Fisher VCB-3574IR User's Manual
Contents
1. Lens mount cap The cap is installed to protect the lens mount section Remove the lens mount cap before installing a lens sold separately Flange back adjustment screw FLANGE BACK ADJ Flange back lock screw FLANGE BACK LOCK Camera installation bracket The bracket can be fixed at the top or bottom of the camera When fixing the bracket be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings Shorter screws M3 x 4 Longer screws M3 x 6 Camera mounting screw hole 1 4 20 UNC CAUTION When installing the camera support select a location that can support the total weight of the camera and accessories English 5 PARTS NAMES DC VIDEO A I LENS E Concerning auto iris lenses DC type auto iris lens A lens without amplifier circuit that operates only on a DC power source In general this type of lens is referred to as DC type coil lens or DC type non amplifier lens Set the A I LENS switch to the DC position VIDEO type auto iris lens A lens with amplifier circuit that operates on video signal and DC power source In general this type of lens is referred to as EE amplifier type lens ALC and LEVEL volume level controls are available on the lens for iris adjustments Set the A I LENS switch to the VIDEO position HE Compatible auto iris lenses 1 2 inch Sanyo DC type lens 1 2 or 2 3 inch VIDEO type len2. bright or dark cm lt mr L H e If the brightness of the picture on the monitor is not correct English 11 E Backlight compensation setting Use an autoiris lens and set the El BLC switch to the BLC ON position to engage the backlight compensation function Use an auto ins lens Set the EI BLC switch to BLC ON switch to the ON position El ON OFF ON BLC If using a VIDEO type auto iris lens e The ALC volume on the lens should be tumed all the way to Av Average e If the backlight compensation function does not compensate properly for the conditions set using the LEVEL volume on the lens CAUTION The electronic iris function and the backlight compensation function cannot operate simultaneously SETTINGS E Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor there may be a vertical roll of the images when switched In such a case set as described below Switch the display on the monitor from camera 1 to camera 2 Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops If more than two cameras are used please repeat this procedure for all the cameras de CAUTION If the vertical roll cannot be corrected by setting the LINE PHASE volume on camera 2 try setting the LINE PHASE volume on camera L If it still cannot be corrected please check that the polarity of the power cords of all
3. compensation Electronic iris function Electronic iris range Flange back Gamma correction Lens mount Environmental conditions Power supply English 13 HA standard 525 TV lines 30 frames sec PLL2 1 interlace 1 2 inch solid state image device CCD 811 H x508 V 768 H x 494 V Line lock Extemal sync Automatic switching 570 TV lines horizontally 350 TV lines vertically 1 0 Vp p 75 ohms composite More than 50 dB Approx 0 02 lux with a F 1 2 lens approx 0 03 lux with a F 1 4 lens Manual ON OFF switching zone light measuring system Active when using an auto iris lens Manual ON OFF switching 0 02 lux to 10 000 F 1 2 lens 0 03 lux to 15 000 F 1 4 lens 12 5 mm 0 8 mm y 0 45 CS mourt or C mount with the supplied adaptor Temperature 10 C 450 C Humidity less than 90 no condensation 24V AC 4 to 4 V 60 Hz 3 1 W with auto iris lens 2 4 W without auto iris lens Approx 330 g without lens Power consumption Weight HE Dimensions 11 1 4 20 UNC Features and specifications are subject to change without prior notice or obligations SERVICE This camera is a precision instruments and if treated with care will provide years of satisfactory performance However in the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Ser
4. the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail LABOR PARTS IMAGE DEVICE 3 YEARS 3 YEARS 3 YEARS EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts antenna knobs batteries or image burns to projection or picture tubes caused by electronic devices or games This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party
5. RTS NAMES sssssississsccossssavicisaisoiervevosserssssarienssntersansusiersstunscedantenverts 4 MOUNTING THE LENS scesssscsssssssscsssesssecssessseesseesseesseesseessseesseess 7 CONNECTIONS wsissssssescccsansesisrsccssssatsancnisersartaccesaasseuscnsstsosnarvavsusisrsanteyes 9 SETTING Sis sssisaiissiscsacsesiacisssasiet astcaiateetcedanteuesesnsasatedaudaugeesausdsiattavedapiess 10 TROUBLESHOOTING ssssssssecssessstecssecsstecssecsssecsseesssecsseessseesseesasessaes 12 SPECIFICATIONS niinno naaa A 13 ACCESSORIES C mourt adaptor 5 MM 1 pc The C mount adaptor must be used to be able to install a C mount lens on the camera Lens iris plug 4PIN ceseeeeeeeeeseeee 1 pc English 1 FEATURES e Infrared signals immediate area sensitivity is improved by about 10 dB from previous models e Builtin interline transfer method 1 2 CCD approx 410 000 picture elements e Low smear anti blooming low lag no buming and no geometric distortion using the CCD solid state image device e 100 solid state components giving excellent immunity to shock and vibration e Not subject to interference from magnetic or electrostatic fields e High sensitivity minimum required illumination of 0 02 lux with F1 2 lens e Horizontal resolution more than 570 TV lines e New backlight compensation function Active when using an autoris lens e Btternally adjustable flange back mechanical focus e Low power consumption and qui
6. SANYO INSTRUCTION MANUAL VCB 3574IR B W CCD Camera About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference SANYO INDUSTRIAL VIDEO B W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation SFC s warranty administrator at any of the addresses listed below or by calling toll free 1 800 421 5013 New Jersey Office California Office Illinois Office 210 Riser Road 1200 W Artesia Blvd 900 N Arlington Heights Rd Little Ferry NJ 07643 Compton CA 90220 Itasca IL 60143 201 641 3000 310 537 5830 708 775 1414 THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING HAWAII AND ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO FISHER USA CORPORATION warrants this SANYO product against defects in materials and workmanship for
7. ck start e 24V AC operation Commarcially available 24 V AC adaptor INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT WARNING TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 Pour la client le canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB003 du Canada This installation should be made by a qualified service person and should conformto all local codes This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harrful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause hanvful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by tuming the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorien
8. connected devices is correct TROUBLESHOOTING Before taking the camera for repairs please check below to make sure that the camera is used correctly If it still does not perform correctly please consult your dealer or a Sanyo Authorized Service Centre E No picture on the monitor screen e Isthe power tumed on to all connected devices Is the voltage correct e Areall the signal connecting cables correctly connected e Isthe lighting sufficient e Has the lens cap been removed e Isthe lens type DC or VIDEO correctly selected Depending on the type of lens the A I LENS switch must be set accordingly e Isthe iris control correctly set A When using a DC type lens the LEVEL volume inside the camera casing should be adjusted B When using a VIDEO type lens the LEVEL volume on the lens should be adjusted E The picture is not clear e Isthe monitor correctly adjusted e Isthe flangeback position correctly set e Isthe lens focus correctly adjusted e Are the lens surfaces clean If there is dust or finger prints on the lens the image quality will deteriorate To clean the lens use a soft cloth or a commercially available lens deaning set 12 English SPECIFICATIONS Scanning system Interlace Image device Picture elements Effective picture elements Synchronizing system Resolution Video output level Video S N ratio Minimum required illumination incandescent lighting Backlight
9. he FLANGE BACK LOCK screw CONNECTIONS Q A YG Al I lt 4 i 4 Video signal connections gt gt gt VIDEO IN gt gt VIDEO OUT English 9 Basic connection for monitoring or recording The peripheral devices VCR monitor lens etc and cables are sold separately 1 Make the video signal connection between the camera and the monitor or time lapse VCR 2 Connect to 24 V AC UL listed class 2 power supply CAUTION To prevent camera and or power supply failure pay close attention to polarity when making the connections e To prevent fire hazard any UL listed wire rated VW 1 should be used for the 24 V AC cable input terminal 3 Insert the plug of this power cord into a wall outlet The POWER indicator A will light Adjust the picture on the monitor using the Brightness and Contrast controls WE Coaxial cable type and maximum length e Cable type RG 59U 3C 2V 250 m maximum e Cable type RG 6U 5C 2V 500 m maximum e Cable type RG 11U 7C 2V 600 m maximum CAUTION e The RG 59U type cable should not be run through electrical conduits or through the air e Using CCTV Video grade coaxial cable SETTINGS War z a LH DC VIDEO A l LENS Control name Position Electronic iris El Backlight compensation BLC switch OFF Auto iris lens switch A I LENS DC Lens ir
10. horized Service Centre Be careful to protect the camera from rain sea water etc W Be careful when handling the unit To prevent damages do not drop the camera or subject it to strong shock or vibration E Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image English 3 E Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust E Protect from high temperatures Do not install close to stoves or other heat generating devices such as spotlights etc or where it could be subject to direct sunlight as that could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels Install where the temperature range will stay between 10 C and 50 C no condensation E Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure t
11. is level volume LEVEL about centre E Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop Set the EI BLC El switch to EI ON position on Note on Please refer to the specifications for dynamic BLC range of the electronic iris CAUTION e The dectronic iris is suitable for normal indoor use When the EI BLC switch is set to the EI ON postion do not use an autonris lens e If used under fluorescent light the image may flicker In such a case change to incandescent lighting or set the EI BLC switch to the OFF position and use an auto iris lens e When shooting bright subjects pay attention to the light angle in order to avoid or minimize the smear phenomenon effect When using an auto iris lens for indoor outdoor use Set the El BLC switch to the OFF position CAUTION If conditions are outside the electronic iris operation range or more than the maximum illumination it will cause saturation of the CCD In that case use a manual iris lens 10 Engish SETTINGS E Lens iris adjustment If using a DC type auto ris lens you will need to set the LEVEL VR401 volume when shooting in the conditions described below L counterclockwise To decrease the contrast H clockwise To increase the contrast e If shooting simultaneously in a dark room and through a bright window VR401 e If the subject background is extremely
12. o read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling PARTS NAMES Video output connector VIDEO OUT BNC type Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector Line phase adjustment volume LINE PHASE When using two cameras or more the image on the monitor may roll vertically when switching sources This rolling can be minimized by tuming this volume External sync composite video signal input connector VS IN BNC type Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor Power indicator POWER Comes on when the power to the camera is on 24 V AC input terminal 24 V AC GND Connect to 24 V AC UL listed class 2 power supply Camera setup section under the cover These settings are for when using a 1 3 inch CS mount DC without EE intemal amplifier type lens However if due to installation conditions or environment the settings may need to be modified for best results see SETTINGS To access the controls loosen the cover fixing screw then remove the cover Lens iris output connector LENS This 4 pin connector is used to send the DC control signal and power supply to an auto ris type lens 4 English PARTS NAMES
13. original plug and using a soldering iron connect the supplied lens iris plug according to the diagram Refer to page 8 MOUNTING THE LENS E Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable Cut the cable at the plug then remove approx 8 nm of the cable sheath and strip about 2 mm from each wire 2 Install the lens iris plug Solder the cable to the pins following the correct pin layout refer to the table and illustrations then close the plug cover Pin layout DC type lenses VIDEO type lenses Brake coil 2 V DC 50 mA max Brake coil Not used Drive coil 4 Video output 1 0 Vp p high impedance Drive coil Ground for video signal and DC power E Flange back adjustment If the pick up surface is not correctly positioned with relation to the lens focal point the picture will be out of focus in particular when using auto iris power zoom lenses sold separately If that is the case adjust the flange back position as described below 1 Using a screwdriver loosen the FLANGE BACK LOCK screw M2 Set the zoom lens to the maximum telephoto position set the focus using the focus ring on the lens 2 Set the zoom lens to the maximum wide angle position set the focus using the FLANGE BACK ADJ screw 3 Repeat steps 2 and 3 until the image stays in focus when changing froma telephoto shot to a wide angle shot When the setting is complete tighten t
14. s VCL CS12GY Standard angle f 12 mm Standard angle f 9 mm VCL CS6GY Wide angle f 6 mm Telephoto angle f 12 mm VCL CS3GY Ultra wide angle f 3 7 mm More telephoto angle f 16 mm W If using a VIDEO type auto iris lens e Set the ALC and LEVEL controls on the lens to adjust the iris Normally the ALC volume should be tumed all the way to Av Average e Depending on the type of lens used the lens may not perform properly In such a case adjust the LEVEL volume on the lens casing to correct 6 English MOUNTING THE LENS C mount type lens 2 CS mount type lens English 7 Please use a DC type auto iris lens sold separately Checking the lens mount Do not use a lens if length L is more than 7 mm If not that may damage the camera and prevent proper installation Remove the lens mount cap from the camera Install the auto iris lens CS mount type lens Carefully align the lens mount with the camera opening then tum the lens slowly to install it C mount type lens To allow for flange back adjustment install the supplied C mount adaptor on the lens mount then carefully align the lens mount with the camera opening and tum the lens slowly to install it Connect the lens plug to the lens iris output connector LENS on the side of the camera When using lenses from other makers the plug shape may not correspond to the terminal on the camera In such a case remove the
15. t or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for hap This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harnful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Sanyo may void the user s authority to operate this camera 2 English PRECAUTIONS HB Incase of problem Do not use the camera if smoke or a strange odour comes from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Centre E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera If used with a foreign object inside it could cause a fire short circuits or damages If water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Aut
16. to assume for it any other obligation or liability THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IS LIMITED TO THE TERM OF THIS WARRANTY IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE ATTENTION For your protection in the event of theft or loss of this product please fill in the information below for you own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased 14 Engish Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer CONTENTS INFORMATION TO USER ssssssscsssesssscsssessseesseessseesseessseesseesseesseesasees 2 PREGAUTIONS sscscsisscsasccsicesnsscecsinccbcsatacesdivtsancaacdaiassaniecsanteanasndaniatsanecns 3 PA
17. vicing should always be referred to your dealer or Sanyo Authorized Service Centre
Download Pdf Manuals
Related Search