Fujifilm QP242 User's Manual
Contents
1. 35 Ending a Job 36 Emptying the Reject Bin 38 Emptying Cover Tape 39 Shutting Down 40 Restarting a Job 42 Operation Chapter 4 34 ProLINE RoadRunner Operator s Guide A To run a job 1 Insert a job card into the PCMCIA card slot 2 Clear the conveyor belt of any unneeded devices 3 Press Start The green lamp will start blinking When the programmed devices reach the assembly machine pick point the belt will pause and the green lamp will stay lit without blinking Running a Job 3 gt Job Advance Pocket Align Pocket Purge 1 35 ProLINE RoadRunner Operator s Guide A To pause at the end of the current operation 1 Press Pause on the control panel To instantly stop in an emergency situation 2 Press the Emergency Stop E Stop button The E Stop does not stop the assembly machine Pausing or Stopping a Job 1 gt Job Advance Pocket Align Pocket 2 gt Job Advance Pocket Align Pocket Warning Electrical shock hazard The E Stop does not stop electricity to RoadRunner 36 ProLINE RoadRunner Operator s Guide A Whenever you are going to change job cards you must first end the current job To end the current job 1 Press Pause button 2 Select End from the Job Menu Job is in the main menu The system will finish processing devices and place the devices on the belt bu2. E mail support dataio com You can also find answers by visiting the Knowledge Base on our Web site at www dataio com then click Support then Knowledge Base Search Contact your local Data I O representative To find your local representative go to http www dataio com contact repsearch asp Technical Support
3. ProLINE RoadRunner Operator s Guide A Inserting a Job Card 20 Changing the Precisor 22 Changing the Actuator Plate 24 Changing the Socket Adapter 26 Adjusting the Tape In Module 28 Loading a Reel of Devices 30 Aligning the Tape Pockets 32 Job Setup Chapter 3 20 ProLINE RoadRunner Operator s Guide To run a job insert a TaskLink job card into the PCMCIA card slot Use only TYPE I or TYPE II PCMCIA cards To insert a job card 1 If the power switch is on make sure the blue lamp is lit Inserting a Job Card Electrostatic discharge may cause damage Discharge static against common ground prior to inserting Job Card Caution 1 ProLINE RoadRunner Data I O Corporation Version 02 00 00 B 21 ProLINE RoadRunner Operator s Guide A 2 Slide the job card into the PCMCIA card slot NOTE When fully inserted the job card extends slightly from the PCMCIA card slot NOTE Do not eject the card unless the blue lamp is lit or the power is off 3 The Card Eject button can be pushed to remove the card when the blue lamp is lit 2 3 22 ProLINE RoadRunner Operator s Guide To change the precisor 1 Select Job then End wait for the blue lamp to light and turn the power Off 0 2 Lift off the Robotics Cover 3 Starting at one end pull the precisor down off the magnet and then pull the other end off The PNP Head Cover
4. air hose behind the quick connect collar and push it firmly onto the male fitting The collar must be allowed to move back as it goes onto the fitting NOTE Compressed air must be clean and dry at approximately 5 25 kgf cm2 75 psi Connecting Power and Air 2 1 Warning Point air hoses away from body Wear approved eye protection 17 ProLINE RoadRunner Operator s Guide A 3 Connect to a grounded power source using a cable with a standard IEC 320 plug RoadRunner accepts power between 100 and 240 VAC 50 60Hz 4 Align and push the communications cable end into the RoadRunner connector The other end should already be connected to the MFU NOTE To disconnect the air hose grasp the collar on the connector and pull back The air line is equipped with a quick connect that will stop airflow when disconnected Pull Collar 3 4 18 ProLINE RoadRunner Operator s Guide A To run the Self Test 1 Turn the power switch On I All the control panel indicator lamps light up When the Self Test finishes the blue lamp will remain on and the version number will display If all the indicator lamps start blinking a serious error has occurred Turn the unit off then on again If the error continues have the unit serviced 2 If no errors display RoadRunner is operation ready Running the Self Test 1 ProLINE RoadRunner Data I O Corporation Version 05 14 00 C 19
5. will appear in the keypad display 2 Check the condition tape path Reject Bin etc implied by the message If you cannot correct the error condition contact a service technician 3 Press Menu to remove the message If there are other error messages the next one will appear 1 Inadequate Air Pressure 3 gt U8 RevA ID27 Devices 800 Rejected 0 Parts Hr 567 49 ProLINE RoadRunner Operator s Guide A Stop Caution Motor Controller not responding Some common error messages are listed below For more information see Troubleshooting in the ProLINE RoadRunner Owner s Manual 1Twist the Emergency Stop button to release it Lamp Color Error Message No change in lamps Card not present Yellow Reject Bin needs to be emptied Blue Cover tape broken Blue Emergency Stop is activated1 Blue Motor controller not responding 50 ProLINE RoadRunner Operator s Guide A If a socket repeatedly becomes disabled RoadRunner should be serviced To re enable a disabled socket 1 Select Socket from the top level menu 2 Arrow down and select the disabled socket from the Socket menu A dot appears 3 Press the Up Arrow button to re enable the socket NOTE To disable a probe disable the probe s corresponding socket Enabling a Socket 1 Advance Pocket Align Pocket Purge gt Socket 3 Socket 1 Disabled Socket 2 Enabled Socket 3 Enabled Soc
6. ProLINE RoadRunner English PN 096 0230 002 Operator s Guide for Fuji MFU QP242 QP351 IP3 CONTENTS Overview Installation Job Setup Operation Maintenance Troubleshooting Data I O has made a conscientious effort to ensure that the information in this document is accurate and complete Data I O assumes no liability for errors or for any incidental consequential indirect or special damages including without limitation loss of use loss or alteration of data delays or lost profits or savings arising from the use of this document or the product which it accompanies No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without written permission from Data I O Data I O is a registered trademark of Data I O Corporation TaskLink is a trademark of Data I O Corporation ProLINE RoadRunner is a trademark of Data I O Corporation Data I O Corporation acknowledges the trademarks of other organizations for their respective products or services mentioned in this document 2005 Data I O Corporation All rights reserved No rotate 1 ProLINE RoadRunner Operator s Guide A ProLINE RoadRunner for Fuji 2 Jobs and Statistics 3 External View 4 Internal Components 5 Control Panel Lights 6 Control Panel Buttons 7 Operator Menus 8 Supervi
7. ave no effect Job is the first item in the main menu NOTE To change languages press Menu while pressing the Select button Arrow Down to the desired language and press Menu twice Version 5 14 00 menus shown Operator Menus Socket Socket 1 Enabled Socket 2 Enabled Socket 3 Enabled Socket 4 Enabled Adapter Statistics Reset Clean Clean Count Clean Alert 3500 No 22113204 Mfg 09 23 02 Actuations 1055 Adptr Life 10000 Insertions 4220 Pass 4202 Fail 16 Yld 99 5 Socket 1 Insertions 1055 Pass 1053 Fail 2 Yield 99 8 Socket 2 same as 1 Socket 3 same as 1 Socket 4 same as 1 Job View Job Name Device E28F320 Checksum 3FC00000 Mfg INTEL Adapter PA G021 Prec 621 0086 005 Act 644 0016 001 Results Passed 992 Failed 4 System Yld 98 7 Prgrmr Yld 99 6 Handler Yld 99 5 Parts Hour 255 MCBI 201 Skt 1 Yld 99 9 Skt 2 Yld 100 Skt 3 Yld 100 Skt 4 Yld 100 Skt Cycles 249 End Light gray shaded fields cannot be changed For Advance Pocket Align Pocket and Purge see Chapter 3 in the Owner s Manual Main Menu Job Advance Pocket Align Pocket Purge Socket 9 ProLINE RoadRunner Operator s Guide A View the Supervisor Menus by inserting a PCMCIA card with supervisor authority The menus on this page and the next two pages are in addition to the Operator Menus Supervisor Administrator authorization is set in TaskLink For more information
8. b from the Job Menu and wait for all devices to be placed on the belt 3 Turn the power Off 0 4 Remove devices from the conveyor belt Shutting Down 1 gt Job Advance Pocket Align Pocket Purge 3 Reel not shown 41 ProLINE RoadRunner Operator s Guide A 5 Empty the Reject Bin 6 Remove and empty the Take Up Reel For more see the previous heading 7 Remove the air hose or shut off the air flow NOTE When disconnecting the air hose pull the connector collar back as you pull the connector off 5 6 42 ProLINE RoadRunner Operator s Guide A To restart RoadRunner after a pause or an emergency stop 1 Turn the Emergency Stop button clockwise to release it if needed 2 Press Menu until the main level menu is displayed 3 Select Align Pocket 4 Press the Up Arrow to advance the device tape until the next pocket center hole lines up with the alignment mark 5 Press Start The job will resume 1 Job Advance Pocket gt Align Pocket Purge 3 Restarting a Job 4 5 43 ProLINE RoadRunner Operator s Guide A Cleaning with Air 44 Cleaning with Alcohol 45 Running the Self Test 46 Maintenance Chapter 5 44 ProLINE RoadRunner Operator s Guide A To prevent dust accumulation inject compressed air into the following component areas 1 Tape In Module weekly 2 Sockets daily Sockets should be op
9. can be removed for easier access Changing the Precisor 3 PNP Head Cover 3 Pinch Warning Keep hands away from moving parts Warning 23 ProLINE RoadRunner Operator s Guide A 4 When inserting the new precisor make sure that the part number faces up and that the small holes near the precisor edge fit over the dowel pins on the PNP head There should be no visible gap between the precisor and the head 4 24 ProLINE RoadRunner Operator s Guide To change the Actuator Plate 1 Select Job then End wait for the blue lamp to light and turn the power Off 0 2 Lift off the Robotics Cover Once power is off the PNP Head can be moved by hand to allow access to the Actuator Plate PNP Head Changing the Actuator Plate Warning Pinch Warning Keep hands away from moving parts 25 ProLINE RoadRunner Operator s Guide A 3 Pull the Actuator Plate to slide it out of the grooved brackets NOTE The Actuator Plate must be out to access or change the Socket Adapter To change the Socket Adapter see the procedure on the following page 3 26 ProLINE RoadRunner Operator s Guide To change the Socket Adapter with the Actuator Plate removed 1 Make sure the power is Off 0 2 Unscrew the two captive screws and lift the adapter bracket 2 2 Changing the Socket Adapter Caution Electrostatic Discharge may cause damage Discharge static against common gro
10. easure Device Offset 0 00 Sensors Tape Sprocket 0 Tape Broken 0 Reject Full 0 Reject Bin 1 Air 1 Interlock 0 E Stop 0 Overtravel 0 Home 1 Socket State Up Actuate 0 Act Duration 1501 Probe 1 4 Position Up Vacuum Enabled Puff Enabled Vac Sense 1 Speed 135 5 Head Position Head 0 Light gray shaded fields cannot be changed Programmer Diags Programr Enabled Exercise Display Test Cycles 3 Test All PASS Bus Test PASS Adtr ID Test PASS LED Dvr Test PASS G Node Test PASS Vcc OC Test PASS Vpp OC Test PASS I2C Bus Test PASS DAC Ref Test PASS GSlew Test PASS High RAM Test Continuity Loop 3 Event Log View Clear Programmer Diagnostic tests require a Diagnostic Adapter Board for all items below this line Supervisor Menus continued 12 ProLINE RoadRunner Operator s Guide A Warnings and Cautions Compressed Air Point air hoses away from body Always wear approved eye protection Loud Noise Sound pressure levels may exceed 85db Hearing protection is recommended for prolonged exposure at this level High Voltage Turn power off before removing electronics cover Heavy Object This equipment weighs approximately 15Kg 35 lbs Do not drop Mount only with approved hardware Moving Parts Pinch warning Keep hands away from moving parts Electrostatic Discharge Electrostatic Discharge ESD may cause damage Discharge static against a common
11. ened and closed by hand while air is injected NOTE Compressed air must be clean and dry Cleaning with Air 1 2 Warning Point Air Hoses Away From Body Wear Approved Eye Protection 45 ProLINE RoadRunner Operator s Guide A To prevent dust and oil accumulations clean the following component areas with isopropyl alcohol on a lint free cloth Chassis and Covers every 3 months Conveyor belt daily See Device Rotation in the Troubleshooting chapter NOTE Dry the conveyor belt before rotating it These intervals are based on running 40 000 devices weekly Cleaning with Alcohol 46 ProLINE RoadRunner Operator s Guide A Run the Self Test procedure approximately once a week To run the Self Test procedure 1 Press Pause 2 Clear all devices from the sockets and from the conveyor belt 3 Toggle the power switch off and then back on The Self Test will run checking the condition of the components 4 Check the display for system errors Running the Self Test 1 gt Job Advance Pocket Align Pocket 3 47 ProLINE RoadRunner Operator s Guide A Viewing Errors 48 Enabling a Socket 50 Clearing Jammed Tape 51 Device Rotation 52 Technical Support 53 Troubleshooting Chapter 6 48 ProLINE RoadRunner Operator s Guide A Viewing Errors To view and correct errors 1 Messages
12. ground 13 ProLINE RoadRunner Operator s Guide A Mounting on the Feeder Bank 14 Connecting Power and Air 16 Running the Self Test 18 Installation Chapter 2 14 ProLINE RoadRunner Operator s Guide A To mount RoadRunner onto an MFU 1 Align and push the communica tions cable into the MFU NOTE To allows access to RoadRunner do not use the ten right most slot positions on the MFU 2 While holding RoadRunner at a slight nose down angle let the nose rest on the MFU Ensure that it settles into a slot Mounting on the Feeder Bank 1 Heavy 15 kg 31 lb Do not drop Mount only on approved units Warning 3 2 15 ProLINE RoadRunner Operator s Guide A 3 Still holding it at an angle slide it forward as far as it will go The nose will fit under the lip on the MFU 4 Lower RoadRunner and jiggle it to ensure that the angle bracket has settled into the spring clamp on the MFU NOTE The assembly machine pick point will correspond with the MFU slot number that is inline with the conveyor belt Make sure the communication socket number corresponds with that slot number 4 Warning Heavy 15 kg Do not drop Turn off RoadRunner and disconnect facilities before removing it from a feeder bank 16 ProLINE RoadRunner Operator s Guide A To connect the power and the air 1 Turn the RoadRunner power switch to the Off 0 position 2 Grasp the
13. ket 4 Enabled 2 51 ProLINE RoadRunner Operator s Guide A If the tape jams an error message displays and the blue lamp illuminates To clear the tape path 1 Press the Emergency Stop button to continue the job later or select Job then End Turn the power off 2 Unroll one turn of cover tape and cut it near the Take Up Reel 3 Cut the device tape where it exits the conveyor 4 At the tape reel pull the tape out backwards until the end is free from the tape path 5 Trim away any flaws before reloading 2 2 Cut Cvr 4 Clearing Jammed Tape Cut Tape 3 52 ProLINE RoadRunner Operator s Guide A Device Rotation If devices rotate excessively on the conveyor belt 1 Press Pause Wait for all the devices to get picked from the belt 2 Press the Emergency Stop 3 Remove the Dust Cover and clean only the exposed surface of the conveyor belt with isopropyl alcohol on a lint free cloth then dry it Rotate the belt by hand and repeat until clean 4 To continue replace the Conveyor Dust Cover release the Emergency Stop button and press Start 3 Clean Dry Rotate Belt Repeat 53 ProLINE RoadRunner Operator s Guide A Worldwide Data I O Corporation Shipping address 10525 Willows Road N E Redmond WA USA 98052 Mailing address P O Box 97046 Redmond WA USA 98073 9746 Telephone 425 867 6870 USA Only 1 800 332 8246 Fax 425 882 1043
14. n the spindle end 3 Insert the device tape into the Tape In Module and onto the sprocket 4 Select Advance Pocket from the operator menu then press the Up Arrow button 2 Loading a Reel of Devices 4 3 31 ProLINE RoadRunner Operator s Guide A 5 When the tape is advanced past the Peel Bar separate the cover tape from the device tape 6 Thread the cover tape up through the cover tape path and attach it to the Cover Tape Take Up Reel Advance the tape as necessary NOTE A small piece of adhesive tape may be needed to stick the cover tape to the Take Up Reel 7 Turn the Take Up Reel to take up slack cover tape 8 Align the tape pockets as described in the following procedure 5 7 6 6 32 ProLINE RoadRunner Operator s Guide To align the tape pockets 1 Select Align Pocket from the Operator Menu 2 Press the Up Arrow button to advance the tape until the next tape pocket center hole is approximately centered at the pick point alignment mark Do not advance devices past the pick point They may fall and jam the tape path Do not use the Down Arrow to align NOTE This aligning procedure must be performed each time power is applied such as after releasing the Emergency Stop Aligning the Tape Pockets 1 Job Advance Pocket gt Align Pocket Purge 2 2 33 ProLINE RoadRunner Operator s Guide A Running a Job 34 Pausing or Stopping a Job
15. p e r a t i o n Job Pick Retries 2 Error Retries 3 Pocket Pitch 4 Pocket Advance 3 Head Velocity 250 Accel 700 Probes Puff 50 Pick 200 Place 100 Travel 250 Teach Tape 40 0 Skt 1 26 85 Reject 166 Belt 180 Restore Defaults System Time Hour 4 Minute 55 Month 9 Day 23 Year 2002 Odome ter Hours 469 92 Devices 24742 Timekeeping OFF Erase 0 0s Blankcheck 0 0s Program 0 0s Verify 0 0s Update Software Network Network Parm Card Status Enabled PGM Fred sRR2 IP 888 888 88 888 Prog Port 7596 SUB 255 255 248 GTW 139 138 16 1 SNS 0 0 0 0 Network cont SNS Port 7500 HST rr215 nt data io DOM nt data io com DNS 888 888 88 888 DTS 888 888 88 88 EAddr 0010EC002211 Clear NetParms Configu ration Firmware Version Ver 05 11 00 C Installed Boards Bkpln Brd Id 2 Cntrl Brd Id 1 Wvfrm Brd Id 1 Adptr Brd Id 3 Hardware Config HwCfgIds 1 3 4 Model name uC System Supervisor Menus continued 11 ProLINE RoadRunner Operator s Guide A Refer to the main Supervisor Menu 2 pages back for orientation NOTE Programmer Diags are only available with a Diagnostic Adapter Board 1 Actuation duration is set by the Socket Adapter For more information about menu commands see Chapter 3 of the ProLINE RoadRunner Owner s Manual Robot Diags Robot Enabled Run Mode Job Dry Run Belt Move Fwd Bkw Pick Sensor 0 Speed 400 10 M
16. r s Guide A 1 Cover Tape Take Up Reel 2 Tape In Module 3 PNP Probes Precisor and Cover 4 Reject Bin 5 Socket Adapter Actuator Plate and Programmer 3 1 2 4 5 Internal Components 6 ProLINE RoadRunner Operator s Guide A Control Panel Lights 1 Blue Stop Indicator User intervention is required or the unit is paused Do not remove PCMCIA card unless blue lamp is lit 2 Yellow Caution Indicator Correct a problem or the machine will stop 3 Green Run Indicator Lit A job is running Blinking Programmed devices are not yet at the SMT pick point 4 Emergency Stop Press to stop the robot motors in an emergency To resume motion twist the button and press Start 1 2 3 4 7 ProLINE RoadRunner Operator s Guide A 1 Start start or resume the chosen job 2 Menu exit to the previous menu or show the next message deleting the current one or deselect an item 3 Up and Down Arrows move through menu items 4 Select select menu items 5 Pause interrupt the job without cancelling it Control Panel Buttons 3 1 4 2 5 8 ProLINE RoadRunner Operator s Guide A Operator Menus are visible on the RoadRunner control panel and can be navigated by using the Up Arrow and Down Arrow buttons Pressing the Menu button displays the menu that is one level up If you are at the main menu pressing Menu will h
17. refer to the TaskLink Help Menu Version 5 14 00 menus shown A indicates the currently selected item A indicates the current cursor position See next page Next odd page HOME sends the PNP Head to the Home position Light gray shaded fields cannot be changed Main Menu Job Advance Pocket Align Pocket Purge Socket Home Operation System Robot Diagnostics Programmer Diags Event Log Job View Job Name Device E28F320 Checksum 3FC00000 Mfg INTEL Adapter PA G021 Prec 621 0086 005 Act 644 0016 001 Results Passed 992 Failed 4 System Yld 98 7 Prgrmr Yld 99 6 Handler Yld 99 5 Parts Hour 255 MCBI 201 Skt 1 Yld 99 9 Skt 2 Yld 100 Skt 3 Yld 100 Skt 4 Yld 100 Skt Cycles 249 End Select Job 1 Job 2 End of List Socket Socket 1 Enabled Socket 2 Enabled Socket 3 Enabled Socket 4 Enabled Adapter Statistics Reset Clean Count Clean Count Clean Alert 3500 No 22113204 Mfg 09 23 02 Actuations 1055 Adptr Life 10000 Insertions 4220 Pass 4202 Fail 16 Yld 99 5 Socket 1 Insertions 1055 Pass 1053 Fail 2 Yield 99 8 Socket 2 Same as 1 Socket 3 Same as 1 Socket 4 Same as 1 Supervisor Menus 10 ProLINE RoadRunner Operator s Guide A Refer to the previous page for the main menu Note that many of the values shown such as the Teach and Network menus are for example only Light gray shaded fields cannot be changed O
18. sor Menus 9 Warnings and Cautions 12 Technical Support 53 Chapter 1 Overview 2 ProLINE RoadRunner Operator s Guide A Data I O is proud to introduce a revolutionary new inline solution for high volume programming of electronic products ProLINE RoadRunner 1 Takes programmable devices from a reel 2 Places them in sockets and programs them with your data 3 Places them on a conveyor belt 4 Delivers them to the pick point of your assembly machine 2 3 4 1 The ProLINE RoadRunner for Fuji 3 ProLINE RoadRunner Operator s Guide A TaskLink for Windows is required to process devices on ProLINE RoadRunner TaskLink allows you to create and manage a job database and it analyzes job statistics PCMCIA cards are used to transfer jobs and statistics between TaskLink and RoadRunner For more information on TaskLink see the TaskLink Help Menu Programming Jobs Statistics Jobs and Statistics 4 ProLINE RoadRunner Operator s Guide A 1 SMT Communications Connection 2 Power and Air Connections 3 Power Switch 4 Handhold for lifting 5 PCMCIA Card Slot 6 Control Panel 7 Conveyor Belt 8 Mechanical Interface to the Multi Feeder Unit 9 Electronics Enclosure 10 Robotics Cover External View Front Back Cables not shown 4 3 2 7 1 6 8 9 10 5 5 ProLINE RoadRunner Operato
19. t no additional devices will get picked from the tape Ending a Job gt Job Advance Pocket Align Pocket 1 View Results gt End 2 37 ProLINE RoadRunner Operator s Guide A 3 Clear away excess devices from the conveyor belt 4 Empty the Reject Bin See next heading 5 Empty the Cover Tape Take Up Reel See Emptying Cover Tape ahead several pages 3 4 5 38 ProLINE RoadRunner Operator s Guide A To empty the Reject Bin 1 Press the Pause button 2 Pull the Reject Bin out by grabbing the finger tab and then lift up and out When reinserting the Reject Bin be sure the bin is completely lowered so that the tab is positioned out of the path of the probes Emptying the Reject Bin 2 Warning Pinch Warning Keep hands away from moving parts 39 ProLINE RoadRunner Operator s Guide A To empty the Cover Tape Take Up Reel 1 Press Pause 2 Cut the cover tape leaving enough slack to reattach 3 Pull the Take Up Reel straight out Reels with slots require rotating before pulling off 4 Unwind the used cover tape and discard it 5 Replace the Take Up Reel slide it on and rotate it to line up with the pins and push or twist Emptying Cover Tape Warning Pinch Warning Keep hands away from moving parts 3 4 5 5 40 ProLINE RoadRunner Operator s Guide A To shut down RoadRunner 1 Press Pause 2 Select End Jo
20. und 27 ProLINE RoadRunner Operator s Guide A 3 Without touching the gold contact surfaces on the bottom of the adapter lift the adapter free 4 Insert the correct adapter making sure that it seats on the dowel pins NOTE Each type of device may have its own Socket Adapter 5 Tighten the screws and replace the Actuator Plate 3 28 ProLINE RoadRunner Operator s Guide If you have an Adjustable Tape In Module you may need to adjust the tape width Adjustable Tape In Module only If the etched number on the 3 Position Spacer does not match your tape width dimension mm 1 With the power off 0 move the PNP Head out of the way 2 Loosen the Position Locking Screw several turns using a 4 mm Allen wrench Adjusting the Tape In Module Non Adjustable Adjustable 2 Current Setting 29 ProLINE RoadRunner Operator s Guide A 3 Rotate the 3 Position Spacer with your finger until you read 16 24 or 32 corresponding to your tape width 4 Retighten the Position Locking Screw 5 Rotate the Peel Bar counterclockwise 180 degrees to the up position 6 Lift and move the magnetic Front Track to the position that fits your tape width 7 Rotate the Peel Bar back down 3 4 5 6 6 30 ProLINE RoadRunner Operator s Guide To load and thread device tape 1 Place a reel onto the RoadRunner spindle 2 Lock the reel in place by rotating the brass button o
Download Pdf Manuals
Related Search