Fisher-Price G5175 Instruction Sheet
Contents
1. 1 6 aoe 8 x 13 8 Screw 4 q Shown Actual Size e Turn the seat face down Fit an accessory bin into the groove on each side of the seat as shown e Insert two 8 x 12 s screws into each accessory bin and tighten Assembly e Position the seat assembly so that the front of the seat is toward the curved front base e While pressing the buttons on the swing tubes insert them into the frame hubs Push the swing tubes up until the but Fit the pocket on the back of the pad onto the seat back tons snap into the hole in the frame hubs Fit the waist belts through the smaller slots in the pad e Push down on the seat to be sure the seat is secured in both frame hubs Frame Hubs 8 x 13 8 Screw 2 Shown Actual Size e Lift the bottom of the pad Insert a 8 x 13 8 screw into each frame hub and tighten Insert the pad elastic loops through the holes in the Again push down on the seat to be sure the seat is secured seat bottom to both frame hubs e Insert the crotch belt through the slot in the pad e From under the seat fit the elastic loops onto the tabs on the seat bottom Assembly Battery Installation Hint When swinging sound or power L E D slows dims stops it s time to replace the batteries We recommend using alkaline batteries for longer battery life Elastic Loop Battery _ Compartment Door Installation 21 e Locate t2. tings In most cases the low setting works best for a smaller child while the high setting works best for a larger child B Parent Activated Product features and decorations may vary from picture below Accessories sold separately FON ots a _ Mode me 9 o Music Volume nD Swing Mode Switch Music Volume Switch e Slide the switch to 6 parent activated The power L E D e Select for music highest volume lights and the swing begins swinging Select for music high volume Be sure to turn the product off O when not in use e Select for music low volume Speed Dial Select Oto turn music off e Select any of five speed settings Hint As with most battery powered swings a heavier child will reduce the amount of swinging motion on all set tings In most cases the low setting works best for a smaller child while the high setting works best for a larger child 14 Storage Care The pad is machine washable Wash the pad separately in cold water on the gentle cycle Do not use bleach Tumble dry separately on low heat and remove promptly The frame tray and toybar may be wiped clean using a mild cleaning solution and a damp cloth __ gt Elastic wee Loops Lower Pad Pocket i Restraint Belts e Turn the toy bar back to it s storage position e Press the button on the inside of each housing and push the rear legs toward the front legs Stand the frame against a
3. wall for storage To remove the pad e Unhook the four elastic hooks from the pegs on the seat back and bottom Push the restraint belts back through the slots in the pad e Slide the upper pad pocket off of the seat back e Slide the lower pad pocket off of the seat bottom To replace the pad e Refer to Assembly steps 19 21 Note This product has no consumer serviceable parts Do not take this product apart 15 One 1 Year Limited Warranty Fisher Price Inc 636 Girard Avenue East Aurora New York 14052 warrants that Smart Response Swing is free from all defects in material and workmanship when used under normal conditions for a period of one 1 year from the date of purchase Should the product fail to perform properly we will repair or replace it at our option free of charge Purchaser is responsi ble for shipping the product to Consumer Relations at the address indicated above and for all associated freight and insurance cost Fisher Price Inc will bear the cost of shipping the repaired or replaced item to you This warranty is void if the owner repairs or modifies the product This warranty excludes any liability other than that expressly stated above including but not limited to any incidental or consequential damages SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC L
4. bar plugs into the sockets on the swing tubes Hint If the toy bar plugs do not fit into the sockets turn the toy bar around Now fit the plugs into the sockets e Insert two 6 x s screws into each plug and tighten Securing Your Child IMPORTANT Before each use inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts A WARNING e To prevent serious injury or death from falls and being strangled in the restraint system Always use the restraint sys tem Never rely on the tray to restrain child Never use with an active child who may be able to climb out of the seat e Never leave child unattended e Place your child in the seat Position the crotch belt between your child s legs e Fasten both waist belts to each side of the crotch belt Make sure you hear a click on both sides e Check to be sure the restraint system is securely attached by pulling it away from your child The restraint system should remain attached 10 2 _ Tighten Loosen To tighten the restraint Feed the anchored end of the waist belt up through the buckle to form a loopQ Pull the free end of the waist belt To loosen the restraint Feed the free end of the waist belt up through the buckle to form a loop Q Enlarge the loop by
5. could void the user s authority to operate the equipment For other countries outside the United States Canada call 1 800 567 7724 or write to Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario L5R 3W2 Great Britain telephone 01628 500302 Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 New Zealand 16 18 William Pickering Drive Albany 1331 Auckland Asia Mattel East Asia Ltd Room 1106 South Tower World Finance Centre Harbour City Tsimshatsui HK China Printed in China B2108c 0920
6. into a hexagonal opening in the bracket Make sure the rounded side of the lock nut is facing up Fit the grooves on the bracket to the seat tubes as shown e Rotate the seat tubes down __ Seat Wire racket Slot B Y M4 Screw 4 Shown Actual Size e Fit the seat wire through the slot in the bracket as shown Insert four M4 screws into the seat tubes and tighten Press in Place Seat Wire is Through Hole in Seat Wire Cap Seat Wire Caps Lift the seat tubes slightly Press the seat wire caps e With the seat wire hanging down insert the ends of the seat into place wire through the slots in the seat as shown Shown Actual Size J through each seat wire cap LS p Rounded Edge Up and tighten 6 x Screw 4 Insert two 6 x screws Hint The seat wire caps are designed to fit into the seat only one way If the screw holes in the seat wire caps do not align with the holes in the seat try switching the seat wire caps onto the opposite ends of the seat wire Seat Wire Cap Hole o J 1 4 Seat Wire Cap Eee E Ends of Seat Wire Seat Wire Cap Accessory Bin Accessory Bin e While holding the seat wire in place carefully turn the seat around so that the front faces you e Position the seat wire cap so that the rounded edge is upright Fit each end of the seat wire through the hole in each seat wire cap
7. EGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE Fisher Price Inc a subsidiary of Mattel Inc East Aurora NY 14052 U S A 2003 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc FCC Statement United States Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interfer ence will not occur in a particular installation If this equip ment does cause harmful interference to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note Changes or modifications not expressly approved by the manufacturer responsible for compliance
8. Fisher Price Smart Response Swing Product features and decorations may vary from picture above Accessories sold separately Model Number B2108 B3469 G5175 PLEASE KEEP FOR FUTURE REFERENCE Please read these instructions before assembly and use of this product as they contain important information Adult assembly is required Tool needed for assembly Phillips Screwdriver not included Requires four D LR20 alkaline batteries for operation Maximum Weight Limit 24 Ibs 10 9 kg IMPORTANT The maximum weight limit for this product is 24 lbs If your child weighs less than 24 Ibs but is really active and appears to be able to climb out of the swing immediately discontinue its use Warnings and Caution A WARNING e To prevent serious injury or death from falls and being strangled in the restraint system Always use the restraint sys tem Never rely on the tray to restrain child Never use with an active child who may be able to climb out of the seat e Never leave child unattended A CAUTION This product contains small parts in its unassembled state Adult assembly is required Consumer Information Occasionally a consumer may experience a problem with one of our products If this should happen please call us toll free rather than return this product to the store Usually we can solve the problem over the telephone or send you replacement parts Please call Fis
9. at this procedure to assemble the other front leg to the front base e While standing on the front base pull the front legs up The front legs should remain secured to the front base If you can remove the front legs you have not assembled them correctly to the front base Reread and repeat assembly step 1 Housing Slot 2 N Motor Y Housing Position the housing so that the hub is inward e While pressing the button on the top of front leg insert it into the housing slot as shown Push the front leg until the button snaps into the hole in the housing e Repeat this procedure to assemble the motor housing to the other front leg Pull the front legs down to be sure they are secure in the housings If you can remove them you have not assembled them correctly Please re read and repeat this assembly step Motor Housing Short Tube woe Tapered End e Position a rear leg so that the tapered end is upright e While pressing the button on the top of the rear leg insert it into the housing short tube as shown Push the rear leg until the button snaps into the hole in the short tube e Repeat this procedure to assemble the other rear leg to the motor housing short tube Pull the rear legs down to be sure they are secure in the housings If you can remove them you have not assembled them correctly Please re read and repeat this assembly step Assembly Rear Base e While stand
10. he battery compartment door on the swing frame e Insert a coin into the battery compartment door and pry the battery compartment door off of the swing frame Insert four D LR20 alkaline batteries Fit the bottom edge of the pad around the bottom edge Replace the battery compartment door of the seat Hook the elastic loops on each side of the pad to the peg on the back of the accessory bins unang 6 x 5 3 Screw 4 _ Shown Actual Size A N E Toy Bar ee SA Toys may be different 1 5Vx4 D LR20 SHOWN ACTUAL SIZE Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your product To avoid battery leakage Do not mix old and new batteries or batteries of different types alkaline standard carbon zinc or rechargeable nickel cadmium e Insert batteries as indicated inside the battery compartment e Remove batteries during long periods of non use Always remove exhausted batteries from the product Dispose of batteries safely Do not dispose of batteries in a fire The batteries may explode or leak e Never short circuit the battery terminals e Use only batteries of the same or equivalent type as recommended Do not charge non rechargeable batteries Remove rechargeable batteries from the product before charging If removable rechargeable batteries are used they are only to be charged under adult supervision Fit the toy
11. her Price Consumer Relations toll free at 1 800 432 5437 8 AM 6 PM EST Monday through Friday Hearing impaired consumers using TTY TDD equipment please call 1 800 382 7470 Or write to Fisher Price Consumer Relations 636 Girard Avenue East Aurora New York 14052 Parts SO 2 Accessory Bins Housing 2 Rear Legs 2 Front Legs Shorter Longer Motor Housing Y Toy Bar Front Base x Rear Base Bracket with M4 Lock Nuts Seat with Restraint 4 e 2 Seat Wire Caps Seat Wire a0 G Caa M4 Screw 4 8 x 1 Screw 6 6 x Screw 8 Shown Actual Size Shown Actual Size Shown Actual Size Note Tighten or loosen all screws with a Phillips screwdriver Do not over tighten the screws Assembly IMPORTANT Before assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts Front Legs Longer Tapered End Press Button Press pa Button N S XN Tapered End Front Base Place the front base on a flat surface e Position a front leg longer so that the tapered end is downward as shown e While pressing the button on one of the front legs insert it into the front base Push down on the front leg until the button snaps into the hole in the front base e Repe
12. ing on the rear base pull the rear legs up They should remain secured to the rear base If you can remove the rear legs you have not assembled them cor rectly to the rear base Reread and repeat assembly step 6 Set the frame assembly aside for Assembly step 17 Seat Tube t Long Ends ae ee A Ridges e Place the rear base on a flat surface so that the buttons face the front base e While pressing the buttons on each side of the rear base fit the rear legs onto the rear base Push the rear legs down until the buttons on the rear base snap into the holes in each rear leg cA Top of Seat e Position the seat face down with the top of the seat facing you e Position a seat tube so that the long end is upright and toward you and the curved end is toward the outside edge of the seat e Insert the curved end of the seat tube through the holes in the ridges on the seat back e Repeat this procedure to assemble the other seat tube to 5 the seat Assembly M4 Lock Nut Rounded Side N Shown Actual Size J Grooves ta Lock Nut Hexagonal Opening Position the bracket so that the tall end is toward the bottom edge of the seat Hint The M4 lock nuts have been assembled to the bracket at the factory During shipment of this product they may have fallen out Check to be sure there is a lock nut in each hexagonal opening on the bracket If one or more has fallen out fit the lock nut
13. pulling on the end of the loop toward the buckle Pull the anchored end of the waist belt to shorten the free end of the waist belt Note After adjusting the restraint to fit your child make sure you pull on it to be sure it is securely fastened Adjusting the Seat Using the Toy Bar Toy Bar Adjust the seat angle in any of three positions Upright Semi Recline or Recline To adjust the seat angle Push down on the seat back to position the seat wire in the desired groove in the bracket for Upright Semi Recline or Recline Lift or lower the toy bar for baby s enjoyment Using the Tray Fit the tray onto the seat armrests Swing Modes The Smart Response Swing has two modes Baby Sounds Activated amp and Parent Activated 6 Product features and decorations may vary from pictures below Accessories sold separately ia j n ET ae Parent Activated Q F aby Sounds Activated IMPORTANT The maximum weight limit for this product is 24 Ibs If your child weighs less than 24 Ibs but is really active and appears to be able to climb out of the swing immediately discontinue its use 12 Baby Sounds Activated Product features and decorations may vary from picture below Accessories sold separately ih j wY nm e e Speed via S N _ Sound Sensitivity Dial 9 4 t Music Volume Switch ag T Power L E D e I Swing Mode
14. switch_ Jf oO Sound Sensitivity Dial Swing Mode Switch Slide the switch to high sensitivity for incoming e Slide the switch to baby sounds activated The sounds listens for shallow sounds power L E D lights The swing begins swinging for about Slide the switch to low sensitivity for incoming sounds 15 20 minutes and if you have selected music five songs listens only for loud sounds play about 15 20 minutes After swinging and music stop the swing is ready to listen for your baby s sounds for about Hint You may want to start with the high sensitivity setting two hours at first When baby cries the swing and music if selected auto matically turns on to soothe baby Music Volume Switch If the swing is not activated from baby s sounds within two e Select for music highest volume hours of selection the power L E D flashes to tell you that it e Select for music high volume going to turn off Once it has turned off and the power Select 4 for music low volume L E D is not lit you will need to slide the switch to the off Select to turn music off position and back to baby sounds activated The Speed Dial swing is now re set to listen for your baby s sounds for another two hours e Select any of five speed settings Be sure to turn the product off when not in use Hint As with most battery powered swings a heavier child will reduce the amount of swinging motion on all set
Download Pdf Manuals
Related Search