Dorel Car Seat Eng. 4358-5936 User's Manual
Contents
1. systems in your vehicle If you need a locking clip please go back to the store where you purchased this child restraint and purchase one or call us at 1 800 544 1108 to order one Locking clips from any child restraint manufacturer are okay to use NOTE You do not need a locking clip when using this seat as a belt positioning booster even with older vehicles Remove the locking clip when the vehicle seat belt is not being used with the child restraint A locking clip will not fix all types of seat belt problems Before you put your child restraint in the vehicle buckle the lap shoulder belt Pull on the lap belt portion If it loosens or slips you must either use a locking clip to hold the seat belt tight or move the child restraint to another seating location Thread both vehicle lap and shoulder belts through the slot as shown and out other side Buckle Pull up on shoulder belt until all slack is out and lap belt is tight Grasp both vehicle belts together just behind the buckle plate and unbuckle NOTE If the buckle plate ends up behind the child restraint grasp the belts to the outside of the child restraint as close to the buckle plate as possible continued on next page Thread both portions of 7 the vehicle belt onto the Trouble Shooting locking clip If your child restraint is not held securely by the belt Press down firmly on the child restraint and remove all the slack in the belt Make sur2. and properly or where it can be loosened by pulling on it can result in serious injury or death Check vehicle instructions for more information about air bag child restraint use 21 Forward Facing Installation with Vehicle Belts Connect and tighten harness straps prior to installing in vehicle Place child restraint flush against the back of the vehicle seat forward facing in the back seat Thread the vehicle lap belt or lap shoulder belt combination through the belt path and out other side Buckle Place one knee in the child restraint and push down firmly while pulling up on belt to tighten For a manual belt refer to Knowing your Vehicle Belt section With knee still in child restraint attach hook to anchor in vehicle Push down firmly and tighten top anchorage strap To adjust top anchorage strap See Adjusting Top Anchorage Strap section NOTE If your vehicle does not have an anchor bracket tuck the top anchorage strap s hook under the child restraint 33 With weakest hand at belt path tilt and push the child restraint forward and back and from side to side If the seat belts do not loosen your child restraint should be secure NOTE Some play from front to back or about an inch from side to side is acceptable If it moves more review Knowing Your Vehicle Belts and The Locking Clip sections AWARNING Using this child r
3. child restraint should be placed in the vehicle and which restraint should be used 22 40 Ibs 10 1 18 kg 34 43 in 85 1 110 cm and Over Year Old Forward Facing using 5 point harness Child and child restraint face the front of the vehicle and are placed in the back seat 40 80 Ibs 18 1 36 3 kg 43 52 in 110 1 132 1 cm and Over Year Old Belt Positioning Booster using vehicle lap shoulder belt combination Child and child restraint face the front of the vehicle and are placed in the back seat 5 point harness is removed Preparing Child Restraint to Fit You MUST make these Your Child adjustments with your child before you install the child restraint in the vehicle yA gt a NY Make sure LATCH belt packaging is pulled free of child restraint shell Loosen harness by pushing down on the harness release lever under flap on the front of child restraint while pulling out on the harness Press on harness retainer release button and pull apart Press red button on buckle to release the buckle plates Place harness over sides of child restraint continued on next page Pull harness through the harness guides from the front Place the child s bottom and back flat against the child restraint This will increase comfort and allow the harness to properly tighten Rethread harness into new harness guide location Refasten harness to splitter plate Make sur
4. injury harness retainer 5 Do the same to the other harness end Make sure l Remove harness as the harness is not twisted described in the Belt Positioning Booster Push harness ends through f section upper slots in shell 6 If your child restraint has armrests pull armrest covers off armrests and pull through hole in back of shell Fit loops on harness ends onto the splitter plate id wi PRE From underneath bottom of shell release the elastic straps shown in red AWARNING Failure to reattach the harness correctly can result in serious injury or death a I 34 35 continued on next page Remove the 6 harness guides shown in red by pushing down on one edge with one hand and pulling out from the front side with the other Pull pad off shell Clean with warm sudsy water rinse clean and air dry Do not use bleach or other harsh cleaners Replace seat pad by reversing order lay pad on shell replace all harness guides turn shell over to expose the back rehook elastic straps and replace armrest covers Rethread harness see belt positioning booster section 36 Locking Clip You will rarely need to use a locking cli except for in some older vehicles Built in child restraint locking systems have been required in vehicles since 1996 and many vehicles had these features even earlier Check your vehicle owner s manual to learn how to use the
5. the child restraint Try moving the child restraint toward the center of vehicle or move the vehicle seat forward or back Check to see if your vehicle has adjustable shoulder belt anchor points Do Not place the shoulder belt behind the child 38 39 Warranty Dorel Juvenile Group Inc DJG warrants this product to the original retail purchaser as follows This product is warranted against defective materials or workmanship for one year from the date of original purchase An original receipt is required to validate your warranty DJG will at its option provide replacement parts or replace this product DJG reserves the right to substitute if the part or model has been discontinued To make a claim under this warranty you may contact us at www djgusa com fax us at 1 800 207 8182 24 hours a day write to DJG Consumer Relations Department P O Box 2609 Columbus IN 47202 2609 or call 1 800 544 1108 from 7 00 a m to 6 00 p m EST Monday through Thursday and from 7 00 a m to 4 30 p m on Friday Proof of purchase is required and shipping charges are the responsibility of the consumer Warranty Limitations This warranty does not include damages which arise from misuse or abuse of this product Limitation of Damages The warranty and remedies as set forth are exclusive and in lieu of all others oral or written expressed or implied In no event will DJG or the dealer selling this product be liable to you for any damages includ
6. Replacement Parts List NOTE If requested color is not available similar color will be substituted Part Cost Quantity Total Cost Crotch Strap Buckle 5 99 X Harness Strap 2 99 X Seat Pad owe 29 99 X Harness Retainer 1 50 X Locking Clip 2 50 X Top Anchorage Tether eee oD 9 99 X Latch Kit se i X Cup Holder 3 50 X Instructions 0 0 00 X Merchandise Total Shipping and handling 150 01 to 200 00 11 95 200 01 and Upsss 13 95 Up to 25 00 iniciis 25 01 to 50 00 50 01 to 75 00 75 01 to 100 00 100 01 to 150 00 10 95 Sales Tax Indiana California Arkansas and Massachusetts residents add applicable sales tax Grand Total No shipping and handling on instruction manuals on quantities of 6 or less Add 50 for each instruction manual over 6 then add applicable shipping and handling No shipping and handling on instructions for quantities under 6 Add 50 for each instruction over 6 then add applicable shipping and handling Outside Continental USA 10 00 Fill Out For Credit Card UVisa UMastercard Card Exp Date Cardholder s Name Card Number Signature eoeevwewceoeeoeeceoee eee ee ec o INITGALLOG NO LNDe cece ee coo cooo ooooooooo Eng 4358 5936 Commuter Ventura High Back Booster Instruction Manua
7. ake sure buckle is locked tightly Snap the harness retainer together Failure to fasten and tighten the harness system correctly with each use can result in serious injury or death Removing Your Child From the Child Restraint wey Loosen harness by pushing 1 gt A down on the harness iz release lever while pulling ES out on the harness NOOO Press on release button and pull apart Press red button on buckle to release the buckle plates Place harness over sides of child restraint Remove child VAJ Be Choosing LATCH or Vehicle Belts The LATCH System ces cE 3 Vehicle Belts LATCH means Lower Anchors and Tethers for CHildren Not all vehicles manufactured before September 2002 were equipped with LATCH The LATCH system allows a child restraint to be secured in the vehicle without using the vehicle belt system and can ONLY be used in vehicles that have the anchor bars installed Check your vehicle owners manual to see which seating positions may be equipped with the LATCH system If LATCH is not an option you will use your vehicle s belts In most cases you will use the lap shoulder belt combination There are some vehicle belts that will not work with a child restraint or will require special attention See next page for specific instructions Knowing Your Vehicle Belts Not all vehicle belts will work with this child restraint You must deter
8. d on next page aBe yo ueak 42AE WO 01 1 1 S8 Ebre 8H 81 101 S41 OF Z7Z 9SN Bupe4 puemio4 With weakest hand at belt path tilt and push the child restraint forward and back and from side to side If the LATCH belts do not loosen your child restraint should be secure NOTE Some play from front to back or about an inch from side to side is acceptable If the child restraint does not remain tight do not use the child restraint in this seating location with this LATCH system LATCH hooks MUST be securely fastened Failure to do this can result in serious injury or death After checking for hot seat and buckles place your child in the child restraint as described in the Securing Your Child in the Child Restraint section To release LATCH Press down firmly on adjuster side of child restraint and press release button on adjuster to release tension Unhook LATCH hooks 26 Adjusting the Top Anchorage Strap The top anchorage strap is used for the forward facing position only Most vehicles made after 9 1 99 already have the anchor hardware for a top anchorage strap Refer to your owner s manual or call your dealer Storage of Top Anchorage Strap Belt Positioning Booster position Place top anchorage strap and anchor hook under the child restraint See pictures below and on next page to determine which top anchorage strap model you have Follow a
9. e harness does not twist Check Harness Height Forward Facing Position Harness guide fea must be even with or AWARNING uide j R EE Failure to reattach the harness correctly If the top harness guides can result in serious injury or death are below the child s shoulders the child weighs at least 40 Ibs 18 1 kg and is over year old convert the seat to a belt positioning booster Pull pad off corner Hook bottom of cup holder on bottom edge of child restraint and rotate cup Determine which set holder up of harness guide slots works best for your child Adjust if needed Snap top of cup holder on top edge of child restraint Make certain cup holder is flush on the top and sides of child restraint Replace pad To change harness location From the back of the seat remove harness from splitter plate Pull on harness adjustment strap to tighten harness snugly Securing Your Child in the Child Restraint NOTE A snug strap should not allow any slack It lies in a relatively straight line without sagging It does not press on the child s flesh or push the child s body into an unnatural position Position harness straps over the child s shoulders Position the harness Push each buckle plate into buckle until you hear a click Remember to retainer at mid chest even with arm pits away from the child s neck always pull up on harness straps to m
10. e the belt buckle is not up against the child restraint where the belt cannot be tightened Review Locking Clip section and Top Anchorage Strap Section If you cannot secure the child restraint tightly move it to another seating location 2 If the child restraint buckle or harness ue release lever sticks or you cannot get the Position locking clip about straps tight enough around child I in 2 5 cm from vehicle DO NOT LUBRICATE Check around buckle and harness belt s buckle plate release lever for dropped food sticky spilled drinks dirt leaves etc Clean with warm water and or remove object with tweezers If you cannot get the harness to adjust and remain tight with the buckle securely locked do not use the child restraint 3 If your harness twists or ropes Straighten the harness each time you put your child in the seat to help prevent twisting Lock the buckle and tighten harness and it will be ready for next use 4 In belt positioning mode if your child restraint is not held securely by the vehicle Rebuckle belt Lap belt belt portion should now be Remove all the slack in the vehicle belt Make sure the tight If not remove belt buckle is not up against the child restraint where the locking clip and repeat all belt cannot be tightened If you cannot secure the child steps restraint tightly move it to another seating location 5 In belt positioning mode if the shoulder belt crosses the child s neck when using
11. ent strap as far out as possible Pull harness through the slots from the front Unthread harness from the harness retainer Unthread harness from the buckle plates Pull harness out of shell continued on next page ade jo ueak JAAC WP ZEI 1OI 1 ZS Ev 31 9E 1 81 S41 O8 OF 2SN 919009 BulUONISog 3Jag From bottom of seat locate buckle s metal clip Belt Positioning Booster Installation Place child restraint against the back of the vehicle seat NOTE Tuck the top anchorage strap and hook under the child restraint Place the child s bottom and back flat against the child restraint Insert metal clip up through the shell and pad From the front pull buckle free from shell and pad Lock buckle plates into buckle for future use Place lap belt across child s thighs Lock buckle NOTE If your child restraint has armrests make sure the lap and shoulder belt are placed under armrest as shown AWARNING Use only the vehicle s lap and shoulder ase yo weak J AO W ZEI 1O11 ZS Ep 31 9E 1 81 S41 O8 OF 2SN 423SC0g Sujuonisod 499 belt system when restraining the child in this booster seat Failure to do this can result in serious injury or death 30 31 continued on next page Secure the shoulder belt through one of the notches in the shoulder belt guide The belt should cross the base of the child s neck and across
12. estraint in any vehicle seat where the lap belt cannot be sider securely and properly or where it can be loosened by pulling on it can result in serious injury or death 23 After checking for hot seat and buckles place your child in the child restraint as described in the Securing Your Child in the Child Restraint section ase yo ueak 42AO WO 0 1 1 S8 EP HE 81 81 101 SAI Ob ZZ 2SN Bulde4 PaeM4o4 NOTE Do not use LATCH system along with the adult lap or lap shoulder belt Route LATCH belt through upper slot in side of shell Pull one LATCH hook across the back and out the other side The LATCH adjuster can be on either side but the belt should not be twisted Connect and tighten harness straps prior to installing in vehicle Place child restraint flush against the back of the vehicle seat forward facing in the back seat 25 Fasten one LATCH belt hook to the anchor in the vehicle seat located in the vehicle seat bight Repeat for other side of child restraint See your vehicle owner s manual for locations and more information Place one knee in the child restraint and push down firmly while pulling up on the loop to tighten belt With knee still in child restraint attach hook to anchor in vehicle Push down firmly and tighten top anchorage strap To adjust top anchorage strap See Adjusting Top Anchorage Strap section continue
13. ified for aircraft use only when used with the internal harness Do not use as a belt positioning seat because aircraft seats do not have shoulder belts Use on forward facing aircraft seats only and in a position where the lap belt can be tightened securely This child restraint is installed in an aircraft seat the same way it is installed in the vehicle Use the child restraint only with F A A certified equipment Contact the airline prior to taking a child restraint on board in order to comply with their specific regulations 5 Understanding Your Vehicle Your vehicle s features may be considerably different than those pictured here Consult your vehicle owner s manual to help identify your vehicle s specific features A Anchor Bracket For Top Anchorage Strap Forward Facing Only B LATCH Anchors In seat bight C Seat Buckles D Air Bag Consult your vehicle owner s manual for all air bag locations E Seat Bight Where seat cushions meet Child Restraint Parts Pillow Buckle Plates Top Anchorage M LATCH Belt on select models Buckle Tether Strap amp may be between Shoulder Belt H Rel Mook pad and shell Guide rmarness Melee Instructions Lever Shell e Harness Retainer 4 Cup Holder Splitter Plate on select models Armrests on select models Harness Adjustment Strap Choosing Restraint and Position Your child s height weight and age determine how your
14. ing incidental or consequential damages arising out of the use or inability to use this product Limitation of warranties and other warranty terms and state law rights Any implied warranties including implied warranties of the merchantability and fitness for a particular purpose shall be limited to the duration and terms of the express written warranty Some states do not allow limitations as to how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state Neither DJG nor the dealer selling this product authorized any person to create for it any other warranty obligation or liability in connection with this product PLEASE COMPLETE AND MAIL THE PRE ADDRESSED OWNER REGISTRATION CARD WITHIN 30 DAYS OF PURCHASE TO EXPEDITE WARRANTY CLAIMS AND TO VERIFY THE ORIGINAL DATE OF PURCHASE 40 Replacement Parts Order Form Complete the form below Your model number with color code and manufacture date code MUST be included on the form to ensure proper replacement parts Your model number with color code and the date code can be found on a sticker on the side of child restraint Payment in U S dollars must accompany your order Choose parts needed from the list on the next page Return the form with payment to Dorel Juvenile Group Inc Consume
15. l www djgusa com This child restraint is designed for use by children whose Weight 22 80 pounds 10 1 36 3 kg Height 34 52 inches 85 1 132 1 cm Read all instructions BEFORE USING this child restraint KEEP INSTRUCTIONS FOR FUTURE USE AIMPORTANT Failure to follow the warnings on the labels and in the instruction manual can result in the death or serious injury of your child Before You Begin Thank you for choosing this car seat referred to throughout this manual as a child restraint The DJG family is committed to creating a child restraint with the most comfort and convenience available today Remember parents are a child s first teachers and examples If you always buckle your seat belt your child will think it is the natural thing to do Make it a firm rule that the vehicle does not go until everyone is buckled up Make no exceptions No one can predict if use of a child restraint will prevent injury or death in a particular crash However combined with careful driving proper use of a child restraint can lower a child s risk of injury or death in most crashes Your child s safety is worth the time it will take to read and follow these instructions After reading if you still have questions or have any problems with this child restraint please contact our Consumer Relations Department at Dorel Juvenile Group Inc Website www djgusa com Fax 1 800 207 8182 Mailing Address Do
16. mine if your vehicles belts are compatible with this child restraint If you will use the LATCH system refer to the LATCH section ELR Emergency Locking Retractor Belts Definition These belts only lock in a sudden stop or crash To see if you have this type of belt pull on the lap belt let it return part way then pull on it again If it moves freely it is an ELR belt and the child restraint could work loose during normal driving Refer to your vehicle owner s manual ELR shoulder belts either require a locking clip or cannot be used with any child restraint Note You may use an ELR lap and shoulder belt when using this child restraint as belt positioning booster no locking clip is required ELR lap only belts must be replaced with a manual belt contact your vehicle dealer A locking clip will not correct this problem Automatic Passive vehicle seat belts Automatic passive 2 point belt has no lap belt You must install a lap belt to secure a child restraint You may also need to install an extra lap belt for an automatic 3 point belt Refer to the vehicles owner s manual A locking clip will not correct this problem Vehicle belt too short Contact your vehicle dealer for a seat belt extender Belts in center of the door or side panel A or middle of the vehicle seat cushion B T 1G You must move the child restraint to another seating location A locking clip will not fix this problem See Locking Clip
17. of the warning labels or other labels on the child restraint APlacing your child in a hot child restraint may result in burns ADo not use this child restraint without the seat pad ARead instructions for other warnings General and Warm Weather Use To help protect your vehicle seat s upholstery from damage use a towel underneath and behind child restraint To avoid your child being seriously burned take the following precautions Park in the shade or where sun does not directly hit the child restraint 2 Cover the child restraint with a sheet or blanket when not in use 3 Check for hot seat and buckles before placing child in child restraint Registration and Recall Information Child restraints could be recalled for safety reasons You must register this restraint to be reached in a recall Fill out the registration card attached to the child restraint or send your name address and the restraint s model number and manufacturing date to Dorel Juvenile Group Inc P O Box 2609 Columbus IN 47202 2609 Attn Consumer Relations or call 1 800 544 1108 You can now register your child restraint online at www djgusa com Please do not send in your registration card if you registered your child restraint online For recall information call the U S Government s Vehicle Safety Hotline at 1 888 327 4236 TTY 1 800 424 9153 or go to http www NHTSA gov Aircraft Installation This restraint is cert
18. ould be seriously injured or killed ANever take your child out of the child restraint or try to tend to your child s needs while the vehicle is moving Never leave child unattended ADo not use a child restraint with damaged or missing parts A WARNING ADo not use cut frayed or damaged harnesses ADo not lubricate buckles and fasteners ADo not substitute parts or try to modify the child restraint in any way ADo not use a child restraint that has been in a crash You must get a new child restraint AUse the child restraint only on vehicle seats that face forward Do not use on seats that face the sides or rear of the vehicle ACheck the vehicle or LATCH belt before each use Use only if the belt can be tightened properly and securely AThis child restraint should be securely belted in the vehicle even when not in use In a crash or sudden stop an unsecured child restraint could injure other occupants ADo not use this child restraint if the midpoint of your child s head is above the top of the child restraint s back ADorel Juvenile Group does not recommend the use of any child restraint accessories except those provided by DJG ANever allow any child to play with this child restraint it is not a toy A WARNING ASecure the top anchorage strap tether provided with this child restraint as specified in both the vehicle and child restraint manufacturer s instructions ADo not remove any
19. pplicable steps Oon To Attach Top A ema Anchorage Strap Put knee in child restraint and push down attach hook to anchor in vehicle To Adjust Top Anchorage Strap To tighten pull on free end of top anchorage strap Pull loose end to ase yo ueak 42AO WO 0 1 1 S8 EP HE 81 81 101 SI Ob ZZ 2SN Buldej pPaeM4o4 To loosen lift up on top anchorage lock and push lock toward top anchorage hook d f0 for Ss O PS s o a oO gt 0 ros z 5 ai ag Tal A un oe Q S m No mMm Li v 9 o ee o g 7 N z a oO pu wn 0 0 faa Love O 5 wn 0 oa faa Belt Positioning Booster Use A Refer to the Choosing Restraint and Position section to make sure your child is at the proper weight and height to use the belt positioning booster Do not use LATCH or tether strap when using the Belt Positioning Booster You MUST fasten the LATCH belt hooks together behind seat When your child is over 40 Ibs 18 1 kg or 43 110 1 cm and over year old you must remove the harness and use this child restraint as a belt positioning booster Loose LATCH hooks can result in serious injury or death Removal of Harness Harness must be removed for use as a Belt Positioning Booster 29 From the back of the seat unfasten harness from splitter plate Pull harness adjustm
20. r Relations Department P O Box 2609 Columbus IN 47202 2609 Fax orders to 1 800 207 8182 Please make money orders payable to Dorel Juvenile Group Inc Fill in the area below to charge to Visa or Mastercard We do not accept personal checks or Discover Card All outside of U S and Canada MUST use credit card Ship To Please Print Name Address City State Province Zip Telephone Email Address We MUST have this information to process your order Model Number 5 digits amp 3 letters Manufacture Date mm dd yyyy
21. rel Juvenile Group Inc P O Box 2609 Columbus IN 47202 2609 Telephone 1 800 544 1108 7 A M to 6 P M EST M TH 7 A M to 4 30 P M EST FRI On the back of the shell there is an expiration date for use of this child restraint Do not use this seat after the expiration date Table of Contents WAPI SS AE E EE 2 4 General and Warm Weather Use cccccscscssssssesssesecsesesesesesees 5 Registration and Recall Aircraft Installation svcscccsscssecccsscccssscsesnscaxseavesseaancsencovesessvs assisveeisves Understanding Your Vehicle cssessessssseesessesseeseeseeseeseeseeseess 6 7 Child Restraint Parts cssscscssssssnssesssseossssseansnsesssseivornsassssseossssseons 8 9 Choosing Restraint and Position ssscsessessessesseeseeneeseeees 10 Preparing Child Restraint to Fit Your Child ou 11 13 Harness Heightsiccscscsascissccscsasstacvcsesecessessscvsciesoontuesesscssznes 12 13 Install Cup Holder on select Models cssesssssessesseeseeseeees 13 Securing Your Child in Child Restraints 14 15 Removing Child From Child Restraint ccsssssssesseeseeseeees 16 Choosing LATCH or Vehicle Belts 0 cctssessessessessesseeseeseeaes 17 Knowing Your Vehicle Belts csssssesesessssesseeseeseeseeneens 18 19 Forwatrd Facing Use cc scscsscssisesessissosassssssessessscosssscosastssssessesasssesses Forward Facing Installation Vehicle Beltecssccssissssissssssssssistsessssssecassssezadetsnsasetsoetsstease
22. section Twist vehicle seat belt and latch plate or buckle Manual Belts Manual lap belts are common in the center rear seat and can allow the child restraint to loosen when it is tilted or jarred After tightening the lap belt securely tilt and push the child restraint forward and to both sides If no loosening occurs your child restraint should be secure If loosening does occur try the following If the buckle plate slides on the belt turn the buckle plate over If the buckle slides turn the buckle Refasten the vehicle lap belt The release button should face out after twisting so that it is easy to reach in an emergency If the lap belt continues to loosen the child restraint must be moved to another location in the vehicle A locking clip will not correct this problem see your vehicle owner s manual AWARNING Failure to check and adjust the manual belt as described above can result in serious injury or death Forward Facing Installation Forward Facing Use After deciding whether to use your Vehicle Belts or LATCH be sure to read the warnings below as they pertain to both systems When LATCH is not being used fasten belt hooks together behind the child restraint as shown AWARNING Loose LATCH hooks can result in serious injury or death AWARNING Using this child restraint in any vehicle seat where the lap or LATCH belts cannot be tightened securely
23. ssnsss LATCH E A E Adjusting the Top Anchorage Strap Tether 27 Belt Positioning Booster Use s ssssssssseessesssseeesssssesseeeesseseeeees 28 Removal of Harness Belt Positioning Booster Installation tseesseseseeeeseees 31 32 Reinstall Harness sississscisssssccssssesessssssssotssssssessstsorsveisosszesiencsezess 33 34 Removing Seat Pad for Cleaning cesessesesecsesecseeseeseens 35 36 Locking Clip easscceccssccsiossedesaazechscssccusilaceassdssastsdescosedencsstasbesscebsess 37 38 Trouble Shootings iaa 39 PATRE T O EEEE AA 40 Replacement Parts Order Form ssssessssseesssesrseseseesrsseeeeneees 41 42 WARNING Failure to follow these warnings can result in the serious injury or death of your child To help you recognize those instructions which are most critical for your child s safety we use this symbol A AAccording to accident statistics children are safer when properly restrained in the rear seating positions than in the front seating positions ANever place a child less than one year old forward facing ACheck vehicle instructions for more information about air bag child restraint use AMake sure the harness height is correct for your child s size AThe harness must be snug AThe vehicle or LATCH belt must stay tight at the belt path When you switch from one mode to the next review the sections of this instruction manual that apply to that mode If you don t your child c
24. the chest not the face or neck Pull up on the shoulder belt to tighten Check periodically to ensure your child has not moved out of position and loosened the shoulder belt AWARNING Check vehicle instructions for more information about air bag child restraint use Do Not Use only the lap belt when using this seat as a belt positioning booster without the internal harness The shoulder belt must always be adjusted snugly across the child s chest NEVER place the shoulder belt under the child s arms Failure to follow these warnings can result in serious injury or death to your child 32 Reinstall Harness From the front of child restraint push buckle s metal plate through pad and shell Make sure buckle faces out From underneath pull buckle s metal clip through pad and shell Pull up on buckle to make sure buckle s metal plate stops against the shell AWARNING Failure to place buckle s metal plate completely through pad and shell can result in serious injury or death to the child 33 continued on next page Thread the harness down through slot on left side of shell 1 across bottom of shell 2 and up through Removing Seat Pad for Cleaning slot on right side 3 AWARNING Thread one latch plate Do not use this child restraint without site harness from back the seat pad Failure to do this can to front 4 Thread the result in serious
Download Pdf Manuals
Related Search