Epson 455Wi Operation Guide
Contents
1. Actual monitor image Image of virtual display1 Image of virtual display2 Caution When using multiple projectors placed side by side note the following points as the combined effect of the air exhausted from the projectors may generate a high temperature warning e Use the projectors in an environment of 35 C or lower e Use a display that is larger than 50 for projection e Make sure that there is a space of more than 60 cm between the projectors e Do not setup the projectors in a location where they are exposed to direct sunlight or air from an air conditioner or heater or any other location subject to high temperatures Using Multi Screen Display Arrangement example 2 Example of Adjusting the Virtual Display By arranging the virtual display allocation you can project only the image that you want to show or project different images from left to right in a presentation Arrangement example 1 Actual monitor image PowerPoint file presenter tools Image of virtual display Slide Show using a PowerPoint file Actual monitor image PowerPoint file Image of virtual2. lt Click Connect In a Windows environment you cannot view the image being sent to a virtual display on the computer To adjust the image on the vir a ee al tual display you must do so while viewing the projected image C Disable interrupt connection A Se To perform mouse based operations on the virtual display move nition l l o l the mouse pointer in the direction of the virtual display such that ___ Troubleshooting J Zea the pointer appears on the virtual display Display layout We To terminate multi screen display click Disconnect on the toolbar AON In a Windows environment if the virtual display driver has been enabled 4 such that the mouse pointer can be moved outside the limits of the screen there may be occasions when you lose track of the location of the pointer If you are not using a virtual display clear the virtual display checkbox on the Add Remove Virtual Display screen so that the mouse pointer moves back inside the screen s display area To subsequently use multi display again place a check mark against the required display under Add Remove Virtual Display To clear a check mark see the following p 23 Connecting to a Projector on a Different Subnet Connecting to a Projector on a Different Subnet e When you use Manual search in Quick Connection Mode you can specify This chapter explains
3. Search method on startup Edit profile The Edit profile dialog box is displayed p 34 Switch LAN Restore Defaults Set whether or not the Quick Connection Mode Advanced Connection Mode screen is displayed when EasyMP Network Projection starts Clear this checkbox once you have settled on a regular startup method Set whether or not the Quick Connection Mode Advanced Connection Mode screen is displayed when EasyMP Network Projection starts Because this projector always starts in Advanced Connection Mode clear this checkbox Select from the following projector search methods executed when EasyMP Network Projection is started Automatic search on startup Specify search method after startup Search with the last network configuration Windows only The Switch Network Adapter dialog box is displayed This is used when it is necessary to switch the network adapter to be used for a search when a computer has multiple adapters By default all of the network adapters are used to perform a search When a Wired LAN is always used as the connection method select a Wired LAN adapter You can reset all adjustment values for Set options to their default settings However you can retain settings for Edit profile and Switch LAN in General settings Adjust performance tab Set options f 3 a Rear ae E EAE N General settings Adjust performance Fast Audio Output Mormal A C Transfer
4. the screen layout has been fixed 0 00 DELL E2009W Display Arrangement Color To rearrange the displays drag them to the desired position To relocate the menu bar drag it to a different display Using Multi Screen Display Allocating the Image to be Projected Projecting the Allocated Images This section explains the virtual display for arrangement example 1 This section explains the virtual display for arrangement example 1 E p 22 E p 22 Procedure Procedure J Select the number of the virtual display to allocate on the Display and set which image to be projected from which projector S My Y A S a O i j 7 s en the Tile to be projecte O S CTT Start the PowerPoint and Excel files v Drag the window to the desired virtual display monitor and allocate it where the image is to be projected FI EasyMP Network Projection Ver X XxX Advanced Connection JTO Automatic search gt A Manual search Profile Auto egog Drag the Excel window to the right until it cannot be seen As a re sult the PowerPoint window appears on the actual monitor while the Excel window appears on the virtual display on the right Select a projector and connect tt Status Projector name IP address Displa J Standby EMPO2FACT 192 168 11 1 J Standby EMPO2FAC2 192168 11 2 Using Multi Screen Display
5. Keyword displayed on the LAN standby screen and enter the Projector Keyword displayed on the projector screen The selected projector is busy Do you want to continue You tried to connect to a projector that is connected to another computer the connection process When the Yes button is clicked it connects to the projector The connection between the projector and the other computer is cut off When No is clicked it does not connect to the projector The connection between the projector and the other computer is maintained EasyMP Network Projection initialization failed Restart EasyMP Network Projection If the message still appears uninstall and then reinstall EasyMP Network Projection E p 6 Connection failed due to keyword mismatch When connecting to a projector for which a Projector Keyword has been set the wrong Projector Keyword is entered Check the Projector Keyword that is displayed on the projector s connection standby screen After the connection is disconnected and then reconnected enter the Projector Keyword on the keyword entry screen that is displayed p 12 Troubleshooting Network adapter information could not be obtained Check the following point Is a network adapter installed on the computer Is the driver for the network adapter used installed on the computer After checking restart the computer and connect again If you still cannot connect check the following Check the network setting
6. Manualsearch x the next time you perform a search there will be no need to specify the IP address or projector name each time you perform a search For example by creating a group of Profiles for each place where a projector is setup and managing them with folders the target projector can be found quickly The search results are displayed on the EasyMP Network Projec tion projector selection screen Provided the target projector has been identified select that projec tor and then click Connect to establish a connection When you will always be using that projector save the search as a Profile so that you do not have to specify the relevant details every time you perform a search p 32 Performing a Search with a Profile You can save a search for a frequently used projector as a Profile A profile is a file containing all of the information pertaining to a given Building A Floor projector such as the projector name its IP address and SSID If you Building B Floor2 specify that information from the next time you perform a search there Building C Floor3 will be no need to specify the IP address or projector name each time you eae mia perform a search For example by creating a group of Profiles for each Building D place where a projector is setup and managing them with folders the target projector can be found quickly This section explains how to create and edit a Profile Connecting to a Projector on
7. also displayed in Mac OS Procedure 7 Start EasyMP Network Projection For Windows Select Start Programs or All Programs EPSON Projector EasyMP Network Projection EasyMP Network Projection V2 XX For Mac OS Double click the Applications folder of the hard drive volume in which EasyMP Network Projection is installed and then dou ble click the EasyMP Network Projection icon j Select Quick Connection Mode only available when the optional Wireless LAN unit is installed or Advanced Connection Mode and then click OK The projector search results are displayed To always connect using Advanced Connection Mode select Set the selected Connection Mode as the default mode for future connections The projector search results are displayed Because this projector always connects using Advanced Connection Mode select Set the selected Connection Mode as the default mode for future con nections is always selected 2 Select the projector you want to connect to and then click Connect If the projector you want to connect to is not displayed in the search results click the Automatic search button The search takes about 30 seconds For details on the connection screen see Using the Connection Screen p 14 V2 When Projector Keyword is set to On from the projector the Keyword entry screen is displayed Enter the keyword displayed on the LAN standby screen and then click OK Whe
8. eee es 43 The projector is not found when EasyMP Network Projection IS Sta i e PEE eon obra erag E E E EEE teense 43 Cannot connect in Advanced Connection Mode or Wired LAN connection cc cece cece cece eee e eee eeeeenes 45 The Slide Show cannot be displayed on the desired display when the multi screen display function is being executed cee eee 45 Applications are no longer displayed from the computer screen when the multi screen display function is executed 06 45 The mouse cursor is not displayed on the computer screen 46 When connecting with EasyMP Network Projection the image is not displayed or the image is slow tO aPPeEal cece cece cece e eens 46 When a connection is made using EasyMP Network Projection a PowerPoint Slide Show cannot be Started ccc ccc cee eee 46 Before Use This guide describes useful functions for EasyMP Network Projection and how to install the software Functions of EasyMP Network Projection Functions of EasyMP Network Projection You can use EasyMP Network Projection to project your computer screen from the projector via a network Sharing the projector over the network and using various screen transfer functions allow you to hold effective meetings and presentations Sharing the Projector If the projector is connected to a network you can share the projector from computers on the network When projecting data fr
9. how to connect a computer to a projector on a the SSID When there are a lot of projectors you can narrow the search field different sub net via a Wired LAN or a wireless LAN access point on an by using SSID existing network system By default this application only searches for projectors on the same subnet as the computer Therefore even if you perform a search for Specifying Either an IP Address or Projector Name projectors on the network projectors on a different subnet will not be and Performing a Search Advanced Connection found Mode Only You can however identify and connect to a projector on a different subnet as follows In the following explanations unless otherwise noted Windows screen e Specify either an IP address or Projector name and perform a search shots are used The IP Address can be input directly Also provided the Projector The similar screens are also displayed for Mac OS name to be connected has been registered on the DNS server you can perform a search simply by inputting that Projector name p 30 Procedure e Performing a search based on a Profile LC Click Manual search on the EasyMP Network Projection Once you have performed a search for a projector on a different subnet projector selection screen by specifying either an IP Address or a Projector name you can save the search as a Profile with an easy to remember name and then use l EasyMP Network Projection Ver XXX Advanced Connec
10. more information on the utility software see the User s Guide supplied with your LAN adapter For example as shown in the following illustration when a red cross x is displayed over the network icon on the taskbar you cannot connect to the projector For Mac OS Set the network port and communication status For more details on setting the communication status see the User s Guides for your computer or the AirPort card Connecting to a Projector on a Network and Projecting Connecting to a Projector on a Network and Projecting Operating the Projector Before connecting put the projector into connection standby status Make sure the projector network settings are complete and the projector is connected to network equipment such as a network hub via a commercially available network cable Procedure AL Press the button on the remote control to turn the power on lt Press the LAN button on the Remote Control The LAN standby screen is displayed If there is no signal for the current input source it automatically switches to the LAN source If it does not automatically switch to the LAN source press the LAN button LAN Projector Name gt EBXXXXXX IP Address 192 168 100 100 Keyword Connecting to a Projector on a Network and Projecting Operating the Computer In the following explanations unless otherwise noted Windows screen shots are used The similar screens are
11. on the EasyMP Network Projec tion projector selection screen Provided the target projector has been identified select that projec tor and then click Connect to establish a connection Connecting to a Projector on a Different Subnet Managing a Profile Edit the contents registered in the Profile You can change the name and the hierarchical structure of the Profile Edit profile Profile Information on selected profile P roced ure Projector name IP address building A Lie B G EMPOzFACI 192 168 4 251 M building B 1st floor i i H 7 H uilding B 2nd floor 7 EMPO2F AG2 192 168 4 252 Click Set options on the EasyMP Network Projection main oe Le screen i Go EMPozFAC3 192 168 4 253 The Set options screen is displayed Click Edit profile Set options General settings Adjust performance Audio Output Create folder Use full screen video transfer C Encrept communications Display Connection Mode Selection window on startup Search method on startup Automatic search on startup gt Specify search method after startup 0 Search with the last network configuration a m Ci Edit profile D Switch LAN F i TS Indicates a folder F Indicates a Profile The Edit profile screen is displayed Connecting to a Projector on a Different Subnet You can display the registered Profile You can manage it by creating a folder You can change the
12. order of the Profile or the folder by dragging amp dropping You can copy the Profile The copied Profile is saved in the same folder as the original with the Same name You can delete the Profile and the folder Rename You can display the Rename dialog box and rename the folder or the Profile You can enter up to 32 characters in the Rename dialog box Create folder You can create a new folder Exports a created Profile allowing you to import and use that Profile Used when you want to read and use an exported Profile Information on selected profile Projector You can display the projector information name IP ad registered in the Profile dress You can delete the information for the selected projector When all projector information is deleted the profile is also deleted ny S gB S x a 5 Ww Ww y d ny Ww MU ANN Saves your edits and closes the Edit profile screen Using Set options Using Set options You can make setting options such as the processing method when EasyMP Network Projection starts Access Set options from the EasyMP Network Projection main screen Procedure Click Set options on the EasyMP Network Projection main screen Si EasyMP Network Projection Yer X XxX Advanced Connection 2 Automatic search 59 Manual search Profile Auto arf L Soe Select a projector and connect it Status Projector name IP address O GE Standby EMP
13. set and use two or more virtual displays use PowerPoint 2003 or later or limit the number of For Windows virtual displays to one before displaying the Slide Show Applications are no longer displayed from the computer screen when the multi screen display function is executed Check Remedy Is another application running on the virtual display When Virtual Display is installed another application sometimes runs on the virtual display In this For Windows case set Virtual Display to Off in Screen properties Troubleshooting The mouse cursor is not displayed on the computer screen Is Virtual Display installed The mouse cursor was moved onto the virtual display When the virtual display checkbox is cleared For Windows on the Add Remove Virtual Display screen the mouse pointer returns to the screen display area When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear Check Remedy Did you try to play back movies with Media Player or try to Depending on the computer the movie playback screen in Media Player may not be displayed and operate the screen saver preview the screen saver preview may not be displayed normally ls WEP encryption effective or are multiple projectors The display speed decreases when WEP encryption is effective or multiple projectors are connected connected Have you enabled DHCP When DHCP is set to On in Advanced Connection Mode if an available DH
14. 0 110 Save in the profile l Disable interrupt connection et options Use multi display Connect Display layout and Display preferences are added at the bottom of the screen Click Display preferences O Proiectior Adva red onnection OTK FrOJECUON Ver 4 AGVANCeG LONNECION i if syMP Neti EAasyir n e ki po Manual search Profile v futo Automatic search Select a projector and connect it Status Projector name IP address Display g G Standby EPSON PJ 192 168 100 110 2 Save in the profil C Disable interrupt connection et options Use multi display ud Connect p Display layout C Display preferences gt The display setting screen is displayed Using Multi Screen Display Click Arrangement Drag the displayed monitor icon and place it where desired 0 00 DELL E2009W 0 00 Color LCD Display Arrangement Color Display Arrangement Color To rearrange the displays drag them to the desired position Resolutions g play g p To relocate the menu bar drag it to a different display 800 x 500 Refresh Rate 60 Hertz RH 800 x 600 640 x 480 Colors Millions E 1024 x 640 1152 x 864 1152 x 870 Rotate Standard B 1280 x 720 1280 x 800 Show displays in menu bar Mirror Displays Clear the Mirror Displays check box Close the display setting screen Up to this point
15. 8 11 2 C Use multi display E Troubleshooting Oo Pa Automatic search Auto In Advanced Connection Mode you can search for available projectors on the network system to which the computer is connected In Quick Connection Mode you can search for the projector based on the SSID You can search for available projectors on the network system to which the computer is connected Display properties wep Manualsearch In Advanced Connection Mode you can search for a projector based on a specified IP address or projector name In Quick Connection Mode you can search for the projector based on the SSID selected from a list You can search for a projector based on a specified IP address or projector name Connecting to a Projector on a Network and Projecting Status The following six icons indicate the status of the detected projectors Standby Busy fao Select for connecting Select for connecting When you click Connect the computer currently connected is disconnected and your computer is connected Busy Disable Cannot be selected Disable interrupt interrupt connection is set on connection another computer which is already connected at Currently in The projector s Configuration Menu is at use by open You can select it after closing another the Configuration menu and running application the search again _ Searching Displayed while running Manual OD search
16. CP server is not found it may take some time to enter LAN standby status Is Wireless LAN 802 11g b being used in Quick Connection Depending on the electromagnetic wave environment there are times when the image and sound for movies may stop When using the movie sending function use Advanced Connection Mode or Wireless LAN 802 11a in Quick Connection Mode When a connection is made using EasyMP Network Projection a PowerPoint Slide Show cannot be started Was EasyMP Network Projection started while PowerPoint When connecting with EasyMP Network Projection make sure you close PowerPoint first Slide Show was running might not run if connecting while PowerPoint is running For Windows Troubleshooting When a connection has been made using EasyMP Network Projection the screen will not be refreshed when using an Office application Check Remedy Is the mouse moved continuously When you stop moving the mouse cursor the screen is updated If the screen does not update quickly stop moving the mouse cursor Error message when starting up EasyMP Network Projection Connection to the projector failed Try to connect again If it still does not connect check the network settings on the computer and the network settings for the projector For details on the network settings to be made on the projector see your projector User s Guide for details The keyword does not match Re enter the keyword Check the Projector
17. EXCEED YOUR VISION EasyMP Network Projection Operation Guide Contents Before Use Functions of EasyMP Network Projection ccccecceccece 5 Sharning the Projector 2 2c4 605s 06snd bbaeteseeiedasdenin es eeseroreeewtes 5 Various Screen Transfer Functions 0 cc ccc cece eect eee ee eens 5 Installing the Software cece cece ccc cc cc cccecccecececes 6 Software RequireMentS 0 0 ccc cece cece cece eee e eee e eee e eee eeeeeeeees 6 YSCANNG ach at nqcaa ne tice new EE ae esa ae 6 EasyMP Network Projection Summary TWO Connection MOdeS ccccccccccccccccscccccscccvcees 9 Advanced Connection Mode 00 c cece cece e cence ee eeeeeeeeeeee 9 Quick Connection Mode Only when the optional Wireless LAN unit Calas A ne eer ere ee er ere ee Ter Tere eer 9 Steps TOF CONNECUNG 60 i060verebs cache ecuk ee veseneuwdeacbien oueveentwes 10 Preparing to CONNEC sc 6 6 5 oscsseedon 0s 060604460005 0066008 05004 11 Connecting to a Projector on a Network and Projecting 12 Operating the Projector ccc cece tses torur EEEa EDENES 12 Operating the Computer cece cece e eee e eee eeeeeees 13 Using the Connection Screen cece eee eee eee eeeees 14 SING Ne LOOSE eraa war ee AE A SEREAS 16 Functions and Settings for EasyMP Network Projection Projecting Only a PowerPoint Slide Show Presentation Mode 20 Using Multi Screen Display cccccccc
18. Microsoft Windows XP Professional operating system Microsoft Windows XP Home Edition operating system Microsoft Windows Vista operating system Microsoft Windows 7 operating system In this guide the operating systems above are referred to as Windows 2000 Windows XP Windows Vista and Windows 7 Furthermore the collective term Windows may be used to refer to Windows 2000 Windows XP Windows Vista and Windows 7 and multiple versions of Windows may be referred to as for example Windows 2000 XP Vista with the Windows notation omitted Mac OS X 10 3 x Mac OS X 10 4 x Mac OS X 10 5 x Mac OS X 10 6 x In this guide the operating systems above are referred to as Mac OS X 10 3 9 Mac OS X 10 4 x Mac OS X 10 5 x and Mac OS X 10 6 x Furthermore the collective term Mac OS is used to refer to them Trademarks IBM DOS V and XGA are trademarks or registered trademarks of International Business Machines Corporation Macintosh Mac Mac OS and iMac are trademarks of Apple Inc Microsoft Windows Windows NT Windows Vista PowerPoint and Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Notices Other product names used herein are also for identification purposes only and may be trademarks of their respective owners Epson disclaims any and all rights in those marks Software Copyright This product uses free softw
19. O2FACT O GE Standby EMPO2FAC2 O GE Standby EMPO2FAC3 192 168 11 1 192 168 11 2 192 168 11 3 Save in the profile Clear list A q Set options p Troubleshooting Connect C Disable interrupt connection C Use multi display The Set options screen is displayed Set each of the items Confirm the details of the set items in the next step When you have made all the necessary settings click OK to close the Set options screen Setting Each Item Set each item from the General settings tab and the Adjust performance tab General settings tab Set options General settings Adjust performance Audio Output Use full screen video transfer L Encrypt communications Display Connection Mode Selection window on startup Search method on startup Automatic search on startup Specify search method after startup Search with the last network configuration Edit profile Switch LAN This setting is disabled because the projector does not support the movie sending function Use full screen video transfer Select to encrypt and transmit data Even if data is intercepted it cannot be decrypted Encrypt communications When using Quick Connection Mode make sure you always select this checkbox Select to encrypt and transmit data Even if data is intercepted it cannot be decrypted Using Set options Display Connec tion Mode Selection window on startup
20. a Different Subnet Making a Profile Profiles are made by saving search results For details on how to edit a previously saved Profile see the following section p 34 Procedure LC While the projector is displayed on the EasyMP Network Projection projector selection screen click Save in the profile si EasyMP Network Projection Ver X XX Advanced Connection rn A c e Automatic search 5 3 Manual search E Profile Auto ne a Ee Select a projector and connect it Status Projector name IP address O QL Standby EMPO2FACT 192 168 11 1 F G Standby EMPOZFAC2 192 168 11 2 C GD Standby EMPO2FAC3 192168113 CL Saveinthe profile JA Clearlist_ Sen C Disable interrupt connection C Use multi display Set options Troubleshooting Connect The Save in the profile screen is displayed Saye in the profile Enter the Profile Hame Profile name Untitled Add Cancel Projector information is registered in the Profile If you have previously saved a Profile you are prompted to confirm whether or not to overwrite To save a Profile with a different name select Save as If you have created a folder for a Profile the follow ing screens are displayed After entering the Profile name and se lecting the Save in destination click Add For Windows save in the profile a xj Enter the profile name and specify where to sawe the profile Profile name lu
21. are as well as software to which this company holds the rights 2010 Epson America Inc 10 11 CPD 28284
22. cal dots that is used by IBM PC AT compatible computers Notices Notices Copyright Notice All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Seiko Epson Corporation No patent liability is assumed with respect to the use of the information contained herein Neither is any liability assumed for damages resulting from the use of the information contained herein Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by the purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations to this product or excluding the U S failure to strictly comply with Seiko Epson Corporation s operating and maintenance instructions Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation This information is subject to change without notice Illustrations in this guide may differ from the actual projector About Notations Microsoft Windows 2000 operating system
23. ccecccecccccecs 21 Example of Adjusting the Virtual Display 0 cece cece ee ees 22 Procedure Before Using the Multi screen Display Function 23 Setting the Virtual Display 0 0 cc ccc cece eee eee eee eeeeeees 23 Enable the virtual display driver Windows only 0e eee eee 23 Adjusting the Virtual Display ccc cece cece eee eee eeeees 24 Allocating the Image to be Projected ccc cece cece eee eees 28 Projecting the Allocated Images cc ccc ccc ccc ect ee eenes 28 Connecting to a Projector on a Different Subnet 30 Specifying Either an IP Address or Projector Name and Performing a Search Advanced Connection Mode Only 0 ccc eee eee ees 30 Performing a Search with a Profile ccc ccc ccc e eee eee eeees 31 Making a Prole cs60i20uc042eerinceresacsuteew estes EEES Era 32 Searching by specifying a Profile 0 cece cece ee eee eeees 33 Managing a PIOMlCvs csunccduduccedneeyibenteeedd heat theese tases deines 34 USING Set ODLIONS a5 6 65406 iori rto ttn reunaa 36 SEUNG EACH IEW eer aE AEEA E EE seerrw ese eenteren cone 36 General settings tab 2 0 ccc ccc ccc cc cece eee e ee eeeees 36 Adjust performance AD insite en oun tens nwemncrvesceonns evane cea 37 Audio Output fa ach cucetnnceonss a24anetacanesecoueneuseeeetendese sue 38 Contents Appendix When a connection has been made using EasyMP Network Projec
24. ct your location Installing the Software Double click the EMP_NPInstaller mpkg icon in the EPSON AON For EMP NS Connection users 7 window The EMP NS Connection name has changed l Before change EMP NS Connection Installation starts After change EasyMP Network Projection Follow the on screen instructions to install When using the same function as EMP NS Connection on the projector Ai install EasyMP Network Projection after uninstalling EMP NS Connection QE Uninstalling You cannot connect to the projector correctly using EMP NS Connection For Windows Select Start Settings Control Panel Add Remove Programs or Add Procedure or Remove Programs and then remove EasyMP Network Projection For Mac OS For Windows E aS Double click EasyMP Network Projection Uninstaller app from the EasyMP Network Projection folder to uninstall Easy MP Network Projection Turn on your computer Insert the EPSON Projector Software CD ROM into the computer The installer starts automatically vl AON If the installer does not start automatically double click the CD ROM j drive from My Computer or Computer Follow the on screen instructions to install For Mac OS Y Ly X a E Turn on your computer ny Aw CTT lt Insert the EPSON Projector Software CD ROM into the computer EasyMP Network Projection Summary This chapter explains how to connect the computer and the projecto
25. d p 28 z Profile You can search for a projector on the network using a Profile saved using Save in the profile p 31 SSID Quick Connection Mode only The projector s SSID is displayed Connecting to a Projector on a Network and Projecting Signal intensity This is displayed when the connection is made in Quick Connection AL Mode As the Signal intensity increases so does the number of lit indicators Update list Quick Connection Mode only Updates Status and Signal intensity Using the Toolbar The toolbar is displayed on the computer screen after EasyMP Network Projection starts and a connection is made with the projector You can use this toolbar to operate and make settings for the projector Select target projector Click to limit the projectors operated from the toolbar when projecting from multiple projectors using the distribution function or Multi screen display The indication below the icon shows the projectors that can be controlled ALL indicates that all of the connected projectors can be controlled For example when 1 3 is displayed projectors No 1 and No 3 can be controlled EMPO2F AG 1 EMPO2F AG 1 EMPO2F AGS Select the projector to be controlled Indicates the No of an allocated projector This No indicates the No of the projector that you can control from the toolbar Indicates the status of the projector Stop Stops projecti
26. display Excel file Using Multi Screen Display Procedure Before Using the Multi screen Display Function 1 Setting the Virtual Display p 23 In a Windows environment enable the virtual display driver as necessary Also for both Windows and Mac OS set up the virtual display arrangement Allocating the image to be projected p 28 Open the file to be projected and then move the screen to the virtual display according to the actual projection arrangement Projecting the allocated images p 28 Allocate a virtual display number to a projector that is connected through the network and then start projection Setting the Virtual Display This chapter explains the virtual display for arrangement example 1 E p 22 Enable the virtual display driver Windows only Enable the virtual display driver Those users listed below do not have to perform this operation Go to procedure Adjusting the Virtual Display p 24 Those users who have enabled virtual displays installing EasyMP Network Projection For Mac OS users Procedure Start Windows on the computer and then select Start Programs or All Programs EPSON Projector EasyMP Network Projection Add Remove Virtual Display The Add Remove Virtual Display screen is displayed lt Select the virtual display you want to use Up to four monitors can be added In this example a single virtual display is to be used When se
27. e the conference room without With EasyMP Network Projection the connection with the computer that was previously connected cutting off the network connection can be cut off when another computer tries to connect with the projector and it connects with the computer that is trying to connect Therefore when a Projector Keyword is not set for the projector or if you know the Projector Keyword you can cut off the current connection and if you perform a connection operation you can connect to the projector When a Projector Keyword is set for the projector if you do not know the Projector Keyword restart the projector and reconnect The projector is not found when EasyMP Network Projection is started Check Remedy Is the Wireless LAN unit connected Check that the optional Wireless LAN unit is securely connected For Wireless LAN Troubleshooting Is the Network Configuration screen from the When the Network Configuration screen is displayed on the projector network connection for Configuration menu displayed on the projector EasyMP Network Projection is disabled Close network settings on the projector and return to the LAN standby screen Are the a s LAN card and the built in LAN function that LAN is valid a E a checking Control Panel System Hardware in the device manager and so a Is the SSID the same as that of the access point Set an SSID that is different from that of the access point See your projecto
28. ecting to the Wireless LAN manually computer starts up Quick Connection Mode Glossary Glossary This section briefly explains the difficult terms that are not explained in the text of this guide For details refer to other commercially available publications MAC Address An abbreviation of Media Access Control The MAC Address is an ID number unique to each network adapter A unique number is assigned to each network adapter and data is transmitted between network adapters based on this identification A type of video signal with a resolution of 640 horizontal x 480 vertical dots that is used by IBM PC AT compatible computers SVGA A type of video signal with a resolution of 800 horizontal x 600 vertical dots that is used by IBM PC AT compatible computers A type of video signal with a resolution of 1 024 horizontal x 768 vertical dots that is used by IBM PC AT compatible computers A type of video signal with a resolution of 1 600 horizontal x 1 200 vertical dots that is used by IBM PC AT compatible computers A method of Wireless LAN connection that communicates with wireless LAN clients without using an access point It is not possible to communicate with two or more devices simultaneously Virtual Display The screen for one computer is output to multiple displays A large virtual screen can be created by using multiple displays A type of video signal with a resolution of 1 280 horizontal x 1 024 verti
29. ection is enabled until the computer is restarted A Do you want to change the color scheme to improve performance Windows has detected your computer s performance is slow This could be because there are not enough resources to run the Windows Aero color scheme To improve performance try changing the color scheme to Windows Vista Basic Any change you make will be in effect until the next time you log on to Windows gt Change the color scheme to Windows Vista Basic Keep the current color scheme but ask me again if my computer continues to perform slowly gt Keep the current color scheme and don t show this message again How do I decide whether to change the color scheme to improve performance Limitations when projecting from Windows Media Center You cannot project images in full screen display using Windows Media Center Switch to the window display mode to project the images Troubleshooting Troubleshooting If any of the following problems occur refer to the pages given for each problem Problems concerning network functions Cannot connect to the projector p 43 When a connection is made using EasyMP Network Projection the projected image remains as it is and a connection cannot be made from another computer p 43 The projector is not found when EasyMP Network Projection is Started amp p 43 Cannot connect in Advanced Connection Mode or Wired LAN connection p 45 The Sl
30. egistered as an exception necessary settings to open the ports The ports used by EasyMP Network Projection are 3620 3621 and 3629 Is the network cable connected correctly Check that the network cable is connected correctly Reconnect it if it is not connected or not For Wired LAN connected properly Troubleshooting Cannot connect in Advanced Connection Mode or Wired LAN connection Is the SSID setting different Set the computer the access point and the projector to the same SSID See your projector User s Guide for details Is the same WEP key set When selecting WEP from Security set the access point the computer and the projector to the same WEP key See your projector User s Guide for details Are the connection denial functions such as MAC Address Set the projector to allow connections from the access point restrictions and port restrictions set correctly at the access point Are the IP address the Subnet Mask and the Gateway When not using a DHCP adjust each setting See your projector User s Guide for details Address for the access point and the projector set correctly Are the access point and the projector s subnet different Select Manual search from EasyMP Network Projection specify the IP address and connect p 30 The Slide Show cannot be displayed on the desired display when the multi screen display function is being executed Are you using PowerPoint 2002 or an earlier version To
31. his monitor 1 Plug and Play Monitor on NVIDIA GeForce 6200 TurboCachel T Mo Screen resolution Color quality for that screen cannot be projected Y Doo e Depending on the hardware the number of the secondary monitor may be ake ee other than 2 When the monitor icon is displayed on the screen click the Use thie device as the primar monitor F s Ie o a E E E E icon and confirm that the monitor type shown under Display is other than secondary Display i i QE e When an external monitor is connected as a secondary monitor the image 4 Using Multi Screen Display e For the Screen Resolution settings see the following p 40 When the monitor icon is arranged a virtual display is connected as the image like below j Click the OK button to close the Display Properties screen Up to this point the virtual display layout has been fixed Allocate the projecting images next p 28 wy Start EasyMP Network Projection Double click the Applications folder of the hard drive volume in which EasyMP Network Projection is installed and then double click the EasyMP Network Projection icon In this example we select and start in Advanced Connection Mode F Network Projection Ver x XxX Advanced L onnection wr 00 Manual search i Profile v i Automatic search Select a projector and connect it Status Projector name IP address o G Standby EPSON PJ 192 168 10
32. ide Show cannot be displayed on the desired display when the multi screen display function is being executed p 45 Applications are no longer displayed from the computer screen when the multi screen display function is executed p 45 The mouse cursor is not displayed on the computer screen p 46 When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear p 46 When a connection is made using EasyMP Network Projection a PowerPoint Slide Show cannot be started p 46 When a connection has been made using EasyMP Network Projection the screen will not be refreshed when using an Office application p 47 Error message when starting up EasyMP Network Projection p 47 Network settings are not restored after cutting the connection to the computer with EasyMP Network Projection p 48 Troubleshooting Problems Concerning Network Functions Cannot connect to the projector Check the message on the screen and then apply the following countermeasures The application version used is not supported Install the Install the current version of EasyMP Network Projection from the EPSON Projector Software CD ROM latest version of the application on your computer supplied with the projector When a connection is made using EasyMP Network Projection the projected image remains as it is and a connection cannot be made from another computer Did the presenter leav
33. layered window Version Performance adjustment slider Transfer layered window Restore Defaults The performance can be set to Fast Normal and Fine Set to Fast when movie projections are interrupted Windows only excluding Windows Vista and Windows 7 Set whether or not to transfer a layered window The layered window is in use when contents such as messages displayed on the computer are not projected by the projector Select this checkbox to project contents such as messages that use the layered window Clear this checkbox if you do not want the mouse pointer to flicker on the screen You can reset all adjustment values for Set options to their default settings However you can retain settings for Edit profile and Switch LAN in General settings Using Set options QE When you click Vd on the toolbar only the Adjust performance tab is displayed Audio Output tab Because this projector does not support the audio sending function settings on the Audio Output tab are disabled Appendix Connection Limitations Connection Limitations Display Color When projecting computer images while running EasyMP Network Projection the following restrictions apply Confirm these points E oh colors E T E couse A projected Supported Resolutions 16 bit color About 32 000 colors 16 bit 32 bit color About 16 7 million colors 32 bit The following computer screen resolution
34. less LAN system for the computer and each projector must be the same You can modify the SSID and Wireless LAN system for the projector from the Network menu in the projector s Configuration menu See your projector User s Guide for details Troubleshooting Display layout Procedure For Windows Display properties G Select Start Programs or All Programs EPSON Projector EasyMP Network Projection EasyMP Network Projection V2 XX to start EasyMP Network Display layout and Display properties are added at the bottom of Projection the screen Using Multi Screen Display Click Display properties Drag the displayed monitor icon and place it where desired Here the actual monitor 1 is placed on the left while the virtual monitor 3 is placed on the right C Disable interrupt connection Use mult display When the computer has multiple display output terminals the numbers assigned to the virtual terminals will be sequential to is wok those of the physical terminals Display Properties n al Display properties The Display Properties screen is displayed Click the Settings tab Display 1 Plug and Play Monitor on WYIDILA GeForce 6200 TurboCache ThM Screen resolulion Color quality Less YJ More Highest 32 bit w 1280 by 1024 pixels E EE EE E Use this device as the primary monitor Extend my Windows desktop onto t
35. n the connection is complete the computer screen is project ed The following EasyMP Network Projection toolbar is displayed on the computer screen You can use this toolbar to operate the projector and make settings and to disconnect the network con nection For details on the toolbar see Using the Toolbar E p 16 peeves or at Ul mn ill Ree Serpe ered may lene saree een Cerra eae ee M CAMT MEADE FPOPECIOR Y ET A z ALL Ta a a ah E Zz When connecting from another computer such as when changing presenters start EasyMP Network Projection from the computer you want to connect The computer that is currently connected is disconnected and the projector is then connected with the computer that is trying to connect now If a connection is made while Disable interrupt connection is set the connection is not switched to another computer Connecting to a Projector on a Network and Projecting Using the Connection Screen Start EasyMP Network Projection to display the following screen The operation of each button or item is described in the following table When the system starts in Advanced Connection Mode Status Projector name SSID Standby EMPOZFACI EPSONI O GD Standby EMPO2FAC2 EPSON2 Projector name IP address EMPO2FAC1 192 168 11 1 C Disable interrupt connection EMPO2FAC2 192 16
36. om different computers during a meeting or presentation you can progress smoothly without changing the signal cable between each computer Even a distance between the projector and the computer does not cause any problems Various Screen Transfer Functions You can use the following screen transfer functions e Multi screen display p 21 You can project different images from up to four projectors from one computer allowing you to project landscape images such as spreadsheets and so on as one continuous image e Presentation Mode p 20 This function can project a PowerPoint Slide Show running on a computer You can give stylish presentations by projecting a black screen while making preparations and so on and when not performing a Slide Show e Distribution function The screen being displayed by a remote computer can be simultaneously displayed by up to four projectors on the same network e Switching function By using the meeting switching function if Easy MP Network Projection is installed on all of the computers the presenters can take turns and project their own images without changing cables Installing the Software Installing the Software You can find EasyMP Network Projection on the EPSON Projector Software CD ROM Install the software on the computer you are using Software Requirements EasyMP Network Projection runs on computers that meet the following requirements OS Window
37. on while connected to the projector A black screen is projected while stopped Audio does not stop To stop the audio or to display a User s Logo while projection is stopped use the A V Mute function Show Releases Stop or Pause Connecting to a Projector on a Network and Projecting Pause Projector control Pauses projected images while connecting to the projector While the projector is connected to the network the The audio is not paused projector s A V Mute Switch PC source and Switch video source functions can be controlled from both the Remote Control and the projector s Control panel Presentation Mode Each time this is clicked Presentation Mode switches between enabled disabled p 20 Click to display the following toolbar Projector control 4 A V Mute A V Mute The same function as the A V Mute button on the remote control Switch PC source a Switch PC source The Source alternates between Computer Computer2 USB Display USB and LAN each time you click Switch video source E Switch video source The Source alternates between S Video and Video each time you click S Video does not switch if the cable is not connected Connecting to a Projector on a Network and Projecting Screen Preview g Switch toolbar display The toolbar display is switched as follows The toolbar display remains as is until switched again Displays the multi screen preview sc
38. or Profile Not found Displayed when a projector cannot be amp found as a result of Manual search or Profile In Quick Connection Mode you can only select multiple projectors with the same SSID Displayed when a projector cannot be found as a result of Manual search or Profile Projector name The projector s name is displayed Disable interrupt connection Check the box to prevent an interrupt connection by other computers while connected to the selected projector Use multi display Check the box to use the Multi screen display function When this is selected Display layout and Display properties are displayed at the bottom of the screen p 21 Troubleshooting If there is a problem and you cannot have a connection press this button to open the EasyMP Network Projection Troubleshooting screen Connect Connect to the projector you selected from the search results list When a connection is made with a projector a toolbar is displayed Set options You can make general setting options such as the processing method when starting up EasyMP Network Projection For details see Set options p 36 Save in the profile Saves the results of a network projector search as a Profile p 31 Clear list Deletes all search results IP address Advanced Connection Mode only IP address The projector s IP address is displayed Display Select the number displayed when Use multi display is selecte
39. r User s Guide for details a wien re Is the DHCP function for Wired LAN turned On Set the DHCP setting to Off from Wired LAN in the Configuration Menu See your projector User s Was the network adapter used selected correctly with If the computer has multiple LAN environments it cannot connect unless the network adapter is EasyMP Network Projection selected correctly When using a computer running Windows start EasyMP Network Projection and select the network adapter you are using from Set options Switch LAN p 36 For Wireless LAN connection is the Wireless LAN setting Enable the Wireless LAN enabled when the computer is in power save mode Are there any obstacles between the access point and the Sometimes the electromagnetic wave situation prevents the projector from being found in a search computer or projector Check for any obstacles between the access point and the computer or projector and change their For Wireless LAN position to improve the electromagnetic wave situation Is the computer s Wireless LAN electromagnetic wave set Set the electromagnetic wave strength to maximum to low Does the Wireless LAN conform to 802 11g 802 11b or Itis only compatible with standards 802 11g 802 11b and 802 1 1a and not with other standards such 802 11a as 802 11 Is the firewall turned off or has the firewall been When you do not wish to turn off the firewall or register the firewall as an exception make the r
40. r via a network and the procedure for projecting images from your computer s screen with the projector Two Connection Modes Two Connection Modes There are two methods of connecting a computer and the projector via a Quick Connection Mode Only when the optional network by using EasyMP Network Projection Wireless LAN unit is installed Quick Connection Mode is only available when you install the optional Wireless LAN unit in the projector Quick Connection Mode temporarily assigns the projector s SSID to a computer creating an ad hoc connection and restores the computer s network settings after disconnecting p 11 Advanced Connection Mode Advanced Connection Mode is an infrastructure connection and connects to an existing network system via a network cable When connecting to a network via Wired LAN connect the projector to the network hub with a commercially available LAN cable If you install the optional Wireless LAN unit in the projector you can connect to the network via a wireless LAN access point e You can easily connect to a computer and project images from the computer without making network settings e This lets you connect easily without a connector cable and you can even connect if the projector and the computer are at remote locations Two Connection Modes A You need to perform steps 1 to 4 only the first time you connect Steps for Connecting P p y y 1 Install EasyMP Network Projec
41. re If necessary select another projector to be controlled p 16 Ky wu K a A l A _ 3 I ick the utton on the toolbar GY ws Uy ww CTT Presentation Mode begins 2 In Presentation Mode click the button again to exit Presentation Mode Using Multi Screen Display Using Multi Screen Display Multi screen display mode allows you to project different images from multiple projectors that are connected to a single computer With Windows multiple virtual display drivers can be set in the computer and each image can be projected by the projector Furthermore this function cannot be used in Windows Vista and Windows 7 because it is not compatible For Mac OS an external monitor needs to be connected to the computer to enable this function While the following explanation refers to virtual display for Mac OS the operation relates to the screens displayed on the physically connected monitor
42. reen Click a to display a preview with the settings you have made Click each display to enlarge each Screen Preview to Full full screen EaspMF Network Projection Wer Hrs ae Domea nee Mormal Full Set options Transmission performance during the transfer of computer images can be adjusted p 36 EaswMP Network E E Disconnect Movie Sending Mode Not enabled on this projector The message The connected projectors do not support Movie Sending is displayed Disconnect Disconnect Disconnects the connection to the projector Signal intensity ms This is displayed when the connection is made in Quick Connection Mode As the Signal intensity increases so does the number of lit indicators Functions and Settings for EasyMP Network Projection This chapter explains the functions that may be useful in a meeting or presentation such as the Multi Screen Display which allows you to send images to multiple projectors from a single computer Projecting Only a PowerPoint Slide Show Presentation Mode Projecting Only a PowerPoint Slide Show Presentation Mode In Presentation Mode the images are only displayed when performing a PowerPoint Slide Show on a computer When you stop Slide Show the projector displays a black screen This is useful when you only want to display the Slide Show In addition to PowerPoint Keynote is compatible with Presentation Mode for Mac OS Procedu
43. rititle Save in E 0 Profile ef building A eof building B Cancel Connecting to a Projector on a Different Subnet For Mac OS Procedure Save in the profile Click Profile on the EasyMP Network Projection projector selection screen Enter the profile name and specify where to save the profile If no Profile is registered you cannot select Profile r Profile name Untitled 3 Save i Building A l F Building B ae Automatic search 2 3 Manual search Select a projector and connect it Status Projector name IP address Nee O QL Standby EMPO2FACI 192 168 11 1 QE For details on how to create a folder for a Profile see the following og aa a G E tandby 168 11 section p 34 O G Standby EMPO2FAC3 192168113 Searching by specifying a Profile l C Disable interrupt connection C Use multi display Set options You can search by specifying the Profile you created Troubleshooting Connect YK From the menu that is displayed select the projector you want to connect to A EasyMP Network Projection Ver X XX Advanced Connection oe Automatic search 7 ae Manual search Profile Select a projector and connect it Building 4 gt R Status Projector name Building B gt Building B 1st floor Building B 2nd Floor QE Standby EMPO2FACT 192 168 1141 The search results are displayed
44. s 2000 Service Pack 4 The following 32 bit OS versions Windows XP Windows XP Service Pack 1 or later Windows Vista Windows Vista Service Pack 1 or later Windows 7 The following 64 bit OS versions Windows 7 Mac OS X 10 3 x Mac OS X 10 4 x Mac OS X 10 5 1 or later Mac OS X 10 6 x Recommended Mac OS X 10 3 9 10 4 11 10 5 8 CPU Mobile Pentium III 1 2GHz or faster Power PC G3 900MHz or faster Recommended Pentium M 1 6GHz or faster CoreDuo 1 83GHz or faster Amount of Memory 256MB or more ee pmconmece stern Hard Disk 20MB or more tor nail Display Resolution of no less than XGA 1024x768 and no higher than UXGA 1600x1200 Display color of 16 bit color or greater approx 32000 display colors Operation is not guaranteed in Mac OS X 10 5 0 because the Firewall settings are not set correctly when the version is updated Installing Make sure you check the following points before starting installation e When using a computer running any of the following operating systems you must have administrator authority to install EasyMP Network Projection e Windows 2000 e Windows Vista e Windows XP e Windows 7 e Make sure that you close all running applications before starting installation e When the language selected for the installation varies from that of the OS being used the screens may not be displayed correctly e To download the latest version of EasyMP Network Projection go to www epson com and sele
45. s can be projected You cannot connect to a computer with a resolution greater than UXGA The operational guarantee for multi screen display is 16 bit and 32 bit e VGA 640x480 color e SVGA 800x600 e XGA 1024x768 e SXGA 1280x960 Number of Connections e SXGA 1280x1024 You can connect up to four projectors to one computer and project e SXGA 1400x1050 simultaneously e WXGA 1280x768 You cannot connect multiple computers to one projector e WXGA 1280x800 simultaneously e WXGA 1440x900 e UXGA 1600x1200 Others Supported resolutions when multi screen display function is on e If the transmission speed of the Wireless LAN is low the network When using a computer screen with a unique aspect ratio depending on 5 P d p p 4 might be cut off unexpectedly the resolution of the computer and the projector the resolution is increased or decreased so as not to impair the image quality e Audio is not transmitted Depending on the resolution at times the vertical or horizontal margins e When videos are played back they do not play back as smoothly as may be projected in black when displayed on the computer e Applications that use part of DirectX functions may not be displayed correctly Windows only e Cannot project full screen MS DOS prompts Windows only Connection Limitations e There are times when the image on the computer screen and the image projected by the projector may not match exactl
46. s on the computer and the network settings on the projector For details on the network settings to be made on the projector see your projector User s Guide for details One or more connected projectors do not support There is a projector with an incompatible resolution in the connection destination Change the resolutions greater than SXGA Reduce the screen computer screen resolution to SXGA 1280x1024 or less resolution and reconnect One or more projectors are not responding You cannot connect to multiple projectors simultaneously Check the network settings on the computer and the network settings on the projector For details on the network settings to be made on the projector see your projector User s Guide for details Enter the keyword displayed on the projector screen Check the Projector Keyword displayed on the LAN standby screen and enter the Projector Keyword Cannot start this application while USB Display is running Close USB Display and then start EasyMP Network Projection Cannot connect to the projector using this version of Install the current version of EasyMP Network Projection from the EPSON Projector Software CD ROM EasyMP Network Connection Install the latest version of supplied with the projector EasyMP Network Projection Network settings are not restored after cutting the connection to the computer with EasyMP Network Projection Are you manually connecting to a Wireless LAN when the Try conn
47. tion that Profile whenever you subsequently want to search for a projector 1 Ae m o 2 Automatic search Manual search Profile Au HUDI l on a different subnet p 31 pe Select a projector and connect it aa Ise Status Projector nam IP address AON e If a search fails to find a projector the most likely causes are as follows Proceed as appropriate depending on the cause of the failure For both Windows and Mac OS If there is no wireless LAN signal or if the signal is weak check whether there is anything that could be interfering with the signal A 5 a ee ave in the profile ear lis When the optional Wireless LAN unit is installed in the projector and ___Saveinthe profile ___Clearlist_ O Qa Standby EMPO2FACI 192 168 11 1 O Ga Standby EMPO2FAC2 192 168 11 2 O GD Standby EMPO2FAC3 192 168 11 3 C Disable interrupt connection C Use multi display access point has been selected troubleshooting connecting Mac OS to a wireless LAN Check whether AirPort is set to On Or check whether an appropriate Connecting to a Projector on a Different Subnet Enter the IP address or the projector name for the projector You can save a search for a frequently used projector as a Profile A you want to connect to and click OK Profile is a file containing all of the information for a projector such as the projector name and IP address If you specify that information from
48. tion the screen will not be refreshed when using an ee EE 40 Office application A A ae 47 z Inco Error message when starting up EasyMP Network Projection 47 Bppots CSO TON 24 che ceteris aeace aroun EA NEEE 40 Network settings are not restored after cutting the connection to the Display COV ON gate crete seer etn bie ee oh nase oh en oe ea en Gee eed ee eh eee 40 computer with EasyMP Network Projection OE S 48 Number Of CONNCCUONS vscseccesndewdeieviedaewndatdeiowerbesiedenanens 40 TAGS ao deen oe P bak boa hed oe ede ees eae 40 Glossary eseseeseseeeerereerereerereerereerereerereereree 49 When Using Windows Vista or Windows 7 ssussssssssesssrerererss 41 Noces eaea E TE 50 Aranos wnan projecting from Windows Photo Gallery Copyright Notice ccc cece eee cece e eee e nent eee eeeeeeeees 50 ANAON n WINONG mero neteees eee eae AOUT NOtAUONS cccvtornertaweneuwerees ane cmenwe Hoan teeen blade aes 50 Limitations when projecting from Windows Media Center TRAGIOIWIGIEK 5c cea EE EE E neuen SEEE 50 TYOUDICSNOOUNG 65 065460esba0ederebo at cnaneieaenhadees eee 42 Problems Concerning Network FUNCTIONS 0 cc cece eee eee eens 43 Cannot connect to the projectOr cece cc cece cece eee eeeeenes 43 When a connection is made using EasyMP Network Projection the projected image remains as it is and a connection cannot be made from another computer ccc ccc ccc cece
49. tion on the computer to be connected Use the following steps to connect the computer to the projector and p 6 project in EasyMP Network Projection To connect the computer and the projector via a network with EasyMP Network Projection connect in Advanced Connection Mode Advanced 2 Make network settings on the computer and put it into network Connection Mode is an infrastructure connection and connects to an connection status p 11 existing network system via a network cable When connecting to a network connect the projector to the network hub with a commercially available LAN cable 3 For Quick Connection Mode Install the optional Wireless LAN unit in the projector if already installed go to step 5 For Advanced Connection Mode Enable the Wired LAN or Wireless LAN adapter in Port Configurations Computer s documentation t 4 Make network settings on the projector and put it into network connection status See your projector User s Guide for details v 5 Start EasyMP Network Projection on the computer and connect with the projector p 12 When the computer you are using is normally connected to the network you do not need to make network settings on the computer Preparing to Connect Preparing to Connect Use the following procedure to set up the computer for connection For Windows Make network settings for the computer by using the utility software supplied with the LAN adapter For
50. tting multiple virtual displays select as many displays as is necessary Any one of the displays can be selected ANU aaa Y g 9 a Cli Y Clic N 7 Add Remove irtual Display E x Select the virtual display to use If you want to select a virtual display other than the one currently in use you Will need to restart your computer V virtual Display 1 I Virtual Display 2 I Virtual Display 3 Virtual Display 4 eS When you click OK the drivers for the virtual display are enabled At this point it is normal for the display to flicker Wait for the Add Remove Virtual Display screen to close Using Multi Screen Display Adjusting the Virtual Display lt Select the Use multi display checkbox After starting EasyMP Network Projection the procedure for setting up _ HELA OBS sea Be OS rade nd ella Ta a the virtual displays differs for Windows and Mac OS The procedures are 2 Automatic search J Manual search Profile explained separately below ne E Select a projector and connect it Kis Status Projector name IP address Display Q Check the following points before starting EasyMP Network Projection GB Sindy EMPO2FACI 19216811 NE when connecting via Wireless LAN If the following points are not set QE Sandy EMPO2FAC2 192 168 11 2 correctly Multi screen display cannot be used e The SSID for the computer and each projector must be the same e The wire
51. y When Using Windows Vista or Windows 7 Note the following points when using EasyMP Network Projection on a computer running Windows Vista or Windows 7 Limitations when projecting from Windows Photo Gallery Note the following two limitations when launching Windows Photo Gallery when EasyMP Network Projection is running e Slide Show is played back in simple mode when projecting from Windows Photo Gallery Because the toolbar is not displayed you cannot make changes while playing a Theme effects regardless of the Windows Experience Index rating Once simple mode has started you cannot change modes while Windows Photo Gallery is running even if you close EasyMP Network Projection Restart Windows Photo Gallery e You cannot play movies Limitations in Windows Aero Note the following two limitations when the window design for your computer is Windows Aero e The layered window is projected regardless of Transfer layered window from Set options in EasyMP Network Projection For example when Transfer layered window for EasyMP Network Projection toolbar is disabled it is not projected even if it is displayed on the computer screen however the toolbar is projected e A few minutes after you connect a computer to the projector over a network with EasyMP Network Projection the following message is displayed It is recommended that you select Keep the current color scheme and don t show this message again This sel
Download Pdf Manuals
Related Search