Electrolux EKG5543 User's Manual
Contents
1. Always use oven gloves to remove and place food in the oven Ensure cooking utensils are large enough to contain foods to prevent spillages and boil overs During use the appliance becomes hot Care should be taken to avoid touching the heating elements inside the oven Ensure that all vents are not obstructed to ensure ventilation of the oven cavity Never line any part of the appliance with foil Always stand back from the appliance when opening the oven door to allow any build up of steam or heat to release Never leave the appliance unattended when the oven doors are open Do not place sealed cans or aerosols inside the oven They may explode if they are heated Ensure that all control knobs are in the OFF position when not in use Do not stand on the appliance or on the open oven doors Do not hang towels dishcloths or clothes from the appliance or its handles Do not use this appliance if it is in contact with water Never operate it with wet hands CLEANING AND MAINTENANCE For hygiene and safety reasons this appliance should be kept clean at all times A build up of fats or other foodstuffs could result in a fire especially in the grill pan Do not leave cookware containing foodstuffs e g fat or oil in the appliance in case it is inadvertently switched on Do not disconnect the appliance from the gas supply if the supply pipe does not have a bayonet connection as described in the installation section If this2. dl dl dl Din p JN Control Panel Grill Main Oven 4 GETTING TO KNOW YOUR APPLIANCE THE CONTROL PANEL K Electrolux INSIGHT WI FEATURES Hotplate Control Hotplate Control Main Oven Temperature Control Grill Control m o OF WD gt Hotplate Control F Hotplate Control G Ignition Switch BEFORE USING THE APPLIANCE RATING PLATE This is situated on the front frame of the appliance and can be seen upon opening the door Alternatively the rating plate may also be found on the back or top of some models where applicable The appliance must be protected by a suitably rated fuse or circuit breaker The rating of the appliance is given on the rating plate Do not remove the rating plate from the appliance as this may invalidate the guarantee PREPARING TO USE YOUR APPLIANCE Wipe over the base of the overn s with a soft cloth and hot soapy water and wash the furniture before use We suggest that you run the oven s and grill for 10 15 minutes at maximum temperature to burn off any residue from their surfaces Accessible parts may become hotter than in normal use Children should be kept away During this period an odour may be emitted it is therefore advisable to open a window for ventilation THE COOLING FAN FOR THE CONTROLS The cooling fan comes on immediately when the grill top oven is switched on and after a short time when
3. Ensure the hose does not become trapped when pushing the appliance into position IMPORTANT FLEXIBLE TUBING USED MUST COMPLY WITH BS 669 CURRENT EDITION LPG Flexible connections must be a type suitable for L P G and capable of operation up to 50 mbar and carry a red stripe band or label FITTING THE STABILITY CHAIN lt is recommended that if the appliance is to be installed with a flexible supply pipe a stability chain be fitted and is available from your supplier see Important Safety Requirements These instructions should be read in conjunction with any leaflet packed with the stability chain 1 Place the appliance in its intended position and level appliance 2 Mark a position 100mm from the top of the rear right hand corner 3 Measure down 150mm from this point This gives the position of the wall anchor point for the stability chain 4 The stability chain anchor point on the appliance is shown in the diagram Fig 4 PRESSURE TESTING 1 The Rapid injector is used as a pressure test point 2 Connect the pressure gauge to the Rapid injector 3 Check the supply pressure by turning the Rapid burner on and one other hotplate burner full on and light the appropriate burner The pressure should be either i For Natural Gas 20mbar ii For LP Gas The pressure must be set to 29 mbar for use on butane or 37 mbar for use on propane 4 Turn off the taps disconnect the pressure gauge 5 Check operation
4. Model EKG5542 EKG5543 INSIGHT IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using the appliance Your safety is of paramount importance If you are unsure about any of the information in this book contact the Customer Care Department INSTALLATION The appliance must be installed according to the instructions supplied The installation work must be undertaken by a competent person as stated in the Gas Safety Installation amp Use Regulations current editions and the IEE Wiring Regulations The appliance should be serviced by an authorised Service Engineer and only genuine approved spare parts should be used It is important that the appliance is suitable for your gas supply Your installer should check the rating plate Make sure that a stability chain is fitted The appliance must be installed in an adequately ventilated room If the appliance is to be placed on a base measures must be taken to prevent the appliance from slipping from the base This appliance is heavy and care must be taken when moving it Do not attempt to lift or move this appliance by the handles All packaging both inside and outside the appliance must be removed before the appliance is used It is dangerous to alter the specifications or modify the appliance in any way After installation please dispose of the packaging with due regard for
5. Set the oven control to Mk 2 close the oven door and check that after about 10 minutes the flame size has reduced 6 Turn off the control and check that the oven flames go out GENERAL NOTE Instruct the user on how to use the appliance and its ignition system Refer the user to the wording on the inside cover which gives advice on the safe operation of the appliance 30 NOTES 31 IMPORTANT NOTICE In line with our continuing policy of research and development we reserve the right to alter models and specifications without prior notice This instruction booklet is accurate at the date of printing but will be superseded if specifications or appearance are changed ELECTROLUX MAJOR APPLIANCES ADDINGTON WAY LUTON BEDFORDSHIRE LU4 9QQ TELEPHONE 0870 5 950950 To buy accessories consumables and spare parts at our online shop please visit http www electrolux co uk Part Number 349095904
6. The oven temperatures are intended as a guide only It may be necessary to increase or decrease the temperatures to suit individual preferences and requirements FOOD POSITION GAS POSITION APPROX MARK COOK TIME min Biscuits 2 4 4 3 10 20 Bread 3 8 30 40 Bread rolls buns 2 8 10 20 Cakes Small amp Queen 2 4 5 3 15 25 Sponges 2 4 4 3 18 20 Victoria Sandwich 7 2 4 4 3 20 30 Madeira 7 4 4 1 11 4 Rich Fruit 8 4 2 22h 23 4 Christmas 8 4 2 4 5h depends on size Gingerbread 3 2 3 114 1Yh Meringues 5 1 3 2 3h Flapjack 3 5 3 25 30 Shortbread 3 3 3 45 65 Casseroles Beef Lamb 4 3 3 2 3h Chicken 4 4 3 1 4 1 eh Convenience Foods Follow manufacturer s instructions Fish 2 4 3 20 30 Fish Pie Potato Topped 3 6 3 20 25 Fruit Pies Crumbles 3 6 3 40 50 Milk Puddings 3 3 3 1 2h Pasta Lasagne etc 3 5 3 30 40 Pastry Choux 2 6 3 30 35 Eclairs Profiteroles 2 5 3 20 30 Flaky Puff Pies 2 6 3 25 40 Shortcrust Mince Pies 2 4 5 3 15 20 Meat Pies 2 7 3 25 35 Quiche Tarts Flans 2 5 3 25 45 Roasting Meat Poultry 3 5 3 see roasting chart Scones 2 4 7 3 8 12 Shepherd s Pie 3 7 3 30 40 Souffl s 3 5 3 20 30 Vegetables Baked Jacket Potatoes 2 5 3 1h 2h Roast Potatoes 2 6 3 1 1Yh Yorkshire Pudding Large 2 7 3 25 40 Individual 2 7 3 15 25 When baking bread cook for 10 minutes at gas mark 8 then reduce to mark 6 for the remaining cook time Note Shelf positions are co
7. e Dried beans must be pre soaked then boiled in an open pan for 15 minutes before adding to any dish e Place vegetables under meat in casseroles e Cover food with a tight fitting lid or tin foil MILK PUDDINGS e Cover the cereal with boiling water and leave it to stand for 30 minutes e Drain and make the pudding in the usual way GENERAL POINTS FOR SLOW COOKING Frozen Foods Thaw thoroughly before cooking Thickening Toss meat in flour for casseroles Alternatively blend cornflour with water and add it at the end of cooking Flavouring Flavours are held in the food because there is little evaporation Adjust flavouring at the end of the cooking time Liquid Use slightly less liquid as there is little evaporation during cooking Always add milk and milk products for example cream towards the end of cooking to prevent them from curdling Reheating Cool left over food quickly and then put it in the fridge Do not reheat food using the slow cook setting Reheat food in the usual way or in a microwave Only reheat food once 16 CARE AND CLEANING Before cleaning always allow the appliance to cool down before switching off at the electricity supply CLEANING MATERIALS Before using any cleaning materials on your appliance check that they are suitable and that their use is recommended by the manufacturer Cleaners that contain bleach should NOT be used as they may dull the surface finishes Harsh abr
8. safety and the environment Your local authority can arrange this CHILD SAFETY Do not allow children to play with any part of the packaging Do not allow children to sit or climb on the drop down doors This appliance is not intended for use by children and other persons whose physical sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely Children should be supervised to ensure that they do not play with the appliance CAUTION Accessible parts may be hot when the grill is in use Young children should be kept away DURING USE This appliance is not intended to be operated by means of an external timer or separate remote control system This appliance has been designed for domestic use to cook edible foodstuffs only and must not be used for any other purposes Take great care when heating fats and oils as they will ignite if they become too hot When you are lighting any burner check that it is lit before you leave the appliance When turning off a burner do not leave the appliance until the flame has gone out Never place plastic or any other material that may melt in or on the oven Do not leave the grill pan handle in position when grilling as it will become hot Always support the grill pan when it is in the withdrawn or partially withdrawn position
9. 230 240 V 50 Hz Mains connected at rear centre of appliance using at least 2 5mmz2multi core PVC insulated cable Natural Gas R H F R H F 1 0kW 1 9kW 3412 Btu h 6483 Btu h 070 096 L P Gas 1 0kW 2 0kW 71 8g h 143 6g h 050 071 Natural Gas 2 7kW 9212 Btu h 120 1 9kW 6483 Btu h 099 75 75 H T Spark 3 4mm GAS CATEGORY COUNTRIES OF DESTINATION CAT l2 CAT l3 GB GB L H R L H F 1 9kW 3 0kW 6483 Btu h 10236 Btu h 096 119 2 0kW 2 8kW 143 6g h 194 0g h 071 086 L P Gas 2 7KW 1949 h 95 1 9kW 136 5g h 070 80 80 C This appliance complies with European Council Directives Low voltage Directive 73 23 EEC Gas Directive 90 396 EEC EMC Directive 89 336 EEC CE Marking Directive 93 68 EEC 25 INSTALLATION INSTRUCTIONS IMPORTANT SAFETY REQUIREMENTS Where applicable Natural Gas and L P Gas versions of this appliance are available Check that this model is suitable for the type of supply available This appliance must be installed and or serviced by a competent person in accordance with the Gas Safety Installation and Use Regulations Current Editions and the E E Wiring Regulations Detailed recommendations are contained in the following British Standard Codes of Practice BS 6172 BS 5440 Part 2 and B S 6891 All British Standards must be Current Editions This appliance must be installed by a qualified electrician competent person CORGI Registe
10. ING THE HOB The gas hob has different burner sizes to suit different types of cooking To ensure maximum burner efficiency only use pots and pans with flat bases appropriate to the burner size used Larger burner Rapid or triple crown where applicable use a large pan for food such as chips Medium burners Normal use for everyday cooking Small burner Simmer use for simmering foods such as soups and stews The largest pan which you should use on any burner is 230mm 9 The base of the smallest pan should not measure less than 100mm 4 Ensure the pan supports are correctly fitted before using the hob TO LIGHT THE HOB BURNERS The hob ignition works by means of an electric spark system 1 Lift up the lid You cannot use the hob when the lid is down 2 Push in and turn the control knob to the left to the highest setting This is shown by a large flame symbol Press the ignition button immediately 3 When the burner has lit release the control and ignition button adjust the setting as required Warning If the ignition button is not pressed immediately a build up of gas may cause the flame to spread any of the hotplate burners are lit the gas will go out This is because it would be dangerous if the burners stayed on when the lid was closed Always use the control knob to turn off a burner Do not use the lid as a cut off device This will only cut off the gas when the lid is closed The gas will flo
11. able outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are subject to rental agreements Products of Electrolux manufacture which are not marketed by Electrolux 24 TECHNICAL DETAILS DIMENSIONS Height Width Depth Weight 900 mm nominal 550 mm nominal 600 mm to front of door panel 58 Kg Net Space for fixing at hotplate level 2mm minimum clearance Space for fixing above hotplate level See important note Location of Appliance Minimum space above hotplate 750mm If cooker hood is fitted refer to the cooker hood installation instructions Minimum distance from rear wall 5mm spacer given by pressed spacer on vent panel CONNECTIONS Gas connection Electrical connection HOTPLATE Heat Input Injector Marking Heat Input Injector Marking GRILL Heat Input Injector Marking MAIN OVEN Heat Input Injector Marking Thermostat By Pass Marking Thermostat By Pass Marking GENERAL Ignition Spark Gap Rear left hand side of appliance at hotplate level Re 1 Y B S P female
12. age the spark electrodes If the spark electrodes are damaged the burners will not light You can remove the pan supports burner caps and burner crowns to clean them Again take care not to damage the spark electrodes Clean the burner crowns and pan supports by soaking them in very hot soapy water Aluminium based saucepans can leave shiny metal marks on the pan supports You can remove any stubborn stains by scouring with a soap impregnated steel wool pad If you look after the burner crowns and pan supports in this way they will stay reasonably clean However the surface will dull with time After cleaning the appliance parts dry them thoroughly before you put them back WHEN REPLACING HOTPLATE BURNER PARTS 1 Crown to body Do not try to force the crown on to the body Make sure that the hole in the crown is over the electrode Check that the location pegs sit in the slots in the body When the crown is in this position let it fall freely on to the body Check that the crown can be moved slightly from side to side 2 Cap to crown Place cap centrally on the top of crown enamel side up Move sideways and front to back to check the cap is properly fitted 3 Check for ignition If a burner will not light then you need to check the crown and cap positions CLEANING THE SHELVES WIRE WORK RUNNERS AND GRILL OVEN FURNITURE All removable parts except the grill pan handle can be washed in the dishwasher The grill pa
13. asives must also be avoided CLEANING THE OUTSIDE OF THE APPLIANCE Do not use abrasive cleaning materials e g Hob Brite Brillo pads or scourers on painted or printed finishes as damage may occur Regularly wipe over the control panel doors and appliance sides using a soft cloth and hot soapy water To prevent streaking finish with a soft cloth Stainless Steel cream cleaners are abrasive and should be avoided as they may dull the surface finish Any spillage on the stainless steel finish must be wiped off immediately Do not attempt to remove any of the control knobs from the appliance as this may cause damage and is a safety hazard CLEANING THE CONTROL KNOBS AND HANDLES It is strongly recommended that only hot soapy water is used for cleaning the control knobs and handles ANY OTHER CLEANING MATERIALS MAY DULL THE SURFACE FINISH REMOVING AND REPLACING THE WIREWORK RUNNERS 1 Remove all shelves and furniture from the oven Hold the wirework at the bottom unclip from the cavity side and gently pull towards the centre of the oven 3 Unhook the runner at the top and remove from the cavity 4 To replace the runners hook the wirework side runner into the cavity slide back and press into place Ensure the wirework runners are firmly in position before replacing the oven shelves 17 SIDE PANEL CAVITY CENTRE CLEANING THE HOB Clean the hotplate top using a mild abrasive Take care not to dam
14. concerning your Electrolux appliance or for further information on Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www electrolux co uk Customer Care Department Electrolux Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel 0870 5 950950 calls to this number may be recorded for training purposes 23 GUARANTEE CONDITIONS Standard guarantee conditions We Electrolux undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by a Service Force Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be avail
15. cooker hoods if recommended by manufacturers instructions and 400mm above the hotplate when fitted in line with the outside of the appliance If the units are intended to be fitted adjacent to the appliance but less than 400mm above the hotplate then a minimum space of 50mm must be maintained between the sides of the unit and the appliance See Fig 1b Curtains must not be fitted immediately behind the appliance or within 150mm of the sides of the hotplate If fitted next to or between two base units a minimum space of 2mm must be left between each unit and the sides of the appliance The levelling feet fitted to the appliance will achieve a nominal height to hotplate of 900mm 20mm Note L P G cookers MUST NOT be installed below ground level i e in a basement or aboard any boat yacht or other vessel LEVELLING THE APPLIANCE Adjustment to suit floor conditions or height is obtained by rotating clockwise or anti clockwise the feet at the front and rear of the appliance A spirit level should be placed on one of the shelves to confirm the appliance is correctly levelled 27 Wall Cabinets Cooker Hoods Wall Cabinets Cooker Hoods All dimensions in mm Fig 1 a CONNECTING TO THE ELECTRICITY SUPPLY Warning This appliance must be earthed Do not earth this appliance to the gas supply piping Connect to 230 240 A C supply only Connection to the electricity supply should be made via a properly earthed readi
16. e POSSIBLE SOLUTION Check that the appliance has been wired in to the appliance supply and is switched on at the wall Check that there is not a problem with your gas supply You can do this by making sure the other gas appliances such as central heating or gas fires are working Check that the main appliance fuse is working If you have checked the above Allow the appliance to cool for a couple of hours The appliance should now be working normally Check that the appliance is correctly installed and is level Check that the recommended temperatures and shelf positions are being used The oven light bulb may need replacing Check that the recommended temperatures and shelf positions are being used Be prepared to adjust the temperature up or down slightly to achieve the results you want Refer to the Main Oven section Check that there is not a problem with your electricity supply Ensure the burner parts have been placed correctly Check that there is not a problem with your gas supply You can do this by making sure the other gas appliances such as central heating or gas fires are working Due to the design of the burner the flame can appear to be orange yellow flame disturbance in certain areas of the burner this is a natural occurrence Check that the burner is dry and that food spillage or cleaning fluids are not present on the burner This can be dried with a cloth and stubborn marks cleaned away with a dry ny
17. e Some smoke from fat splashes may be evident as the grill cleans itself Never cover the grill pan or grid with foil as this can lead to grill fires THE GRILL PAN AND HANDLE The grill pan is supplied with a removable handle To attach the handle press the button on the handle with the thumb and insert the lip into the widest part of the bracket Slide the handle towards the left and release the button A Ensure the handle is correctly located To remove the handle press the button on the handle with the thumb and slide the handle towards the right Release the button Always remove the grill pan handle during grilling Place the grill pan on the shelf so that the pan is positioned centrally beneath the grill Ensure that the cut out on the underside of the handle bracket locates between the bars of the shelf i HINTS AND TIPS e Most foods should be placed on the grid in the grill pan to allow maximum circulation of air to lift the food out of the fats and juices e Adjust the grid and grill pan runner position to allow for different thicknesses of food e Food should be thoroughly dried before grilling to minimise splashing Brush lean meats and fish lightly with a little oil or melted butter to keep them moist during cooking e Accompaniments such as tomatoes and mushrooms may be placed underneath the grid when grilling meats e When toasting bread use the shelf in position 1 with the grid in the
18. e recommend you do so for 20 minutes For recipes needing high temperatures e g bread pastries scones souffl s etc best results are achieved if the oven is preheated first For best results when cooking frozen or cooked chilled ready meals always preheat the oven first USING THE MAIN OVEN e Open the oven door e Push in the control knob and turn it to gas mark 9 After a few seconds the oven will light automatically There will only be small flames at first e Turn the control knob to the required gas mark e Wait until the oven burner is showing large flames e Close the oven door e To turn the oven off push in the control knob and turn to the off position THINGS TO NOTE e The oven light will illuminate e If there is an electrical power failure you cannot use the main oven e The cooling fan for the controls may operate after a time TO FIT THE MAIN OVEN SHELVES The shelf should be fitted with the straight rods uppermost on the frame and the forms towards the back of the oven To remove a shelf slide the shelf towards you until the shelf stop is reached Tilt shelf up at the front so that the stops clear the side supports Lift shelf clear To install a shelf reverse the above steps Each shelf position has an upper and lower support wire ensure the shelf is placed between these two support wires 11 Straight Rods Back of the Oven i HINTS AND TIPS Arrange the shelves in the requ
19. e the Grill and Oven Compartments 19 Hints and Tips 19 Cleaning the Door s 20 Replacing An Oven Light Bulb 21 Something Not Working 22 Service and Spare Parts 23 Guarantee Conditions 24 FOR THE INSTALLER Technical Details 25 Important Safety Requirements 26 Provision For Ventilation 26 Moving Your Appliance 27 For Your Safety 27 Location of Appliance 27 Levelling the Appliance 27 Connecting to the Electricity Supply 28 Connecting to Gas Supply 29 Fitting the Stability Chain 29 Testing 29 General Note 30 Notes 31 To help you the following symbols will be found in the text i Hints and Tips A Safety Instructions Please read the instruction book carefully before use and retain for future reference AT THE END OF THE APPLIANCE S LIFE The symbol Ra the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product DESCRIPTION OF THE APPLIANCE SLIP IN GAS OVEN
20. ed to the terminals in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red Ensure that the cable does not become trapped when pushing the appliance into position If a moulded plug is fitted In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to B S 1362 must be fitted Note The fuse cover must be refitted when changing the fuse In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted 28 GREEN AND CONNECTING TO GAS SUPPLY This appliance is designed to be installed with an appliance flexible connection only Supply piping should not be less than R 8 Connection is made to the Rc B S P female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance NOTE ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I E DO NOT USE P T F E SEALANT TAPE Carry out a gas tightness test after connecting to the gas supply The gas bayonet connector must be fitted in the shaded area indicated in Fig 3 Take into account that it must be possible to pull the appliance forward sufficiently
21. high position e Preheat the grill on a full setting for a few minutes before sealing steaks or toasting Adjust the heat setting and the shelf as necessary during cooking e The food should be turned over during cooking as required 10 GRILLING CHART FOOD POSITION GRILL TIME mins in total Bacon Rashers 5 6 Adjust Beefburgers 10 15 Chicken Joints grill 30 40 Chops Lamb setting 15 20 Pork 20 30 and Fish Whole Trout Mackerel grill Uaioe Fillets Plaice Cod pan eS Kebabs grid 20 30 Kidneys to A Lamb Pig Sie Liver suit Lamb Pig 1020 different Sausages 15 20 thicknesses Steaks Rare 6 12 Medium f 12 16 Well Done o 14 20 Toasted ee au Sandwiches The times quoted above are given as a guide and should be adjusted to suit personal taste THE MAIN OVEN HEAT ZONES There are zones of heat within the oven The temperature in the middle is the gas mark you have chosen The top of the oven is slightly hotter and the lower shelf slightly cooler The base of the oven is quite a lot cooler You can make use of these heat zones when you are cooking foods requiring different temperatures all at the same time If you are cooking more than one tray of similar items for example cakes or biscuits swap the trays during cooking or you can remove the top tray when the food is cooked and move the lower tray to the higher shelf to finish cooking PREHEATING When you need to preheat the oven w
22. ired positions before switching the oven on Shelf positions are counted from the top downwards Ensure that food is placed centrally on the shelf and there is sufficient room around the baking tray dish to allow for maximum circulation Do not push dishes too far back as food will burn if it overhangs the burner flame Stand dishes on a suitably sized baking tray on the shelf to prevent spillage onto the oven base and to help reduce cleaning The material and finish of the baking tray and dishes used affect base browning Enamelware dark heavy or non stick utensils increase base browning Shiny aluminium or polished steel trays reflect the heat away and give less base browning When cooking more than one dish in the oven place dishes centrally on different shelves rather than cluster several dishes on one shelf this will allow the heat to circulate freely for the best cooking results If you are cooking more than one tray of similar items for example cakes or biscuits swap the trays during cooking or you can remove the top tray when the food is cooked and move the lower tray to the higher shelf to finish cooking Do not place baking trays directly on the oven base as it interferes with the oven air circulation and can lead to base burning use the lower shelf position Do not place cookware and cooking pots with rough bases e g cast iron on the oven door as damage to the glass may occur 12 COOKING CHART
23. is the case contact the person who installed the appliance Always allow the appliance to cool before switching off at the wall prior to carrying out any cleaning maintenance work Only clean this appliance in accordance with the instructions given in this book Never use steam or high pressure steam cleaners to clean the appliance CONTENTS FOR THE USER Important Safety Information 2 Description of the Appliance 4 Getting to Know Your Appliance 5 Before Using the Appliance 6 Rating Plate 6 Preparing to Use your Appliance 6 The Cooling Fan for the Controls 6 Condensation and Steam 6 Cookware 6 Grill and Oven Furniture 6 The Hob 7 Using the Hob 7 To Light the Hob Burners 7 To Turn Off Any Burner ri Things to Note 8 Hints amp Tips 8 The Grill 9 Using the Grill 9 Things to Note 9 The Grill Pan and Handle 9 Hints and Tips 10 Grilling Chart 10 The Main Oven 11 Using the Main Oven 11 Heat Zones 11 Preheating 11 Things to Note 11 To Fit the Main Oven Shelves 11 Hints and Tips 12 Cooking Chart 13 Roasting Chart 14 Slowcook 15 Using Slowcook 15 Food Preparation 15 General Points 16 Care and Cleaning 17 Cleaning Materials 17 Cleaning the Outside of the Appliance 17 Cleaning the Control Knobs and Handles 17 Removing and Replacing the Wirework Runners 17 Cleaning the Hob 18 When Replacing Hotplate Burner Parts 18 Cleaning the Shelves Wirework Runners and Grill Oven Furniture 18 Cleaning the Grill 18 Cleaning Insid
24. iscoloration and polishing of the Stayclean surfaces may occur in time This DOES NOT affect the Stayclean properties in any way Use minimal if any extra oil or fat when roasting meat potatoes only require brushing with fat before cooking Extra fat in the oven during roasting will increase splashing and soilage It is NOT necessary to add water to a meat tin when roasting The water and the fat juices from the joint create excessive splattering during cooking even at normal temperatures as well as causing condensation Covering joints during cooking will also prevent splashing onto the interior surfaces Removing the covering for the last 20 30 minutes will allow extra browning if required Some large joints and turkeys especially benefit by this method of cooking allowing the joint to cook through before the outside is over browned 19 CLEANING THE DOOR S j To prevent damaging or weakening the door glass panels avoid the use of the following e Household detergents and bleaches e impregnated pads unsuitable for non stick saucepans Brillo Ajax pads or steel wool pads Chemical oven pads or aerosols Rust removers Bath Sink stain removers CLEANING BETWEEN THE OUTER AND INNER DOOR GLASS The outer door glass is removable for cleaning TO REMOVE THE OUTER GLASS 1 2 A TO Open the oven door to gain access to the top of the oven door To remove the top trim carefully push the trim toward
25. lon brush old toothbrush etc It is natural for the burners to emit noise as the gas is being drawn through the burner and may reduce as they heat up This is a natural occurrence when the burner is alight and does not affect the performance of the burner lt is normal for some metal parts on the cooker to produce noise when in use this is due to expansion and contraction when heating up and cooling down 22 SERVICE AND SPARE PARTS s 8viceerorce In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading Something Not Working When you contact the Service Force Centre you will need to give the following details Your name address and post code Your telephone number Clear and concise details of the fault The model and serial number of the appliance found on the rating plate The purchase date OP Ge Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls CUSTOMER CARE DEPARTMENT For general enquires
26. ly accessible wall socket Which is adjacent to but not directly above and not more than 1 7m away from the appliance and capable of electrical isolation The cooker point should be within 1 7m of the appliance to make it accessible to switch off the appliance in case of emergency The mains lead should be routed so that it cannot touch hot parts of the cooker i e the back panel above a height of 650mm from the floor Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below If the supply cord is damaged it must be replaced Please contact your local Service Force Centre If the moulded plug is cut from the cable for any reason it must be destroyed or disposed of safely as protruding wires will be an electrical shock hazard If the fitted plug is removed The flexible mains lead must be correctly connected as below to three pin plug of not less than 13amp capacity If a B S 1363 fused plug is used it must be fitted with a 3 amp fuse which is approved to B S 1362 Important The wires in the mains lead fitted to the appliance are coloured in accordance with the following code GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connect
27. n grill pan grid oven shelves and wirework runners may be cleaned using a soap impregnated steel wool pad Soaking first in hot soapy water will make cleaning easier CLEANING THE GRILL Do not clean the grill burner itself Cleaning the grill may cause the holes in the burner to become blocked preventing it from operating correctly Due to the nature of stainless steel the grill burner may tarnish through use over a period of time This is quite normal and is not a fault on the appliance Clean the area around the grill frequently using hot soapy water 18 PAN SUPPORT ELECTRODE hp ees SLOTS BODY CLEANING INSIDE THE GRILL AND OVEN COMPARTMENTS The sides and back of the main oven compartment are coated with a special Stayclean coating They should not be cleaned manually The vitreous enamel main oven base and grill compartment can be cleaned using normal oven cleaners with care Ensure that the manufacturers instructions are followed and that all parts are well rinsed afterwards Aerosol cleaners must not come into A contact with elements burners door seal or any painted finishes as this may cause damage 2 HINTS AND TIPS AN Aerosol cleaners must not be used on Stayclean surfaces To carry out the cleaning cycle remove the oven shelves and set the oven to gas mark 7 It is a good idea to run the oven for an hour or two per week to ensure continued good performance from the Stayclean finish Slight d
28. of each hotplate burner 29 580 CHECKING THE GRILL Place the grill pan containing the grid with the handle attached into the grill compartment Light the grill burner by turning the grill tap full on and pressing the ignition button on the fascia panel As soon as the burner is lit the button can be released CHECKING THE HOTPLATE Lift the lid Fit the burner crowns and caps ensuring that they are correctly seated Fit the pan supports Check each of the hotplate burners in turn by turning the hotplate tap to its full on position and pressing the ignition button As soon as the burners are lit the button can be released CHECKING LID SHUT OFF DEVICE Lift the lid 2 Turn one hotplate tap to its full on position and push the ignition button 3 Close the lid There should now be no gas supply to the hotplate and the burner will go out 4 Turn off the hotplate and lift the lid The gas supply should now be restored to the hotplate when the tap is turned on CHECKING THE MAIN OVEN 1 Turn on the oven thermostat control knob to mark 9 As soon as the burner is alight the control can be released 2 There should now be a low gas rate to the burner which is the F S D by pass rate 3 When the F S D phial has heated up it opens the F S D valve which allows the main gas supply to the oven burner 4 After 1 minute check that the flame covers the full width of the burner and is stable 5
29. ougher cuts of meat more tender Some foods such as pastry and biscuits are not suitable for slow cooking because the temperature is too low Cover all food during cooking to prevent it from drying out You can uncover food for the last half hour if it is normally served golden brown USING SLOW COOK e You need to cook food at gas mark 6 for 30 minutes before you turn the oven down to the slow cook setting This makes sure that the temperature of the food gets hot enough to start the food cooking FOOD PREPARATION SLOW COOKING JOINTS OF MEAT AND POULTRY e Do not cook meat joints over 2 7kg 6lb e Do not cook poultry over 2 kg 4lb 802 e Cook on the middle shelf of the oven or above e Cook stuffing separately e Cook for at least six hours e Only cook joints of pork if you can make sure by using a meat thermometer that the temperature inside the joint is at least 88 C e For good air circulation always stand joints on a rack in a roasting tin or casserole e Thaw all frozen meat and poultry before you cook it e Prime cuts of meat do not benefit from slow cooking e Remove excess fat and skin unless it is browned first SOUPS CASSEROLES AND STEWS e Do not cook casseroles over 2 7 kg 6lb e Bring to the boil on the hotplate then cook on slow cook e Cook on the middle shelf of the oven or above e Cover food with a tight fitting lid or tin foil 15 Vegetables e Cut into small pieces
30. red Safety may be impaired if installation is not carried out in accordance with these instructions Before connecting the appliance make sure that the voltage of your electricity supply is the same as that indicated on the rating plate This is situated on the lower front frame of the appliance and can be seen upon opening the door Alternatively the rating plate may also be found on the back or top of some models where applicable Do not alter the electrical circuitry of this appliance PROVISION FOR VENTILATION This appliance is not connected to a combustion products evacuation device It shall be installed and connected in accordance with the current installation regulations Particular attention shall be given to the relevant requirements regarding ventilation The room containing the appliance should have an air supply in accordance with BS 5440 Part 2 Current Edition All rooms require an openable window or equivalent and some rooms will require a permanent vent as well For room volumes up to 5m an air vent of 100cm is required for room volumes between 5m and 10m an air vent of 50cm is required If the room has a door that opens directly to the outside no air vent is required For room volumes that exceed 11m no air vent is required If there are other fuel burning appliances in the same room BS 5440 Part 2 Current Edition should be consulted to determine the requisite air vent requirements Prolonged inten
31. s the oven and lift off Hold the door securely in place with one hand before sliding the glass out with the other hand Clean the outer and inner glass using hot soapy water or Hob Brite cleaner may be used Do not use Hob Brite on the Stainless Steel or painted finishes Ensure that all parts are well rinsed and thoroughly dried before attempting to replace the outer door If the door glass panel becomes chipped or has deep scratches the glass will be weakened and must be replaced to prevent the possibility of the panel shattering Please contact your local Service Force Centre who will be pleased to advise further REPLACE THE OUTER GLASS To ensure the glass is properly located the text This side up should be facing towards you at the top edge of the door and facing into the cavity 1 2 Holding the glass with both hands gently slide the glass into the side trims of the oven door To replace the trim line up the clips on the underside of the trim with the connectors at the top of the door Carefully slide the trim towards the door Ensure the trim is securely in place before closing the oven door Do not attempt to use the oven without the glass being in place 20 Please note that the door glass on your product may differ in type and shape from that shown in the diagram REPLACING AN OVEN LIGHT BULB The type of bulb required is a 300 C 25 watt small Edison Screw Di
32. sconnect the appliance from the electricity supply before replacing the bulb 1 Make sure the appliance is cool before replacing the bulb 2 Open the door and remove the shelves and wirework runners 3 Remove the glass cover by turning it to the left 4 Unscrew the bulb by turning it to the left 5 Fit a new bulb and then replace the glass bulb cover 6 Refit the wirework runners and replace the oven shelves 7 Restore the electricity supply 21 SOMETHING NOT WORKING We recommend that your appliance has an annual gas safety check carried out by our approved service organisation Please carry out the following checks on your appliance before calling a Service Engineer It may be that the problem is a simple one that you can solve yourself without the expense of a service call In guarantee customers should make sure that the checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown Please note that proof of purchase is required for in guarantee service calls PROBLEM The grill and oven do not work The oven is not cooking evenly The oven light fails to illuminate The oven temperature is too high or too low The cooling fan does not work The hob burners will not light The flame colour is orange yellow The burner is not igniting or only partially lighting The burner sounds noisy The burner is emitting a popping sound Nois
33. se a round Wok with a collar support the collar must be the open wirework type otherwise the performance of the burner will be affected Take care to avoid burns and scalds when reaching across the hotplate Take extra care when deep fat frying do AN not cover the pan with a lid Do not leave a pan unattended If the pan catches fire leave it where it is and turn off all controls Place a damp cloth or a fitting lid over the pan to smother the flames Never put water on the fire Leave to cool for 30 minutes THE GRILL CAUTION Accessible parts may be hot when the grill is in use Young children should be kept away When you first operate the grill you may hear some sounds as the burner heats up this is quite normal and is not a fault on the appliance USING THE GRILL e Fully open the grill door e Push in and turn the control knob to the left to the highest setting This is shown by a large flame symbol Press the ignition button immediately e When the burner has lit release the control and ignition button adjust the setting as required The grill door must be left open when grilling The grill door is fitted with a shut off A valve This will cut off the gas when the door is closed The gas will flow again when the door is opened Always ensure that the grill control is in the off position before closing the door THINGS TO NOTE e The cooling fan for the controls may operate after a time
34. sive use of the appliance may call for additional ventilation for example opening a window or more effective ventilation for example increasing the level of mechanical ventilation where present 26 MOVING YOUR APPLIANCE You may damage some soft or badly fitted floor coverings when you move the appliance The floor covering under the appliance should be securely fixed so it does not ruck up when you move the appliance across it Alternatively you could remove the floor covering This appliance is heavy and care must be taken when moving it Do not try to move the appliance by pulling the door handles To move the appliance open the grill door Raise the appliance off its front feet by lifting it from inside the oven Pull the appliance forward When you replace the appliance push it back to the stop and make sure there is the same gap at each rear corner FOR YOUR SAFETY Do not try to disconnect the appliance from the gas supply if the supply pipe does not have a bayonet connection as described in the installation instructions If this is the case contact the person who installed the appliance LOCATION OF APPLIANCE This appliance must not be installed in a bed sitting room of volume less than 20m or in a bathroom shower room or garage It is essential that the appliance is positioned as Fig 1a Shelves wall cabinets and cooker hoods must be fitted a minimum of 750mm directly above the top of the hotplate or greater for
35. the main oven is in use It may run on after the controls are switched off until the appliance has cooled During the initial period the cooling fan may turn ON and OFF this is quite normal CONDENSATION AND STEAM When food is heated it produces steam similar to a boiling kettle The vents allow some of this steam to escape However always stand back from the appliance when opening the door s to allow any build up of steam or heat to release If the steam comes into contact with a cool surface on the outside of the appliance e g a trim it will condense and produce water droplets This is quite normal and is not caused by a fault on the appliance To prevent discolouration regularly wipe away condensation and also soilage from surfaces For your safety wall coverings at the rear of the appliance should be securely fixed to the wall COOKWARE Main oven Do not use baking trays larger than 30cm x 30cm 12 x 12 as they will restrict the circulation of heat and may affect performance GRILL AND OVEN FURNITURE The following items of grill and oven furniture have been supplied with the appliance If you require replacements of any of the items listed below please contact your local Service Force Centre quoting the relevant part number 1 grill pan 349099801 1 grill pan handle 349100501 1 grill pan grid 311757500 1 cranked shelf for grilling 2 cranked shelves for main oven cooking THE HOB US
36. unted from the top of the oven downwards To help pastry dishes brown on the underside cook on a metal plate or place on a baking tray 13 ROASTING CHART Gas Mark COOKING TIME 25 35 minutes per kg 11b and 25 35 minutes over 25 35 minutes per kg 11b and 25 35 minutes over 30 40 minutes per kg 11b and 30 40 minutes over 20 25 minutes per kg 11b and 20 minutes over 20 25 minutes per kg 11b up to 312kg 7lb then 10 minutes per Y2kg 1lb over 312kg 71b 25 35 minutes per kg 11b and 25 30 minutes over 35 40 minutes per kg 11b and 35 40 minutes over INTERNAL TEMPERATURES Rare 50 60 C Medium 60 70 C Well done 70 80 C MEAT Beef Beef boned 5 Mutton Lamb 5 Pork Veal Ham 5 Chicken 5 Turkey Goose 5 Duck 5 Pheasant 5 Rabbit 5 20 minutes per kg 11b and 20 minutes over The roasting temperatures and times given in the chart should be adequate for most joints but slight adjustments may be required to allow for personal requirements and the shape and texture of the meat However lower temperatures and longer cooking times are recommended for less tender cuts or larger joints Wrap joints in foil if preferred for extra browning uncover for the last 20 30 min cooking time 14 SLOW COOK The slow cook setting gives a very low heat in the oven It is particularly useful when you are cooking soups stews and casseroles because the long slow cooking will make cheaper t
37. w again when the lid is opened If you close the lid of the appliance while TO TURN OFF ANY BURNER 1 Turn the control knob to the off position When lighting any burner ensure that it A is lit before you leave the appliance When turning off a burner ensure the flame has gone out before leaving the appliance In the event of the burner flames being N accidentally extinguished turn off the burner control and do not attempt to re ignite the burner for at least 1 min THINGS TO NOTE If you are having any difficulty lighting a hob burner turn all the hob controls off and make sure the burner parts have been replaced correctly i HINTS AND TIPS e Do not overfill pans or they will boil over e Do not use pans with very heavy handles which cause the pan to tip e Do not close the lid until the appliance has cooled down Do not use the lid as a work surface or chopping board This could damage the glass and reduce its strength Place pans on the centre of the burners A Position pans so the handles cannot be accidentally knocked or overhang the appliance Lift pans on and off the pan supports Do not slide them across the hob e Do not leave accidental spillage on the hob or removable parts The spillage should be wiped up and the parts washed and carefully dried as soon as the hob pan supports and burner parts are cool enough to touch e A flat based Wok will stand stable on the pan supports If you u
Download Pdf Manuals
Related Search