Fisher-Price W2602 User's Manual
Contents
1. Undercharged battery Battery needs charging Battery is old and will not accept full charge Vehicle is overloaded Driving conditions are too stressful Loose wire or connector Motor or electrical switch damage SOLUTION It is possible that only one rear wheel may spin when both rear wheels are raised off the ground and the vehicle is in low speed This does not necessarily indicate a problem Check for proper operation of the drive system by raising the rear wheels off the ground and pressing the foot pedal If only one rear wheel spins carefully press your hand on the spinning wheel to slow it down The other rear wheel should begin to spin If the other rear wheel does not begin to spin there may be a problem with the vehicle Contact your local Power Wheels authorized service center for diagnosis and repair Charge the battery A new battery should have been charged for at least 18 hours before using the vehicle for the first time After first time use recharge the battery for at least 14 hours after each use Never charge the battery longer than 30 hours Check all connectors Make sure the battery connector is tightly plugged into the charger connector and that the charger is plugged into the wall Make sure power flow to the wall outlet is ON Be sure to charge the battery after each use Even with proper care a rechargeable battery does not last forever Average battery life is 1 to 3 years depending o2. N WARNING Prevent Injuries and Deaths Direct Adult Supervision Required e Never Ride at Night Keep Children Within Safe Riding Areas These areas must be Away from swimming pools and other bodies of water to prevent drownings Generally level to prevent tipovers Away from steps steep inclines cars roads and alleys Hiding Rules Make sure children know and follow these rules for safe driving and riding Always sit on the seat Always wear shoes Only 2 two riders at a time Use vehicle on generally level ground ONLY W2602pr 0920 20 he vehicle to gain unsafe speed even if the pedal is released to stop he vehicle to tilt and tip over he wheels to lose traction causing the vehicle to slip he vehicle could roll backwards at an unsafe speed e Never put anything near any moving parts Rotating parts such as motors gear boxes and wheels can snag fingers hair etc causing serious injury e Do not allow operation of the vehicle when it is on its side or in an upside down position Do not operate the vehicle near flammable vapors gasoline paint thinner acetone liquid wax etc The vehicle s electrical switches like most electrical switches emit an internal spark when first turned on or turned off which could cause an explosion or fire e To prevent unsupervised use of the vehicle disconnect the motor harness from the battery when the vehicle is not in
3. are available to take your call in English or French Habla Espanol Si usted tiene alguna pregunta necesita asistencia llame gratis 1 800 348 0755 para los Estados Unidos Tenemos representantes que hablan espanol para atender su llamada For your convenience Power Wheels maintains an independently owned and operated Authorized Service Center Network with more than 300 authorized service centers nationwide Our authorized service centers will repair or replace parts under warranty at no extra charge and can perform non warranty repairs for a minimal charge To find the authorized service center nearest you please visit us online at www powerwheels com or call 1 800 348 0751 Please visit us online at www powerwheels com to register your vehicle W2602pr 0920 ASSEMBLED PARTS e f you experience a problem with this product please call us at 1 800 348 0751 rather than return this product to a store e Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded e Metal parts have been coated with a lubricant to protect them during shipment Wipe all metal parts with a paper towel to remove any excess lubricant 2 Valve Covers SH 2 Front Wheels 2 Rear Wheels Steering Post Steering Column 2 Rims Left and Right Left and Right Rear Axle 2 Front Fenders 2 Rear Fenders Left and Right Left and Right Steering Wheel Hood 2 Sid
4. into place e Repeat steps 9 14 to assemble the remaining bushing e Fit a s 1 cm lock nut onto the end of the front axle front wheel rim and front hubcap to the other front axle and tighten with the assembly wrench IMPORTANT Fully tighten the lock nut with the included assembly wrench male SONIS e Test to be sure the wheel spins Lift the front end of the vehicle up slightly and turn the wheel It should spin freely e f the wheel does not spin freely use the assembly wrench to loosen the lock nut a 1 4 turn Spin the e Fit each valve cover onto the back end of the vehicle wheel again and loosen more if necessary frame as shown Hint Each valve cover is designed to fit one way If the valve cover does not seem to fit try the other valve cover FRONT VIEW W2602pr 0920 10 ASSEMBLY 16 Comm e Insert three 8 x 34 1 9 cm screws into each valve cover and tighten Short Seat Belts Note Make sure the fasteners on both short seat belts face each other e Fit the folded end of each short seat belt down through the outer slots in the seat Do not insert the folded tab into the slot Pull up on each seat belt to make sure it is secure Folded Tab Fastener Side Side Fastener 18 Long Seat Belt Note Make sure the fasteners on the long seat belt are facing the fasteners on the short seat belts e Insert the ends of the long seat belt up through the slots in the center
5. of the seat e Fit the folded tabs on the belt up through the slots in the center of the seat to keep the long seat belt in place Make sure the folded tabs are on visible on the top side of the seat k Rear Fenders e Fit the rear fenders under the tabs the sides of the seat as shown W2602pr 0920 ASSEMBLY Seat Vehicle Frame 20 DO NOT insert screws here Comm e Insert two 8 x 3 4 1 9 cm screws into the upper hole in each side of the seat and tighten Note Do not insert screws into the lower holes on the seat in this step These screws will be assembled in this location in step 24 e Fit the seat onto the vehicle frame 21 e Insert a 8 x 12 1 3 cm screw into a hole in the front of the seat back ACIS e Insert six 8 x 1 9 cm screws into the seat and tighten e From behind the seat back fit a 78 32 acorn nut onto the end of the screw e While holding the acorn nut in place with the assembly wrench tighten the screw with a Phillips screwdriver Repeat assembly steps 21 and 22 to assemble the remaining 78 x 12 screw and 78 32 acorn nut to the seat back W2602pr 0920 12 ASSEMBLY Sidebar with Sidebar with Front Fenders Curve Out Curve Out Tabs V eX e Fit the sidebars into the slots in the vehicle frame and e Fit the front fenders onto the front of the vehicle rear fenders as shown Hint Each sidebar is designed to fit on
6. 2pr 0920 Rear Axle Cap e Fit a rear axle cap onto the end of the rear axle toon e Insert a 8 x 1 9 cm screw into the hole in the rear axle and tighten Rear Hubcap e Fit the tabs on the rear hubcap into the slots in the rear wheel Push to snap into place e Repeat steps 2 5 to assemble the other rear wheel rear axle cap and rear hubcap to the rear axle ASSEMBLY Front Axle C3 Front Axle e Pull to rotate the front axles completely towards the front of the vehicle Front Axle Fastener Cap Front Axle e Fit a front axle fastener cap onto the upper portion of a front axle e Align the hole in the axle fastener cap with the hole in the front axle Hint You may need to push the front axle towards the front of the vehicle while you insert the screw e Insert a 8 x 3 4 1 9 cm screw into the large opening in the front axle fastener cap and tighten e Repeat steps and 8 to assemble the other front axle fastener cap e Remove the cap on the end of the front axle Dispose of the cap in the trash e Slide a bushing ring end first onto a front axle I Front Wheel e Slide a front wheel flat side first onto the front axle e Slide a rim indented side out onto the front axle W2602pr 0920 ASSEMBLY m Front Hubcap Lock Nut Assembly e Fit the tabs on the front hubcap into the slots in the Wrench front wheel Push to snap
7. Owners Manual with Assembly Instructions For W2602 POWER WHEELS Please read this manual and savejitiwith your Original salesjreceipt Tools needed for assembly assembly wrench included Phillips Screwdriver and Adjustable Wrench both not included Use only witha Power Wheels amp 12 Volt Lead Acid Rechargeable Battery and a Power Wheels 12 Volt Charger both included IMPORTANT INFORMATION ELECTRICAL HAZARD DANGER To prevent electric shock do not immerse in water wipe clean with a damp cloth N WARNING Battery can fall out and injure a child if vehicle tips over Always use battery retainer PREVENT FIRE Never modify the electrical system Alterations could cause a fire resulting in serious injury and could also ruin the electrical system Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury Use of Power Wheels components in products other than Power Wheels vehicles could cause overheating fire or explosion e The battery must be handled by adults only The battery is heavy and contains sulfuric acid electrolyte Dropping the battery could result in serious injury Never allow children to charge the battery Battery charging must be done by adults only A child could be injured by the electricity involved in charging the battery e Read the safety instructions on the battery e Examine the battery charger and their connectors for excess
8. POSSIBLE PROBLEM CAUSE Vehicle does not run Undercharged battery Charger is not working Tripped thermal fuse Loose wires or loose connectors Dead battery Electrical switch damage Motor damage W2602pr 0920 SOLUTION Charge the battery A new battery should have been charged for at least 18 hours before using the vehicle for the first time After first time use recharge the battery for at least 14 hours after each use Never charge the battery longer than 30 hours Check all connectors Make sure the battery connector is tightly plugged into the charger connector and that the charger is plugged into the wall Make sure power flow to the wall outlet is ON There is no sure way to tell if your charger is working unless you have a volt meter If you suspect there is a problem with your charger contact your local Power Wheels authorized service center They can test your charger for you The built in thermal fuse may trip and shut down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe Once a fuse has tripped remove your foot from the pedal and wait 25 seconds before operating the vehicle again To avoid repeated automatic shutdowns do not overload the vehicle by exceeding the 130 Ibs 59 kg maximum weight capacity or by towing anything behind the vehicle Do not drive up hills or run into fixed objects which can cause the wheels to stop spinning while pow
9. a rechargeable battery does not last forever Average battery life is 1 to 3 years depending on vehicle use and use conditions Replace only with a Power Wheels 12 Volt battery with built in thermal fuse Do not substitute parts The built in thermal fuse may trip and shut down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe Once a fuse has tripped remove your foot from the pedal and wait 25 seconds before opperating the vehicle again To avoid repeated automatic shutdowns do not overload the vehicle by exceeding the 130 Ibs 59 kg maximum weight capacity or by towing anything behind the vehicle Do not drive up hills or run into fixed objects which can cause the wheels to stop spinning while power is still being supplied to the motors If a thermal fuse continually trips contact your local Power Wheels authorized service center The vehicle was pre set to run only in low speed To allow the vehicle to run in low and high speed you must disconnect the High Speed Lock Out Follow the instructions in the Vehicle Operation section to remove the High Speed Lock Out screw 25 W2602pr 0920 PROBLEMS AND SOLUTIONS GUIDE PROBLEM When the foot pedal is pressed only one rear wheel spins Vehicle runs sluggishly Vehicle runs sluggishly continued Sometimes the vehicle doesn t run but other times it does W2602pr 0920 POSSIBLE CAUSE Operation of vehicle in low speed
10. battery case for cracks and other damage which may cause sulfuric acid electrolyte to leak during the charging process If damage is detected do not charge the battery or use it in your vehicle Battery acid is very corrosive and can cause severe damage to surfaces it contacts e Do not place the battery on a surface such as kitchen counter tops which could be damaged by the acid contained inside the battery Take precautions to protect the surface on which you place your battery e Charge the battery in a well ventilated area e Once the battery is charged disconnect the battery connector from the charger connector Unplug the charger from the wall outlet Refer to the Battery Installation section for instructions on installing your battery If your battery is already installed in your vehicle simply re connect the motor harness connector to the battery e You do not need to remove the battery from your vehicle to recharge it W2602pr 0920 Assembly N WARNING Children can be harmed by small parts sharp edges and sharp points in the vehicle s unassembled state or by electrical items Care should be taken in unpacking and assembly of the vehicle Children should not handle parts including the battery or help in assembly of the vehicle Rear Axle e Slide the rear axle through the hole in the motor in the back end of the vehicle Rear Wheel e Slide a rear wheel onto the end of the rear axle W260
11. e way Make sure Hint The front fenders are designed to fit one way If the sidebar curves outward and the tabs on the ends fit a front fender does not seem to fit try the other one into the slots in the vehicle and fenders Sidebar Cover Sidebar Cover y NUNN e Fit the sidebar covers onto the sidebars as shown Hint The sidebar covers are designed to fit one way If a sidebar cover does not seem to fit try the other one e Insert a 8 x 1 9 cm screw into each sidebar cover and tighten C3 ca Comm e Insert six 8 x 1 9 cm screws into the fenders and tighten 13 W2602pr 0920 ASSEMBLY e Fit the folded end of the strap attached to the hood up into the slot in the front end of the vehicle e Fit the bumper onto the front end of the vehicle e Insert four 8 x 1 9 cm screws into the bumper and tighten Steering Post Hood 32 Steering Column e Insert the straight end of the steering column up through the bottom of the steering post as shown e Fit the tabs on the hood onto the pegs on the front fenders W2602pr 0920 14 ASSEMBLY Steering Lock Nut Steering Column Column Post Bend in Steering Column Assembly Wrench e Pull the straight end of the steering column up so that only the bend is visible out from the bottom of the Steering column post e Hold the steering column in place and lower the e Carefully turn the vehicle on its side assembl
12. ebars 2 Short Seat Belts Long Seat Belt Left and Right W2602pr 0920 4 ASSEMBLED PARTS f o e 2 Sidebar Covers Steering Wheel Cap 2 Front Hubcaps 2 Rear Hubcaps Left and Right am Re m P 2 Bushings 2 Front Axle Fastener 2 Rear Axle Caps Assembly Wrench Caps 12V Battery 12V Charger Part Not Shown Label Sheet Cy umm TT CN 88 x 1 9 cm Screw 34 8 x 1 3 cm Screw 2 3 1 cm Lock Nut 4 48 32 Acorn Nut 2 Fasteners Shown Actual Size For your convenience we included extra fasteners Note Tighten and loosen all screws with a Phillips screwdriver Do not over tighten the screws W2602pr 0920 ASSEMBLED PARTS Note Some parts shown are assembled on both sides of the vehicle Fasteners not shown W2602pr 0920 6 BATTERY CHARGING ELECTRICAL HAZARD WARNING e Battery can fall out and injure a child if vehicle tips over Always use battery retainer e PREVENT FIRE Never modify the electrical system Alterations could cause a fire resulting in serious injury and could also ruin the electrical system Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury Use of Power Wheels components in products other than Power Wheels vehicles could cause overheating fire or explosion e The battery must be handled by adults only The battery is heavy and contains sulfuric acid electrolyte Dropping the battery could re
13. el rub the label firmly with a clean dry cloth to make sure the label is adhered to your vehicle Start at the center of a label and smooth towards the outer edges to remove air bubbles 4 HS N HJIJV H INNU TOP VIEW 24 23 BACK VIEW 17 W2602pr 0920 DECORATION RIGHT SIDE VIEW LEFT SIDE VIEW W2602pr 0920 18 BATTERY INSTALLATION IMPORTANT Use only a Power Wheels 12 volt battery Use of any other battery will damage your vehicle Battery Door Press the battery door button on the back end of the vehicle Lower the battery door Power Wheels 12 Volt Battery e Carefully fit the battery into the battery compartment 19 Motor Harness A N e Plug the motor harness connector into the battery Push firmly Battery Door e Lift the battery door and snap into place W2602pr 0920 SAFE DRIVING RULES Before children use this vehicle an adult should carefully evaluate the driving area as well as the child s skill level and ability to drive the vehicle safely Teach appropriate Safety rules to your child before allowing operation of this vehicle These rules should also be reviewed with other playmates who want to drive the vehicle e A child who is not sitting on the seat could fall off cause a tip over or block the driver s view e Only operate the vehicle in the daytime in a well lit area e Driving near steep inclines can cause RIDING HAZARD
14. er is still being supplied to the motors If a thermal fuse continually trips contact your local Power Wheels authorized service center Check all wires and connectors Make sure the battery connector is tightly plugged into the motor harness connector and that there are no loose wires around the motors If your battery is old or if you have not followed Battery Care instructions your battery may be dead If you are unsure whether or not the battery are dead you can have it tested at your local Power Wheels authorized service center The electrical switches can become corroded due to exposure to water or moisture or can jam due to loose dirt sand or gravel Contact your local Power Wheels authorized service center for diagnosis and repair Contact your local Power Wheels authorized service center for diagnosis and repair 24 PROBLEMS AND SOLUTIONS GUIDE POSSIBLE PROBLEM CAUSE Vehicle was running but Loose wires or loose Suddenly stopped connectors Tripped thermal fuse short run time Less than Undercharged battery 1 3 hours per charge Overcharged battery Battery is old and will not accept full charge Tripped thermal fuse Vehicle runs in low speed High speed lock out not but does not run in disconnected high speed Please Note The vehicle is designed to operate in low speed only in reverse SOLUTION Check all wires and connectors Make sure the battery suddenly Stopped connector is tightly plug
15. ged into the motor harness connector and that there are no loose wires around the motors The built in thermal fuse may trip and shut down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe Once a fuse has tripped remove your foot from the pedal and wait 25 seconds before opperating the vehicle again To avoid repeated automatic shutdowns do not overload the vehicle by exceeding the 130 Ibs 59 kg maximum weight capacity or by towing anything behind the vehicle Do not drive up hills or run into fixed objects which can cause the wheels to stop spinning while power is still being supplied to the motors If a thermal fuse continually trips contact your local Power Wheels authorized Service center Charge the battery A new battery should have been 1 3 hours per charge charged for at least 18 hours before using the vehicle for the first time After first time use recharge the battery for at least 14 hours after each use Never charge the battery longer than 30 hours Check all wires and connectors Make sure the battery connector is tightly plugged into the charger connector and that the charger is plugged into the wall Make sure power flow to the wall outlet is ON Do not charge the battery longer than 30 hours If you suspect that your battery is damaged as a result of overcharging contact Consumer Relations They can test the battery for you Even with proper care
16. he vehicle This warranty covers normal use and does not cover the Power Wheels vehicle or battery if damaged by unreasonable use neglect accident abuse misuse improper service or other causes not arising out of defects in materials or workmanship Evidence of any attempt at consumer repair will void this warranty THIS WARRANTY DOES NOT COVER AND IS INTENDED TO EXCLUDE ANY LIABILITY ON THE PART OF POWER WHEELS WHETHER UNDER THIS WARRANTY OR IMPLIED BY LAW FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES FOR BREACH OF WARRANTY SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION SO THIS LIMITATION MAY NOT APPLY TO YOU Should you need service or assistance with your vehicle during the warranty period do not return the vehicle to the store Power Wheels has provided a nationwide network of authorized service centers If there is not an authorized service center in your area please visit us on line at www powerwheels com or call Consumer Relations for information 1 800 348 0751 This warranty gives you specific legal rights and you may also have other rights which may vary from state to state PLEASE SAVE YOUR ORIGINAL SALES RECEIPT W2602pr 0920 PROBLEMS AND SOLUTIONS GUIDE IMPORTANT If you experience a problem with your vehicle first check the Problems and Solutions Guide below If you still experience a problem please contact Power Wheels Consumer Relations or your local Power Wheels authorized service center
17. ive wear or damage each time you charge the battery If damage or excessive wear is detected do not use the charger or the battery until you have replaced the worn or damaged part HOT motors Handle carefully RIDING HAZARD WARNING Prevent Injuries and Deaths Direct Adult Supervision Required e Never Ride at Night e Keep Children Within Safe Riding Areas These areas must be Away from swimming pools and other bodies of water to prevent drownings Generally level to prevent tipovers Away from steps steep inclines cars roads and alleys Hiding Rules Make sure children know and follow these rules for safe driving and riding Always sit on the seat Always wear shoes Only 2 two riders at a time W2602pr 0920 2 IMPORTANT INFORMATION e Read this manual carefully for important safety information and operating instructions before using your vehicle Keep this manual for future reference as it contains important information The vehicle is designed for use on grass asphalt and other hard surfaces on generally level terrain and by children 3 years of age and older Do not exceed the maximum weight capacity of 130 Ibs 59 kg Your new vehicle requires adult assembly Please set aside at least 45 minutes for assembly Use this vehicle ONLY outdoors Most interior flooring can be damaged by riding this vehicle indoors Fisher Price will not be responsible for damage to the floor if the
18. n vehicle use and use conditions Replace only with a Power Wheels 12 Volt battery with built in thermal fuse Do not substitute parts Make sure you do not overload the vehicle by allowing more than one rider at one time exceeding the 130 Ibs 59 kg maximum weight capacity or by towing objects behind the vehicle If the vehicle is overloaded the built in thermal fuse in the battery may trip and automatically shut down Adjust the driving conditions to prevent repeated automatic shutdowns Use only on generally level ground Check all wires around the motors and all connectors to run but other times it does make sure they are tight Contact your local Power Wheels authorized service center for diagnosis and repair 26 PROBLEMS AND SOLUTIONS GUIDE PROBLEM When the foot pedal is pressed the vehicle won t run without a push Battery s thermal fuse constantly trips but the vehicle is not overloaded nor the driving conditions too severe Loud clacking or grinding noise from a motor gearbox Charger gets warm during use Battery makes a sizzling or gurgling noise when charging POSSIBLE CAUSE Loose wire or connector Dead Spot on motor Damaged battery Child is switching between FORWARD and REVERSE without stopping Broken gears It is normal for some chargers to get warm during use and is not reason for concern some chargers do not get warm during use It is normal for some ba
19. ng of this product with household waste 2002 96 EC Check your local authority for recycling advice and facilities Europe only e Return an exhausted battery to a federal or state approved lead acid battery recycler such as a Power Wheels authorized service center or a local seller of automotive batteries Contact your local waste management officials for other information regarding the environmentally sound collection recycling and disposal of lead acid batteries If you live in the State of Florida or the State of Minnesota it is prohibited by law for anyone to throw away lead acid batteries in the municipal waste stream W2602pr 0920 22 ICES 003 This Class B digital apparatus complies with Canadian ICES 003 Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NMB 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada L utilisation de ce dispositif est autoris e seulement aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 l utilisateur du dispositif doit amp tre pr t accepter tout brouillage radio lectrique recu m me si ce brouillage est susceptible de compromettre le fonctionnement du dispositif VEHICLE CARE e Check all screws and their protective coverings regularly and tighten a
20. pedal W2602pr 0920 BATTERY CARE If a battery leak develops avoid contact with the leaking acid and place the damaged battery in a plastic bag See next section for proper disposal If acid comes in contact with skin or eyes flush with cool water for at least 15 minutes and call a physician If acid is internally ingested give water milk of magnesia or egg whites immediately Never give emetics or induce vomiting Call a physician Do not allow the battery to run down completely before charging e Charge the battery before storing the vehicle and at least once per month even if the vehicle has not been used e Charge the battery after each use regardless of how long the vehicle was used e Leaving the battery in a discharged condition will ruin it e Always remove an exhausted battery from the vehicle Battery leakage and corrosion can damage the vehicle Do not store the battery in temperatures above m 75 F or below 10 F LY BATTERY DISPOSAL e Your Power Wheels battery is a non spillable sealed lead acid battery It must be recycled or disposed of in an environmentally sound manner e Do not dispose of a lead acid battery in a fire The battery may explode or leak e Do not dispose of a lead acid battery in your regular household trash The incineration landfilling or mixing of sealed lead acid batteries with household trash is prohibited by law in most areas e Protect the environment by not disposi
21. s required Check plastic parts on a regular basis for cracks or broken pieces e During snowy or rainy weather the vehicle should be stored inside or under a protective cover e Avoid operating the vehicle in wet or snowy conditions Water or moisture in the motors or electrical switches can cause them to corrode and could cause switch or motor failure Avoid operating the vehicle on sand loose dirt or gravel Sand loose dirt or gravel in the motors or electrical switches can cause them to jam and could cause switch or motor failure e The vehicle can be wiped down with a soft dry cloth For a shiny finish you can wipe plastic parts with a non wax furniture polish applied to a soft cloth Do not use automotive wax Do not use soap and water or spray the vehicle with a hose e To ensure your vehicle stays in good operating order we recommend you periodically have your vehicle checked by a Power Wheels authorized service center 23 LIMITED WARRANTY Bumper to Bumper Limited Warranty One year limited warranty from the date of purchase on the Power Wheels vehicle Six month limited warranty on the 12 volt battery For the original purchaser this one year limited warranty covers the Power Wheels ride on vehicle purchased from Power Wheels against defects in materials and workmanship The six month limited warranty applies only to the 12 volt battery included by Power Wheels with the original purchase of t
22. sult in serious injury e Never allow children to charge the battery Battery charging must be done by adults only A child could be injured by the electricity involved in charging the battery e Read the safety instructions on the battery e Examine the battery charger and their connectors for excessive wear or damage each time you charge the battery If damage or excessive wear is detected do not use the charger or the battery until you have replaced the worn or damaged part N CAUTION Use the charger in dry locations only e Make sure you charge the battery for at least 18 hours using the enclosed Power Wheels 12 volt charger before operating your vehicle for the first time Charge the battery for at least 14 hours after each use of the vehicle Never charge the battery longer than 30 hours Failure to follow these instructions may damage your battery and will void your warranty e Use only a Power Wheels 12 volt charger with 12V connector input 120 VAC 60Hz with an output of 12 VDC to charge your Power Wheels 12 volt battery Charger SR y Charger Connector e Plug the charger connector into the battery socket e Plug the charger into a standard wall outlet Notes f power flow to the wall outlet is controlled by a switch make sure the switch is ON Use the charger only in a wall outlet Do not plug the charger into a ceiling outlet e Before charging the battery examine the
23. ttel Inc All Rights Reserved and designate U S trademarks of Mattel Inc PRINTED IN MEXICO W2602pr 0920
24. tteries to make noise and swell slightly while charging and is not reason for concern SOLUTION Check all wires around the motors and all connectors the vehicle won t run without to make sure they are tight Contact your local Power Wheels authorized service center for diagnosis and repair Contact your local Power Wheels authorized service center for diagnosis and repair Teach your child to stop the vehicle before switching direction Contact your local Power Wheels authorized service center for diagnosis and repair No action required If your charger does not get warm during use it does not mean that it is not working properly No action required If your battery does not make noise or swell slightly during charging it does not mean that it is not accepting the charge 27 W2602pr 0920 Before first time use you must charge the battery 18 hours Charge the battery immediately after each use Charge the battery once a month even if the vehicle is not used or stored Do not return your vehicle to the store We re a toll free phone call away and we can help If you are missing parts or need assistance please call 1 800 348 0751 Or contact your local independently owned and operated Power Wheels Authorized Service Center For the location nearest you visit us on line at Www powerwheels com Fisher Price Inc a subsidiary of Mattel Inc East Aurora NY 14052 U S A 2011 Ma
25. use VEHICLE OPERATION Help your child practice steering to learn how far and how quickly to turn the steering wheel when driving and automatically knows how to stop Beginner Use Low Speed e Make sure the shifter is in the low speed position e Press down on the foot pedal IMPORTANT To avoid damaging the motors and gears Stop the vehicle before shifting from forward to reverse e Make sure the shifter is in the reverse position e Press down on the foot pedal The vehicle is designed to operate in low speed only in reverse e Your vehicle has a patented electronic braking system that automatically stops the vehicle when your child s foot lifts from the pedal 21 Advanced Use High Speed Place lock out screw here for storage Remove lock out screw for high speed e Before you disconnect the high speed lock out make sure your child knows how to steer start and stop the vehicle and knows the safe driving rules When the high speed lock out is disconnected the vehicle can be driven forward in low 2 mph 4 km hr maximum or high speed 5 mph 8 km hr maximum e Make sure the shifter is in the reverse W position oosen and remove the screw in the shifter base e Replace the lock out screw into the hole in the shifter for future use It can be re inserted into the shifter base to lock out high speed e Make sure the shifter is in the high speed lI position e Press down on the foot
26. vehicle is used indoors You must charge your battery for 18 30 hours before you use your vehicle for the first time We recommend charging your battery before beginning assembly Please see the Battery Charging section for detailed instructions The battery charger is not a toy Do not short circuit the battery Adults Note Regularly examine the charger for damage to the cord plug housing or other parts that may result in the risk of fire electric shock or injury In the event of any damage do not use the charger until the damage has been properly repaired Your Power Wheels 12 volt battery is equipped with a built in thermal fuse The thermal fuse is a self resetting safety device which automatically trips and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe Once a fuse has tripped remove your foot from the pedal and wait approximately 25 seconds before operating the vehicle again To avoid repeated automatic shut downs avoid severe driving conditions If a thermal fuse in a battery continually trips under normal driving conditions please contact your local Power Wheels Authorized Service Center To prevent damaging the motors and gears teach your child to stop the vehicle before switching direction If you have any questions about your Power Wheels vehicle please call our toll free service lines at 1 800 348 0751 Trained customer service representatives
27. y to fit both the steering column post into the e Fit the steering column through the hole in the hole in the floor of the vehicle and the steering column Steering linkage SME SOL pe O ri EN OLGEN G e Fit a s 1 cm lock nut onto the end of the steering column and tighten with the assembly wrench Steering Column e Push the steering column down so that it inserts into the slot in the steering linkage underneath the vehicle Screws f mmm e Insert four 8 x 1 9 cm screws into the holes in the bottom of the vehicle to hold the steering column post and seat and tighten 15 W2602pr 0920 ASSEMBLY Steering Wheel Steering Wheel Cap e Fit the steering wheel cap to the center of the steering wheel Push to snap into place e Turn the vehicle upright e Fit the steering wheel onto the steering column assembly Hint The steering wheel is designed to fit the steering column one way If it does not seem to fit turn it around and try again Steering Column Lock Nut Assembly Wrench e Fit a s 1 cm lock nut onto the end of the steering column and tighten with the assembly wrench W2602pr 0920 16 DECORATION e Before applying the labels wipe the surface of the vehicle with a clean dry cloth to remove any dust or oils e Place the labels exactly as shown in the illustrations For best results avoid repositioning a label once it has been applied to the vehicle e After applying a lab
Download Pdf Manuals
Related Search