Extron electronic DVI Output Card User's Manual
Contents
1. switches or other electronic components inside the switcher Doing so could damage the switcher Electrostatic discharge ESD can damage IC chips even though it cannot be felt A grounding wrist strap is recommended 6 Disconnect the two fan power cords from connectors J8 and J13 on the main board 7 Remove the top cover and set it aside 1 DVI Output Card Installation Installation cont d CN Og Lift cover straight up T Remove 16 screws Remove top two front panel screws f d A S j N Fan Connectors MU a NS DVI card socket J14 J8 and J13 Zi S Figure 1 Removing the switcher cover DVI Output Card Installation Installation cont d DVI Output Card Installation Install the DVI output card in the switcher as follows WARNING Changes to electronic components must be performed by authorized service personnel only MENNA To prevent electric shock always unplug the switcher from the AC power source before opening the enclosure 1 Locate the DVI output card connector opening on the rear panel and the DVI output card socket J14 on the left rear portion of the main circuit board as viewed from the front figure 2 Rear Panel DVI Output Card Connector Opening DVI Output Card Socket J14 on Main Circuit Board Figure 2 DVI output card connector opening and socket J14 DVI Output Card Installation Installation cont d 2 Ifthe rear panel DVI connect2. USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX Inside USA Canada Only 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 1 714 491 1500 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX 1 714 491 1517 FAX 2009 Extron Electronics All rights reserved
3. cf Ase Extron Electronics IGN INTERFACING SWITCHING AND DISTRIBUTION Cal lt urio Installation Guide HN Qn EXTRON ELECTRONICS COPYRIGHT PCB ASSY 20 MADE IN USA a DVI Output Card Digital Visual Interface Card for ISS 108 408 and ISM 482 68 761 01 Rev B 0109 Installation An optional digital visual interface DVI output card is available for the ISS 108 ISS 408 and ISM 482 With the card installed the switcher outputs Program video simultaneously on the standard DVI connector and Program Output BNC and 15 pin HD connectors Opening the Switcher Extron recommends returning the switcher to Extron for service and updates NOTE The ISM 482 Switcher installation is shown The ISS 108 and ISS 408 installations are similar To install the optional DVI output card the switcher case must be removed Remove as follows 1 Disconnect the AC power cord to remove power from the switcher MENNA To prevent electric shock always unplug the switcher from the AC power source before opening the enclosure 2 Ifthe switcher is installed in a rack disconnect all signal and control cables and remove the switcher from the rack 3 Remove the 16 screws from the switcher 8 on the top and 4 on each side of the cover figure 1 4 Remove the top two front panel screws 5 Lift the top cover straight up approximately five inches for access to the fan power cords Do not touch any
4. or opening is covered remove the two screws that secure the cover to the back panel and remove the cover 3 Position the DVI card above J14 with the DVI connector facing toward the rear of the switcher Ensure the pins on the DVI card properly align with the J14 socket to prevent bending 4 Carefully insert the DVI board 45 pin connector into socket J14 on the main circuit board figure 3 DVI Output Card DVI Output Card DVI Connector DVI Output Card Mated to the Main Board via Socket J14 Figure 3 Output DVI board installation 5 Secure the DVI card to the rear panel with the two screws provided in the kit ZALO Carefully inspect the pins to be certain all are properly seated in the socket before proceeding The board connector should have all pins inserted the same depth DVI Output Card Installation Installation cont d Closing the Switcher 1 Reconnect the two fan power cords to connectors J8 and J13 on the main board It does not matter which fan is connected to which connector 2 Replace the top cover on the switcher 3 Fasten it with the screws that were removed in Opening the Switcher step 3 and step 4 4 Reinstall the switcher and reconnect all cables Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters a 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 883 1568 971 4 2991800 800 633 9876 Inside
Download Pdf Manuals
Related Search