Page 2 0042 0000 0001 0040 0901 0001 Figure 3 Step One Remove the Three 3 Bolts as shown in Figure 1 Two Bolts on top and the RT side Bottom Hang onto them for the next step Step Two Insert bolts from the starboard side as shown in Figure 2 Thread the Standoffs onto the Bolts Item 8 goes on the front top threads Item 7 goes on the back top and bottom Use a thread locking com pound such as Loctite on all bolt threads Step Three Fasten the Channel item 2 with the 3 bolts item 12 into the standoffs Tighten bolts securely Fi2. gure 5 Page 4 Step Four Locate the rod eye bracket item 1 One 1 inch up on the Shock mount shroud above the cylinder Channel as shown in Figure 4 Step Five Insert U Bolt item 4 through the Rod eye Bracket and secure with washers item 4 and Nuts It s recommended to use Loctite or similar compound to secure nuts Step Six Insert the Stern Pivot Pin through the back eye end of the cylinder and through the channel Fig A Use a small cotter pin through the hole on the bottom of the stern pivot pin Fig B This will keep the pin from coming back out channel Inset the Clevis pin into the top of the Stern pivot pin through the rear eye of cylinder Fig C and line up the hole in the stern pivot pin and the clevis pin and insert the large cotter pin to hold in place Fig D 8 E RK amp EA E t bd s H ib m L H 1 d Co Ta Ar 4 P WT D U T A Y age Ze Q Page 5 Step Seven Attach the Rod eye end of the cylinder to the vertical pin on the Rod eye Bracket using the plastic washer to take up slack on pin Insert the cotter pin through the hole in the vertical pin on the rod eye bracket as shown in Picture Turn the motor hard over to starboard That will retract the cylinder rod into the cylinder Check that the cylinder rod 1s still free to re tract at least a little more Next turn the motor hard over to port That will extend the cylin der r
3. od out of the cylinder Check that the cyl inder rod is still free to extend at least a little more It should have additional travel in both directions If it does not adjust the position of the rod eye on the cylinder shaft The cylinder shaft should turn with your fingers if the Hex Jam Nut is loose If the shaft does not turn freely enough use a thin 1 4 inch open end wrench at the shaft s wrench flats Do not use any tool on the cylindrical part of the cylin der shaft If the shaft gets scratched bent or dinged the seal will fail With the cylinder properly adjusted secure it by tightening the Hex Jam Nut against the Rod Eye Be sure to use a Thread locker compound Loctite or similar on the threads to prevent the jam nut item 33 and Rod Eye item 31 from backing out Page 6
Download Pdf Manuals
Related Search