Dynex 58" Tripod - Black Quick Setup Guide
Contents
1. 3 To pan turn the pan locking knob counter clockwise pan the tripod head then tighten to lock in place or continue panning Note For maximum stability always make sure that your camera lens is over a leg2. Storing your tripod 1 Remove your camera J 2 Lower the center column D Y N E eee 3 Push on any leg to close the tripod z 4 Collapse the legs a _ 5 Store the tripod in the carrying case Important safety instructions DX TRP58BL Make sure that all leg locks are correctly tightened and that the wrs legs are fully opened before use 58 Lightweight Tripod Do not carry or transport your tripod with camera equipment attached for example over your shoulder or cradled in your arms Do not expose your tripod to excessive heat or cold or use near any flame or fire Donot oil or grease any part of the tripod Do not use any solvents or thinners to clean your tripod Use only a mild detergent and wipe dry with a soft lint free cloth Do not exceed the load limit of this tripod Specifications Folded length 22 1 in 56 cm Maximum height 58 in 147 3 cm Minimum height 21 3 in 54 cm Weight 2 2 Ibs 1 kg Load capacity 8 8 Ibs 4 kg One year limited warranty Visit www dynexproducts com for details Contact Dynex For customer service call 800 305 2204 U S and Canada or 01 800 926 3020 Mexico www dynexproducts com DYNEX is a registered trademark of BBY Solutions Inc Registered in some countries Distributed by Best Buy Purchasing LLC 7601 Penn Ave South Richfield MN 55423 U S A 2014 BBY Solutions Inc All Rights Reserved Before using your new pr
3. oduct please read these instructions to prevent any damage V1 ENGLISH 14 0369 QUICK SETUP GUIDE Package contents Tripod Carrying case e Quick Setup Guide Features fe nem di Desernton id Quick release plate Mount your camera to this plate then mount this plate to the tripod 2 Leveling bubble The quick release plate is level when the bubble is within the circle 3 Pan locking knob Locks the tripod head so that it will not rotate horizontally Elevation locking knob Locks the center column in place a Elevation crank Raises and Raises and lowers the center column the center column Quick release plate Secures Pe E quick release plate to the locking lever tripod 7 Vertical tilt lock knob Adjusts the vertical tilt up to 90 degrees Horizontal tilt lock Adjusts the horizontal tilt handle ka Grip sponge Grip the tripod comfortably Locking collar Locks the tripod legs in place to provide maximum stability and strength Flip lever leg locks Lift to adjust leg height then close to lock 12 Rubber feet Provide a secure non slip footing for your tripod Setting up your tripod 1 Open the flip lever leg locks on each leg Extend the leg sections from the top down thickest section first to reach the height you want Note Adjusting the thickest leg sections first gives your tripod more stability and support 2 Close the flip lever leg locks to lock each leg at the desired length Cauti
4. on Securing a leg lock incorrectly can cause a leg to retract unexpectedly and could result in damage to the tripod or equipment mounted on the tripod 3 Loosen the locking collar on the center column then spread the legs to the preset angle Set the tripod on a firm surface Tighten the locking collar to stabilize your tripod 4 Adjust the height of the center column by loosening the elevation locking knob turning the elevation crank until the center column is at the height you want then tightening the knob Turn the locking knob clockwise to lock the center column in place Leg lock Center column Elevation locking knob Elevation crank 5 Hold the quick release plate locking lever open then lift the mounting plate to remove it Mounting plate Locking lever 6 Align the bottom of your camera or camcorder with the 1 4 mounting screw and indexing pin if necessary on the plate then secure your camera or camcorder to the plate with the screw The screw should be tight The indexing pin retracts if it is not required 7 Open the plate locking lever and slide the plate onto the tripod head Push the lever until it stops to secure the plate Using your tripod 1 To adjust vertical tilt loosen the vertical tilt lock knob rotate the plate up to 90 degrees then tighten the knob 2 To adjust horizontal tilt turn the horizontal tilt lock handle counter clockwise tilt the tripod head then tighten the handle
Download Pdf Manuals
Related Search