Epson PriorityFAX 1000 Product Support Bulletin
Contents
1.2. TABLE 2 Switch 4 Direct connection mode When switch 4 is set to 1 the unit starts receiving signals from the remote station when the START COPY key is pressed regardless of whether the hand set is on hook or off hook This mode is used for cross testing two fax machines when they are connected directly to each other TABLE 3 Switches 1 4 Stan End Transmission speed in 63 mode The starting and ending transmission speed can be set separately in 63 overseas communication mode If there is excessive noise decrease the starting speed Increase the ending speed if the transmission of the document takes too long These settings are independent of the overseas communications mode Table 2 switches 2 and 3 PSB No P 0071 Page 5 of 7 TABLE 4 Switches 3 amp 4 Modem Equalizer These switches are used for setting the modem equalizer to compensate for line loss The function section of Table 4 lists the relationship between the line loss and the appropriate switch setting that compensates for that loss TABLE 4 Switches 5 8 Modem Attenuator These switches are used to adjust the transmission level attenuation The amount of attenuation is accumulative when setting more than one switch to 1 For example if switches 5 and 6 are set to 1 and switches 7 and 8 are set to 0 the accumulative attenuation is 12 dB The maximum attenuation with all the switches set to 1 is 15 dB Hat switch in this sect
3. COPY buttons until the buzzer stops sounding sets the PF1000 into an error code display mode In the error code display mode the state of the SENDING DOCUMENT RECEIVING DOCUMENT FINE and PHOTO LEDs on the front panel reflect the error condition of the PF1000 If an LED is ON it represents a 1 if it is OFF it ore a 0 Use Columns 0 through 7 of Table 1 to interpret the error code The LEDs display the error code in 2 parts The state of the ADD PAPER LED which changes in 5 second intervals determines which part of the error code is being displayed 1 When the ADD PAPER LED is ON the PHOTO FINE RECEIVE DOCUMENT and SEND DOCUMENT LEDs represent columns 0 1 2 3 of Table 1 2 When the ADD PAPER LED is OFF the PHOTO FINE RECEIVE A and SEND DOCUMENT LEDs represent the columns 4 5 6 7 of Table 1 PSB No P 0061 Page 2 of 3 For example if a document is being sent and is not detected by document sensor 2 the PF1000 will go into error mode Simultaneously pressing and holding the FINE PHOTO and the START COPY buttons until the buzzer stops sounding sets the PF1000 into an error code display mode In this error condition when the ADD PAPER LED is ON only the PHOTO and FINE LEDs will be ON In Table 1 This is interpreted as a 1 for columns 0 and 1 and a 0 for columns 2 and 3 When the ADD PAPER
4. LED is OFF only the SEND DOCUMENT and FINE LED s will be ON In Table 1 this is interpreted as a 1 for columns 5 and 7 and a 0 for columns 4 and 6 In Table 1 locate the Row that has a 1 in columns 0 1 5 and 7 and a 0 in columns 2 3 4 and 6 Notice that this row corresponds to the same row that lists the Doc sensor 2 not detecting document error PSB No P 0061 Page 3 of 3 Table 1 EQUIPMENT ERROR CODES ADD PAPER LE STATE SD RD FN Oor o PH sano aso no vl aT al st aba ala ol Paper jam error SENDING DOCUMENT LED RECEIVING DOCUMENT LED FINE LED PHOTO LE D Error Codes Auto cutter jam error Head connector open error Thermistor heat error Paper low sensor output too low Paper low sensor to high Paper low sensor output unstable japer low sensor black and white error Recording paper cover open 1 of of ofo f ERELLO a ip of o of a a Doc sensor 2 not detecting document 1 11 0 1 o ol Faulty white level data Faulty DMAO in scanning al of ofif of PORE ai Faulty DMA1 in scanning EREKE 1 Document feed time out 1 line scanning time out CECA TEE Over heating of power supply alal 2 of o 1l o Ol Out of recording paper af af af of ol 1 1 o White level data error in EEPROM 1 1 1 OF 1 o 1 o Document lost during transmission
5. OP to exit a different switch bank second level switches ee Press STOP to exit Initial Maintenance Mode Returns the unit to normal KKK operation Figure 2 iteh Function r Description l o E PARAMETER INITIALIZATION EEPROM WHITE LEVEL DATA INITIALIZATION 08 XMT VERIFICATION OFF o KOT USED CAC SECONO LEVEL SWITCH FUNCTIONS SECOND LEVEL SWITCH DATA PRINTOUT PSB No P 0071 Page 7 of 7 Switch Oeser iption Setting Function OVERSEAS COMMUNICATION O OFF RODE Reception OVERSEAS COMMUNICATION MODE Tranemission OFF gnores OIS once Tranemits 1100Hz tps at the start of G3 communications mode Switch Switch jmber Oescription setting Function 1 2 sotuse i r MODEM EQUALIZER Mote The Line Loss shown is Aom onimemtiamat an da hati nai tet AQ dan dii be ia Sa ne dit RA Mal ci Sci Bile cS it hn Ach ea le Sant Sn i Tal a a i akc ai abate Se zanan WEFORMATION Product Support Bulletin Subject PriorityFax 1000 Equipment Error Codes Date 3 7 90 PSB No P 0061 Page 1 of 3 Originator VB This product support bulletin explains the procedure for reading and interpreting PriorityFax 1000 PF1000 error codes m TEORY equipment error codes are listed under the Error Codes column in able 1 When the PF1000 is in error mode the buzzer sounds and the ERROR LED turns ON Simultaneously pressing and holding the FINE PHOTO and the START
6. White Level Data Initialization enter the initial maintenance mode Load a blank white sheet of paper in the document slot 2 Press the START COPY key twice and then press the FINE PHOTO key one time 3 Upon completion of the white level data initialization the unit will emit cae long beep indicating it has returned to the initial maintenance mode PSB No P 0071 Page 3 of 7 TRANSMISSION VERIFICATION REPORT 1 To set the Transmission Verification Report to ON enter the initial maintenance mode Press the START COPY key 7 times and then press the FINE PHOTO key one time To set the Transmission Verification Report to OFF enter the initial maintenance mode Press the START COPY key 8 times and then press the FINE PHOTO key one time 2 Upon completion the unit will print the change made and emit one long beep indicating it has returned to the initial maintenance mode TEST PATTERN 1 To print the test pattern shown in Figure 1 enter the initial maintenance mode Press the START COPY key 9 times and then press the FINE PHOTO key one time 2 Upon completion of the test pattern print out the unit will emit one long beep indicating it has returned to the initial maintenance mode SECOND LEVEL SOFT SWITCH FUNCTIONS The second level of soft switch functions is accessed through switch 10 of the initial level of function switches Refer to Figure 2 for instructions
7. e first digit of the Switch Number to be selected To enter zero press the START COPY key10 times C To complete the code entry press the FINE PHOTO key one time D The unit returns to the initial maintenance mode when the number entered does not correspond to a function listed in Table 1 PSB No P 0071 Page 2 of 7 E Pressing the STOP key in the initial maintenance mode returns the unit to normal operation Pressing the STOP key when only one digit has been entered returns the unit to normal operation F The functions in Table 1 marked NOT USED are either not available or require specialized equipment They should only be accessed by an authorized Epson Customer Care Center EEPROM PARAMETER INITIALIZATION Function Sets the EEPROM memory content user switch data and soft switch data to the factory default settings Operation Method 1 To activate the EEPROM Parameter Initialization enter the initial maintenance mode Press the START COPY key one time and then press the FINE PHOTO key one time 2 Upon completion of the parameter initialization the unit will emit one long beep indicating it has returned to the initial maintenance mode EEPROM WHITE LEVEL DATA INITIALIZATION Function The unit scans a blank white sheet of paper to establish a while level reference point that is used for comparison of black and white levels Operation Method 1 To activate the EEPROM
8. ion of Table 4 is set to 0 that switch value is O dB E ee nee u ESENE R ee ee m neen E SCR PEER REESE SESE ES ee ee Figure 1 PSB No P 0071 Page 6 of 7 To enter Initia Maintenance Mode Hold down the FINE PHOTO and START COPY buttons while applying Dower Initial Maintenance Mode Press FINE PHOTO 1 time Press START COPY 10 times Press FINE PHOTO 1 time Sets second digit to 1 Sets first digit to 0 Completes code entry Second level switches accessible OPTI ONAL Press the FINE PHOTO Button 1t Table 2 To print a SYSTEM 1 2 or 3 times to select 2 Table 3 CONFIGURATION LIST 3 Table 4 Press FINE PHOTO 1 time the desired switch bank See Tables 2 3 and 4 H Press START COPY 1 time Press FINE PHOTO 1 time Enters selection Prints current switch status Press the START COPY button Press the FINE PHOTO Button the number of times equal to the soft switch to be changed Press the START COPY button Enters selection Press the FINE PHOTO button once to select t Skipthis Refer to table 2 3 or 4 for step to select 0 more detail Refer to the System configuration listortable 2 3 or 4 Press the START COPY button Enters selection Press START COPY to set Press STOP to exit Pressing STOP will print other switches current switch bank switch status Press START COPY to select Press ST
9. on accessing and changing these functions SECOND LEVEL SOFT SWITCH DATA PRINTOUT 1 To print the System Configuration List which contains the Second Level Soft Switch Data enter the initial maintenance mode Press the PHOTO FINE key one time press the START COPY key one time and then press the PHOTO FINE key one time 2 The unit will print the System Configuration List and emit one long beep indicating it has returned to the initial maintenance mode PSB No P 0071 Page 4 of 7 SECOND LEVEL SOFT SWITCH FUNCTION DESCRIPTIONS TABLE 2 Switch 1 Overseas communication mode reception Setting switch 1 to a 1 allows the unit to acknowledge the 1100 Hz signal that suppresses echoes instead of a 2100 Hz which disables the echo suppressor ES Suppressing the echoes provides a more reliable method of establishing communications TABLE 2 Switches 2 amp 3 Overseas communication mode Transmission When switch 2 is set to 1 and switch 3 is set to O the unit ignores the DIS signal sent from the calling station for suppressing echoes Note Some called models may cause an error by receiving an echoed DIS When both switches 2 and 3 are set to 1 the unit transmits an 1100 Hz signal for 3 seconds upon detection of the DIS V 21 flag This operation prevents the called station from receiving its own DIS and enables a no carrier state until the unit transmits a subsequential DIS
10. sama INFORMATION Product Support Bulletin Subject Priority Fax 1000 Maintenance Switch Function Tables Date 8 8 90 PSB No P 0071 Page 10f7 Originator VB The purpose of this document is to describe the PriorityFax IO00 maintenance soft switch functions and to supply instructions for accessing them ACCESSING THE MAINTENANCE MODE 1 To enter the maintenance mode apply AC power while pressing the FINE PHOTO and the START COPY keys 2 The unit will output a long beep and the ERROR LED will blink indicating the unit is in maintenance mode If the unit does not enter the maintenance mode call Epson Product Support at 213 539 9955 for assistance 3 There are 2 levels of soft switch functions accessible in the maintenance mode Table 1 lists the initial level functions Tables 2 3 and 4 list the second level functions The tables are located at the end of this document 4 The following operations explain how to execute the first level soft switch functions listed in Table 1 A In Table 1 the second digit of the Switch Number is the number on the left To enter a 1 as the second digit of the Switch Number press the FINE PHOTO key once At this point If the FINE PHOTO key is not pressed before the START COPY key the second digit remains as zero B To Enter the first digit of the Switch Number press the START COPY key the number of times equal to th
Download Pdf Manuals
Related Search