Electrolux EGG 689 User's Manual
Contents
1. 11 Ignition System Gas Ignition 12 Ignitor does not spark NO Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Check continuity from N on the mains connector block on the ignitor unit Check continuity from L on the mains connector block and the taps ignition switches Check continuity from ignition switches connector to ignitor unit YES Check continuity from the tip of each electrode to the terminals 1 to 4 on the ignitor unit Check for breaks in the insulation of the HT leads Change the taps ignition switches Change the ignitor unit Check gas supply at burner Light burner manually Check by pass simmer adjusted Check position of the electrode Check fitting of burners Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting To do this follow the procedure below Turn the gas tap to the MAX position and ignite Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times If the flame is unstable or is extinguished follow the procedure below Procedure S Re ignite the burner and set to MIN Remove the control knob To adjust use a thin bladed screwdriver and turn the adjustment screw see diagram until the flame Minimum adjustment screw is steady and does not extinguish2. EZA Bs anonn Dimensions are given in mm FO 2108 4 a Sealing gasket Electrical connections A Any electrical work required to install this hob should be carried out by a qualified electrician or competent person in accordance with the current A regulations THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should these safety measures not be observed This hob is designed to be connected to a 230 240V 50Hz AC electrical supply Before switching on make sure the electricity supply voltage is the same as that indicated on the hob rating plate The rating plate is located on the bottom of the hob A copy is attached on the back cover of this book The hob is supplied with a 3 core flexible supply cord incorporating 3amp plug fitted In the event of having to change the fuse 3amp ASTA approved BS 1362 fuse must be used Should the plug need to be replaced for any reason the wires in the mains lead are coloured in accordance with the following code Green Yellow Earth Blue Neutral Brown Live e Connect the green and yellow earth wire to the terminal in the plug which is marked with the letter or the earth symbol or coloured green and yellow Connect the blue neutral wire to the terminal the plug which is marked with the letter N or coloured black Connect the b
3. The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world 02 03 Grafiche MDM Forli
4. when the knob is turned from MIN to MAX Repeat this procedure for all burners Pressure Testing Ee Remove left hand pan support and front left burner cap and crown Fit manometer tube over the injector Turn on the burner gas supply and ignite another burner The pressure reading should be nominally 20mbar and must be between 17 mbar and 25mbar Turn off the burner supplies 13 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted The gas rate is adjusted to suit Method Ensure that the gas taps are the OFF position e Isolate the hob from the electrical supply e Remove all pan supports burner caps rings crowns and control knobs With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors 14 To adjust the gas rate With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment screw Upon completion affix the replacement rating plate on the under side of the hob IMPORTANT The replacement conversion of the gas hob should only be undertaken by a competent person CUSTOMER CARE Electrolux 55 77 High Street Slough Berkshire SL1 104 Tel 08705 950950 Electrolux 2003 The Electrolux Group The world s No 1 choice
5. Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m If it is installed in a room of volume less than 5 an air vent of effective area of 110 cm is required If it is installed in a room of volume between 5 and 10 an air vent of effective area of 50 cm is required while if the volume exceeds 11 no air vent is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 11 m If there are other fuel burning appliances in the same room B S 5440 Part 2 Current Edition should be consulted to determine the requisite air vent requirements Location FITTING THE GAS HOB The hob may be located in a kitchen a kitchen diner or bed sitting room but not in a bathroom shower room garage Before making the cut out in the worktop ensure that the edges of the hob that are to be near either a side or rear wall have a minimum distance of 55 mm between the edge of the hob and the wall The minimum distance combustible material can be fitted above the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob The minimum distance combustible material can be fitted directly above the hob is 700 mm Aminimum distance of 100 mm must be left between the side edges of the hob and any adjacent cabinets or walls Installati
6. Gas hob INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance Mod EGG 689 35678 9001 HX Electrolux ce A Important Safety Information Installation This hob must be installed by qualified personnel according to the manufacturer s instructions and to the relevant British Standards Any gas installation must be carried out by a registered CORGI installer Remove all packaging before using the hob Ensure that the gas and electrical supply complies with the type stated on the rating plate located near the gas supply pipe Do not attempt to modify the hob in any way Child Safety This hob is designed to be operated by adults Do not allow children to play near or with the hob The hob gets hot when it is in use Children should be kept away until it has cooled Children can also injure themselves by pulling pans or pots off the hob During Use This hob is intended for domestic cooking only It is not designed for commercial or industrial purposes When in use a gas cooking appliance will produce heat and moisture in the room in which it has been installed Ensure there is a continuous air supply keeping air vents in good condition or installing a cooker hood with a venting hose When using the hob for a long period of time the ventilation should be improved by opening a window or increasing the extractor speed Do not use this hob if it is in contact with water Do not
7. O FORCE Inthe event of your appliance requiring service or if you wish to purchase spare parts please contact your local Electrolux Service Force Centre by telephoning 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading Something Not Working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rating plate 5 The purchase date Customer Care Department For general enquiries concerning your Electrolux appliance or for further information on Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www electrolux co uk Customer Care Department ELECTROLUX 55 77 High Street Slough Berkshire 811 104 Tel 08705 950950 calls to this number may be recorded for training purposes Guarantee Conditions Electrolux Guarantee conditions We Electrolux undertake that if within 12 months of the date of the purchase this Electrolux a
8. YA 120 Spark Gap Fixed Cut out dimensions sods oe Semi rapid Burner Width 550 mm Heat Input 1 9 kW 6483 BTU HR Depth 470 mm Rapid Burner Supply connections Heat Input 2 9 kW Natural Gas 9895 BTU HR 2 7 kW L P G 9212 BTU HR Gas R 1 2 inch 1 2 inch male Rear right hand corner Auxiliary Burner _ Heat Input 1 0 kW 3412 BTU HR Electric 230 240V 50Hz supply 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse RAPID SEMI RAPID AUXILIARY large medium small GAS TYPE OF POSITION MAX MIN MIN MIN NOMINAL THERMAL POWER kW 37 78 MJ m Ws 50 7 NOMINAL FLOW RATE 20 mbar n lt a a 2 VALUE NOZZLE REFERENCE 1 100 mm NOMINAL THERMAL POWER kW NOMINAL FLOW gh LPG GAS 28 30 37 mbar NOZZLE REFERENCE 1 100mm VALUE 49 92 MJ Kg Burner Dia Tap By pass APPLIANCE CLASS 3 1 100 mm APPLIANCE CATEGORY 112 3 Auxiliary Semi rapid APPLIANCE GAS SUPPLY Natural gas G20 20mbar Rapid Aeration adjustment none Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and eae Use Regulations Current Edition and the IEE Wiring Regulations Current HOUT A COOKER HOOD ABOVE Edition Detailed recommendations are contained in the following British Standards Codes Of Practice B S 6172 B S 5440 Part 2 and B S 6891
9. YES Carry out Electricity supply cheek D Resistance to should now be Earth check satisfactory Has inlet fuse blown NO YES Inlet wiring faulty Rectify any fault Isolate appliance and carry out B Insulation check Rectify any fault including replacing fuses as necessary A EARTH CONTINUITY CHECK Appliance must be electrically disconnected meter set on Ohms x 1 scale and adjust zero if necessary a Testleads from any appliance earth point to earth pin on plug Resistance should be less than 0 1 Q Ohm check all earth wires for continuity and all contacts are clean and tight B INSULATION CHECK Appliance electrically disconnected all switches ON a meter set on Ohms x 1 scale Test leads from Lto N in appliance terminal block If meter reads 0 then there is a short circuit b meter set on Q Ohm x 100 scale Repeat test with leads from L to E If meter reads less than infinity there is a fault NOTE Should it be found that the fuse has failed but no fault is indicated a detailed continuity check i e by disconnecting and checking each component is required to trace the faulty component It is possible that a fault could occur as a result of local burning arcing but no fault could be found under test However a detailed visual inspection should reveal evidence of burning around the fault
10. ation This appliance complies with the following E E C Directives 73 23 90 683 Low VoltageDirective 93 68 General Directives 89 336 Electromagnetical Compatibility Directive 90 396 Gas Appliances and subsequent modifications Contents For the User For the Installer Important Safety Information Instructions for the Installer Description of the Hob Important safety requirements Operation Installation Maintenance and Cleaning Building In Something Not Working Electrical connections Service and Spare Parts Wiring Diagram oan KR W DN Guarantee Conditions Fault Finding Commissioning Conversion from Natural Gas to LPG Description of the Hob 1 Hob top 2 Rapid Burner 3 Semi rapid Burner 4 Auxiliary Burner 5 Control knobs Operation Hob burners c To light a burner e push in the relevant control and turn it to maximum position e then adjust the flame as required If the burner does not ignite turn the control knob to zero and try again If you use a saucepan which is smaller than the A recommended size the flame will spread beyond the bottom of the vessel causing the handle to overheat Take care when frying food in hot oil or fat as the overheated splashes could easily ignite As soon as a liquid starts boiling turn down the flame so that it will barely keep the liquid simmering To ensure maximum burner efficiency you should only use pots a
11. ding In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit in order to avoid any contact with the bottom of the hob which can be heated when it is operated The recommended solution is shown in diagram 3 The panel fitted under the hob should be easily removable to allow easy access if technical assistance is needed The space behind the kitchen unit b can be used for connections Fitting the hob to the worktop Before fitting the hob into the cut out an adhesive seal must be fitted to the underside outside edge diagram 4 of the hob It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below 1 Remove the pan supports the burners caps and crowns and turn the hob upside down taking care the ignition candles are not damaged in this operation Place the sealing gasket all around the glass top edge as shown in diagram 4 Fit the hob in the cut out and push it down until the glass top and the working top make contact as shown in diagram 5 2 3 ON OFF SWITCH
12. ements Products of Electrolux manufacture which are not marketed by Electrolux European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products This guarantee relates to you and cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 20 13 Germany N rnberg 49 0 800 234 7378 Italy Pordenone 39 0 800 117511 Sweden Stockholm 46 0 20 78 77 50 UK Slough 44 0 1753 219898 Instructions for the Installer Engineers technical data Overall dimensions Ignition HT Spark Width 580 mm Spark Generator Ispra Control s BF 50046 Depth 510 mm 230 240V 0 6
13. nd pans with a flat bottom fitting the size of the burner used see table maximum diameter minimum diameter Large rapid Medium Small auxiliary If the control knobs become difficult to turn please contact your local Electrolux Service Centre Maintenance and Cleaning Before any maintenance or cleaning can be carried out you must DISCONNECT the hob from the electricity supply The hob is best cleaned whilst it is still warm as spillage can be removed more easily than if it is left to cool The Hob Top Regularly wipe overthe hobtop and the aluminium frame using a soft cloth well wrung out in warm water to which a little washing up liquid has been added Avoid the use of the following household detergent and bleaches impregnated pads unsuitable for non stick saucepans steel wool pads bath sink stain removers Should the hob top become heavily soiled it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used Pan Supports The pan supports are dishwasher proof If washing them by hand take care when drying them as the enamelling process occasionally leaves rough edges If necessary remove stubborn stains using a paste cleaner Never use steel wool pads or acids The Burners The burner caps and crowns can be removed for cleaning Wash the burner caps and crowns using hot soapy water and remove marks with a mild paste cleaner A well mois
14. on IMPORTANT WHEN THE HOB IS FIRST INSTALLED This hob must be installed by qualified personnel to the relevant British Standards Once the hob nas Dem iristallod itis important to remove any protective materials which were Any gas installation must be carried out by a put on in the factory registered CORGI installer The manufacturer will not accept liability should On the end of the shaft which includes the G 1 2 the above instructions or any of the other safety threaded elbow adjustment is fixed so that the washer instructions incorporated in this book be is fitted between the components as shown in the ignored diagram Screw the parts together without using excessive force Gas Connection Connection to the gas supply should be with either rigid or semi rigid pipe i e steel or copper The connection should be suitable for connecting to R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation Ensure that the main connection pipe does not exert any strain on the hob FO 0814 It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Failure to ensure the correct assembly will cause leakage of gas A End of shaft with nut B Washer C Elbow Cut Out Size The dimensions of the cut out are given in the diagram Buil
15. operate the hob with wet hands Ensure the control knobs are in the OFF position when not in use When using other electrical appliances ensure the cable does not come into contact with the hot surfaces of the cooking appliance Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage Never leave the hob unattended when cooking with oil and fats Never use plastic or aluminium foil dishes on the hob Perishable food plastic items and areosols may be affected by heat and should not be stored above or below the hob unit You MUST read these warnings carefully before installing or using the hob If you need assistance contact our Customer Care Department on 08705 950950 Service e This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used Environmental Information e After installation please dispose of the packaging with due regard to safety and the environment e When disposing of an old appliance make it unusable by cutting off the cable Keep this instruction book for future reference and ensure it is passed on to any new owner Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions Safety Instructions Step by step instructions for an operation i Hints and Tips Enviromental inform
16. ppliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate The appliance has been used for normal domestic purpose only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by a Electrolux Service Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliance outside the United Kingdom Appliances found to be in use within a commercial or similar environment plus those which are the subject to rental agre
17. rown live wire to the terminal in the plug which is marked with the letter L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely 10 Permanent Connection In the case of a permanent connection it is necessary that you install a double pole switch between the hob and the electricity supply mains with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations The switch must not break the yellow and green earth cable at any point Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg Supply cable replacement The cable used to connect the hob to the electrical supply must comply to the specifications given below Min size Cable flex Cable type Fuse GREEN amp YELLOW 3 AMP FUSE CORD CLAMP Wiring Diagram N Fault Finding Preliminary Electrical Systems Check A IGNITOR SWITCH B IGNITOR UNIT PLUG with cover SOCKET removed face view L Earth Wire Green Yellow START Isolate appliance Je and carry out A Earth Continuity Neutral Wire check Blue CN aL NO
18. tened soap impregnated steel wool pad can be used with caution if the marks are particularly difficult to remove After cleaning be sure to wipe dry with a soft cloth 4 Something Not Working If the hob is not working correctly please carry out the following checks before contacting your local Service Force Centre IMPORTANT If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is under guarantee SYMPTOM SOLUTION E There is no spark when lighting the gas Check that the unit is plugged and the electrical supply is switched on Check that the RCCB has not tripped if fitted Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly e g after cleaning E The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles Check the burner cap and crown have been replaced correctly e g after cleaning If after all these checks your hob still does not operate In guarantee customers should ensure that the correctly contact your local Service Force Centre above checks have been made as the engineer will make a charge if the fault is not a mechanical or Please note that it will be necessary to provide proof of electrical breakdown purchase for any in guarantee service calls Service and Spare Parts SERVICE
Download Pdf Manuals
Related Search