Home

Dimension One Spas Sarena Bay User's Manual

1. Symptom Problem Corrective Action Will not turn on No power Check circuit breaker and or GFCI in any mode Turns on by itself Normal automatic daily No action required power filtration or anti freeze cycle Burned out bulb Replace bulb Pump shuts Automatic timer Push JETS pad again to start another cycle down has shut pump off unexpectedly while in use Motor over heated 2 If pump s will not restart when JETS pad is pushed call for service and automatic protective device Make sure that the equipment panel vent area is not blocked Vent blockage has shut down can cause serious damage to your equipment pump s 47 2003 Sarena Bay Export Owner s Manual Electrical System Cont Symptom Problem Corrective Action 3 flashing LEDs Possible sensor errors Check water level appear on the Top Side Control 2 Clean filter If problem persists Turn off power 2 Restart the system If problem persists Call for service Spa lights always Whenever the lights are Because both lights are synchronized together they always return to a common start in the turned off they always starting point after they have been turned off for more than five seconds This default light turn on in Color Fade ensures that they will remain synchronized sequence Fast mode Water System Symptom Problem Corre
2. ea Rane aR SAS 28 Standb onem a 28 Programming the Scrolling Message Cente Le 28 SIS the te E 28 al 29 Filter Danan PN 29 me RE 29 Pump R n rte dE uM LE ut E C 29 Temperature Unit t D e te et LAT 30 VISIO MN CARTIER D 30 Waterfall R n TiMe to obvii ELA muti eens 30 Digital Display VVindow InVebt 30 M toro eI PE 30 Control Pans NGC 30 POST AMAA ore duc 3l POST AMINE 3l Control xui eee 3l Dynamic Massage Sequelcef cocos round O LLL E M ELLA LH le M 32 Control Panel DescriptIOE OA o 32 Massage Zone eec esi 34 Operating the Dynamic Massage 5 35 ADJUSTING THE FOUNTAIN Un EE e une epa Ee ea PLE s naa 36 2003 Sarena Bay Export Owner s Manual ADJUSTING WATE
3. D E IM M Tt i 2 jm Pr nati P PDA 2003 Sarena Bay Export Owner s Manual 2003 Sarena Bay Export Owner s Manual Table of Contents SAFETY FIRS TSR IMPORTANT SAFETY INSTRUCTIONS LEE READ AND FOLLOW ALL INSTRUCTIONS GAO HYPERTHERMIA 5595 3 DO S AND DON TS 4 M M 4 DONE M M 4 WARNING SIGN c ae 5 SARENA BAY M FEA TURES 6 DYNAMIC LED UNDERWATER LIGHT 6 FOUNTAIN pe 6 PERSONAL THERAPY CONTROL TENT PENDING SWITCHES ee 6 REVOLUTIONARY DESIGN FEATURES 7 Innovative Seating For 7 Recliners 8 Bios Wall Bench Seat 8 Bone Se 9 FI 9 Frontal TD 10 Sport Zone Sedt M adatti
4. na maa uten 10 Additional Esc EGG CONO LAE I ici RE Dynamic Massage SEQUENCER IUS M te 12 ocium MI M M ELM MEE 12 Synchronous reri en oett retis de Hp tutu d MUR edis 12 mier 2 me 12 SG 3 RR 13 8 MESS iuc ae he eee ese ance 3 SOE TSP NO 3 Neck Flex OC PLOWS SSNS 14 Jet SYSTEM SELES ctor WI 14 InfraRed Sensop soos cH eR 14 WitraPure Water Management 9ySterm ee 15 VISIO eyes P NR 15 ori dar c 15 ASAS 5 HYDROSPORT AQUATIC FITNESS GEAR OPTIONAL 16 SONIC IMMERSION SYSTEM SIS OPTIONAL es 16 DI REMOTE CONTROL OPTIONAL 16 INITIAL START UP mmc S 17 2003 Sarena Bay Export Owner s Manual OPERATION ww 21 USING THE TOP SIDE CONTROLS SSNS 21 SEFO ESEREN 21
5. Tactile Therapy Patent Pending Patent Pending OptiMounts T OptiMounts UltraPure Filter Skimmer Filter Basket Patent Pending 4 PTC Switches gt Switches Jet Selector Jet Selector alve alve Val 5 Val gt gt Dynamic Dynamic Massage Sequencer Sequencer NeckFlex InfraRed S NeckFlex Jet Pillow LIKED ea Jet Pillow iWatch Top Side Control Top Side Control Scrolling Message Provides full control of all spa Center functions displays status informational and error messages in the Digital Display Window For more information on using this control refer to the Scrolling Message Center section 2003 Sarena Bay Export Owner s Manual Dynamic Massage Sequencer Dynamic Massage Sequencer Fountain Soft Umbrella Shape Dynamic LED lighting with 8 lights Adjustable Interchangeable fountain patterns Landscape focal point Synchronous Spa Lights Large 22 LED main light Simple Design LED lights general PTC Switches Magnetic Personal Therapy Control or PTC switch Patent Pending Under Water Switch Simple Design Provides full control of all special massage sequences You can also control the lights and the jet pump for your BioForm Recliner Seat For more information on using this control refer to the Dynamic Massage Sequence
6. gt Warning 2003 Sarena Bay Export Owner s Manual To Reduce the Risk of Injury The water in a spa should never exceed 40 104 F Water temperatures between 38 C 100 F and 40 C 104 F are considered safe for a healthy adult Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes To Reduce the Risk of Injury Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy pregnant or possibly pregnant women should limit spa water temperatures to 38 C 100 F To Reduce the Risk of Injury Before entering a spa the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating devices may vary as much as 2 5 F To Reduce the Risk of Injury The use of alcohol drugs or medication before or during spa use may lead to unconsciousness with the possibility of drowning To Reduce the Risk of Injury Persons suffering from obesity or with a medical history of heart disease low or high blood pressure circulatory system problems or diabetes should consult a physician before using a Spa To Reduce the Risk of Injury Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate blood pressure and circulation Do not attempt to remove t
7. Danger All models are gravity drained Do not drain water onto your lawn or plants unless all of the bromine or chlorine has dissipated from the water The sanitizer in your water will dissipate quickly by leaving the cover off and exposing the water to direct sunlight Drain and replace your water every six months For heavy water use you may wish to change the water more frequently You may purchase an optional submersible pump from your dealer or from our Virtual Showroom at www d spas com to provide quicker drainage Feature Filter Cleaning Before cleaning the filter element s place the spa in the Standby mode by pressing the Dimension One Spas ICON logo for 5 seconds Your system is equipped with two top access filter cartridges We recommend that you clean the filters every month as preventative maintenance To clean the skimmer filter cartridge lift the center float of the skimmer assembly until it is fully extended Hold the centerpiece of the assembly and turn it counterclockwise until the flats of the basket are aligned with the securing tabs Then pull the basket assembly straight up to remove Next remove the E Z Lock Filter cartridge by twisting the cartridge 4 turn counterclockwise to its stop Be careful not to overturn the filter Then lift the filter out of its canister Clean the cartridge with a high pressure garden hose Every other cleaning soak the cartridges in a filter cleaning solution rins
8. Push the UP or DOWN Buttons in the same manner as setting the clock to select the time you want your filter cycle to start When your desired filter cycle start time is set in the display push the PROGRAM Button to continue The pre set factory default is 2 00 p m to 1 00 p m repeating every 12 hours unless the number of filter cycles per day has been changed Keep in mind that you will later be prompted to set the filter cycle duration and the number of filter cycles Be sure to keep this in mind when programming your filter cycle start time Note During a filter cycle the bottom left of the Digital Display Window will read SPA FILTERING During the filter cycle JETS will activate the first 5 minutes at high speed and the remainder of the filter cycle time at low speed JETS 2 will also activate for minute on high speed and then turn off Filter Cycle Duration After setting the filter cycle start time the top line of the Digital Display Window will read SET CYCLE DURATION Push the UP or DOWN Buttons to toggle between 10 20 30 40 50 or 60 minutes The filter cycle will be at low speed When your desired filter cycle length appears in the Digital Display Window push the PROGRAM Button to select it The pre set factory default is 20 minutes Number of Filter Cycles After setting the length of the filter cycle you will be prompted to set the number of filter cycles The top line of the Digital Display Window will
9. Adjusting the Fountain You can easily adjust the fountain s AudioTherapy and VisualTherapy qualities by making simple adjustments to the fountain The fountain contains two adjustable parts the barrel and the spreader Either or both of these parts may be adjusted to increase or decrease the height of the fountain spray or the spread of the water blossom Adjustments are made by turning the barrel or spreader either clockwise or counter wise depending on the AudioTherapy and VisualTherapy effect you desire You may also remove the spreader head completely to create a bubbler effect You can also add an optional semi circular spreader to your fountain to change the fountain s blossom to 2 blossom This item is available from your Feature authorized DI Spas Dealer or from our Virtual Showroom at www D Spas com Adjusting Water Flow Water flow can easily be adjusted in the following ways Jet Selector Valve et System Selector Valve between y Pivot Seat Pivot Seat and Frontal Therapy Seat Frontal Therapy The Sarena Bay is EE x Seat equipped with three Jet 2 System Selector Valves 7 e These valves can be Ne used to divert jet om power from one 2 seat within the Bio Wall 4 spa to an adjacent Bench seak gt E seat
10. ALL SPA FUNCTIONS LOCKED To lock the panel all the following Buttons must be pushed within 3 seconds Push the Dimension One Spas ICON logo Button 2 Push the Dimension One Spas ICON logo Button 3 Push the ENTER Button Control Panel Unlock To unlock the panel All the following buttons must be pushed within 3 seconds Push the ENTER Button 2 Push the ENTER Button 3 Push the Dimension One Spas ICON logo Button When the last Button is pushed all buttons will be active 30 2003 Sarena Bay Export Owner s Manual Programming Lock The programming lock is to prevent unauthorized programming and water temperature adjustments When the programming lock is engaged all programmed or default functions will operate normally Also the hot tub user may operate the pumps the hot tub light or view the time of day but no programming changes may be made When the programming lock is enabled the Digital Display Window will scroll PROGRAMMING LOCKED twice on the lower left side of the display then a lock icon will be displayed on the right side of the Digital Display Window To enable the programming lock all the following buttons must be pushed within 3 seconds Push the Dimension One Spas ICON logo Button 2 Push the Dimension One Spas ICON logo Button 3 Push the PROGRAM Button Programming Unlock To unlock the Panel The following buttons must be pushed within 3 seconds Push
11. Sa 21 Os greta 22 Jet PAD BUCO Gu a 22 VV ater Feature raat 23 DOWN BUONS E 23 Light Enter SAAR EN Nu EM MAL S E M 24 du IM EI C 24 Et IE 25 Dimension Ore Spas ICON o ates 25 Scrolling Message Center Messdges s cssscssssscsssssssesssnsenssnsensensensensensssnecesouscsssnsesscncenscnsansensensenscnseasenseascnscansenceasansnseasansensensensensens 25 Rirnse Filters use C Cc E 25 FMS NER Mc T pee 25 Chaise MV AC E 26 Ghange Viion Cartridge 26 SP 26 dir 26 Flashing Display and or Check Water Level 27 Erroneous Temperature on the 27 foe C P M 27 27
12. The valves are adjustable and can be M 4 Bench Seat used to suit the bather s taste Simply turn E the valves in a clockwise or al counter clockwise Jet Selector Valve direction to select how IE india EE 3 much water flows to which and seat s BioForm Recliner BioForm Recliner Ow ten Recliner The valves may offer some resistance when the hot tub pumps are on This is a BioForm normal condition and is caused by the Recliner high rate of water flow and pressure that travels through the valves 36 2003 Sarena Bay Export Owner s Manual Adjustable and Interchangeable Jets The Sarena Bay contains three sizes of jets Standard VCR Jets Directional Feature Standard VCR Jets Rotator These jets may be adjusted for volume flow by turning the jet in either clockwise or counter clockwise depending on your desires These jets spin to provide a rotating HydroTherapy session These jets are also rated at 49 2 LPM liters per minute 13 GPM Turning the jet s outer edge in a counter clockwise direction until you feel it release will allow you to remove the jet and replace it with a Standard VCR Jets Directional A variety of additional jets are available from your authorized 01 Spas Dealer that you may select and interchange with Feature this jet to enhance your enjoyment These jets may be adjusted in any direc
13. exceed the most stringent requirements of European Standards EN60335 1 94 EN60335 2 60 97 EN5501 I The Scrolling Message Center lets you relax and enjoy everything your Dimension One spa has to offer Gain a thorough knowledge of the following information before starting up your spa Note Using The Top Side Controls Scrolling Message Center Digital Display Window The Digital Display Window continuously shows the operating status of the 1 hot tub as well as the various monitoring functions self diagnostics and programming information 21 22 2003 Sarena Bay Export Owner s Manual JETS 1 amp 2 Button When the Jets 1 amp 2 Button is pushed m gt e The corresponding spa jet s pump is are energized respective Status Indicator Light is illuminated e The pump speed is indicated in the lower left corner of the Digital Display Window e rotating swirl icon is displayed in the upper left corner of the Digital Display Window The rotation speed of the swirl will vary according to the pump s speed The first time the Jets 1 amp 2 Button is pushed pump starts on LOW speed When the same button is pushed again the pump will change to HIGH speed The third time the same button is pushed the pump will turn off Each time a Jets Button is pushed it activates a programmable automatic shut off cycle The default time is 30 minutes A progress bar indicating the time remaining before
14. sit in a lounge style position to utilize the Bio Wall Designed around specific muscle groups Allows you to sit comfortably in a variety of positions This seat has good depth and allows most users to totally immerse their shoulders in soothing water Jet and light controls at your fingertips 2003 Sarena Bay Export Owner s Manual Frontal Therapy Seat Adjustable jet Frontal therapy Unique aesthetic design Ultra low seating Unique jetting pattern Personal Therapy Control or PTC switch Patent Pending Cool Down Seat Extra large seat Rowing Seat Features adjustable and interchangeable jets This seat has two large jets directed at the front part of the upper and lower body exclusive to Dimension One Spas Inc Wrap around cocoon style seat cradles you in comfort and security Allows for better HydroTherapy and total shoulder immersion for most users Designed around specific neck shoulder and side muscle groups Jet and light controls at your fingertips Allows you to get your upper body out of the hot water to cool down Doubles as a step for easier entry and exit For use with the HydroSport Rowing System Optional Item 2003 Sarena Bay Export Owner s Manual Additional Design Features Dynamic Jet Selector LED Light Valve Fountain OptiMounts OptiMounts PT C Pending PT co Pending Switch Switch Tactile EN
15. 44 GLOSSARY 5 e M 45 TROUBLESHOOTING GUIDE 47 HEATING SYSTEM Pere m 47 ELECTRICAL SYS FEM 47 WATER SYSTEM 48 vi 2003 Sarena Bay Export Owner s Manual 2003 Sarena Bay Export Owner s Manual Safety First Your safety and the safety of your family and friends is very important It is vital to everyone s safety that you read and heed the following safety precautions Review them as often as necessary to ensure that your enjoyment of your new Dimension One Spas Inc product is always safe IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY When installing and using this equipment basic safety precautions should always be followed including READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY When installing and using this equipment basic safety precautions should always be followed including Danger gt Warning Danger Danger Danger Danger Risk of Accidental Drowning Extreme caution must be exercised to prevent unauthorized access by children To avoid accidents ensure that children cannot use this spa unless they are supervised at all times A grounding wire connector is provided on this spa to connect a minimum No 8 AWG 8 4 mm2 solid copper conductor between this unit and any metal equipment metal enclosures of electrical equipment m
16. This will allow air to escape from the pumps 10 Remove the cap from the UltraPure Then remove the canister and the filter basket from the Weir foam blocks Skimmer canister securing each filter 12 Next remove the filters from the Weir Skimmer and UltraPure canisters and fill your hot tub by placing a hose through the empty UltraPure canister on the left side of the Top Side Control UltraPure Filter Weir Skimmer Filter 13 Fill the spa until the water level is slightly below the bottom of the OptiMount located next to the Skimmer Filter Basket on the right side of Top Side Control 14 Once the spa is full turn on the circuit breaker not supplied by Dimension One Spas Flashing dashed lines will appear for 30 seconds on the Digital Display Window followed by the current water temperature flashing 2003 Sarena Bay Export Owner s Manual 15 Push the Jet Pump 3 Button once to turn on pump 3 Let the system run for 10 to 15 seconds to prime the pump 16 Then push the Jets Button the Dynamic Massage Sequencer to the right of the Top Side Control to start pump l Let it run for 10 to 5 seconds to prime pump Press the button again to shut the pump off 17 Then push the Jets Button on the Dynamic Massage Sequencer to the left of the Top Side Control to start pump 2 Let it run for 10 to 15 seconds to prime pump 2 Press the button again to shut the pump off If there is no je
17. cumbersome valves that also control jets in other areas of the spa These jets are interchangeable with rotating jets Zone This zone is designed to massage the back of the legs at the knee area lower thighs and upper calves There are four mini directional Euro Jets that are water volume controllable and provide a narrowly focused massage pattern These jets are interchangeable with rotating jets 34 2003 Sarena Bay Export Owner s Manual Zone F This zone is designed to massage the feet There are two rotating mini Euro Jets that are water volume controllable and provide a narrowly focused massage pattern These jets are interchangeable with directional jets Operating the Dynamic Massage Sequencer Push the JETS Button to turn on the spa pump Select the sequence you want by using the SEQUENCE Button to toggle between the selected massage sequences When the sequence you desire shows an illuminated SEQUENCE Indicator Light through 6 press the BEGIN PAUSE Button to activate the massage sequence SEQUENCE 1 activates individual zones and steps through them one at a time starting with Zone A through Zone F then reverses the sequence The time interval between zones is determined by the Speed Button SEQUENCE 2 functions opposite of above This sequence activates all zones then deactivates individual zones and steps through them one at a time starting with Zone A through Zone F then reverses the
18. more buoyant frame Height adjustable neck therapy Personalized and controllable dynamic massages using our sequencing technologies in each lounge Jet and light controls at your fingertips You never have to move from your seat or even lift your hands from the water to adjust pumps or lights Promotes freedom of movement The Tactile Pending System design includes adjustable and interchangeable foot jets This bench seat can be used in conjunction with the Pivot Seat and functions as a third lounge Allows you to move along the Bio Wall and target different muscle groups Different jet styles give this seat unique combinations of HydroTherapy features adjustable interchangeable jets 2003 Sarena Bay Export Owner s Manual Bench Seat Open Design Patent y Tactile Therap Pending System Unique jetting pattern Pivot Seat Adjustable jets Barrier free Pivot Seat Unique jetting pattern Multi Soft Tile Pillow layout Deep seat Personal Therapy Control or PTC switch Patent Pending Promotes freedom of movement Foot jets with adjustable and interchangeable jets Tactile Therapy Pending System is great for Reflexology Patent Designed around specific muscle groups Features 16 adjustable and interchangeable jets This seat has an extra large back that functions as a regular large spa seat and also allows you to pivot your position and
19. read SET OF CYCLES Push the UP or DOWN Button to toggle between I 2 3 or 4 cycles per day When your desired number of cycles appears on the Digital Display Window push the PROGRAM Button to select it The pre set factory default is cycles per day Long and or numerous filter cycles could cause overheating of the hot tub especially in hot climates Caution Pump Run Time After setting the number of filter cycles the top line of the Digital Display Window will read SET PUMP RUN TIME Push the UP or DOWN Button to toggle between 30 45 and 60 minutes This sets the length of time the pump will run when a jets Button is pushed For example if you choose 45 minutes when you push a jets Button the pump will run for 45 minutes before shutting down automatically When your desired pump run time appears on the Digital Display Window push the PROGRAM Button to select it The pre set factory default is 30 minutes 29 2003 Sarena Bay Export Owner s Manual Temperature Unit Selection After setting the pump run time the top line of the Digital Display Window will read SET TEMPERATURE UNITS Push the UP or DOWN Buttons to toggle from F to C When your desired temperature unit appears in the Digital Display Window push the PROGRAM Button to select it The pre set factory default is Celcius Vision Cartridge After setting the temperature units the top line of the Digital Display Window will read SET VISIO
20. the automatic shut off cycle The automatic shut off cycles are a safety device that will reduce wear and tear on your equipment and reduce energy costs by ensuring that your pumps don t run constantly Feature Up Down Buttons When the Up or Down Button is pushed to change the set temperature the bottom left of the Digital Display Window will read SET TEMP TO After 5 seconds the display will automatically display the current water temperature again The water temperature may be adjusted from 15 59 and 40 104 These buttons are also used to make custom selections when you are programming the Scrolling Message Center See the section on Programming the Scrolling Message Center for more details on changing the your spa s default settings Note 23 24 Light Enter Button PROGRAM Button 2003 Sarena Bay Export Owner s Manual Push the Light Enter Button to control your Dynamic LED lighting This includes both the Fountain and the Spa lights which are synchronized to operate together The lights have three basic Color Effects you can choose Simply press the Light Enter Button until you find the one you want The Color Effects are e Color Fade Slow This sequence rotates through all colors approximately once per minute Start up default e Color Fade Fast This sequence rotates through all colors approximately three times per minute e Color H
21. the special tool If you are not able to locate it contact the Dimension One Spas Service Department to have one sent Be sure the O ring is not damaged and is properly in place when replacing the lens Contact Dimension One Spas if a replacement O ring is needed Note Surface Care Ultralife amp Shell Your equipment has a very high quality finish Stains and dirt will generally not adhere to the surface We recommend cleaning the entire shell surface with Dimension One Spas Water Line Cleaner You may also use Dimension One Spas ph Alkalinity Increaser or mild cleaners like Soft Scrub Be sure to thoroughly rinse the shell After cleaning you will want to restore your hot tub shell s original luster by using Dimension One Spas Poli Gloss Caution Do not use 409 type cleaners or other caustic solutions as they may damage the hot tub shell surface and void the warranty If you are using baking soda to clean your hot tub shell be careful not to get it on the skirt It may bleach the wood Do not use citrus based cleaners on the shell surface Caution 40 2003 Sarena Bay Export Owner s Manual Dimension One EnviroTect Skirts and Vinyl Covers The Dimension One EnviroTect skirts are unaffected by most corrosive substances and will not absorb moisture To maintain the original finish clean with soap and water No sealing or painting is required To maintain a nearly original appearance we recommend app
22. will turn off to allow the water to cool back to the set temperature This is a normal hot tub function No corrective action is necessary The circulation pump and ozone generator will be on while either jet pump is on They will remain on for 30 minutes after the pump s turn off regardless of the water temperature Note The Dimension One Spas Scrolling Message Center Control has a battery back up that will retain the time of day for 30 days even without an active power source Additionally it will also keep your custom programming commands for up to 40 years without power This battery back up will Feature not provide power to heat or operate the hot tub 2003 Sarena Bay Export Owner s Manual Summer Mode The SUMMER feature temporarily disables the circulation pump Cool Off cycle During hot weather the spa can experience Heat Creep Heat creep is caused when the spa during normal maintenance operations cannot dissipate more heat than is generated This may cause the spa temperature to exceed the set temperature and cause a Cool Off cycle In order to prevent the water from becoming cloudy due to the circulation pump being turned off by the Cool Off cycle the spa can be set to bypass the Cool Off cycle This is accomplished by setting the spa in the SUMMER MODE To initiate SUMMER MODE use the Up and Down Buttons to set the temperature to 15 2
23. 597 The Digital Display Window will indicate SUMMER In this mode the pump will run continuously until the water temperature reaches 41 x107 F and then turn off It will remain off until the water temperature reaches 38 C z102 at which point the pump turns on Standby Mode The STANDBY mode allows the user to clean the filter without turning off power to the spa This feature disables all automatic and manual functions To enter the STANDBY mode press and hold the Dimension One Spa s ICON Logo Button for 5 seconds To exit the mode press and hold the Logo Button for 5 seconds If you do not exit the mode manually the spa will automatically return to normal functionality after 24 hours The Smart Winter mode is not affected by the use of the Standby mode Programming the Scrolling Message Center Your Scrolling Message Center is the most advanced in the industry and can virtually walk you through customizing your hot tub to your exact needs To initiate the programming sequence at any time push and hold the Program Button for 3 seconds If within 10 seconds you do not proceed with the hot tub programming the hot tub will automatically exit the programming sequence and revert to the pre set factory default settings To exit the programming sequence at any time push the Enter Button or do not press any button for 10 seconds Any programming changes made up to that point are saved Setting
24. Display and or DO NOT ENTER THE WATER if you see 3 flashing LEDs on the Check Water Level Top Side Control and or the message CHECK WATER LEVEL CLEAN FILTER IF PROBLEM CONTINUES TURN OFF POWER AND RESTART THE SYSTEM IF PROBLEM CONTINUES CALL FOR SERVICE in the Digital Display Window Follow the instructions as stated Check the water temperature if it is above 40 21047 and DO NOT ENTER THE WATER DO NOT ENTER THE WATER if you see a temperature reading of 0 C 32 F or 57 8 C 136 without first checking the actual water temperature with a separate thermometer The system has detected a Temperature Probe Failure and the water may be too hot or too cold to safely use Contact your local Authorized Dimension One Spas Dealer or authorized service center Ice When ICE CONDITION and the water temperature are displayed on the Digital Display Window the air temperature in the equipment can has gone below a factory preset level and the system has activated Smart Winter Mode It will then automatically activate the pump s to circulate water This is a normal hot tub function No corrective action is necessary This feature protects the spa from freezing Feature Cooling When COOLING and the water temperature are displayed on the Digital Display Window the water temperature has reached 1 C 2 F above the set temperature The circulation pump and ozone generator
25. N CARTRIDGE Push the UP or DOWN Buttons to toggle between Yes and If you are currently using a Vision Cartridge select Yes if not select No Selecting Yes will prompt the control to notify you when your cartridge needs replacement When your desired selection appears in the Digital Display Window push the PROGRAM Button to select it The pre set factory default is No Waterfall Run Time After choosing the Vision Cartridge setting the top line of the Digital Display Window will read SET WATERFALL RUN TIME Push the UP or DOWN Buttons to toggle between I 2 3 or 4 hours For example if you choose 2 hours when you push the Water Feature Button the Waterfall will run for 2 hours before shutting down automatically The pre set factory default is 1 Digital Display Window Invert The invert feature will flip the text on the Digital Display Window play so it can be easily read from both inside and outside the hot tub To invert the text simply push the ENTER Button three times To return the text to its original position repeat this process push the ENTER Button three times Control Panel Lock To help prevent unauthorized use of the hot tub the control panel may be locked When the control panel lock is engaged all programmed or default hot tub functions will operate normally but all control buttons will not operate When the panel is locked the Digital Display Window will display this message
26. R FLOW PEE 36 Jet System Selector a i 36 Adjustable and Interchangeable USR 37 Standard VCR Jetse Dir gctionals Me de 37 Scandard V GR ER 37 Mini Jets s RO CAC OR ipea nis Mele M sd ae 38 Mini VCR JEST Directional ence ee sace ds 38 EUG Directiotial s oce e erae 38 Euro SLS OO 38 ROUTINE EQUIPMENT MAINTENANCE ee 39 DRAINING YOUR EQUIPMENT NOS ERE 39 FILTER CEA p em 39 LIGHT BULB REPLACEMENT TESORO es ea aaa 40 SURFACE 40 o SPECS 40 Dimension One EnviroTect Skirts and Vinyl 41 COD OE ette 41 SPECIAL COLD WEATHER 5 555555059 41 Reguired for Winten ziho SRS eie e ho CU ER cas 41 Procedure for Mian cu 42 SPINE NME tet ctetu ese ae ena Ser ONUS 43 WARRANTY SERVICE INFORMATION
27. allow you to choose between two speeds e Low speed for efficient water circulation during heating and filtration modes and for gentle jet resistance or massage action High speed for maximum jet action Selector Valve Located on the top edge of the spa it diverts jet power from one area of the spa to another Serial Number Please use the serial number located on the left corner pedestal in communication with your dealer Slice Valves Valves located within the spa s internal plumbing which are used by service Shutoff Valves personnel to shut off water flow to the heater and pumps All valves must be completely open during normal operations Available on Dimension One Spas only Smart Heat optimizes heat recovery using the amperage that you have available Along with computerized load sharing that automatically recognizes the number of jet pumps in use compares it with the available power Smart Heat recognizes the difference between the set temperature and the actual water temperature and adjusts the heater to optimize the heater output Temperature Measures the temperature of the water inside the spa This temperature sensor Sensor is used to control the spa heater and the temperature is displayed on the spa side control panel Top Side Used to control temperature pumps for jets spa light system clock automatic _ Control Panel traton cles and _ Connects the spa plumbing to the equipment The unions allow a serv
28. and Step Read all Directions and Safety Precautions on the Swimming Pool or Recreational Vehicle antifreeze bottle before opening and using Ensure that it is non toxic and safe for this use Beware of and follow all safety precautions 2003 Sarena Bay Export Owner s Manual 17 Using a long funnel begin pouring non toxic swimming pool or recreational vehicle water system antifreeze into the filter canister fittings bleeder valve fittings and jet fittings of your system Continue adding antifreeze until it comes out of the drain fittings or from the opening you are pouring it into You must complete this task for every jet fitting in the system Some of the antifreeze will seep into the system from the drain or jet fittings which is okay the goal is to have anti freeze collect in the areas of the plumbing that would normally trap water Use the funnel to also place antifreeze into the pump housing s When pouring antifreeze into the rear most bleeder valve fitting you may see antifreeze pouring from one or both of the circulation system return fittings DO NOT USE AUTOMOTIVE COOLING SYSTEM ANTIFREEZE IN YOUR SYSTEM IT IS TOXIC AND HARMFUL TO HUMANS AND ANIMALS CHECK WITH YOUR LOCAL SPA DEALER OR RV DEALER TO PURCHASE NON TOXIC ANTIFREEZE THAT IS COMPATIBLE WITH DRINKING WATER SYSTEMS Danger 18 Replace all equipment access panels onto the system 19 Replace thermal cover and secure locking tabs If your system is loca
29. button is pushed again The BEGIN PAUSE Button status light will be on when the system is in the Pause mode During this mode the matrix of LED s will preview the sequence and the user may also push the SEQUENCE Button to preview another sequence The SEQUENCE Button is used to toggle between selected massage sequences When a sequence has been selected the corresponding LED indicator 6 will light The default mode all jets in the lounge operating will not be indicated by a light The Massage Zone Indicator Lights Human Figure will be lit to identify which zone is currently active More information on the muscle groups associated with each zone is provided in the Massage Zone Description section When a sequence is chosen one or more LED in the figure will illuminate showing the active zones in that sequence When you have selected the massage sequence you want press the BEGIN PAUSE Button to start your massage 33 2003 Sarena Bay Export Owner s Manual SEQUENCE Indicator Lights The SEQUENCE Indicator Lights indicate which massage sequence has been chosen by illuminating the corresponding light In the default mode all jets in the lounge are operating The default mode is indicated when no lights are illuminated Massage Zone Description The Dimension One Spas Dynamic Massage Sequencer lets you enjoy a wide variety of massage patterns on the most critical muscle groups of your body You can choose from six automa
30. ctive Action Pulsating jets Water level too low Fill with water to the bottom of the OptiMount located next to the Skimmer Filter Basket No Jet Action Jets are turned off Turn jets on by turning jet face clockwise or action is 2 Diverter Valve 2 Turn the Diverter Valve clockwise or counter clockwise turned 3 Dirty Filter 3 Clean Filter 4 Air lock Loosen pump union to allow air to bleed 5 Gate valve closed 5 Open gate valve The Check Possible sensor errors Check water level Water Level scrolling message and or 3 flashing a Turn off power L E D s appear on the display 2 Clean filter If problem continues b Restart the spa 4 f problem persists a Call your dealer for service Fountain The bottom of the The water level in the spa is too high Remove enough water to return the water doesn t drain fountain has water that level to slightly below the bottom of the OptiMount located adjacent to the will not drain out Skimmer Filter Basket 48 2003 Sarena Bay Export Owner s Manual 49 2003 Sarena Bay Export Owner s Manual BEST OF CLASSE 5 2 a gt eue poolandspa com DNV DNV Certification REGISTERED FIRM
31. e using a spa The consumer products safety commission has stated that the water temperature in a spa or hot tub should not exceed 40 C 104 F Immersion in water in excess of 40 C 104 F can be hazardous to your health Observe a reasonable time limit when using the spa Long exposures at higher temperatures can cause high body temperature Symptoms may include dizziness nausea fainting drowsiness and reduced awareness These effects could result in possible drowning Do not use the spa under the influence of alcohol narcotics or other drugs Use of the spa under these conditions may lead to serious consequences Always test the hot tub water temperature before entering the spa Enter and exit the spa slowly Wet surfaces can be very slippery Never bring any electrical appliances into or near the spa Never operate any electrical appliances from inside the spa or when you are wet 2003 Sarena Bay Export Owner s Manual Proper chemical maintenance of spa water is necessary to maintain safe water and prevent possible damage to spa components Caution Use the spa straps and clip tie downs to secure the cover when not in use This will help to discourage unsupervised children from entering the spa and keep the spa cover secure in high wind conditions There is no representation that the cover clip tie downs or actual locks will prevent access to the spa Caution Do s and Don ts Do DO read all op
32. e hot tub below the skirt on the left corner of the side containing the Top Side Control 4 Close the valve on the side of the hose bib and screw it onto the end of the hose bib Check to ensure the cap on the hose bib is secure to avoid leaks when you add water to the spa 5 Remove the panels below the Top Side Control and the right side to expose the pumps and the Lower Equipment Compartment 6 There are two pump unions and two gate valves per pump The pump on the left in the picture shows the typical locations of the pump unions and gate vavles Check to make sure the pump unions are hand tight to prevent the possibility of leakage Next check the gate valves to make sure they are fully opened and that the red safety clips are snapped into place The other pumps in the picture are identified by the additional circles Be sure to check the pump unions and gate valves for all three pumps 7 After you finish checking the pump unions and gate valves remove the shipping bolts from the base of each pump 8 Next check the fittings on the two circulation pumps located at the bottom of the Lower Equipment Compartment to make sure they do not leak 2003 Sarena Bay Export Owner s Manual 9 Open and remove the two bleeder valves One is located in the skimmer area to the right side of the Top Side Control and the other one is located across the spa in the UltraPure area on the left side of the Top Side Control
33. e it thoroughly and reinstall Replace the skimmer basket assembly and the access lid or cover Exit the Standby mode by pressing Dimension Spas ICON logo for 5 seconds After cleaning run the pump for a few minutes at high speed then return to the heating mode To clean the UltraPure filter cartridge remove the E Z Lock Filter cartridge by twisting the cartridge 84 turn counterclockwise to its stop Then lift the filter out of its canister Clean the cartridge with a high pressure garden hose Every other cleaning soak the cartridge in Dimension One Spas Cartridge Cleaner then rinse it thoroughly and reinstall Replace the access lid or cover Exit the Standby mode by pressing Dimension Spas ICON logo for 5 seconds 2003 Sarena Bay Export Owner s Manual Light Bulb Replacement All systems are equipped with Dynamic LED Light bulbs To change the bulb 2 3 Turn the power off and drain the system below the level of the light Using the special tool provided in the owner s manual packet unscrew the cover for the light housing Remove the old bulb and install the new bulb Use the special tool to replace the cover for the light housing Check to ensure proper operation of the new bulb before refilling the system Do not attempt to remove the light housing cover without lowering the water level below the light housing cover Warning Do not attempt to remove the light housing cover without
34. ection mode to maintain water circulation during freezing conditions whenever the system has proper electrical power and water level Therefore a fully operational system is your number one defense against freeze damage If you find it completely necessary to drain your water during the winter months in an area where freezing conditions may exist please adhere to all of the instructions in this section to minimize the risk of freeze damage Failure to complete any of the steps satisfactorily will increase the chance of freeze damage as small amounts of water trapped in pipes will expand as it freezes and may result in damaged plumbing lines or fittings Dimension One Spas does not recommend that you drain your system for the winter Freeze damage caused by winterizing your system is specifically not covered by Your Warranty Caution Items Required for Winterizing Phillips head screwdriver 40 6 cm 16 Channel lock pliers High pressure air blower Commercial grade wet vacuum 1 37 liters 3 gallons to 22 74 liters 6 gallons of Non Toxic Antifreeze Strong able bodied people capable of lifting system Into upright position Enough time and patience to perform all steps 41 2003 Sarena Bay Export Owner s Manual Procedure for Winterizing 2 Shut the power off to the system and make sure that it cannot be accidentally turned back Remove filter elements from f
35. erating instructions read understand and follow all Safety Danger and Warning instructions before use DO test water temperature with your hand before entering to be sure that it s comfortable e DO keep the spa cover closed when the spa is not in use This is also the key to economical spa operation DON T block the equipment compartment vents Blockage may cause damage to the spa equipment and will void the warranty DON T block or sit on the filter recess area DON T allow horseplay or unsupervised use of your Sarena Bay allow anyone to tamper or play with any of the safety or suction fittings of your Sarena Bay 2003 Sarena Bay Export Owner s Manual Warning Signs Each spa has been provided with a Warning Sign and an Important Notice label DURING PREGNANCY SOAKING IN HOT WATER MAY CAUSE DAMAGE TO THE FETUS LIMIT USE 10 MINUTES AT A TIME PREVENT DROWNING PREVENT CHILD DROWNING SPA HEAT SPEEDS UP EFFECTS OF ALCOHOL WATER ATTRACTS CHILDREN DRUGS OR MEDICINE AND CAN CAUSE UNCONSCIOUSNESS IMMEDIATELY LEAVE SPA IF ALWAYS ATTACH A SPA COVER AFTER UNCOMFORTABLE OR SLEEPY EACH USE This label outlines safety precautions This sign should be permanently placed in a location that is visible to the spa user Replacement signs can be obtained from Dimension One Spas 2611 Business Park Drive Vista CA 92083 760 727 7727 This spa is insulated with high densit
36. etal water pipe or conduit within 1 5 meters 5 feet of the spa Risk of Serious Injury or Death The suction fittings in this spa are sized to match the specific water flow created by the pump Should the need arise to replace the suction fittings or the pump be sure that the flow rates are compatible Never operate the spa if the suction fittings are broken or missing Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting Risk of Electric Shock Install at least 1 5 meters 5 feet from all metal surfaces As an alternative a spa may be installed within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum No 8 AWG 8 4 mm2 solid copper conductor attached to the wire connector on the grounding lug inside the equipment compartment on the equipment can Risk of Electric Shock Do not permit any electrical appliance such as a light telephone radio television etc within 1 5 meters 5 feet of a spa The electrical supply for this spa must include a suitably rated switch or circuit breaker to open all ungrounded supply conductors to comply with section 680 42 of the National Electrical Code ANSI NFPA 70 1993 The disconnect must be readily accessible and visible to the spa occupant but installed at least 1 5 meters 5 feet from the spa water gt Warning gt Warning gt Warning eS Warning Warning
37. ference on hot tub operation If you have any questions please contact your local Authorized Dimension One Spas Dealer 2003 Sarena Bay Export Owner s Manual Revolutionary Design Features Innovative Seating For 7 Pivot Seat Soft Tile Pillows Frontal Therapy Seat Bio Wall Bench Seat Bench Seat Tactile Tactile Therapy Therapy Patent Pending Patent Pending BioForm BioForm Recliner Recliner Sport Zone Seat Step 2003 Sarena Bay Export Owner s Manual BioForm Recliners No float angles Upright position Multiple Lounges Accommodate Different Body Styles NeckFlex Jet Pillow Dynamic Massage Sequencing lounges Personal Therapy Control or PTC switch Patent Pending Bio Wall Bench Seat Open Design Tactile Therapy Pending System Pivot feature Freeform jet patterns Jet variety These seats have been designed to accommodate your body s natural buoyancy They allow you to sit more comfortably and relax during jet use Allows for better communication between spa users The two BioForm Recliners have been specifically designed to accommodate the variances among users both men and women can equally enjoy maximum benefits of lounge style therapy The BioForm Recliner located to the left of the Top Side Control is designed for a larger size frame while the one on the right of the Top Side Control is designed for a smaller size
38. gramming instructions for VISION as outlined in the next Vision Cartridge section to set the six month time frame Note Spa Check Up When SPA CHECK UP is displayed on the Digital Display Window we recommend that you have your hot tub inspected by your dealer as a preventative maintenance measure To reset this message push and hold the Dimension One Spas ICON logo Button located at the right hand side of the control for 3 seconds The system can dismiss and reset the maintenance messages by pushing and holding the Dimension One Spas ICON logo on the right end of the control for 3 seconds If you press the Dimension One Spas ICON logo for 5 seconds when there is no maintenance message it will put the spa in the Standby mode Note Overheat DO NOT ENTER THE WATER when OVERHEAT is displayed on the control system Digital Display Window because the hot tub is in a high temperature condition If such a condition exists check the water temperature with a certified thermometer if it is above 40 21047 remove the hot tub cover and allow the water to cool If the problem recurs turn off all power to the hot tub and contact your local Authorized Dimension One Spas Dealer or authorized service center The overheat condition could be caused by excessive filtration See the Troubleshooting Guide section for more information 26 2003 Sarena Bay Export Owner s Manual Flashing
39. he light housing cover without lowering the water level below the light housing cover Do not block air intakes located on the front left corner underneath the hot tub the front right corner for the Chairman ll and Triad Il and under the equipment access panel Resulting malfunctions are not covered under warranty 2003 Sarena Bay Export Owner s Manual Hyperthermia Prolonged immersion in hot water may induce hyperthermia A description of the causes symptoms and effects of hyperthermia are as follows Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 37 C or 98 6 F The symptoms of hyperthermia include dizziness drowsiness lethargy and fainting The effects of hyperthermia include e Failure to perceive heat e Failure to recognize the need to exit spa Unawareness of impending hazard A Warning gt Caution gt Caution gt Caution gt Caution gt Caution gt Caution Fetal damage in pregnant women Physical inability to exit spa Unconsciousness resulting in the danger of drowning The use of alcohol or drugs can greatly increase the risk of fatal hyperthermia in hot tubs and spas Persons suffering from heart disease diabetes high or low blood pressure any condition requiring medical treatment pregnant women the elderly or infants should consult with a physician befor
40. ice Venturi device used to inject air into the Vision Cartridge A safe water sanitizer that can be used in place of chlorine Water Return In addition to the skimmer the water return fittings provide water inlets to your Fittings spa pumps DANGER Never Block Or Remove Any Of The Water Return Fittings A floating water referencing device that skims debris from the surface of the water 2003 Sarena Bay Export Owner s Manual Troubleshooting Guide Heating System Symptom Problem Corrective Action Does not heat Temperature setting is Turn up the thermostat too low 2 Dirty filter 2 Clean filter 3 Flow switch malfunction 3 Call for service Too hot Temperature setting is to Turn down the thermostat high 2 High limit tripped 2 Callfor service Erroneous Possible temperature sensor Call for service temperature of failure 0 C 232 57 8 136 F appears on the display Hot Tub Water level Fill with water to the bottom of the OptiMount located next to the Temperature Skimmer Basket erratic Display reads Too much filtration Reduce the number of filter cycles and or the filter cycle duration OVERHEAT 2 Temperature setting too 2 Turn down the thermostat high 3 High limit or sensor 3 Call for service problem Electrical System S C
41. ilter assembly Drain water from the system using the drain fitting and garden hose or you may use a submersible pump for f Open the equipment compartment and locate pumps and heater Remove all of the drain plugs from each pump Loosen unions on both sides of each pump and the heater if applicable If your system has a Dynamic Jet Sequencer please remove that access panel as well and loosen all unions on each of the sequencer valves There are 6 sequencer valves that means that you will have to loosen 2 unions Tip the system onto one side The system will have some water remaining which will add to the weight Be sure to have enough people available to safely lift the weight of your system Do not tip system onto equipment bay side Close all jets by turning jet faces counter clockwise 9 13 Put on your protective goggles in order to protect eyes from air water antifreeze or debris exiting the jets or drains Insert the hose of a high pressure air blower into the filter element fitting Some models may have 2 filters Begin with the left hand filter fitting which will help evacuate water from the circulation pump system Then proceed to the right hand filter fitting When using air blower on single filter systems or the right hand fitting on dual filter systems rotate each of the jet faces clockwise to open and counter clockwise to close again Do this to each jet face one jet at a time Be careful as water will be com
42. ing message will also appear on the lower line of the Digital Display Window reading SPA HEATING TO C whatever the set temperature is as well as an animated icon on the Digital Display Window Once you have verified that the heater is functioning you can reinstall the ventilated equipment access panel 20 2003 Sarena Bay Export Owner s Manual Depending upon the size of the hot tub and the size of the circuit breaker used heating will occur at the rate 1 65 C 237 to 5 5 C 109 per hour After completing the above steps it is necessary to ensure proper water chemistry See the Water Care Guide for easy steps to maintaining clean and safe water The schedule shown may require more frequent adjustment depending on the bather load Place the thermal cover on the hot tub to conserve energy and to keep it ready for use 2003 Sarena Bay Export Owner s Manual Operation Advanced microprocessor technology has been utilized to produce the Scrolling Message Center The most technologically advanced hot tub control in the world is also the easiest to operate Dimension One Spas has put every hot tub function within fingertip control Temperature setting jet power control the hot tub light and all other functions are spa side accessible That means you don t have to get out of the hot tub to enjoy complete control of all hot tub functions Safety is assured through design concepts and materials that meet or
43. ing out of each jet fitting as you perform this maneuver Perform this operation until no more water is coming from the jets Remove jet faces and insert the hose of a high pressure air blower into each jet fitting Continue this process until no more water comes out of any jet fitting or drain fitting and you no longer hear water gurgling within the plumbing Place all jet faces in a plastic bag and set aside until you are ready to use your system again Remove both bleeder valves from the top of the filter canister area Place hose of a high pressure air blower into the rear most bleeder fitting first Confirm that water mist is blowing from one or both of the circulation system return jets in the footwell of the system You may also get some water mist blowing from the filter canister Repeat this process with the front most bleeder fitting Confirm that water mist is blowing from the drain fittings of the jet pumps Place the hose of a commercial grade wet vacuum over each jet fitting bleeder valve fitting and drain fitting to draw out as much remaining standing water as possible Remove drain hose bib assembly from the outside bottom of the system 42 4 Use the wet vacuum to remove standing water from the pumps and any other fittings within the equipment compartment Once you are sure that all water is evacuated from the plumbing and equipment of the system put the system back down in its normal position and repeat Step 10
44. l of 45 7 square meters 150 square feet High volume pumps pull spa surface water through the skimmer to remove floating contaminants Allows users to massage feet during HydroTherapy Design is based on standard Reflexology maps Change flow to suit your needs Doubles as a rowing station Allows for variable workouts Easy to set up and use Allows user to readily adjust the amount of resistance provided by the HydroSport equipment by adding or moving the Tensor Cords as desired Long lasting and durable Mounted around seat for more comfort Provides increased functionality Long lasting and easy to care for 2003 Sarena Bay Export Owner s Manual NeckFlex Jet Pillow Adjustable Interchangeable Jets Jet System Selector Valve Adjustable Water Flow Customize your HydroTherapy Session InfraRed Sensor Remotely Control The Sarena Bay The NeckFlex Jet Pillow offers five height adjustable positions to accommodate different body sizes Mini directional jets can be interchanged with rotating jets and are adjustable for water volume Customize the flow of water to your seat by simply turning the valves in a clockwise or counter clockwise direction These valves will divert jet power from one seat within the spa to an adjacent seat Adjust your HydroTherapy session by simply adjusting the water volume to the jets in your seat The infrared sensor allows you t
45. lying 303 Protectant at least once a month on the Dimension One EnviroTect skirts and on the vinyl covers if they are exposed to direct sunlight 303 Protectant is rated at 40 SPF Sun Protection Factor Care for the Wood Spa Cabinet When properly cared for the wood cabinet of your hot tub will maintain its beauty for many years All woods react differently to the elements by expanding and contracting To protect your beautiful wood finish re stain it every 3 6 months with Dimension One Spas Redwood or Coastal Gray Stain which serves as a good sealing agent for the wood Please note that the cabinet is not warranted against reaction to natural weather conditions The wood must be properly maintained Should your hot tub cabinet require re conditioning try Dimension One Spas Wood Refurbishing Kit Special Cold Weather Instructions Slipping into your steamy water on a snowy winter night is a refreshing experience Many times people who could never imagine being outside in winter weather find themselves spending their winter nights doing just that while relaxing in their hot tub with family and friends Therefore the best winterizing tips of all are to enjoy use of your system year round All systems manufactured by Dimension One Spas are designed for rigorous winter use They are insulated to keep operating costs down and to protect plumbing and equipment whenever the products are operational Each product line incorporates freeze prot
46. o remotely control the following spa features or functions using the optional DI Remote Control e jets e Water Feature Fountain e Interior Spa Lights 2003 Sarena Bay Export Owner s Manual UltraPure Water Management System This spa is equipped with a highly advanced hot tub water treatment method the UltraPure Water Management System The UltraPure Water Management System is an integrated water management system with ozone injection dual contact chambers and 24 hour filtration Energy conversation is designed into the UltraPure Water Management System The circulation pump has a built in heat recovery system that diverts circulation pump heat directly to the spa water This feature reduces demand on the spa heater and saves energy PAIT Feature To prevent the hot tub from overheating the circulation pump turns off when the water temperature rises 1 1 C 22 F above the set temperature When the water temperature cools down to the set temperature the circulation pump will turn back on The circulation pump will run for short periods when the water temperature is 1 19 C 2 above set temperature to verify temperature Vision Vision an alternative purification system can be used in conjunction with your UltraPure Water Management System The advantage of Vision over conventional halogens bromine and chlorine is that it will as a result of lower chemical use provide softer feeling wate
47. old Hold on any of the colors The default Color Effect is Color Fade Slow Use the Light Enter Button to change Color Effects as follows e Start on Color Fade Slow default e Turn off for second back on again for Color Hold e Turn off for second back on again for Color Fade Fast e Turn off for second back on again for Color Hold e Turn off for second back on repeats to Color Fade Slow e Turn off for 5 or longer start on Color Fade Slow For your convenience and cost savings the lights will automatically turn off after one hour To reactivate the lights after they have been shut off by the timer simply press the Light Enter Button again The lights will always start in the Color Fade Slow sequence after they have been off for more than 5 seconds to ensure they always remain synchronized Note The Light Enter Button is also used to exit programming sequence whenever you have entered the programming mode by first pressing the Program Button The PROGRAM Button is used to initiate the time setting filter programming and other programming features For more information see the section on Programming the Scrolling Message Center Heat Status Light Dimension One Spas ICON Logo 2003 Sarena Bay Export Owner s Manual The Heat Status Light will turn on when there is call for heat and the heater engages This is a normal function The right side of the Digital Display Window will con
48. on or off The status light below the button will illuminate when the light is on The spa light may be turned on off with this button or the one on the Top Side Control They work interchangeably JETS Button The JETS Button turns the jet pump associated with the Massage Sequencer on or off The status light below the button will illuminate when the light is on The Spa jet may be turned on off with this button or the one on the Top Side Control They work interchangeably 32 SPEED Button BEGIN PAUSE Button SEQUENCE Button Massage Zones 2003 Sarena Bay Export Owner s Manual The SPEED Button is used to change the time interval between each step in the sequences The default time is 5 second intervals The first push of the SPEED Button will change the step interval time to 15 seconds the second push will change the intervals to 30 seconds and the third push will reset the speed to 5 second intervals The status light below the SPEED Button will blink at the speed at which the system is operating During a Pause condition the Speed status light will be OFF The BEGIN PAUSE Button is used to interrupt the massage sequence and to start a particular sequence For example If the user likes the jet massage at a particular moment during the sequence and wants to keep it for an extended period of time the user may press the BEGIN PAUSE Button and the system will remain in the specific configuration until the
49. provide a concentrated body massage When the circuit breaker size is smaller than the total power needed to operate both the heater and the jet pump at the same time load sharing automatically turns off the heater when a jet pump is turned onto high speed The electronic control system that governs all of the electrically operated components of your spa utilizes an advanced microprocessor and solid state electronic devices to activate all user and maintenance options A backlit highly reliable liquid crystal display gives you a complete update of the spa status at any time of the day or night Temperature setting as well as control of the light jets filtration and time of day display are all instantly available from and controllable at the topside control panel Ozone A specialized ultraviolet light that changes oxygen into ozone for use in the water Generator sanitation process adequate water flow to turn the heater Load Sharing Lower Control System ICON Pad This is a pad accessed by pressing the Dimension One Spas Logo on the far right of the Top Side Control Panel 45 46 2003 Sarena Bay Export Owner s Manual Term Definition Produces water flow through the heater filter sanitation system and the main jets in the spa The pump will operate automatically during filtration and heat cycles This pump can also be operated manually by depressing the jets pad on the topside control panel which will
50. r Additionally low chemical levels can mean fewer dissolved solids which results in less water chemistry maintenance Please refer to the Vision instructions for proper installation Also read the Water Care Guide for more information Smart Heat On all Dimension One Spas when the water temperature is at least 0 55 C I below the set temperature the heater will turn on and remain on until the water temperature rises to 0 55 I above the set temperature Smart Heat recognizes the difference between the set temperature and the actual water temperature then determines the rate of heating required to best maintain the set temperature Load Sharing Load Sharing recognizes the number of jet pumps in use and compares it with the available power Computerized load sharing adjusts the heater to maximize the heater output based on heat requirements and spa operation then optimizes heat recovery using the amperage that you have available 2003 Sarena Bay Export Owner s Manual HydroSport Aquatic Fitness Gear The optional HydroSport Aquatic Fitness Gear provides a high quality fitness training and exercise system for water based use It is designed specifically for use with the Aquatic Fitness Systems and the Sarena Bay The HydroSport Rowing System and the HydroSport Aquatic Fitness Bar provide exercise gear that quickly installs to various OptiMount locations and allow you to work on your upper body and arm
51. r desires Turning the jet s outer edge in a counter clockwise direction until you feel it release will allow you to remove the jet and replace it with a Mini VCR Jets Rotator Euro Jets Directional These jets are rated at 22 7 LPM 6 GPM and may be adjusted in any direction The jets may be positioned to focus your Hydro Therapy comfort in a specific area and will hold their direction Volume is adjustable by turning the jet either clockwise or counter clockwise depending on your desires Turning 5 outer edge in counter clockwise direction until you feel it release will allow you to remove the jet and replace it with a Euro Jets Rotator Euro Jets Rotator These jets are rated at 22 7 LPM 6 GPM and may be adjusted for volume flow by turning the jet in either clockwise or counter clockwise depending on your desires These jets spin to provide a rotating HydroTherapy session Turning the jet s outer edge in a counter clockwise direction until you feel it release will allow you to remove the jet and replace it with a Euro Jets Directional 38 2003 Sarena Bay Export Owner s Manual Routine Equipment Maintenance Draining Your Equipment Risk of Accidental Drowning Extreme caution must be exercised to prevent unauthorized access by children To avoid accidents ensure that children cannot use this system unless they are supervised at all times
52. r section Provides relaxing VisualTherapy and soothing water sounds Dramatic nighttime VisualTherapy display of the fountain feature synchronizes with the spa lights Customize the fountain look feel and sound by making simple adjustments or adding an optional semi circular fountain head Fountain makes your spa a focal point of your landscaping with beautiful shape light and sound Solid and changing color patterns synchronizes with the fountain light Easy to change and install e Color changing e long bulb life e great look Jet and light controls at your fingertips One set of PTC Switches is available for each BioForm Recliner Seat Pivot Seat and Frontal Therapy Seat Easy to use without leaving your seat Is easy to service 2003 Sarena Bay Export Owner s Manual Weir Basket Skimmer Large Canister Filter Skims surface contaminants Tactile Therapy Pending Raised profile details Unique design Adjustable jets HydroSport OptiMounts Shown With Optional Sport Zone Seat HydroSport Rowing System pee Design can accept more than one tether Simple Design 6 OptiMounts OPTIMounts OPTIMounts All stainless steel construction Flexible soft pillow Flexible Diamond Shape Material Each Weir Basket houses a Dimension One Spas Inc Canister Filter with 22 9 square meters 75 square feet of filtration providing a tota
53. s with simple exercises The versatile HydroSport Aquatic Fitness Gear is all you need for a variety of aquacizing options Sonic Immersion System SIS Optional The optional Sonic Immersion System provides a superior fidelity and low distortion stereo system featuring patented planar magnetic speaker technology 64 cm 1 4 thick that generates unparalleled sound quality even in the harshest environmental conditions Unique speakers offer multidirectional capability allowing you to enjoy fantastic audio with a rich bass sound in your backyard even when you aren t using the spa The Sonic Immersion System provides an extra dimension to your Sarena Bay s AudioTherapy capabilities Additionally it can be operated remotely using the remote control provided with the system or the optional floatable DI Remote Control DI Remote Control Optional The optional DI Remote Control unit is an infrared device that floats It is used to remotely control the following spa features or functions e Jets e Fountain e Interior Spa Light 2003 Sarena Bay Export Owner s Manual Initial Startup Locate the Top Side Control 2 Locate the hose bib that is included in the owner s manual packet The owner s manual packet is shipped inside the equipment compartment Your dealer should provide you with this packet during installation 3 Locate the male fitting at the bottom of the lower left corner of th
54. se contact your local Authorized Dimension One Spas dealer 43 2003 Sarena Bay Export Owner s Manual Warranty Service Information Your hot tub warranty gives you specific coverage Be sure to read the enclosed warranty sheet carefully The warranty does not cover problems arising from misuse abuse or neglect and it does not cover problems caused by improper installation or perceived problems caused by failure to read the hot tub owner s manual A service charge will be made if a service call is made for any of the following 44 Equipment failure due to improper inadequate electrical service All systems require dedicated circuits as described in this manual Low voltage can cause equipment failure and seriously shorten equipment life It is the owner s responsibility to ensure proper electrical service is available Failure of hot tub to reach desired temperature because the set temperature is not turned up high enough Maximum thermostat setting is approximately 40 C 104 Burned out hot tub light Bulbs are not covered Hot tub water chemistry is the responsibility of the hot tub owner Cloudy dirty or chemically unbalanced water and cleaning of the hot tub filter are also the responsibility of the hot tub owner Hot tub shell or equipment damage caused by improper water maintenance Serious damage can be caused if your hot tub water is not maintained carefully and correctly Poor jet action because
55. sequence The time interval between zones is determined by the Speed Button SEQUENCE 3 activates alternate zones It sequences Zones A C and E first then switches to Zones B D and F second The time interval between Zone Groups is determined by the Speed Button SEQUENCE 4 activates individual zones and steps through them one at a time starting with Zone A through Zone F then it starts over in groups of two zones incrementing the zones i e Zones A B Zones C etc The time interval between Zone Groups is determined by the Speed Button SEQUENCE 5 starts with Zone A and adds a new zone during each step in the sequence until all zones are active Then it reverses the sequence by removing a zone during each sequence step until all zones have been removed The time interval between Zone Groups is determined by the Speed Button SEQUENCE 6 provides random groupings of two zones starting with adjacent zones i e Zones A B then Zones B C etc then opposite zones i e Zones A F then Zones B F etc and finally the middle zones i e Zones then Zones etc The time interval between Zone Groups is determined by the Speed Button If the time between sequence changes is too fast or too slow you can push the SPEED Button to increase or decrease the time between sequence changes Five seconds is default Other speeds available are 15 and 30 seconds 35 2003 Sarena Bay Export Owner s Manual
56. t action then the water level is too low or there is air trapped in the plumbing lines To eliminate the trapped air turn the pumps on and off several times to force the trapped air through the pumps If there is still no jet action and the bleeder valves were removed as previously described turn off the pumps and loosen the top pump unions slightly to let any trapped air escape Re tighten the pump unions and turn the pumps on again Turn the pumps on and off several times until jets function properly Ozone bubbles will continue to release from the skimmer recess Ultra Pure bleeder valve as long as the valve remains open Once the pumps are primed be sure that the bleeder is closed tightly Note 12 When the jets are in full operation replace and close the bleeder valves and push the UP Down Buttons until your desired water temperature set temperature is indicated on the Digital Display Window The Digital Display Window will then display your set temperature for thirty seconds before changing to display the current water temperature While setting the temperature the Digital Display Window will read out the temperature up to 40 C 104 Water temperatures in excess of 40 104 should be used with extreme caution Warning Initial start up you can confirm that the heater is on by looking to see that the heat LED indicator located on the right side of the hot tub control panel is illuminated A scroll
57. ted in an area of high snowfall you may want to take one more extra precaution to safeguard the life of your system cover Span the cover with 2 or more 2x4 s cut to length to reach the outside edges of your cover Place a sheet of plywood cut to fit each half of the cover over the 2x4 s this will carry the load of a heavy snow load and prevent the cover from warping or breaking You can even tarp the system at this point for maximum protection Spring Time Startup In the spring or when your ready to start the system back up follow these instructions e Make sure o rings for pumps are in place and undamaged e Make sure all the fittings that you had to loosen are tightened Replace all jet fittings pump drain plugs hose bib drains and bleeder valves e Fill the system up as you would normally do e Turn the power back on the jets on high speed for about 15 minutes e Drain the water e Put your filter s back in Refill and treat chemically like you would during a normal water change Your system is equipped with automatic freeze protection However power outages can cause your system equipment to freeze quickly During freezing conditions check your system frequently to ensure proper operation Always check your system after any power failure to ensure that it is operational Draining and not operating your system disables this feature Caution For additional information about winterizing your spa plea
58. the Dimension One Spas ICON logo located at the right hand side of the control for 3 seconds On alternating months the top line of your Digital Display Window will read DIRTY FILTER and the message REMOVE FILTERS amp CLEAN IN SOLUTION PUSH AND HOLD ICON BUTTON MORE THAN 3 SECONDS TO RESET THIS MESSAGE will scroll from right to left on the bottom line of the display To reset this message push and hold the Dimension One Spas 78 ICON logo Button located at the right hand side of the control for 3 seconds 25 2003 Sarena Bay Export Owner s Manual Change Water Every four months the top line of your Digital Display Window will read CHANGE WATER and the message TURN POWER OFF DRAIN amp REFILL SPA PUSH AND HOLD ICON BUTTON MORE THAN 3 SECONDS TO RESET THIS MESSAGE will scroll from right to left on the bottom line of the display To reset this message push and hold the Dimension One Spas 7 ICON logo Button located at the right hand side of the control for 3 seconds Change Vision Cartridge When CHANGE VISION CARTRIDGE is displayed the Digital Display Window the system is telling you that it is time to replace it To reset this message push and hold the Dimension One Spas 1 ICON logo Button located at the right hand side of the control for 3 seconds If you purchased a Vision cartridge subsequent to the initial start up of your hot tub please follow the pro
59. the ENTER Button 2 Push the ENTER Button 3 Push the Dimension One Spas ICON logo Button When the last Button is pushed all buttons will be active Control Panel Reset This function is used to completely reset the clock and all other system variables to the factory defaults Please keep in mind that this resets all maintenance messages clean filters change water etc as if the hot tub is being installed the day of the panel reset To reset the control system all of the following buttons must be pushed within 3 seconds Push the ICON logo Button 2 Push the ENTER Button 3 Push the PROGRAM Button The top line of the Digital Display Window will read RESET PROGRAMMING The bottom line of the Digital Display Window will read IF SO PUSH ICON 4 Push the Dimension One ICON Button to reset the entire control system to factory defaults or do not touch a button for 10 seconds to exit 3l 2003 Sarena Bay Export Owner s Manual Dynamic Massage Sequencer The Dynamic Massage Sequencer is located in the Ultra Lounge of the models mentioned above The sequencer directs a succession of 14 jets to six separate muscle groups When a sequence is chosen a human figure with LED s defining each zone will light showing the active zones in that sequence This allows you to preview the zones in the sequence before a selection is confirmed Control Panel Description LIGHT Button The LIGHT Button is used to turn the spa light
60. the Time After holding the PROGRAM Button the top line of the Digital Display Window will read SET TIME OF DAY and the bottom line will read PUSH UP OR DOWN TO CHANGE PUSH PROGRAM TO SELECT NEXT FUNCTION PUSH ENTER TO EXIT Push the UP or DOWN Buttons to engage the time setting mode The time screen will appear with hours 00 flashing on and off Push the UP or DOWN Button to increase or decrease the number until the desired hour appears When the desired number is displayed push the LIGHT Button to accept the selection and change the flashing number to the ten minute place 12 0 Adjust the number with the UP or DOWN Button in the same manner as the hour number When the desired indicator is displayed push the LIGHT Button to accept the selection and change the flashing number to the minute place 12 1 Adjust this number with the UP or DOWN 28 2003 Sarena Bay Export Owner s Manual Button in the same manner as the hour number When the desired number is displayed push the LIGHT Button to accept the selection and change the flashing number to a flashing AM or PM indicator Adjust the indicator with the UP or DOWN Buttons After reaching the correct time push the PROGRAM Button to set the time and exit the time setting mode You will then be prompted to set the filter start time Filter Cycle Start Time After setting the time of day the top line of the Digital Display Window will read SET FILTER CYCLE TIME
61. the jet Selector valve is in the middle position For full performance turn the jet Selector valve to either the full clockwise or full counterclockwise position Do not block air intakes located on the front left corner underneath the hot tub the front right corner for the Chairman ll and Triad and under the equipment access panel Resulting malfunctions are not covered under warranty Warning 2003 Sarena Bay Export Owner s Manual Glossary of Terms Term Definition Bleeder Valve A small valve used to relieve or expel air from the spa s plumbing or pump Circulation A pump that circulates the water in the spa continuously Pump Dry Firing Turning the heater element on when there is no water in the heater Provides access to your spa s equipment for a qualified service technician Your spa s filters have been designed so that you may repeatedly clean and maintain the filter element as needed The element is constructed of woven polyester rather than paper to ensure long life and proper filtration A type of Circuit Breaker that automatically disconnects power to the spa when there is an electrical power leakage to ground Equipment Access Panel Filter Cartridge GFCI Ground Fault Circuit Interrupter Valve Halogens Free chlorine bromine or iodine ions that are very strong oxidizers used to llla Return the water into the spa from the equipment The jets produce a turbulent flow of water mixed with air to
62. the pump will turn off is displayed immediately following the pump speed message The pump automatic shut off cycle is programmed separately All pumps are controlled by the same automatically shut off cycle The automatic shut off cycles are a safety device that will reduce wear and tear on your equipment and reduce energy costs by ensuring that your pumps don t run constantly Feat cature Additionally this feature allows for convenient filtration immediately after use of the hot tub by letting you push the Jets Button as you leave to get an additional 30 45 60 minutes of filtering Jet Pump 3 Button When the Jets 3 Button is pushed The corresponding spa jet pump is energized e The respective Status Indicator Light is illuminated e The pump speed is indicated in the lower left corner of the Digital Display Window Arotating swirl icon is displayed in the upper left corner of the Digital Display Window The rotation speed of the swirl will vary according to the pump s speed 2003 Sarena Bay Export Owner s Manual Water Feature Button When the Water Feature Button is pushed the pump controlling the fountain is activated A second push will turn the pump off Each time the Water Feature Button is pushed it activates a programmable automatic shut off cycle The default time is hour Your choices are 2 3 or 4 hours See the section on Programming the Scrolling Message Center for details on changing
63. tic jetting sequences managing six different zones for a rapidly adjustable HydroTherapy massage session Zone A This zone is designed to massage neck and deltoid muscle groups using the NeckFlex Jet Pillow There are two directional mini jets on the NeckFlex Jet Pillow carrier that can be adjusted to five different heights in order to accommodate a variety of body sizes The mini jets are water volume controllable and provide a narrowly focused massage pattern They are interchangeable with rotating jets Zone B This zone is designed to massage the upper back shoulders and thoracic muscle groups There are two rotating VCR Jets which are water volume controllable and can be adjusted to change the area of coverage and the speed of the rotational pattern These jets are interchangeable with directional jets Zone C This zone is designed to massage the middle back There are two directional VCR Jets that are water volume controllable These jets provide excellent therapy for back muscles They are interchangeable with rotating jets Zone D This zone is designed to massage the lower back and lumbar muscle groups There are two directional VCR Jets that are water volume controllable The directional VCR jet also provides an adjustable nozzle that can eliminate air induction This adjustment allows the user to control the water velocity or the intensity of the massage at each individual jet without the need for
64. tinue to read the current temperature while the bottom left corner will scroll the message HEATING C until the hot tub reaches the set temperature An animated thermometer will also be displayed in the upper center of the Digital Display Window to confirm heater activity If the water reaches 2 above the set temperature the message COOLING TO CIRC PUMP amp O3 OFF will be displayed in the bottom left hand side of the Digital Display Window and a cooling cycle will start The time of day can be viewed by pushing the Dimension One Spas ICON logo on the far right of the control panel If no other button is pushed within 5 seconds the display will revert to the hot tub water temperature reading The pre set factory default is Fahrenheit Pressing the logo for 5 seconds will place the spa in the Standby mode and allow the spa to be cleaned without turning off the power Scrolling Message Center Messages Because of the advanced programming features of your scrolling Digital Display Window your hot tub will prompt you when you need to perform routine maintenance For example Rinse Filters Every other month the top line of your Digital Display Window will read RINSE FILTERS and the message REMOVE FILTERS amp RINSE WITH HOSE PUSH AND HOLD ICON BUTTON MORE THAN 3 SECONDS TO RESET THIS MESSAGE will scroll from right to left on the bottom line of the display To reset this message push and hold
65. tion and are rated at 49 2 LPM liters per minute 13 GPM The jets may be positioned to focus your HydroTherapy comfort in a specific area and will hold their direction Volume is adjustable by turning the jet either clockwise or counter clockwise depending on your desires A variety of additional jets are available from your authorized D Spas Dealer that you may select and interchange with this jet to enhance your enjoyment Turning the jet s outer edge in a counter clockwise direction until you feel it release will allow you to remove the jet and replace it with a Standard VCR Jets Rotator 37 2003 Sarena Bay Export Owner s Manual Mini VCR Jets Rotator These jets are rated at 30 3 LPM 8 GPM and may be adjusted for volume flow by turning the jet in either clockwise or counter clockwise depending on your desires These jets spin to provide a rotating HydroTherapy session Turning the jet s outer edge in a counter clockwise direction until you feel it release will allow you to remove the jet and replace it with a Mini VCR Jets Directional Mini VCR Jets Directional These jets are rated at 30 3 LPM 8 GPM and may be adjusted in any direction The jets may be positioned to focus your Hydro Therapy comfort in a specific area and will hold their direction Volume is adjustable by turning the jet either clockwise or counter clockwise depending on you
66. with other special spa features to create a unique combination of relaxing Therapies HydroTherapy AudioTherapy and VisualTherapy The easily adjustable fountain offers multiple water flow options ranging from an almost silent waterfall trickle to a much larger circular spray You can even remove the fountain cone and create a soothing Bubbler Nothing says relax like the sound of moving water These variables provide customizable AudioTherapy to suit your special desires The customizable lighting sequences add VisualTherapy impact by coordinating with other spa lighting to create a special atmosphere for your backyard or deck The fountain light is synchronized with the underwater light to provide distinctive choreographed lighting effects for your enjoyment Personal Therapy Control tent Pending Switches Dimension One Spas underwater Personal Therapy Control Pendin PTC switches allow you to control the HydroTherapy Jets and the spa lights from the comfort and convenience of your spa seat Multiple switch locations provide unique control of the pump s that drive the jets in the seats or lounges You can easily use these underwater switches to turn the seat jets on or off or control the spa lights Take the time to read these instructions carefully When installed and maintained properly your Sarena Bay will provide many years of enjoyable trouble free operation Read all of the instructions for further re
67. y urethane foam for structural support and energy efficiency When empty of water and left in direct sunlight without the spa cover in place the spa is vulnerable to ultra violet or solar damage Temperatures generated by sunlight can become concentrated in the spa shell surface causing the shell material to delaminate from the urethane foam back ing This occurrence is considered abuse and may result in blisters bubbles or large layer delaminations This occurrence is not covered under warranty The spa cover must be kept on the spa while empty of water NOTE THIS MARKING IS TO BE REMOVED ONLY BY THE OWNER 2003 Sarena Bay Export Owner s Manual Sarena Bay Features Celebrate with us Dimension One Spas Inc proudly introduces the Sarena Bay and Therapy HydroTherapy AudioTherapy and VisualTherapy The Sarena Bay spa is presented in recognition of Dimension One Spas Inc s 25 years as a leader in the international spa industry This spa also inaugurates several innovative new features Dynamic LED Underwater Lighting Special lighting effects are created by the spa s underwater Dynamic LED Light which synchronizes with the fountain s Dynamic LED Light to provide VisualTherapy using special customizable lighting effects Set the mood with easily adjustable sequences and let these special lighting effects enhance your party atmosphere or encourage your quiet relaxation Fountain The fountain integrates

Dimension One Spas Sarena Bay User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents