Fisher-Price 79652 Instruction Sheet
Contents
1. Fisher Price Bounce n Play Activity Dome Model Number 79652 Please keep this instruction sheet for future reference as it contains important information Tool needed for assembly Phillips Screwdriver not included Use only for a child who is unable to push up on hands and knees pull up or sit unassisted Product features may vary from picture above Warnings A WARNING Failure to follow these warnings and instructions could result in serious injury or death To reduce the risk of Sudden Infant Death Syndrome SIDS normal healthy infants should always sleep on their backs unless otherwise advised by a pediatrician e Infants can suffocate In gaps between an extra pad and side of the dome On soft bedding Never add a mattress pillow comforter or padding Use ONLY the pad provided by the manufacturer To prevent falls Do not use this product when infant begins to push up on hands and knees Never place product on an elevated surface To prevent strangulation Never place items with strings such as hood strings or pacifier cords around a child s neck Never place product near a window where cords from blinds or drapes can strangle a child Never move this product with child in it e Never leave child unattended Consumer Information Occasionally a consumer may experience a problem with one of our products If this should happen please call us toll free rather than ret2. anopy stay through the canopy tunnel Frame Middle Hole Middle Hole Frame Tubes Position the ends of the frame tubes against the middle holes in a frame Rounded Side H N7 M6 x 1 Screw 4 M6 Lock Nut 4 M6 Lock Nut Frame Tube Q Push Base Up Insert an M6 x 15 s screw through each frame tube and into the frame e Fit an M6 lock nut with the rounded side toward the fabric into each middle hexagonal opening on the back of the frame Hint You may find it easier to access the hexagonal opening on the back of the frame if you push the base up so that the fabric is out of the way Assembly Tighten the screws with a Phillips screwdriver Do not over tighten e Repeat assembly steps 3 5 to attach the other ends of the frame tubes to the frame on the other side of the base MAMA CAOIL e Fit an M6 lock nut with the Rounded Side rounded side toward the M6 Lock Nut 4 ae i Monee SEEN apanga fabric into each lower hexag onal opening on the back of the frame Tighten the screws with a Phillips screwdriver Do not over tighten e Repeat this procedure to attach the other ends of the base wires to the frame on the other side of the base Base Wire Base Wire e Position the base wires around the base so that the ends point upward and are against the lower holes in a frame Place a spring onto an M6 x 15 8 screw Insert the M6 x 1 s screw with spr
3. base base wire rotate down s 5 i wire should rest in the groove in Note If the base wire does not freely rotate down pull the each frame sides of the base wire further outward Repeat Use steps 1 3 to unfold the other base wire Using the Canopy Sides of Base Wire Lift the product up slightly so that each side of the base wire snaps into the groove in each frame Make sure you hear a snap Adjust the canopy up or down Use Using the Mesh Cover Zipper Mesh Cover Up I CX e Adjust the canopy and mesh cover up e While holding the mesh cover up fasten the zipper closed To Fold for Portability Sides of Base Wire e Grasp both sides of a base wire e While lifting the product up slightly pull both sides of the base wire outward to remove the base wire from the groove in each frame Fisher Price Inc a subsidiary of Mattel Inc East Aurora NY 14052 U S A 2001 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Use Base Wire e Rotate the base wire up e Repeat this procedure to fold the other base wire Care The pad and toys are machine washable Wash the pad and toys separately in cold water on the gentle cycle Do not use bleach Tumble dry separately on low heat and remove promptly The fabric and frame may be wiped clean using a mild cleaning solution and a damp cloth For other countries outside the United S
4. ing through a base wire and into the frame Assembly Rounded mA Side o H M5 x 18 16 Screw 2 lt 7 M5 Lock Nut 2 Metal Canopy Stay Position one end of the metal canopy stay against the upper hole in a frame Insert an M5 x 113 16 screw through the hole in the cover Fit the end of the screw through the hole in the metal canopy stay and into the upper hole in the frame Push on the cover to insert and snap the tab on the cover into the slot in the frame Make sure you hear a snap Fit an M5 lock nut with the rounded side toward the fabric into the upper hexagonal opening on the back of the frame Tighten the screw with a Phillips screwdriver Do not over tighten Repeat this procedure to attach the other end of the metal canopy stay and the remaining cover to the frame on the other side of the base 2 Canopy Fasteners e Fasten the pad fasteners to the base fasteners Lift the canopy Attach the toys to the canopy fasteners IMPORTANT Assembly is now complete but Bounce n Play Activity Dome is not ready for use Please refer to the Use instructions on this page beginning with step 2 Use To Unfold Sides of Base Wire Position the product upright on a flat surface Grasp both sides of a base wire Push down on the product to be sure each side of the base wire is e Pull both sides of the base wire outward and then let the in the correct position The
5. tates Canada call 1 800 567 7724 or write to Mattel Canada Inc 6155 Freemont Blvd Mississauga Ontario L5R 3W2 Great Britain telephone 01628 500303 Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 New Zealand 16 18 William Pickering Drive Albany 1331 Auckland Printed in China 79652pr 0920
6. urn this product to the store Usually we can solve the problem over the telephone or send you replacement parts Please call Fisher Price Consumer Relations toll free at 1 800 432 KIDS 8 AM 6 PMEST Monday through Friday Hearing impaired consumers using TTY TDD equipment please call 1 800 382 7470 Or write to Fisher Price Consumer Relations 636 Girard Avenue East Aurora New York 14052 Metal Canopy Stay y 3 Toys F Toys may be different than shown G ND Spring 4 Plastic Mesh Cover Stay M5 x 18 16 Screw 2 CAUTION This product contains small parts in its unassembled state Adult assembly is required 3 M5 Lock Nut 2 M6 Lock Nut 8 M6 x 15 s Screw 8 ALL SHOWN ACTUAL SIZE Assembly IMPORTANT Before each use or assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Fisher Price for replacement parts and instructions if needed Never substitute parts Button Hole Plastic Mesh Cover Stay Open the base and position it upright on a flat surface as shown e Locate the end of the base with the mesh cover Insert the entire plastic mesh cover stay into one of the button holes in the mesh cover Be sure to tuck the plastic mesh cover stay away from the button hole in the mesh cover Metal Canopy Stay Insert the metal c
Download Pdf Manuals
Related Search