Home

Emerson Process Management Wireless Gateway 1420 User's Manual

image

Contents

1. amp M Modbus pco lg Trends 5 Select method and click Submit Quick Installation Guide 00825 0100 4420 Rev CA 1420 Wireless Gateway June 2007 STEP 3 BASIC ETHERNET OR SERIAL CONFIGURATION To configure the 1420 for an Ethernet Network Table 2 Ethernet Communication Settings on page 15 is available to assist in recording the necessary information 1 Determine 1420 Ethernet Port for connecting to Ethernet Network If using a wired connection use Port 1 P1 IT Process Control Network Administrator or Technician can provide the following a 1420 fixed IP Address or DHCP Host Name b Netmask Subnet Mask c Gateway BEST PRACTICE Keep these values in a secure location not accessible by unauthorized personnel 2 Configure 1420 Ethernet IP settings a Access the 1420 with Administrator access b Navigate to Setup gt Internet Protocol Address n 1420 m Ll aude Wireless Gateway E 192 168 1 10 E Cg Diagnostics 98 Monitor Zi E Explorer B Setup 3 Network 2 8 Internet protocol C Backup 5 Address EXSY Security User Accounts 3 Certificates Primary Interface 9 Obtain an IP address from a DHCP server M Obtain Domain Name from DHCP server Specify an IP address Access List Hostname 3 Protocols Domain Name A Time IP Address Eg Page Options 3 Restart Apps Gateway BOA HART B M Modbus c Enter configuration information determin
2. ener Value Reported for 32767 Any Integer rror 1420 Wireless Gateway 16 Quick Installation Guide 00825 0100 4420 Rev CA June 2007
3. best practice is to run the Serial or primary Ethernet cable P1 directly to the Information System Use conduit and or strain relief as necessary BEST PRACTICE When installing cable conduit run an ethernet connection from 1420 port P2 to a convenient y location indoors if the 1420 was ordered with m Output Code 2 This will simplify future configuration changes Y 10 Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway STEP 4 CONTINUED Connect to Information System 1 Wire the 1420 Primary Ethernet output or Serial Output connection to the Host System Ethernet or Serial input connections 2 For Serial connections connect A to A B to B and make sure all terminations are clean and secured to avoid wiring connection problems Figure 1 1420 Terminal Block Diagram 24V DC Serial r Power Input 1 r Modbus 4 Not Used Covered Secondary Primary BEST PRACTICE Typically twisted shielded pair cable is used to wire the Serial connection Standard practice is to ground the shield on the Serial Host side and leave the shield floating on the 1420 side Be sure to insulate the 1420 shield to avoid grounding issues NOTE In most systems A Tx and B Rx In some systems this is reversed For 4 wire systems see Figure 2 Figure 2 Typical
4. Full Duplex 4 wire to Half Duplex 2 wire Conversion Diagram Tx Rx Tx Rx Confirm wiring configuration with host system documentation Supply Power After mounting is complete supply power to the 1420 according to the following steps 1 Ground the 1420 using suitable grounding methods There is a case ground lug located near the terminal block and an external ground lug located near the conduit entries on the bottom of the housing 2 Connect the 24 V DC power wiring to the Power Input terminals in the 1420 The 1420 requires 500 mA of current see Terminal and Integration Diagram on page 14 3 Close the terminal cover and tighten securely BEST PRACTICE Use an uninterruptible power supply UPS to ensure that the network is still functional should there be a loss of power 11 Quick Installation Guide 00825 0100 4420 Rev CA 1420 Wireless Gateway June 2007 PRODUCT CERTIFICATIONS Approved Manufacturing Locations Rosemount Inc Chanhassen Minnesota USA Telecommunication Compliance All wireless devices require certification to ensure that they adhere to regulations regarding the use of the RF spectrum Nearly every country requires this type of product certification Emerson is working with governmental agencies around the world to supply fully compliant products and remove the risk of violating country directives or laws governing wireless device usage To see which countries our devices have received certi
5. L Kewnd L snqpow jeuas L 3ndu 1 3M0d 3aAvc Asepuodes poJ9 05 14 Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway Table 1 Ethernet Port Locations Settings Location 1420 Ethernet Port P1 Information System Switch or Access Point Switch or Access Point Ethernet Port Table 2 Ethernet Communication Settings Options Use Fixed IP or DHCP Fixed or DHCP Fixed IP Address or DHCP XXX XXX XXX XXX or Host Name XXXXXXX Netmask Subnet Mask YYY YYY YYY YYY Gateway ZZZLZZZLZZZLZZZ Table 3 Serial Connectivity Locations un RR DET Serial Card ID Serial Card Termination A Tx Serial Card Termination B Rx Table 4 Serial Communication Settings Setting Value Options on 1420 Default in Bold Modbus Slave Address 24 Baud Rate 9600 19200 38400 57600 Parity None Even Odd Sots i 4 4 x 2 Response Delay Time 0 ms Configurable in ms Unmapped Register Read Zero Illegal Data Response Unmapped Register Write OK Illegal Data Address Response Write Behavior Synchronous Queued Most Current Floating Point Representation Float Round Integer Scale Use Swapped Floating Pont vesNo Format Incorporate Values NvesNo Associated Status as Error Value Reported for Error NaN nf If Oter
6. found at http java com 2 Under Network Connections a Select Local Area Connection b Right click to select Properties Network Connections Gale Joe File Edit View Favorites Tools Advanced Help a Q Back i P search Folders C Address S Network Connections MD Status Other Places Y Repair Bridge Connections Details Y Create Shortcut Rename a Notepad Set Program Access and Defaults e vx Calculator it Programs gt Documents gt c L 2 Id o A Network Connections Ba Search 2 9 Printers and Faxes Ed Heb and Support Gl Taskbar and Start Menu 4 Hu E 9 Shut Down SUIS 1420 Wireless Gateway Quick Installation Guide 00825 0100 4420 Rev CA June 2007 c Select Internet Protocol TCP IP then click the Properties button d Select the Use the following IP address button and set the IP address to 192 168 1 12 e Set the Subnet Mask to 255 255 255 0 m Protocol TCP IP Properties L Local Area Connection Properties General Authentication Advanced Connect using E9 Broadcom NetXtreme 57xx Gigabit C This connection uses the following items M lel Client for Microsoft Networks vi 8 File and Printer Sharing for Microsoft Networks mi Sched LM Internet Protocol TCP IP Install Properties gt Description Transmission
7. 00 4420 Rev CA 1420 Wireless Gateway June 2007 c Click Yes to proceed through the Security Alert Security Alert x changed by others However there is a problem with the site s 5 Information you exchange with this site cannot be viewed or security certificate amp The security certificate was issued by a company you have not chosen to trust View the certificate to determine whether you want to trust the certifying authority o The security certificate date is valid The security certificate has a valid name matching the name of the page you are trying to view Do you want to proceed 1 View Certificate The 1420 Home Page will appear as shown below 1 192 168 1 10 1420 HG Home Page Microsoft Internet Explorer provided by Rotemount lnc 3 mmm Fie Edt View Faves Toots Hep 2 Om O msc rats O E hetps 192 168 1 10 Jserviet home DID amp 1420 M Wireless Gateway 192 168 1 10 So Diagnostics monitor o TA Explorer 2B Setup Diagnostics View status of modbus communications the chent server parameters and much more Monitor View data from each of the field devices Explorer View HART devices parameters and values Setup Configure the 1420 for operation configure field devices configure Modbus commurcations and register mapping Help Obtain help for installation setup various frequently asked questions term definitions and a site map to vie
8. Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks K K Show icon in notification area when connected Notify me when this connection has limited or no connectivity K amp General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 12 192 168 1 Subnet mask 255 255 255 0 Default gateway Use the following DNS server addresses Preferred DNS server I Alternate DNS server C f Select OK for each of the settings windows that have opened 3 Using the supplied crossover Ethernet cable attach your PC laptop to the 1420 s P1 Ethernet Receptacle far right Ethernet receptacle PC Laptop O 5 f P1 Ethernet Receptacle WARNING Do not connect to the P3 Power Over Ethernet POE port This port supplies power and could potentially damage the PC laptop Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway 4 Open a standard web browser Inter
9. Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway 1420 Wireless Gateway Start Step 1 Initial Connection for Configuration Step 2 Basic Security and Time Configuration Step 3 Basic Ethernet or Serial Configuration Step 4 Mount and Connect the 1420 EMERSON Process Management Quick Installation Guide 00825 0100 4420 Rev CA 1420 Wireless Gateway June 2007 2007 Rosemount Inc All rights reserved All marks property of owner Emerson Process Management Rosemount Temperature GmbH Emerson Process Management Rosemount Division Frankenstrasse 21 Asia Pacific Private Limited 8200 Market Boulevard 63791 Karlstein 1 Pandan Crescent Chanhassen MN USA 55317 Germany Singapore 128461 T US 800 999 9307 T 49 6188 992 0 T 65 6777 8211 T Intnl 952 906 8888 F 49 6188 992 112 F 65 6777 0947 65 6777 0743 F 952 949 7001 Enquiries AP EmersonProcess com A IMPORTANT NOTICE This installation guide provides basic guidelines for the 1420 Wireless Gateway It does not provide instructions for detailed configuration diagnostics maintenance service troubleshooting or installations Refer to the 1420 Wireless Gateway reference manual document number 00809 0100 4420 for more instruction The manual and this QIG are also available electronically on www rosemount com A WARNING Explosions could result in death or serious injury Installation of this device in an explosive en
10. ed above 3 To complete configuration without a firewall click Submit and proceed with 1420 Restart when prompted Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway STEP 3 CONTINUED To configure the 1420 for a Serial connection Table 4 Serial Communication Settings on page 15 is available to assist in recording the necessary information 1 Configure 1420 Serial Communication Settings a Access the 1420 Web Interface with Administrator access b Navigate to Setup gt Modbus gt Communication c Click Enable Modbus amp 1420 EMERSON Wireless Gateway 398 B swtesti420 8 qr Diagnostics C Enable Modbus 88 Monitor 8 GR Explorer Modbus TCP Port 502 Em S t Modbus Slave Address 1 247 9 A T Baud Rate 19200 M Bu ee Sup Network Parity o B Sainternet protocol None Even Odd Security Stop Bits 1_ Os B Time Response delay time ms 0 4 Unmapped register read response G Zero fill Otllegal data addr na System Backup Unmapped register write response ok Olllegal data addr 1 Page Options Write behavior synchronous Queued O Most Current Restart Apps BAA HART Floating point representation Float ORound Oscale EB M Modbus Use swapped floating point format Oves no gycommunication fpes REST wae sistat Oves Ov E Value reported for error floating point GNaN O tnf O Inf Oother ze E le Trends 32787 Value reported for error rounded and na
11. fication for use in see www rosemount com smartwireless European Union Directive Information The EC declaration of conformity for all applicable European directives for this product can be found on the Rosemount website at www rosemount com A hard copy may be obtained by contacting your local sales representative ATEX Directive 94 9 EC Emerson Process Management complies with the ATEX Directive Electro Magnetic Compatibility EMC 2004 108 EC EN 61326 1 1997 with amendments A1 A2 and A3 Industrial Radio and Telecommunications Terminal Equipment Directive R amp TTE 1999 S EC Emerson Process Management complies with the R amp TTE Directive FM Ordinary Locations Approval The 1420 Wireless Gateway has been evaluated and approved by FM for ordinary locations CE EMC Marking Compliance with European Union EMC Hazardous Location Certifications North American Certifications N5 FM Division 2 Certificate Number See Certificate Nonincendive for Class Division 2 Groups A B C and D Dust Ignitionproof for Class II III Division 1 Groups E F and G Indoor outdoor locations NEMA Type 4X Temperature Code T4 40 C T4 60 C 12 Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway Canadian Standards Association CSA N6 CSA Division 2 amp Dust Ignitionproof Certificate Number See Certificate Suitable for Class Division 2 Groups A B C D Dust Ignitionproof for Class Il Gro
12. net Explorer Mozilla Firefox or similar 5 Uncheck proxies Tools gt Internet Options gt Connections gt LAN Settings Internet Options JEI Ceai Area Network LAN Settings x General Security Privacy Conte t Connections Pjograms Advanced j 7 Automatic configuration 93 ies up an Internet connection click Automatic configuration may override manual settings To ensure the z un of manual settings disable automatic configuration Dial up and Virtual Private Network settings Komatically detect settings Add se automatic configuration script Choose Settings if you need to configure a proxy server For a connection j Proxy server o Use a proxy server for your LAN These settings will not apply to dial up or VPN connections Local Area Network LAN settings LAN Settings do not apply to dial up connections Qn seas Choose Settings above For dial up settings Lok cancel 6 Access the 1420 s default web page at https 192 168 1 10 Emerson Process Management Rosemount Division File Edit View Favorites Tools Help Oax O WA Favorites 4 b Address hitpsij 192 168 1 10 a Log on as User admin b Password default Connect to 192 168 1 10 1420 Restricted Access User name admin Password eccccce C Remember my password Quick Installation Guide 00825 01
13. tive integer Scaled floating point maximum integer value Use global scale gain and offset Yes Na Global scale gain Global scale offset d Configure the 1420 Modbus Communication settings to match the Host Modbus settings NOTE Modbus communications will fail if they are not configured identically on the Host and the 1420 e Click Submit and proceed with restart 2 When configuration is completed disconnect the PC laptop from the 1420 and return the PC laptop to its previous network settings Quick Installation Guide 00825 0100 4420 Rev CA 1420 Wireless Gateway June 2007 STEP 4 MOUNT AND CONNECT THE 1420 Integral Antenna with the 1420 on a Mast The optimal installation of the 1420 Wireless Gateway is on a pole approximately 1 8 meters above the top of the exterior wall of a building The following hardware and tools are needed Pipe mount with holes spaced 3 06 inches 78 mm apart horizontally and 11 15 inches 283 mm apart vertically Two 3 06 inch 78 mm by 5 16 inch U bolts 1 2 inch wrench 18m 6ft Mount the gateway by doing the following Strain 1 Insert one U bolt around the pipe and through the Relief top mounting holes of the pipe mount and the 1420 and another U bolt through the bottom mounting holes of the pipe mount and the 1420 2 Usinga 1 2 inch socket head wrench fasten the nuts to the U bolts and tighten BEST PRACTICE When mounting outside
14. ups E F and G Suitable for Class Ill Hazardous Locations Install per Rosemount drawing 01420 1011 Temperature Code T4 40 C T4 lt 60 C CSA Enclosure Type 4XEuropean Certification European Certification N1 CENELEC Type n ATEX See note below Certificate Number See Certificate ATEX Marking Ex Il 3 G EEx nA nL IIC TA 40 C T 60 C ND ATEX Dust Ignition proof Approval Certificate Number See Certificate Ex tD A22 IP66 T135 40 C lt Ta 60 EEx nA nL IIC T4 40 C lt T lt 60 C II3D Vmax 28V IECEx Certification N7 IECEx Typen See note below Certificate Number See Certificate Ex nC IIC T4 40 C lt T lt 60 C Rated Voltage 28V NF IECEx Dust Ignition proof Approval Certificate Number See Certificate Ex tD A22 IP66 T135 40 C lt T lt 60 C Vmax 28V CONDITIONS OF INSTALLING N1 AND N7 The Apparatus is not capable of withstanding the 500V insulation test required by Clause 9 4 of EN 60079 15 2005 This must be taken into account when installing the apparatus 13 June 2007 Quick Installation Guide 00825 0100 4420 Rev CA 1420 Wireless Gateway Figure 3 Terminal and Integration Diagram r P sn 10N pesnion L pasnion L pasni0n D1d s3a ynduy jeuas quawin gt op jenuew Aemared ssa JIM OZY L aypaas suondo fyAn euuo 30d pue zd 104
15. vironment must be in accordance with the appropriate local national and international standards codes and practices Please review the Hazardous Locations Certifications for any restrictions associated with a safe installation Electrical shock can result in death or serious injury Avoid contact with the leads and terminals High voltage that may be present on leads can cause electrical shock A WARNING Explosion Hazard Do not disconnect equipment when a flammable or combustible atmosphere is present A IMPORTANT NOTICE The 1420 Wireless Gateway should be installed before installing any other wireless devices This will result in a simpler and faster network installation Physical Device Revision 1 0 Web Server Revision 3 0 8 Network Revision 1 0 Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway STEP 1 INITIAL CONNECTION FOR CONFIGURATION To configure the 1420 Wireless Gateway a local connection between a PC laptop and the 1420 Wireless Gateway must be established NOTE If a PC laptop from another network is used carefully record the current IP address and other settings so the PC laptop can be returned to its original network when configuration of the 1420 is finished Perform the following steps to establish a local connection with the 1420 Wireless Gateway 1 On the PC laptop install the Java Plug in found on the CD provided with the 1420 The Plug in can also be
16. w the navigation hierarchy Quick Installation Guide 00825 0100 4420 Rev CA June 2007 1420 Wireless Gateway STEP 2 BASIC SECURITY AND TIME CONFIGURATION To configure the basic security of the 1420 Wireless Gateway perform the following steps 1 Navigate to Setup gt Security gt User Accounts 2 Set and confirm new passwords for each of the access levels amp 1420 ini erri Wireless Gateway y B 192 168 110 HEY Diegnostics 5 monitor AA wareins SAE xplorer Use caution when changing the administrator password If the administrator password is lost you will not be oble to 4j Setup setup the 1420 iNetwork Biinternet protocol New Administrator Password amp Secunty Confirm 0 memme certificates New Maintenance Password access List Confirm O Time iE Page Options Now Operator Password J 3 Restart Apps Confirm QF HART M Modbus New Executive Password lt SOPE Confirm I lil Trends 3 Click Submit 4 Navigate to Setup Time n 1420 E EMERSON A S recen Me Wireless Gateway Y E 192 168 1 10 Gap Diagnostics i ri M T Your PC s time 11 17 06 09 41 26 921 ae 1420 time systemtest2 11 17 06 09 42 11 829 P CA Explorer Difforonco 0 days 00 00 44 908 S setup 4 qrietwork Method used to set time Network Time Protocol NTP Set with PC time Omanual entry Byinvernet protocol CJ Secunty D DHE Page Options Submit Restart apps AF HART

Download Pdf Manuals

image

Related Search

Related Contents

Copyright © All rights reserved.
Failed to retrieve file