Electrolux U01317 User's Manual
Contents
1. Servicing A Removal Of Control Panel Remove all the control knobs Using a levering action of the hand on the rear area of the panel pull it up until it disconnects from its hooks When doing this avoid using objects which could damage the hob and or the control panel B Removal Of Hob Top NO Follow the procedure in A 1 Remove the panstands and each burner cap and crown 2 Remove the 2 self tapping screws from each burner 3 Remove control panel as Section A and remove 1 self tapping screw from Hob Top C Removal Of the Hob Taps Isolate Electric Supply 1 Follow the procedures in Sections A and B 2 With the aid of a 7mm spanner remove the clamping bolt from the fixing clamp 3 Loosen the pipe connection nut from the gas tap with the aid of a 16mm spanner Remove fixing clamps 4 Reassemble in reverse order and carry out leak test D Removal Of Mains Terminal Block Isolate Electric Supply 1 Follow the procedures in Sections A and B C 2 Disconnect supply flex connections from terminal block 3 From the underside of the hob remove self tapping screw from the terminal block 4 Reassemble in reverse order E Removal Of Burner Follow the procedures in Sections A B and C With the aid a 12mm spanner loosen off the pipe connection nut 3 From the underside of the hob remove 2 self tapping screws from the burner body 4 Reassemble in reverse order and carry out leak test2. INSTRUCTION BOOKLET Models EHG 678 B EHG 678W KM Electrolux A Important Safety Information on 01635 522799 Installation This hob must be installed by qualified personnel according to the manufacturer s instructions and to the relevant British Standards Any gas installation must be carried out by a registered CORGI installer Remove all packaging before using the hob Ensure that the gas and electrical supply complies with the type stated on the rating plate located near the gas supply pipe Do not attempt to modify the hob in any way Child Safety This hob is designed to be operated by adults Do not allow children to play near or with the hob The hob gets hot when it is in use Children should be kept away until it has cooled Children can also injure themselves by pulling pans or pots off the hob During Use This hob is intended for domestic cooking only It is not designed for commercial or industrial purposes When in use a gas cooking hob will produce heat and moisture in the room in which it has been installed Ensure there is a continuous air supply keeping air vents in good condition or installing a cooker hood with a venting hose When using the hob for a long period time the ventilation should be improved by opening a window or increasing the extractor speed Do not use this hob if it is in contact with water Do not operate the hob with wet hands Ensure the control
3. Nuneaton CVII 6RX REDDITCH Heming Road M20 Washford Redditch Worcestershire B98 ODH TAMWORTH Unit 3 M19 Sterling Park Claymore Tamworth B77 5DO WORCESTER Unit 1 M73 Northbrook Close Gregorys Mill Ind Estate Worcester WR3 8BP CANVEY ISLAND CHELMSFORD M47 COLINDALE M53 ENFIELD M49 GRAVESEND M57 HARPENDEN M46 LETCHWORTH M50 LETCHWORTH M50 LONDON M76 MOLESEY M61 NEWBURY M24 IPSWICH M48 NORWICH M52 SUNBURY M63 SYDENHAM M62 2 4 Sandhurst Kings Road Canvey Island SS8 0OQY Hanbury Road Widford Ind Estate Chelmsford Essex CM12 3AE Unit 14 Capital Park Capital Way Colindale London NW9 0EQ 284 Alma Road Enfield London EN3 7BB Unit B4 Imperial Business Estate Gravesend Kent DA11 ODL Unit 4 Riverside Estate Coldharbour Lane Harpenden ALS 4UN 16 17 Woodsite Ind Est Works Road Letchworth Herts SG6 ILA 16 17 Woodsite Ind Est Works Road Letchworth Herts SG6 ILA 2 4 Royal Lane Yiewsley West Drayton Middlesex UB7 8DL 10 Island Farm Avenue West Molesey Surrey KT8 2UZ PO BOX 5672 Newbury Berkshire RG14 5GF Unit 2B Elton Park Business Centre Hadleigh Road Ipswich IP2 ODD 2b Trafalgar Street Norwich NRI 3HN Unit la The Summit Hanworth Road Hanworth Ind Estate Sunbury on Thames TW16 5D Unit 6 Metro Centre Kangley Bridge Road Sydenham SE26 SOUTH EAST ASHF
4. easily accessible for the engineer in the event of a breakdown Operation HOB BURNERS To light a burner turn the relevant knob anticlockwise to maximum position and push down the knob to ignite If the burner does not ignite turn the control knob to zero and try again When switching on the mains after H installation or a power cut it is quite normal for the spark generator to be activated automatically To ensure maximum burner efficiency you should only use pots and pans with a flat bottom fitting the size of the burner used see table minimum maximum diameter diameter Large rapid Medium semi rapid Small Auxiliary If you use a saucepan which is smaller than A the recommended size the flame will spread beyond the bottom of the vessel causing the handle to overheat As soon as a liquid starts boiling turn down H the flame so that it will barely keep the liquid simmering AN Take care when frying food in hot oil or fat as the overheated splashes could easily ignite A If the control knobs become difficult to turn please contact your local Electrolux Service Centre Maintenance and Cleaning A Before any maintenance or cleaning can be carried out you must DISCONNECT the hob from the electricity supply The hob is best cleaned whilst it is still warm as spillage can be removed more easily than if it is left to cool The Hob Top Regularly wipe over the hob top using a soft c
5. the tip of mains connector block and O on each electrode to the terminals 1 the ignitor unit to 4 on the ignitor unit Check continuity from L on the Check for breaks in the insulation mains connector block and the of the HT leads taps ignition switches Check continuity from ignition Change the taps ignition switches connector to ignitor unit switches Change the ignitor unit Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting To do this follow the procedure below Turn the gas tap to the MAX position and ignite Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times If the flame is unstable or is extinguished follow the procedure below Procedure IS Re ignite the burner and set to MIN Remove the control knob insert a thin bladed screwdriver down the centre of the gas tap control shaft and turn the adjustment screw until the flame is steady and does not extinguish when the knob is turned from MIN to MAX Repeat this procedure for all burners Pressure Testing IS Remove left hand pan support and front left burner cap and crown Fit manometer tube over the injector Turn on the burner gas supply and ignite another burner supply The pressure reading should be nominally 20mbar and must be between 17 mbar and 25mbar Turn off the burner supplies 20 a Minimum adjustment screw b Tap
6. 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 20 78 77 50 UK Newbury 44 0 1635 522 799 SSERVICESFORCE 4 To contact your local Electrolux Service Force Centre telephone 0990 929929 CHANNEL ISLANDS GUERNSEY JERSEY Guernsey Electricity PO Box 4 Vale Guernsey Channel Islands Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABERDEEN M05 AUCHTERMUCHY M03 BLANTYRE M07 DUMFRIES M01 DUNOON M 67 GLASGOW M04 INVERNESS M06 ISLE OF ARRAN OWN SALES ISLE OF BARRA OWN SALES ISLE OF BUTE M66 10 8 Cornhill Arcade Cornhill Drive Aberdeen AB2 5UT 33A Burnside Auchtermuchy Fife KY14 7AJ Unit 5 Block 2 Auchenraith Industrial Estate Rosendale Way Blantyre G72 ONJ 93 Irish Street Dumfries Scotland DGI 2PQ Briar Hill 7 Hill Street Dunoon Argyll PA23 7AL 20 Cunningham Road Clyde Estate Rutherglen Glasgow G73 1PP Unit 3B Smithton Indust Est Smithton Inverness IV1 2PD Arran Domestics Unit 4 The Douglas Centre Brodick Isle of Arran KA27 8AJ J Zerfah 244 Bruernish Isle of Barra Western Islands HS9 5QY Walker Engineering Glenmhor Upper Serpentine Road Rothesay Isle of Bute PA20 9EH ISLE OF LEWIS M69 KELSO MOS ORKNEY M65 SHETLAND OWN SALES SHETLAND OWN SALES WHALSAY OWN SALES ND Macleod 1
7. 6 James Street Stornoway Isle of Lewis PA872QW 2 8 Wood Market Kelso Borders TD5 TAK Corsie Domestics 7 King Street Kirkwall Orkney KW15 IRE Tait Electronic Systems Ltd Holmsgarth Road Lerwick Shetland ZEl OPW Bolts Shetland Ltd 26 North Road Lerwick Shetland ZEl OPE Leask Electrical Harlsdale Symbister Whalsay Shetland ZE2 9AA NORTHERN IRELAND BELFAST M27 Ovvenmore House Rilvvee Industrial Estate Upper Dunmury Lane Belfast BT17 OHD VVALES CARDIFF M28 CLYWD M14 OSWESTRY M17 HAVERFORDWEST M75 Guardian Industrial Estate Clydesmuir Road Tremorfa Cardiff CF2 2QS Unit 6 7 Coed Parc Abergele Road Rhuddlan Clwyd Wales LL18 5UG Plas Funnon Warehouse Middleton Road Oswestry SY11 2PP Cromlech Lodge Amerlston Haverfordwest SA62 5DS ELECTROLUX SERVICE FORCE IM NORTH EAST GATESHEAD M39 Unit 356a Dukesway Court Dukesway Team Valley Gateshead NE11 OBH GRIMSBY M42 Unit 2 Cromwell Road Grimsby South Humberside DN31 2BN HULL M41 Unit 1 Boulevard Industrial Estate Hull HU3 4AY LEEDS M37 64 66 Cross Gates Road Leeds LS15 7NN NEVVTON AYCLIFFE Unit 16 M45 Gurney Way Aycliffe Ind Estate Newton Aycliffe DLS 6UJ SHEFFIELD M38 Pennine House Roman Ridge Ind Roman Ridge Road Sheffield S9 1GB NORTH WEST BIRKENHEAD M11 1 Kelvin Park Dock Road Birkenhead L41 1LT CARLISLE M10 U
8. M The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles Check the burner cap and crown have been replaced correctly e g after cleaning If after all these checks your hob still does not In guarantee customers should ensure that the operate correctly contact your local Electrolux above checks have been made as the engineer will Service Force Centre make a charge if the fault is not a mechanical or electrical breakdown Please note that it will be necessary to provide proof of purchase for any in guarantee service calls Service and Spare Parts If you require spare parts or an engineer contact your CUSTOMER CARE local Service Force Centre by telephoning For general enquiries concerning your Electrolux appliance and for further information on Electrolux 0990 929929 products contact our Customer Care Department by letter or telephone as follows Your call will be routed to the Service Centre Customer Care Department covering your post code area The addresses of Li Electrolux Service Force Centres are detailed on the EO pee PO Box 47 ollowing pages Newbury l RG14 5XL When you contact the Service Centre they will need Tel 01635 52 27 99 the following information 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and the serial number see rating label on the back of this instruction boo
9. NO F Removal Of Ignitor Unit Isolate Electric Supply 1 Follow the procedures in Sections A B and C 2 Disconnect H T leads and the ignition switches connector 3 With the aid of a pair of thin nose pliers pull the spring clip sidewards off of the underside of the ignitor 4 Reassemble in reverse order and check with wiring diagram for correct reconnection G Remove Taps Ignition Switches Isolate Electric Supply 1 Follow the procedures in Sections A B and C 2 Disconnect the switches connector from the ignitor unit and remove the supply cables pulling the tabs connection off 3 Reassemble in reverse order and check with wiring diagram for correct reconnection Repais may only be carried out by CORGI registered engineers Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted The gas rate is adjusted to suit Method e Ensure that the gas taps are in the OFF position e Isolate the hob from the electricity supply e Remove all pan supports burner caps rings crowns and control knobs e With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors TO ADJUST THE GAS RATE With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment screw which is located
10. ORD M58 FLEET M59 HAYWARDS HEATH M55 TONBRIDGE M56 Unit 2 Bridge Road Business Estate Bridge Road Ashford Kent TN2 1BB Unit 1 Redfields Industrial Estate Church Crookham Fleet Hampshire GU13 ORD 21 25 Bridge Road Haywards Heath Sussex RH16 IUA Unit 30 Deacon Trading Estate Morley Road Tonbridge Kent TN9 IRA SOUTH WEST BARNSTAPLE M30 BOURNEMOUTH M26 BRIDGEWATER M35 BRISTOL M25 EMSWORTH M33 ISLE OF WIGHT M34 NEWTON ABBOT M29 PLYMOUTH M32 REDRUTH M36 P O Box 12 Barnstaple North Devon EX31 2YB 63 65 Curzon Road Bournemouth Dorset BH1 4PW 6 Hamp Industrial Estate Bridgewater Somerset 11 Eldon Way Eldonwall Trading Bristol Avon BS4 3QQ 266 Main Road Southboure Emsworth PO10 8JL Unit 8 Enterprise Court Ryde Business Park Ryde Isle of Wight PO33 1DB Unit 2 Zealley Industrial Estate Kingsteignton Newton Abbot S Devon TQ12 3TD 16 Faraday Mill Cattledown Plymouth PL4 OST Unit 7D Pool Industrial Estate Wilson Way Redruth Cornwall TRIS 3QW 11 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS SUPPLY CONNECTIONS Width 580 mm Depth 500 mm Gas l Height Re fai RC 1 2 inch 1 2 inch male Rear right hand corner Weight 8 5 Kg Daie 230 240V 50Hz supply 3 core flexible cable with CUT OUT DIMENSIONS non rewireable plug fitted with a 3 a
11. as shown in the diagram FO 0402 a Sealing gasket 15 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person in accordance with the current regulations THIS HOB MUST BE EARTHED The manufacturer declines any liability should these safety measures not be observed This hob is designed to be connected to a 230 240V 50Hz AC electrical supply Before switching on make sure the electricity supply voltage is the same as that indicated on the hob rating plate The rating plate is located on the bottom of the hob A copy is attached on the back cover of this book The hob is supplied with a 3 core flexible supply cord incorporating a 3amp plug fitted In the event of having to change the fuse a 3amp ASTA approved BS 1362 fuse must be used Should the plug need to be replaced for any reason the wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live Connect the green and yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow Connect the blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black Connect the brown live wire to the terminal in the plug which is marked with the letter L or coloured red Upon completi
12. down the centre of the gas tap control shaft Upon completion stick the replacement rating plate on the under side of the hob IMPORTANT The replacement conversion of the gas hob should only be undertaken by a competent person 21
13. klet 5 Date of purchase Guarantee Conditions ELECTROLUX STANDARD GUARANTEE CONDITIONS We Electrolux undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by a Electrolux Service Force Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an applia
14. knobs are in the OFF position when not in use You MUST read these warnings carefully before installing or using the hob If you need assistance contact our Customer Care Department When using other electrical appliances ensure the cable does not come into contact with the hot surfaces of the cooking appliance Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage Never leave the hob unattended when cooking with oil and fats Never use plastic or aluminium foil dishes on the hob Perishable food plastic items and areosols may be affected by heat and should not be stored above or below the hob unit Service This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used Environmental Information After installation please dispose of the packaging with due regard to safety and the environment When disposing of an old appliance make it unusable by cutting off the cable Keep this instruction book for future reference and ensure it is passed on to any new owner For the User Description of the Hob Operation Maintenance and Cleaning Something Not Working Service and Spare Parts Guarantee Conditions Contents Page Page Page Page Page Page Electrolux Service Force Centre Addresses Guide to Use the instructions The following symbol
15. loth well wrung out in warm water to which a little wasing up liquid has been added Avoid the use of the following household detergent and bleaches impregnated pads unsuitable for non stick saucepans steel wool pads bath sink stain removers Should the hob top become heavily soiled it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used Pan Supports The pan supports are dishwasher proof If washing them by hand take care when drying them as the enamelling process occasionally leaves rough edges If necessay remove stubborn stains using a paste cleaner The Burners The burner caps and crowns can be removed for cleaning Wash the burners taps and crowns using hot soapy water and remove marks with a mild paste cleaner A well moistened soap impregnated steel wool pad can be used with caution if the marks are particularly difficult to remove After cleaning be sure to wipe dry with a soft cloth Something Not Working If the hob is not working correctly please carry out the following checks before contacting your local Electrolux Service Force Centre SYMPTOM SOLUTION M There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped if fitted Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly e g after cleaning
16. mp cartridge Width 550 mm fuse Depth 470 mm Thickness 30 mm This appliance complies with the EEC Directive No 89 336 concerning suppression of radio electrical interference Ignition HT Spark Spark Generator Ispra Control s BF 50046 230 240V 0 6 YA T 120 Spark Gap Fixed Rear Left Burner semi rapid Heat Input 2 0 kW 6824 BTU HR Rear Right Burner Semi rapid Heat Input 2 0 kW 6824 BTU HR Front Left Burner rapid Heat Input 3 0 kW Natural Gas 10236 BTU HR Front Right Burner auxiliary 2 8 kW L P G 9554 BTU HR Heat Input 1 0 kW 3412 BTU HR BURNER RAPID SEMI RAPID AUXILIARY large medium small NOMINAL THERMAL POWER kW TYPE OF GAS CHARACTERISTICS 37 78 MJ m 50 7 MJ m m h 0 057 MN lt 0 3 ian SE E lt Z NOZZLE REFERENCE Adjust 1 100 mm NOMINAL THERMAL POWER kW VALUE Ws 49 92 MI Kg NOMINAL FLOW RATE g h 28 30 37 mbar LPG GAS VALUE NOZZLE REFERENCE 1 100 mm CLASS APPLIANCE 3 Burner Dia Tap By pass Tap colour 1 100 mm APPLIANCE Auxiliary Red Red CATEGORY II2H3 Semi rapid Blue Blue Rapid Black Black APPLIANCE GAS SUPPLY Natural gas G20 20mbar Aeration adjustment none 12 Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regulations Current Edition and the IEE Wiring Regulations Current Edition Detailed recommendations are contained in the follo
17. nce which is improperly installed or calls to appliance outside the United Kingdom Appliances found to be in use within a commercial or similar environment plus those which are the subject to rental agreements Products of Electrolux manufacture which are not marketed by Electrolux European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exist in the new contry of use for this brand or range of products This guarantee relates to you and cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically 1 e a normal household The electrical supply complies with the specification given in the rating label The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 22 22 Germany N rnberg 49 0 911
18. nce must be electrically disconnected meter set on 42 Ohms x 1 scale and adjust zero if necessary a Test leads from any appliance earth point to earth pin on plug Resistance should be less than 0 1 Q Ohm check all earth wires for continuity and all contacts clean and tight B INSULATION CHECK Appliance electrically disconnected all switches ON a meter set on Q Ohms x 1 scale Test leads from L to N in appliance terminal block If meter reads 0 then there is a short circuit b meter set on Q Ohm x 100 scale Repeat test with leads from L to E If meter reads less than infinity there is a fault NOTE Should it be found that the fuse has failed but no fault is indicated a detailed continuity check i e by disconnecting and checking each component is required to trace the faulty component It is possible that a fault could occur as a result of local burning arcing but no fault could be found under test However a detailed visual inspection should reveal evidence of burning around the fault Ignition System Gas Ignition YE Ignitor does not spark S Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check by pass simmer Check polarity and earth adjusted continuity of supply point Check position of the Check earth continuity electrode of appliance Check fitting of burners Check continuity from N on the Check continuity from
19. nit 8 South John Street Carlisle CA2 5AJ ISLE OF MAN M64 South Quay Ind Estate Douglas Isle of Man LIVERPOOL M15 Unit 1 Honeys Green Precinct Honeys Green Lane Liverpool L12 9JH MANCHESTER Unit 30 Oakhill Trading Estate Devonshire Road Worsley Manchester M28 3PT M09 PRESTON M13 Unit 250 Dawson Place Walton Summit Bamber Bridge Preston Lancashire PR5 8AL STOCKPORT M16 Unit 20 Haigh Park Haigh Avenue Stockport SK4 IQR eames ELECTROLUX SERVICE FORCE a gua To contact your local Electrolux Service Force Centre telephone 0990 929929 LONDON amp EAST ANGLIA MIDLANDS BIRMINGHAM 66 Birch Road East M18 Wyrley Road Industrial Estate Witton Birmingham B67DB BOURNE Manning Road Ind M44 Estate Pinfold Road Bourne PE10 9HT BRIDGNORTH 1 Underhill Street M72 Bridgnorth Salop WV 16 4BB GLOUCESTER 101 Rycroft Street M23 Gloucester GLI 4NB HEREFORD Unit 3 M31 Bank Buildings Cattle Market Hereford HE4 9HX HIGHAM FERRERS The Old Barn M51 Westfield Terrace Higham Ferrers NN10 8BB ILKESTON Unit 2 M43 Furnace Road Ilkeston DE7 5EP LEICESTER Unit 7 M22 Oaks Industrial Estate Coventry Road Narborough Leicestershire LEO 5GF LINCOLN Unit 8 Stonefield Park M40 Clifton Street Lincoln LNS 8AA NEWCASTLE 18 21 Croft Road UNDER LYME Brampton Industrial M12 Estate Newcastle under Lyme Staffordshire STS OTW NUNEATON 19 Ptarmigan Place M21 Townsend Drive
20. on there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath A cut off plug inserted into a 13 amp A socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely 16 Permanent Connection In the case of a permanent connection it is necessary that you install a double pole switch between the hob and the electricity supply mains with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations The switch must not break the yellow and green earth cable at any point Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg C GREEN amp YELLOW 3 AMP FUSE CORD CLAMP Wiring diagram o lo io oro 1 TAPS IGNITOR SWITCHES 2 IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check 18 Has inlet fuse blown START Isolate appliance and carry out A Earth Continuity check Carry out C Polarity check Inlet wiring faulty Rectify any fault Isolate appliance and carry out B Insulation check Rectify any fault including replacing fuses as necessary Green Yellow PLUG with cover removed SOCKET face view Carry out Electricity supply D Resistance to should now be Earth check satisfactory A EARTH CONTINUITY CHECK Applia
21. rom the edges of the hob The minimum distance combustible material can be fitted directly above the hob is 700 mm INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE I 600 mm FO 0813 13 Installation IMPORTANT This hob must be installed by qualified AN personnel to the relevant British Standards Any gas installation must be carried out by a registered CORGI installer The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this book be ignored On the end of the shaft which includes the GJ 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force Gas Connection Connection to the gas supply should be with either rigid or semi rigid pipe 1 e steel or copper The connection should be suitable for connecting to RC 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation Ensure that the main connection pipe does not exert any strain on the hob A It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Failure to ensure the correct assembly will cause leakage of gas Cut Out Size The dimensions of
22. s will be found in the text to guide you throughout the Instructions AN Safety Instructions Page 10 Step by step instructions for an operation 1 Hints and Tips For the Installer Technical Data Important Safety Requirements Installation Gas Connection Building In Electrical Connection Wiring Diagram Fault Finding Commissioning Servicing Conversion from natural gas to LPG Page Page Page Page Page Page Page Page 12 13 14 14 15 16 17 18 Page 20 Page 21 Page 21 This appliance is manufactured according to the following EEC directives 73 23 EEC 90 683 EEC 93 68 EEC 89 336 EEC 90 396 EEC current edition Description of the Hob 1 2 3 Hob Top Rapid Burner Semi rapid Burners Auxiliary Burner Control Panel Control knob for back left burner semi rapid Control knob for front left burner rapid Control knob for front right burner auxiliary Control knob for back right burner semi rapid OON NU BEL N INSTALLATION WHEN THE HOB IS FIRST INSTALLED Any gas installation must be carried out by Once the hob has been installed it is AN a registered CORGI installer and in AN important to remove any protective accordance with existing rules and materials which were put on in the factory regulations The relevant instructions are to be found in the second section of this manual A Please ensure that once the hob is installed it is
23. the cut out are given in the diagram 14 FO 0814 A End of shaft with nut B Washer C Elbow Rectangular cut out size for hob Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or It is also recommended to carry out the electrical drawer it will be necessary to fit a heat resistant board connection to the hob as shown in diagrams 1 and 2 below the base of the hob on the underside of the work surface ON OFF SWITCH ON OFF SWITCH OUTLET FO 0764 Dimensions are given in mm Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit in order to avoid any contact with the bottom of the hob which can be heated when it is operated The recommended solution is shown in diagram 3 The panel fitted under the hob a should be easily removable to allow easy access if technical assistance is needed The space behind the kitchen unit b can be used for connections Fitting the hob to the worktop Before fitting the hob into the cut out an adhesive sealing gasket supplied with the hob must be fitted to the edge of the cut out It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below 1 Place the sealing gasket all around the edge of the cut out 2 Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws
24. wing British Standards Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m If it is installed in a room of volume less than 5 m an air vent of effective area of 110 cm is required If it is installed in a room of volume between 5 m and 10 m an air vent of effective area of 50 cm is required while if the volume exceeds 11 m no air is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 mand 11 m If there are other fuel burning appliances in the same room B S 5440 Part 2 Current Edition should be consulted to determine the requisite air vent requirements INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE FO 0812 Location The hob may be located in a kitchen a kitchen diner or bed sitting room but not in a bathroom or shower room Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm between the rear edge of the hob and the wall A minimum distance of 100 mm must be left between the side edges of the hob and any adjacent cabinets or walls The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 420 mm If it is fitted below 420 mm a space of 50 mm must be allowed f
Download Pdf Manuals
Related Search