Home

Denso BHT-202B-CE/202BW-CE User's Manual

Contents

1. increments by one however replacing the backup battery does not reset the counter to zero automatically You need to reset the discharge counter refer to Section 2 4 2 When the BHT is shipped from the factory the discharge counter is reset to zero 34 Chapter 2 Getting Started the BHT and System Menu 2 4 1 Replacing the Backup Battery NOTE Before proceeding to the replacement procedure below it is recommended that you save important data into the FLASH folder or upload it to the host computer 1 Turn the BHT upside down 2 Slide the right and left release buttons in the direction of the arrows to remove the battery cartridge cover Release button 1 Battery cartridge cover Battery cartridge Battery pull strap 35 4 Pull the lock of the inside cover to the right and towards you to release it PS cover _ Clear insulation sheet 36 Chapter 2 Getting Started the BHT and System Menu 6 Slide the backup battery cover to the right and take it out 7 Lift up the backup battery take its lead wires out of the groove and disconnect the battery connector as shown below pe x Backup battery 37 8 Connect the connector of a new backup battery with the red lead facing to the left 9 Route the lead wires inside the guides through the groove For easier routing use a tool whose tip is thin and round 10 Load the backup battery Backup battery Backu
2. Cable Connection between CU 201 and Modem DTE and DCE In the RS 232C interface specifications the DTEs Data Terminal Endpoint shall be generally connected with each other by a cross mode cable the DTE and DCE Data Circuit Endpoint shall be connected with each other by a straight mode cable The DTE is one piece of equipment connected at both ends of a communications line as a sender or receiver of data such as CU 201 on which the BHT is put and a host PC The DCE is one piece of equipment connected in between the DTE and the communications line and terminates communications lines It converts their signals without any change in contents such as modem or TA CU 221 Use a cable that conforms to the USB specification 145 Appendix A Specifications 5 3 cccissscteces haces cevatsentecnecaiere a e e aa NA E cm ENEN EN YR OE eae 147 A1 BAT 202B CE 202BW CE iusan iiare ii deka e aaa aa prii aaa AA Eia aa adia adaa aa 147 ET Ju Product Sp cifications at iassa Aga ac eal ee a a ee ea el aa 147 21 BarCode Specifications scent Geir ee SE ee a E a ia 148 A25 GU 20Oras aaar ae ed a e a ia n a 151 1 Product Specifications srren a aade a a e e ae aE ea e a Ea aaa TEE e A E a o aaar Na 151 2 Charging Requirements rninn Aoi ead Ae aa a a 151 soil sInlerace SpeciiiCalions z ccecestee ctHatetpectictac bet e oie a eae hs etc ie AAA E a oeton teen centsd 152 Appendix B Loading an Optional Compact Flash Card
3. c ccccccceceeeceeeeeeeeeeneeeeeeaeeeceaeeeseaaeeseaeeeseeeesseaeeeeseeeseneeeess 153 Appendix C Quality Assurance Standards 0 eee cece cee cece cess e esas cease eeneeceesenesceeeseaeesaeeseaeesneeseeeseaeessaeeeeseneeeseeseneeeea 157 C 1 Interface Cables ssi ccieecdacauspcevssccsdcbipcaveacevtennsteavscvisevescesusct sate S aE a A A AEN A A N a aaa 157 Appendices 146 Appendices Appendix A Specifications A 1 BHT 202B CE 202BW CE 1 Product Specifications Power Source Main power Rechargeable lithium ion battery cartridge 3 7 VDC Dimensions W x L x H 90 x 186 x 44 mm 3 5 x 7 3 x 1 7 inches Weight Regular style BHT Approx 380 g Approx 13 4 oz including battery cartridge Grip style BHT Approx 450 g Approx 15 9 oz including battery cartridge loaded in the BHT body only Operating Ambient Temperature 5 C to 50 C 23 F to 122 F Operating Humidity 20 to 80 with no dew condensation Ambient Illuminance 20 to 10 000 Ix Depth of field 700 mm ITF 0 625 magnification PCS value 0 9 min Reflection intensity 85 min for white and 5 max for black 500 to 3000 Ix Depth of field 40 mm PCS value 0 9 min Reflection intensity 85 min for white and 5 max for black Narrow bar width 0 33 mm min Controller CPU 32 bit RISC RAM 128MB Flash memory 64MB Keypad 30 key pad Trigger switches M3 M4 2 Magic keys M1 M2 2 Numerical keys and others 26 26 key pad Trigg
4. To transfer data stored in the BHT to the host PC select UPLOAD To transfer data from the host PC to the BHT select DOWNLOAD For details refer to Chapter 2 Section 2 5 3 Operating in System Menu The BHT and the host PC will start communication with each other via the CU 200 The DATA LED on the CU 200 will come on upon start of communication After completion of communication the LED will go off CU 221 only 4 Connect the USB cable to the USB ports on the host PC and the CU 221 Bee T 5 Turn the BHT on and run System Menu Select 2 Communication and ActiveSync USB 6 Once the connection is complete My Computer and Mobile Device can be viewed allowing data exchange between the host PC and the BHT 141 5 5 Charging the Rechargeable Battery Cartridge using the CU 200 You can charge a rechargeable battery cartridge loaded in the BHT Be sure to turn the BHT off before starting charging Service Life of Rechargeable Battery Cartridge al Sl Lithium ion batteries used in the rechargeable battery cartridge will gradually deteriorate during the repeated cycles of charging and discharging due to its properties even under normal use When the battery service period becomes shortened due to its deterioration even if it has been charged for the specified hours replace the battery cartridge with a new one Generally it is necessary to replace the battery cartridge after it has undergone
5. For the epimeren preme rer tn the i Maral Shutdown due to low battery E Problem When the power is turned on or off or during execution of applications the battery output level has lowered so that the BHT no longer operates If lower battery is detected the BHT beeps five times for 0 1 second per beep and then turns itself off Depending upon the battery level the beeper may not sound five times E Solution Replace or recharge the battery cartridge For the charging procedure refer to Chapter 5 Section 5 5 If the grip style BHT is loaded with battery cartridges both in the BHT body and the grip replace or recharge both battery cartridges Always remove both battery cartridges even if you only have one fully charged replacement battery cartridge on hand Service life warning for backup battery E Problem The backup battery has been charged discharged by the specified number of times so that the battery capacity lowers below the specified level E Solution Replace the backup battery For the replacement procedure refer to Chapter 2 Section 2 4 132 Chapter 4 Error Messages 133 This chapter describes the handling procedure of the communication unit CU 200 the interfacing with the host PC and the charging of the rechargeable battery cartridge 51 Functions ofthe GU 200 a a e a a ra a a Aa aaa eena iae Tara saai a a ipo asa Liina Sao nihana ipn larra biaa 135 5 2 Components and
6. e Setting the CPU performance to Fast consumes much power decreasing the BHT operation period after battery charge e CPU performance settings will be functional after the setting changes are made Chapter 2 Getting Started the BHT and System Menu Double tap the Key and the Key property appears You can define the functions of the following keys SF ALP SF key M1 key M2 key M3 key M4 key M5 key M3 key pressed halfway M4 key pressed halfway M5 key pressed halfway Available on the grip style BHT Defining the SF ALP SF key for keypad shift Choose the SHIFT tab on the Key definition menu to display the screen shown at left Nonlock Shifts the keypad only when the SF ALP SF key is held down Onetime Shifts only one key pressed immediately after the SF ALP SF key is pressed The following keys will not be shifted 83 Defining the M1 M2 M3 left hand trigger switch M4 right hand trigger switch and M5 M5 key available on the grip style BHT Choose the MAGIC Full press tab on the Key definition menu to display the screen shown at left You can define each of the M1 through M5 keys as any one of a trigger switch shift key enter key backlight function on off key Tab key and others as listed below LE Defining the halfway pressed M3 through M5 keys Choose the MAGIC Half press tab on the Key definition menu to display the screen shown at left
7. You can define each of the halfway pressed M3 through M5 keys as any one of a trigger switch shift key enter key backlight function on off key Tab key and others as listed below Choice of keys available In each of the combo boxes on the MAGIC Full press and Half press pages above you can make a choice from a list of keys given below The M1 through M5 keys and the halfway pressed M3 through M5 keys can function as listed below This sample defines the M1 key as a Tab key None The key entry will be ignored aa is Trigger Switch As a trigger switch Shift Key As a SF ALP SF key Enter Key As an ENT key Backlight Key As a backlight function on off key Pon aeae Em 2 Tab As a tab key Laser As a laser lighting key Control As a CNTL key Alternate As an ALT key CLEAR As a CLEAR key 84 Chapter 2 Getting Started the BHT and System Menu If you define the M4 key as a backlight function on off key pressing the M4 key activates or deactivates the backlight function Note that the backlight function on off key can be assigned only to any one of M1 through M5 keys and halfway pressed M3 through M5 keys The key defined more recently will act as a backlight function on off key and one defined earlier will be ignored That is if you define the M1 and M2 keys as a backlight function on off key in this sequence the M2 key will work as a backlight function on off key and the M1 key s entry will be ig
8. and then tap the Connect button to begin connecting to the wireless network Double tap an SSID from the SSID list in the Wireless Information tab to display the screen on the left Perform settings to connect to the wireless network You can set the following Network name SSID Displays the SSID Manually input the SSID if it is not automatically recognized This is an ad hoc network Do not check this check box because ad hoc mode is not supported Encryption Select the encryption mode Authentication Set the authentication system when the WEP is enabled Network key Enter the network key Key index Enter the network key index 109 This key is provided automatically Select this check box to automatically obtain the network key Enable 802 1X authentication Select this check box to enable 802 1X authentication This cannot be used in Ad hoc mode e Security and Setting Method The security level can be changed based on combinations of the encryption and authentication The setting parameters for each security level are shown in the table below Security Setting PEAP EAP TLS PEAP EAP TLS PSK parameter None 802 1x 802 1x WPA WPA WPA Encryption Disabled WEP WEP WEP TKIP TKIP TKIP Authentication Open Open Open Open WPA WPA WPA PSK Network key XXXXXX XXXXXX Key index 1to4 Th
9. AL MU WAYI e When cleaning the keypad do not scrub the surface too hard and do not pull the keys Doing so may break the keys or cause the keypad to dislocate Thorne Sherine e If the BHT or CU becomes smudged moisten a soft cloth with neutral detergent and wring it out thoroughly Wipe the BHT or CU with the cloth and then go over it again with a dry cloth Dust or dirt accumulating on the clear plate of the reading window will affect reading performance If you use the BHT in dusty areas therefore periodically check the clear plate of the reading window and clean it if dusty e To clean the plate first blow the dust away with an air brush Then wipe the plate with a cotton swab or the similar soft one gently e If sand or hard particles have accumulated never rub the plate doing so will scratch or damage it Blow the particles away with an air brush or a soft brush E Limited Warranty on Software Products In no event will DENSO WAVE INCORPRATED be liable for direct indirect special incidental or consequential damages including imaginary profits or damages resulting from interruption of operation or loss of business information resulting from any defect in the software or its documentation or resulting from inability to apply the software or its documentation m DENSO WAVE INCORPORATED does not assume any product liability arising out of or in connection with the application or use of any product circuit or app
10. Arrange two BHTs one as a master station and the other as a slave station to be tested with their IR ports facing each other as illustrated below In this test the slave BHT transmits data to the master BHT and receives the data sent back from the master BHT 0 15m 5 9 or less Master BHT Slave BHT to be tested E Preparation for the USB interface test Connect the BHT and the host computer using a USB interface cable Selecting the 4 COM on the Hard Test menu calls up the screen SELECT ADAT shown at left Loma 1 OPTICAL Switch to the MASTER SLAVE selection 2 ree screen for the IrDA interface test 2 USB Test the USB interface port 97 Testing the IrDA interface port Selecting the 1 0PTICAL on the COM menu calls up the screen shown at left At the slave BHT to be tested select the 1 SLAVE and at the master BHT select the 2 MASTER Then press the ENT key on each BHT During the test the screen shown at left is displayed ee XXXXX Transmission speed 2400 9600 or 115200 bps es YYY Hex data being sent 0 to 256 obo re fon e ee Upon normal completion of the test the tested slave BHT beeps once lt OPTICAL x and displays the screen shown at left Tash Ce The master BHT automatically returns to the COM menu ies Bie g E 98 Chapter 2 Getting Started the BHT and System Menu If the IrDA interface test ends abnormally E OPTICAL T t Wj Jm
11. EELT 46 2 5 3 lt Operating in System MENU karasie e A E ara ead a a el rd 57 2 5 4 Detailed Description of the Functions in System Menu cccccceceseeeeeeceeeeeaeeeeeeaeeesecaeesseaeeeeeneeeessaees 60 1 Execute Prograi c hen aches d aii iaka aa i da Aohud ia a cele Aine 60 2 Communication Men assarrar ad acid AAEE aa A EA ea E eaaa i aa arei a a PER Tetani a d 61 3 System Properties Menu mars n ei a ee el a lel a alate 74 4 Eana e EEEa E lev ees ties ae eee de real Dae in le ele ee ed ec ee es 94 5 Explorer isiydi ddaa adh abhi a adada iay daaa ida neigh ible bbe eal ee 106 6 system nformationics sic aati ana aaraa aaea aaen heh ave aude ini alae aad 106 2 6 Wireless Zero Configuration WZC sears ie a iia adaa d aaa a aE daaa dat 107 2 1 BHT System Configuration The BHT barcode data collection system requires the following hardware as well as the BHT Bar Code Handy Terminal which reads bar codes and accepts keypad entry depending upon the intended system configuration e Host computer Allows you to edit manage and download user programs and data as well as downloading system programs For host computers having no IrDA interface ports the optional CU 200 optical communication unit and RS 232C interface cable for CU 201 or USB cable for CU 221 are available e CU 200 option Exchanges programs and data with the BHT via the IrDA interface and with the host computer via the RS 232C interfa
12. Functions naninira aaa Ea a E a i 136 5 3 Applying Power to the CU 200 csiiiende deine aaaea inden iis ne niet 137 5 4 Communicating with the Host PC ceceeeeseseeeseeseeeeeeeeeeeceneeeeseeesaeseeeeaeseseaeseseaeseseeesaeseeeaeseeeeeseaesneeeeeeatees 139 5 4 1 Setting the Transmission Speed of the CU 200 o oo eee neee sete tenenseeseesetaeeeeeesntee 139 5 4 2 Interface Cable Connection ececeeceeeeseeeeeeeeeseeeeeeeeceeeesesaeeeaesaeeeesaeseeeeaesaeeeaesaeeeaesaeseeesaeseeeeaeeaeeneeeaeeaes 140 5 4 3 Interfacing with the Host PC cece ceceeseeseeeseeneeseesseceeeeseceesaesaeesaesseceaessesenessesseeeaesseeeaesseeeaeeaetaeeneeeateaes 141 5 5 Charging the Rechargeable Battery Cartridge using the CU 200 00 0 eeceeeeeeeeeeeeeeeeneeeeeeneeeeeeeeeeeeeaeees 142 5 6 Interface Specifications 1 Interface Connector and Pin Assignment 2 Interface Cable Connection Chapter 5 Handling the CU 200 Option 134 Chapter 5 Handling the CU 200 Option 5 1 Functions of the CU 200 The optical communication unit CU 200 series is available in two models CU 201 and CU 221 The CU 200 series has the following functions 1 Data exchange function The CU 201 221 exchanges data and programs between the BHT and the host PC Interface with the BHT IrDA interface Interface with the host PC RS 232C CU 201 USB CU 221 2 Battery cartridge charging function The CU 200 charges the rechargeable battery cartridge loaded in th
13. LAN are command controlled by user programs For the setting procedure of RF related parameters refer to Section 2 5 4 3 4 RF Menu Network Interface Control E ESSID Extended Service Set ID An ESSID is an ID that identifies the wireless network Wireless devices having a same ESSID can communicate with each other E POWER This parameter sets the power mode for the wireless module built in the BHT The following six power modes are available Power mode Power consuming state Consumes much power Consumes less power The BHT may take more time to establish the wireless link or send response messages Default E WEP Wired Equivalent Privacy When WEP is ON messages to be sent received over the wireless LAN will be encrypted The WEP KEY uses 40 bit 10 digit hexadecimal or 128 bit 26 digit hexadecimal encryption word The BHT is able to definitely communicate with access points having the same WEP KEY E AUTHENTICATE This parameter sets up the authentication system to be applied when WEP is enabled You can use either one of the two KEYs OPEN and SHARED KEY to disable and enable the authentication respectively If WEP is disabled choose OPEN so that communication is no longer possible E WEP KEY You can set four types of encryption keys WEP KEY1 through WEP KEY4 If you enable WEP choose any one of WEP KEY1 through WEP KEY4 as TRANSMIT KEY 115 E TRANSMIT KEY You need to use the
14. TRANSMIT KEY in order to choose and activate any one of the WEP KEY1 through WEP KEY4 already defined NOTE If the size of the WEP KEY specified as a TRANSMIT KEY for the BHT is different from that for the access point no communication is possible Setting example Communication is possible BHT WEP KEY 1 128bit TRANSMIT KEY WEP KEY1 Access point WEP KEY1 128bit TRANSMIT KEY WEP KEY1 BHT WEP KEY 1 128bit WEP KEY3 128bit TRANSMIT KEY WEP KEY1 Access point WEP KEY1 128bit WEP KEY3 128bit TRANSMIT KEY WEP KEY3 Setting example Communication is not possible BHT WEP KEY 1 40bit TRANSMIT KEY WEP KEY 1 Access point WEP KEY1 128bit TRANSMIT KEY WEP KEY1 BHT WEP KEY 1 128bit WEP KEY3 40bit TRANSMIT KEY WEP KEY 1 Access point WEP KEY1 128bit WEP KEY3 40bit TRANSMIT KEY WEP KEY3 116 Chapter 3 Communications Operations of BHT 202B CE 202BW CE 3 2 Infrared Communication The BHT has an integrated infrared IR communications device which enables wireless transfer of programs and data between the BHT and the host computer and between the BHTs instead of the conventional wire transfer The IR communications device features the following e Wireless communications e Small and lightweight design e Freedom from the codes regulations and licenses which differ from country to country unlike radio devices The BHT may communicate with other IrDA compliant equipment just by aligning their IR ports with each ot
15. The radio frequency module Type LA 4137 that complies with the Directive 99 5 EC R amp TTE is mounted on this device BHT 202BW CE A Declaration of Conformity may be obtained from http www2 symbol com doc Preface Please READ through these operating instructions carefully It will enable you to operate your BHT 202B CE 202BW CE correctly The following contents are explained in this guide e Handling and operating methods for the BHT 202B CE 202BW CE e Communication e Error messages e Specifications e Handling and operating methods for the optical communication unit CU 200 series The BHT 202B CE 202BW CE models are designed in the same way except for the interface differences shown in the table below In this manual operations common for all models are explained unless otherwise stated Wireless Communication BHT 202B CE BHT 202BW CE After you have finished reading the instructions keep this manual handy for speedy reference How this book is organized This manual is made up of five chapters and appendices Chapter 1 Quick Guide Describes the basic operating method of the BHT and the related notes Chapter 2 Getting Started the BHT and System Menu Summarizes the BHT system configuration and describes the operation including preparation and System Mode which is required for the efficient use of application programs Chapter 3 Communications Operations of the BHT 202B CE 202BW CE Describe
16. Ymodem in the Communication menu calls up the screen shown at left Button i Sets the communications environments Button Downloads a file to the BHT Button 3 Uploads a file stored in the BHT to the host computer 61 E Setting the communications environments Tapping button i on the Ymodem menu calls up the communications environments setting screen When using connector interface Pot WLA e Sata icon Baty ive a e Ce creat a When using IrDA interface Pot EEE Rao ismo ce Sonia el To communicate with the host computer via the connector interface port select Serial COM1 in Port The screen shown at left appears In BaudRate Parity and StopBits select the same setting as that in the host computer Data bits are fixed at 8 To communicate with the host computer via the IrDA interface port select IrDA COM4 in Port The screen shown at left appears In BaudRate select the same setting as that in the host computer Other settings are fixed as follows Data bits 8 Parity None Stop bits 1 After the BHT is initialized the interface port and communications parameters are set as listed in the default table below Items Defaults Port IrDA COM4 Baud Rate 115200 bps Data Bits 8 Parity None Stop Bits 1 62 Chapter 2 Getting Started the BHT and System Menu E Downloading cal Trane Specify a folder where you
17. You can configure beeper sounds for various events G Aucteartal Giese magam ical Stop Leta Sore Deby termi Bin ff Eacarration Sour Dray pos el a here r kar esias Panjo e 52 Chapter 2 Getting Started the BHT and System Menu Display Properties On the Control Panel window double tap Display and the Display Properties window appears Tap the Background tab to display the screen shown at left You can select wallpaper to be displayed on your desktop Tap the Appearance tab to display the screen shown at left You can specify the appearance of your desktop On the Control Panel window double tap Regional Settings and the Regional Settings Properties window appears You can specify the display format for the following Region Language Input 53 Connection On the Control Panel window double tap Network and Dial up Connection and the Connection window appears Double tap the Make New Connection icon starts Wizard Follow the Wizard instructions and set the connection name and type Tap the PC Connection tab to display the screen shown at left You can change the connection method to the PC Tap the Change Connection button Coe weer Free Pine roienaly r Ponjo me 54 Chapter 2 Getting Started the BHT and System Menu Date Time Properties Cotes Tin i nets E Ti On the Control Panel window double tap Date Time and the D
18. and other sources of radio waves in the 2 4 GHz band Electromagnetic noise from personal computers refrigerators and other home appliances can also interfere with link operation Environmental factors that can also interfere with link operation include large metallic objects metallic dust or metallic walls in the vicinity of the path and vibration at either end NOTE To System Designers e Before developing the application make sure that the intended environment is free of the interference factors above and thus actually capable of supporting link operation Assume that there will be communications failures requiring robust retry capabilities in the software When introducing the BHT link operation into an environment where equipment using radio waves in the 2 4 GHz band operates or when introducing such equipment after the introduction of the BHT link operation be sure to confirm that the BHT radio link operates properly with all equipment being in operation beforehand If the environment of the radio communications system is changed after the introduction e g newly installed household appliances and movement addition of shelves or objects then confirm that the radio link operates properly again before the actual use 114 Chapter 3 Communications Operations of BHT 202B CE 202BW CE 3 1 2 RF Related Parameters Wireless communication between the BHT terminals and access points that are connected to each other by a wireless
19. approx 300 cycles of charging and discharging operation 1 Turn the CU 200 on The POWER LED on the CU 200 lights in green 2 Turn the BHT off and place the BHT loaded with a battery cartridge onto the CU 200 The BHT turns on the charge LED in red and starts charging Charging time Grip style BHT When power is supplied via Regular style BHT with two battery cartridges loaded AC adapter CU 201 221 Approx 3 hours Approx 5 5 hours USB interface CU 221 Approx 9 hours Approx 21 hours Upon completion of charging the charge LED turns green 3 Take the BHT off the CU 200 142 E Charging Operation and LED Indication Operator s Action CU 200 Status On standby U Place the BHT on the CU 200 Charging U U After approx 3 hours approx 5 5 hours when the CU 201 221 is powered from the AC adapter After approx 9 hours approx 21 hours when the CU 221 is powered from the USB interface y Charging completed Remove the BHT On standby Chapter 5 Handling the CU 200 Option Charge LED on the BHT g p is i p OFF K a h By a ety i Ni q ON in red f 5 ON in green f i Hi i r pa hi OFF For grip style BHTs with two battery cartridges loaded If the CU 221 is self powered via the USB interface from the USB host PC or USB hub and the host PC is in Suspend mode the CU 221 cannot charge the battery cartridge If the host PC switch
20. could cause the unit to heat up inside deforming its housing resulting in a fire S Always use the CU and AC adapter in a well ventilated area e Do not place the CU anyplace where it may be subjected to oily smoke or steam e g near a cooking range or humidifier Doing so could result in a fire or electrical shock e Keep the power cord away from any heating equipment Failure to do so could melt the sheathing resulting in a fire or electrical shock e Do not insert or drop foreign materials such as metals or anything inflammable through the openings or vents into the CU Doing so could result in a fire or electrical shock e If you are not using the CU for a long time be sure to unplug the AC adapter from the wall socket for safety Failure to do so could result in a fire e When caring for the CU unplug the AC adapter from the wall socket for safety Failure to do so could result in an electrical shock viii E Proper Care of the BHT and CU Clean the housings BHT charge terminals battery cartridge terminals and CU 200 charge terminals with a dry soft cloth Before cleaning be sure to turn the BHT power off and unplug the AC adapter of the CU e Never use benzene alcohol or other organic solvents The Bi housing may be marred or the paint may come off Thha ppi e Never rub or strike the liquid crystal display LCD with anything Mg eal hard The LCD surface will be easily scratched or broken
21. entry from the keypad Pressing individual keys displays the identifier letters in the positions pre assigned to those keys on the LCD Pressing the same key again erases the displayed letter rna Mag The table below shows the relationship between the keys and the identifier letters to be displayed on the LCD Key Letter Key Letter Key Letter A A 1 1 F1 F1 y v 2 2 F2 F2 q4 gt 3 3 F3 F3 gt lt 4 4 F4 F4 M1 M1 5 5 F5 F5 M2 M2 6 6 F6 F6 M3 M3 7 7 F7 F7 M4 M4 8 8 F8 F8 M5 M5 9 9 F9 F9 M3 halfway pressed M3H 0 0 FO FO M4 halfway pressed M4H M5 halfway pressed M5H ENT ENT SF ALP SF SF C BS BS BS M5 available on the grip style BHT Note Only when the M1 or M2 key is pressed the vibrator works After all keys are pressed and displayed on the LCD this test automatically ends and the screen returns to the Hard Test menu m a e rF rE Pes 2 Ps Ee a ee Fa e om Th Ce Pas TR Te re Ter Ta a m reat e ENE M5 and M5H appear only on the grip style BHT 105 5 Explorer x Choosing 5 Explorer in System Menu calls up the screen shown at IO DESE mi Eg left ED ipi shinn REH Cata E Hy Faterori Doumer E poika Propan Pini Choosing 6 Version in System Menu calls up the screen shown at left 106 Chapter 2 Getting Started the BHT and System Menu 2 6 Wireless Zero Configuration WZC Gand Benah Mo yal eo hiii hermes nehemia m
22. initialize the memory tap the Yes button to return to the previous menu tap the No button Upon completion of Scandisk it may take a few minutes depending upon the use conditions of the FLASH folder the screen shown at left appears brighi ce 81 3 5 Power Management CPU clock fiwihch bp Stanly Mirin Tree imiji TPU Preface ions Creat fe D Battery Power External Power Double tap the Power Management and the Power Management property appears You can set the automatic power off timer the standby timer and Automatic Power Off Time For the BHT being out of the CU set the automatic power off timer Default 180 For the BHT placed in the CU set the automatic power off timer Default 0 The entry range for the above items is from 0 to 32767 in units of seconds Specification of 0 disables the automatic power off facility When the Enable automatic power off with wireless communication check box is selected the power turns OFF automatically when not performing communication even if a wireless connection is open Switch to Standby Mode Timer x100 ms CPU Performance Normal Fast Set the waiting time to switch to the standby mode within the range from 0 to 32767 in units of 100 ms Default 10 100 ms x 10 1 second Select Normal to operate the CPU at typical clock speed Default Select Fast to operate the CPU at higher clock speed
23. is opened by pressing RF Open Continuously the wireless module remains continuously open even if the NIC Control property is closed To close the wireless module open this menu again and tap the RF Close button E Displaying the IP address and MAC address owl Tapping the Network tab on the NIC Control menu displays the screen shown at left This menu displays the following DHCP Static DHCP enabled or disabled IP Address IP address of the BHT Subnet mask Subnet mask Gateway Default gateway DNS Server IP address of the DNS WINS Server IP address of the WINS MAC Addr MAC address of the BHT Tapping the Property button calls up the IP address setting screen For the IP address setting procedure refer to Section 2 5 2 E Control Panel Owner Properties TIP When the RF device is not opened the MAC address shows 00 00 00 00 00 00 87 E Setting the RF options oil Tapping the ID tab on the NIC Control menu displays the screen shown at left You can specify an ESSID Extended Service Set ID to be used on the communications network For details about the ESSID refer to Chapter 3 Section 3 1 2 RF Related Parameters Tapping the Option tab on the NIC Control menu displays the screen shown at left You can set the following Power Select the power mode for the wireless module Zero config Select the Zero config mode For details about the parameters above refer to Chapter 3 Sec
24. seins 114 3 1 2 RF Related Parameters cccscccssscssececcsseesseceesdeensrseseeessensasansserseseassnsteesoesensnengucesensasepeectscnensepnecseadens 3 2 Infrared COMMUNICATION ie snadia onsen end irra iaa deadibe contin dhacsb dos A ae aa Eria de aaa Kadar biaia 3 3 Connector interface specification 3 4 Basic Communications Specifications and YMOdEM ccccccceeeeeeeeeeeeeeeeneeeeeeeeeeeaeeeceaeeeseeeeeeceeeeseneeeeaees 120 3 4 1 Basic Communications Specifications a ri iiei a ie iE iE Laia a daid 120 3 4 2 Using aaoo Ta aE NE AE ie ea T TTA EA 122 3 5 ACIVESYING si etenee iads aKa Ea a E S AE E A ea E aA a Ea ETa ERES 123 3 5 1 Configuring the Host Computer 0 ceccceceececeeeeeeeeeeaeeeeeeneeeeaeeeeeaaeeecaaaeeesaaeeseaaeeseaeesseaaeeseeeesseneeetsaees 123 3 5 2 Gonnection Using ACtiVeSynNC esiaine naden rean adana pra a AAA A ORA SE O TAKE Aaa 125 113 3 1 Spread Spectrum Communication The BHT 202BW CE supports spread spectrum communication 3 1 1 Notes for Wireless Operations If there are too many communications errors first make sure that the BHT 202BW CE points directly at an access point because the 2 4 GHz band requires a more or less straight line path Note also that the low power radio waves have trouble passing through human bodies and other obstacles along that path This link will not operate properly in the vicinity of microwave ovens industrial heaters high frequency medical equipment
25. the barcode type and the number of digits tja Mag Listed below is a table showing the relationship between the barcode types and the identifier letters to be displayed on the LCD Bar code Type ID Letters EAN 13 UPC A A EAN 8 B UPC E C Standard 2of5 STF H l Interleaved 2of5 ITF CODABAR NW 7 N Code 39 M Code 93 L Code 128 K MSI P EAN 128 W The minimum number of digits to be read is 3 for STF and CODABAR and 4 for ITF 95 4 2 Beeper scale test Selecting 2 BEEPER on the Hard Test menu calls up the screen shown at left and sounds the beeper at three octaves listed below Upon completion of this test the BHT automatically returns to the Hard Test menu bone Scale Frequency Hz do 523 1046 2093 4186 re 587 1174 2349 mi 659 1318 2637 fa 698 1396 2793 sol 783 1567 3135 la 880 1760 3520 ti 987 1975 3951 4 3 Aging test Selecting 3 AGING on the Hard Test menu proceeds to the aging test while showing the current date and time on the LCD This test is intended for personnel who check the BHT in the factory a TIP Once this test is selected the automatic powering off function becomes disabled Foo Meg 96 Chapter 2 Getting Started the BHT and System Menu 4 4 Communications test In System Menu you can test the IrDA interface port and USB interface port E Preparation for the IrDA interface test
26. the character to be transmitted The start stop synchronization is an asynchronous system which synchronizes each character as a unit that is it externally adds start and stop bits to the leading and trailing bit positions of the character to be transmitted respectively A clock starts counting on receiving the start bit and it falls into a non communication state on receiving the stop bit The number of the stop bits is selectable 1 or 2 bits E Transmission Speed Maximum number of bits to be transmitted per second Expressed in bps bits per second E IrDA Interface Communications Range The IrDA interface s maximum effective range is 15 cm 5 9 inches with the IR beam within a 10 angle of divergence To communicate via the CU 200 put the BHT on the CU 200 E Switching Time between Sending and Receiving on IrDA Interface The IrDA interface should satisfy the following requirements in switching between sending and receiving 1 Within 10 ms from completion of sending the IrDA interface should become ready to receive 2 After 10 ms or more from completion of receiving the IrDA interface should start sending 120 Chapter 3 Communications Operations of BHT 202B CE 202BW CE E Transmission Code and Bit Order All characters should be coded to 7 or 8 bit code for data transmission The transmission bit order is LSB Least significant bit first What follows is an example for transmitting character A 41h 01000001b w
27. the file information in the BHT poika Pogan Fes 42 Chapter 2 Getting Started the BHT and System Menu E Recycle Bin On the desktop double tap Recycle Bin The Recycle Bin opens The Recycle Bin stores files you deleted in the BHT To retrieve files stored in the Recycle Bin select the file to be retrieved and choose File Restore To delete a file s in the Recycle Bin from the BHT memory permanently select the file s to be deleted and choose File Delete To delete all files in the Recycle Bin choose File Empty Recycle Bin ine If you delete files in the FLASH folder they will not be stored in the Recycle Bin but deleted from the memory immediately On the desktop double tap BhtShell The System Menu screen shown at left appears For details about this program refer to Section 2 5 3 Operating in System Menu On the desktop double tap Internet Explorer The screen shown at left appears DEN SO 4 With this program you can browse Web pages etry O00 Ap arena 5 NOTE Before running Internet Explorer you need to make RF related s get settings and open the wireless communications device For details refer to Section 2 5 4 3 8 Radio Frequency 43 TIP Configuring Proxy Server When the Internet Explorer runs choose View Internet Options to call up the Options window Tap the Connection tab to display the screen shown at left Make your settings E Messenger mini
28. tray 2 The dialog appears as shown at left Tap the Disconnect button circled in red The BHT beeps once and disconnects the ActiveSync connection The ActiveSync icon disappears 101 4 5 LCD and indicator LED tests Selecting 5 DISPLAY on the Hard Test menu calls up the test pattern shown at left on the LCD and turns on the indicator LED in blue Each time the ENT key is pressed the screen shifts to the next test pattern To return to the previous screen press the C BS BS key To stop this test while in progress and return to the Hard Test menu press the C BS C key C BS BS key f U ENT key As shown at left everything disappear and the indicator LED lights in red C BS BS key ff U ENT key The checker pattern shown at left appears and the indicator LED goes off C BS BS key ff U ENT key 102 C BS BS key ft U ENT key C BS BS key ft U ENT key C BS BS key ft U ENT key Chapter 2 Getting Started the BHT and System Menu The checker pattern is reversed The gray screen appears with a one dot wide white outline Forty eight right angled triangles appear 103 The gradation pattern appears Press the ENT key and the BHT returns to the Hard Test menu 104 Chapter 2 Getting Started the BHT and System Menu 4 6 Key entry and vibrator test Selecting 6 KEY VIBRATION on the Hard Test menu calls up the screen shown at left and makes the BHT ready for
29. units of 100 ms Timeout Specify the timeout period in units of 100 ms for an echo request eeel Type 1 or Type 2 Select the echo request send timing Type 1 or Type 2 described on the next page Count Specify the number of echo requests to be sent To run Ping tap the Ping Start button or press the ENT key TIP Tapping the Ping Start button when the RF device is not opened automatically opens the RF device and runs Ping Entry Range for Data size Interval Timeout and Count Item Allowable entry range Initial value Data size 1 to 2048 32 Interval 0 to 65535 10 Timeout 0 to 65535 10 Count 0 to 65535 4 Specification of zero 0 will set the number of echo requests to be sent to infinite keeping sending echo requests until Ping is aborted If you specify a value out of the allowable entry range listed above the nearest value within the range will automatically apply After Ping runs the screen shown at left appears D ops wer un Pre Le Count Number of echo requests sent OK Number of echo replies NG Number of errors found during execution of Ping Timeout Number of timeouts for echo replies that took place during execution of Ping RTT Ave ms Echo reply time in milliseconds 91 Ping Echo Request Send Timing Two types of echo request send timings are available Type 1 and Type 2 The default is Type 2 e Typel After sending an echo request Ping will wait
30. web site http www denso wave com For further details refer to 2D Code Scanner Barcode Scanner Keyboard Interface with BHT CE kbifCE User s Guide that comes with the software 1 2 Setting and Using the Hand Strap and Stylus E Setting the hand strap Hand strap A E Using the hand strap Put your hand through the hand strap and hold the BHT as shown below This will prevent you from dropping the BHT accidentally Hand strap Chapter 1 Quick Guide E Using the stylus The BHT has a touch screen LCD With the stylus that comes with the BHT you can operate keys menus and icons displayed on the touch screen Before using the touch screen be sure to set it up Refer to Chapter 2 Section 2 3 2 Setting up 2 Calibrating the touch screen e Always use the stylus to operate the touch screen Do not use your fingernails or any pointed or hard object or apply a strong pressure or impact to the LCD e Before operation clean the surface of the LCD and the tip of the stylus if dirty Using dirty ones will scratch the LCD surface or prevent the stylus from sliding smoothly E Operating the touch screen Action Description Tap Refers to touching the LCD once Functionally equivalent to click with a mouse on a PC Double tap Refers to quickly touching the LCD twice Functionally equivalent to double click with a mouse on a PC Drag Refers to moving the stylus to the obje
31. 1 System Errorsed keneeidise ha HA Sa Nl ihe AN N eee 131 130 Chapter 4 Error Messages 4 1 System Errors If some error occurs when the power is turned on or during program execution one of the following error messages will appear on the LCD CTT LETT Terre tT eet TT a bioa syaiem 4 Ce Battery voltage has lowered System Program error Em Problem A System Program error has occurred TE If this error occurs the BHT beeps five times for 0 1 second per beep and then turns itself off E Solution Contact your nearest dealer Low battery warning E Problem When the power is turned on or off or during execution of applications the battery output level has dropped below the specified lower level limit If low battery is detected the BHT displays this message for approx 2 seconds and beeps three times for 0 1 second per beep After that it will resume previous regular operation Solution The battery cartridge will need to be recharged before long Replace or recharge the battery cartridge For the charging procedure refer to Chapter 5 Section 5 5 If the grip style BHT is loaded with battery cartridges both in the BHT body and the grip replace or recharge both battery cartridges Always remove both battery cartridges even if you only have one fully charged replacement battery cartridge on hand 131 Charge the Battery hearers bin sariu fr jak Ei bens betlery wth a rea ore
32. 1 Quick Guide 1 4 Using the Keypad E Entering Numerical Data To enter numerical data use the numerical keys and the ENT key For example to enter the number 120 press the 1 2 and 0 keys and then press the ENT key If you type in any wrong value press the C BS BS key and then enter the correct one E Entering alphabetic characters The alphabet entry procedure differs depending upon the keypad type 30 key pad Holding down the SF ALP key only for the specified period 1 5 seconds or more switches the BHT to the alphabet entry mode You can use the numeric keys and function keys to type in alphabet letters printed on those keys in light blue To switch back to the numeric entry mode hold down the SF ALP key again 26 key pad Pressing the ALP key switches the BHT to the alphabet entry mode You can type in alphabet letters using the numeric keys in the same way as you use a cellular phone If you press a numeric key the alphabet assigned to that key will appear in the ALP window see Chapter 2 Section 2 2 2 Status Indicators on the LCD Pressing the ENT key establishes the alphabet displayed To switch back to the numeric entry mode press the ALP key again For both the 30 key and 26 key pad types you can switch between the numeric and alphabet entry modes also in user programs For programming the mode switching refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual E Using the so
33. 4 ie a BHT sp Circuitry j _ Circuitry wie ER 4 oR 6 RS C7 e cs se 3 1 CU 221 The USB interface on the CU 221 is USB1 1 Full speed compliant with a type B receptacle 152 Appendices Appendix B Loading an Optional Compact Flash Card Load an optional Compact Flash card to the BHT using the following procedure 1 Turn the BHT upside down 2 Slide the right and left release buttons in the direction of the arrows to remove the battery cartridge cover Release button 1 Battery cartridge cover 3 Pull up the battery pull strap to remove the battery cartridge s Battery cartridge Battery pull strap 153 4 Pull the lock of the inside cover to the right and towards you to release it i cover Inside cover 5 Insert a Compact Flash card into the slot with the connector facing the slot and with the top facing down Compact Flash card with the top facing down 154 Appendices To remove the Compact Flash card press the card release button provided at the left of the card as shown below Compact Flash card Card release button 6 Set the inside cover so that its lock and pawl become fitted between the printed circuit boards r Lock 155 7 Push the battery cartridge into the BHT The end of the battery pull strap should come out from the left edge of the battery cartridge Z Battery cartridge Battery pull strap 8 Set the batte
34. DENSO Bar Code Handy Terninal BHF202B C E 202EV CE User s Manual If you leave the BHT with the battery cartridge discharged or with no battery cartridge loaded or if you replace the battery cartridge in a wrong way the BHT may lose the data stored in it Before cold booting refer to Chapter 2 Section 2 3 5 Warm and Cold Booting it is recommended that important data be saved into the FLASH folder or uploaded to the host computer Cold booting will erase all data stored in the RAM m DENSO WAVE INCORPORATED does not assume any product liability arising out of or in connection with the application or use of any product circuit or application described herein E If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact repairs will be made at a reasonable charge even within the warranty period E Intellectual Property Precaution DENSO WAVE INCORPORATED DENSO WAVE takes reasonable precautions to ensure its products do not infringe upon any patent of other intellectual property rights of other s but DENSO WAVE cannot be responsible for any patent or other intellectual property right infringement s or violation s which arise from i the use of DENSO WAVE s product s in connection or in combination with other component s product s data processing system s or equipment or software not supplied from DENSO WAVE ii the use of DENSO
35. WAVE s products in a manner for which the same were not intended nor designed or iii any modification of DENSO WAVE s products by other s than DENSO WAVE m Limited Warranty on Software Products In no event will DENSO WAVE INCORPORATED be liable for direct indirect special incidental or consequential damages including imaginary profits or damages resulting from interruption of operation or loss of business information resulting from any defect in the software or its documentation or resulting from inability to apply the software or its documentation Copyright DENSO WAVE INCORPORATED 2006 All rights reserved No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher Specifications are subject to change without prior notice All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders The latest precision manufacturing technology yields LCD panels whose pixels are 99 99 defect free The downside note is that up to 0 01 of the pixels can remain permanently dark or lit on today s state of the art panels A thin Newton s rings rainbow like patterns may appear on the touch screen This does not necessarily indicate a problem with the touch screen US and Canada Regulations This device complies with Part 15 of the FCC Rules Canadian ICES 003 and RSS 210 Rules Operation is subjec
36. WITH OPTICAL NST RENTS CLASS PA LISER PREDICT Ink BAXIMI UTP Sn LASER TeC60B 25 1 1995442 2001 Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure 9S e Do not look into the light source through the reading window or point the light source towards the eyes The light emitted through the reading window is harmful to the eyes e Do not poke at the eyes with the stylus that comes with the BHT N WARNING Handling the CU e If smoke abnormal odors or noises come from the CU immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer Failure to do so could cause fire or electrical shock If foreign material or water gets into the CU immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer Failure to do so could cause fire or electrical shock If you drop the CU so as to damage its housing immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer Failure to do so could cause fire or electrical shock Never use the CU for charging anything other than the specified battery cartridges Doing so could cause heat battery rupture or fire Never bring any metals into contact with the output terminals S Doing so could produce a large current through the CU resulting in heat or fi
37. aisha The screen on the left displays if a wireless local area network wireless LAN environment has not yet been established following purchase of the BHT unit BHT 202BW CE only If this screen does not display double tap the Wireless Zero Configuration status icon in the task tray to display Wireless Zero Configuration status J3 Indicates that the Wireless Zero Configuration WZC radio is connected to a wireless network 4 Indicates that the Wireless Zero Configuration WZC radio is not connected to a wireless network Synchronization state T Displays when the wireless device is open T T Shows the radio field intensity with the number of bars Til The WZC menu has the following tabs m P Information Displays information such as the IP address m Wireless Information Used to perform wireless communication settings The radio field intensity icons M Tu and Til indicate that the radio link is established but do not assure you that there will be few communications errors 107 E IP Information THALAMH Tapping the IP Information tab on the WZC Menu displays the screen shown at left Internet Protocol TCP IP settings information displays at this menu Renew Updates with the latest information Details Displays detailed information Tapping the Details button on the IP Information tab displays the screen shown at left Displays detailed information for the network settings Physical A
38. arc lamp ITF conforming to the UPC Shipping Container Code Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 1 0 magnification 3 Under the following conditions Ambient illuminance 500 Ix Xenon arc lamp Code 39 20 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 4 Under the following conditions Ambient illuminance 500 Ix Xenon arc lamp Code 39 20 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 149 Connector Interface Specification USB1 1 Full speed compliant RS 232C interface Connector TCX3171 HOSIDEN Pin assignment See below Pin 8 Pin 7 Pin No Signal name Data direction 1 GND 2 D USB Input Output 3 D USB Input Output 4 VBUS USB 5 CTS RS 232C Input 6 RxD RS 232C Input 7 RTS RS 232C Output 8 TxD RS 232C Output Note 1 The input output direction is stipulated from the BHT side 2 Use the exclusive cable only Wireless Interface BHT 202BW CE only Specification Spread Spectrum Direct Sequence Spread Spectrum Standards RCR STD 33 ARIB STD T66 Radio frequency 2400 to 2497MHz Transmission speed 11Mbps 5 5Mbps 2Mbps 1 Mbps Channel s 14 150 Appendices A 2 CU 200 1 Product Spec
39. ate Time Properties window appears You can specify the date time and time zone NOTE The entry range to the year is 2003 to 2099 Tree AATED Paii Time UE k Ca Input Panel Properties On the Control Panel window double tap Input Panel and the Input Panel Properties window appears Tap the Options button to display the screen shown at left You can switch the input panel software keyboard between large and small keys HOTE Regardless of the setting made for Use gestures for the gt gestures are always active The Gesture refers to special stylus operations that enable special input on the software keyboard as shown at left 55 E Taskbar On the Start menu tap Settings Taskbar The Taskbar and Start Menu window appears Tap the General tab to display the screen shown at left You can customize the taskbar E Run On the Start menu tap Run and the screen shown at left appears You can run applications or open files 56 Chapter 2 Getting Started the BHT and System Menu 2 5 3 Operating in System Menu On the desktop double tap BhtShell System Menu starts up to display the following screen Systm Mor To run the items in System Menu tap the desired item or press the corresponding numerical key To quit System Menu tap the OK or xX button located in the top right corner of the window The keys below are so designed that the function of each key is consistent in eve
40. canning angle of the reading window or the distance from codes as shown at right and try it again Specular effects occur when the reflection of the light from the bar code becomes excessively strong This can easily happen when the reflecting surface is polished or covered with vinyl e The laser light indicates the scanning range as a guide The indicated scanning range will deviate a little bit from the actual one Keep the BHT so that the laser light comes to almost the center of the bar code height The bar code reading procedure may differ depending upon the application used so follow the application s manual al al Before reading labels clean them if stained Avoid using the BHT in direct sunlight The BHT might fail to read correctly To read bar codes on curved surfaces apply the bar code reading window to the center of each bar code at a right angle If you pull the bar code reading window away from bar codes the actual scanning range will become narrower than the range covered by the illumination LED Do not use the BHT in the vicinity of radio equipment The BHT may malfunction The light intensity of the laser light or illumination LED will vary depending upon the scanning conditions and variation of its elements By using the KbifCE utility software codes read by the BHT can be converted into keyboard data to be transmitted to an application program The utility software can be downloaded from our
41. cations environment setup of the host computer E Problem The communications port has been already opened E Solution Close the communications port already opened for other processing and then retry the upload 67 E Problem Timeout has occurred E Solution Confirm the communications environment settings and communications log then retry the upload It is also necessary to check the communications environment setup of the host computer E Problem No file has been correctly selected for uploading E Solution Select a file s to be uploaded and retry the upload 68 Chapter 2 Getting Started the BHT and System Menu 2 2 ActiveSync Infrared Choosing 2 ActiveSync Infrared on the Communication menu connects the BHT to the host computer via the IrDA interface port Upon completion of connection the screen shown at left appears For details about the configuration of the host computer and connection using ActiveSync refer to Chapter 3 Section 3 5 ActiveSync Se Correcting tn Host ee OE anol Cone On _ Creel When connecting the BHT to the host computer using ActiveSync Infrared arrange the BHT and host computer with their IrDA ports facing directly each other When the CU 201 with RS 232C interface is used to connect the BHT with the host no ActiveSync can be used E TIP The BHT can be setup so that ActiveSync which allows connection with the host computer begins automat
42. ce e RS 232C interface cable option Connects the CU 200 and the host computer e USB interface cable option Connects the CU 221 and the host computer Connector interface cable USB cable connection between the BHT and host computer is also possible As an application development tool Microsoft eMbedded Visual C Service Pack 4 or later Microsoft Visual Studio NET or Microsoft Visual Studio NET 2003 should be used System Configuration Communications System Host computer IrDA BHT communication USB interface 2555 Connector interface IrDA communication RS 232C CU 201 or USB CU 221 interface CU 200 option yj option Chapter 2 Getting Started the BHT and System Menu In addition the BHT 202BW CE may operate in a radio communications system spread spectrum communication by connecting with access points by a wireless local area network wireless LAN e Access point Wireless communications base unit for the BHT Radio Communications System available with the BHT 202BW CE onl Host computer Access point f Roaming function p Ethernet 10BASE T Access point E CU 201 and RS 232C Interface Cable option The CU 201 is an IrDA compliant communications unit which is required when your host computer is not equipped with an IrDA interface port The CU 200 exchanges data and programs with the BHT optically and with the host computer via the RS 232C inte
43. ct while touching the LCD Functionally equivalent to drag with a mouse on a PC 1 3 Setting the Backlight Pressing the right hand trigger switch M4 key with the SF ALP key held down activates or deactivates the backlight function Backlight Off or Dim The backlight function is Disable when you turn the BHT power on Press the right hand trigger switch while holding down SF ALP Right hand trigger switch M4 Backlight On Press the i right hand trigger Hosa fs 3 switch while seconds holding down SF ALP Ea Fae Be oe SF ALP key a n A E z 7 btu Ba bfi i lime fp Se win raaj j Press any key except for the Frey ii simultaneous depression of the right hand trigger switch and SF ALE or tap the screen tiy Bee EI i Backlight Off or Dim The backlight function is Enable Press the right hand trigger switch while holding down SF ALP For one minute if the BHT is placed on the CU NOTE In user programs you can select the key to be used for activating or deactivating the backlight function instead of the initial setting combination of SF ALP key and right hand trigger switch M4 as well as modifying the on duration of the backlight before the automatic turning off TIP You can enable or disable the backlight function on the Backlight menu instead of pressing the backlight function on off key Chapter
44. ddress Displays the MAC address for the BHT internal Network Interface Card laina 4 imema IHRE IP Address Displays the IP address ri Berar T a re Subnet Mask Displays the subnet mask address Default Gateway Displays the default gateway address DHCP Server Displays the DHCP server address Lease Obtained Displays the time and date at which the IP address was obtained from the DHCP server Lease Expires Displays the time and date at which the IP Address became invalid DNS Servers Displays the DNS servers address WINS Servers Displays the WINS servers address Please refer to section 2 5 4 Detailed Description of the Functions in System Menu 3 8 Radio Frequency for details of settings for the IP address and so forth 108 E Wireless Information Wireless Properties HE 1 PALA T The n an a pea pas me rer Matai jei kg f E Tha hoy cn stony C Enable S00 LY authenhoraorn Ee ypa ie Elimeen Pmj Suet Chapter 2 Getting Started the BHT and System Menu Tapping the Wireless Information tab on the WZC Menu displays the screen shown at left The SSID list for which a search was performed automatically by the BHT displays If automatic recognition is not made double tap Add New and manually input the SSID Please refer to section 3 1 2 RF Related Parameters for further details on the SSID Tap the SSID for which a connection is to be made from the SSID list
45. desired file s in the Windows favorites folder E Documents On the Start menu tap Documents Recently opened documents appear To add files to the Start menu use the standard API SHAddToRecentDocs For details about SHAddToRecentDocs refer to the Help of application development tools E Control Panel On the Start menu tap Settings Control Panel BA The screen shown at left appears Les BHT You can configure the basic Windows operating environments in your pi BHT Beh Canea Cene b amp pE Eton 47 Backlight Properties On the Control Panel window double tap Backlight and the Backlight Properties window appears Biy FF Sf Erato Fo 3 een Backlight function Enable or disable the backlight function If it is enabled the backlight comes on when you press any key or tap the touch screen Backlight On duration Set the ON duration of the backlight that comes on when you press any key or tap the touch screen Battery Power ON duration when the BHT is not placed on the CU External Power ON duration when the BHT is placed on the CU Brightness Level Select the desired brightness level from the following four choices Dark Off T Low Bright o Mid Bright o High Bright L Bright Power Save Mode Change the settings for turning off the backlight after the BHT has not been used for a specified period of time Off The backlight turns off immediately Dim Th
46. details aspx displaylang en amp FamilylID 1dacdb3d 50d1 41b2 a107 fa75ae960856 Service Pack 4 http www microsoft com downloads details aspx displaylang en amp FamilyID 4A4ED1F4 91D3 4DB E 986E A812984318E5 APIs available for application development tools are Win32API Microsoft Foundation Class MFC Dedicated APIs for device control or data entry from the BHT When using Microsoft Visual Studio NET or Microsoft Visual Studio NET 2003 refer to the BHT 200 CE Class Library Reference Manual E Software Development Kit BHT 200 Software Development Kit named BHT200_XXXXXX msi XXXXXX version This is a library to be embedded into application development tools for developing applications for the BHT 202BW CE For details about the BHT 200 Software Development Kit refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual 15 2 2 Components 2 2 1 Names and Functions Provided on the BHT 202BW CE Synchronization LED Indicator LED Flashes during wireless j __llluminates in blue when the BHT has successfully read a bar code communication i Ch LED arge Built in antenna i llluminates in red during charging and turns green at Do not cover this j completion of charging antenna section fi Touch screen LCD liquid crystal display with ae l Shows the characters and graphic patterns SPE a ape You may directly tap the screen
47. e BHT NOTE Before using the CU 221 you need to install the dedicated USB device driver stored in the CD ROM that comes with the CU 221 For the installation uninstallation procedure refer to the guidebook that comes with the CU 221 135 5 2 Components and Functions IrDA interface port Used to exchange data Status indicators i optically with the BHT POWER LED green Lights when the power is applied to the CU 4 f M BHT charge terminals Do not stain these terminals doing so could result in a lower charging efficiency DATA Communications LED green Lights when the BHT is communicating with the host PC Interface connector Used to exchange data with the host PC or communications station The CU 201 221 has an RS 232C port or USB port respectively DIP switch Provided on CU 201 Used to set the CU s transmission speed Power inlet connector Plug the dedicated AC adapter into this connector Without connecting the AC adapter the CU 221 can work if the power 5 V 500 mA is supplied via the USB host or USB hub 136 Chapter 5 Handling the CU 200 Option 5 3 Applying Power to the CU 200 CU 201 The CU 201 should be powered from a wall socket via the dedicated AC adapter Connect the outlet plug of the AC adapter to the power inlet connector of the CU 201 then plug the other end into a wall socket CU 221 The CU 221 should be powered from a wall socket via the dedicated AC adapter or from
48. e backlight remains on very dimly 1 Pressing the backlight function on off key the initial setting the simultaneous depression of the SF key and right hand trigger switch M4 key toggles between enabled and disabled states regardless of the backlight function setting made on this screen 48 Chapter 2 Getting Started the BHT and System Menu BHTSeitings On the Control Panel window double tap BHTSettings and the BHTSettings window appears For details refer to Section 2 5 4 3 System Properties Menu System Properties On the Control Panel window double tap System and the System Properties window appears Tap the General tab to display the screen shown at left Choose the Memory tab to display the screen shown at left You can check the memory allocation and the free space of the RAM You can also change the memory allocation by moving the slider NOTE According to your operating requirements assign the memory between Storage memory and Program memory Depending upon the memory allocation e g insufficient program execution space the BHT might not operate normally 49 Stylus Properties On the Control Panel window double tap Stylus and the Stylus Properties window appears You can adjust the double tap speed Tap the Calibration tab to display the window shown at left To chart the mcdiraion proces tat Near aha Craik cree ord iak cd ts Tab the Recalibrate to display the
49. e button to delete that SSID from the list Try network connections shown on the Preferred Networks display from the SSID at the top Automatically connect to non preferred networks Select this check box to display accessible non preferred networks enabling a selection to be made Networks to access Used to select a network filter All available Both of following Only access points Between BHT and access point Only computer to computer Between BHT and other device If the Automatically connect to non preferred networks check box is selected this is applicable to both preferred networks and non preferred networks If the check box is not selected it is applicable between preferred networks only Wireless Networking Log Tapping the Log button on the Wireless Information tab calls up the Wireless networking Log The wireless networking log displays 112 Chapter 3 Communications Operations of the BHT 202B CE 202BW CE Describes the communications operations of the BHT the spread spectrum communication BHT 202BW CE only infrared communication USB interface specifications connector interface specifications basic communications specifications communication using Ymodem and ActiveSync for data transfer with the host computer or other devices 3 1 Spread Spectrum Communication esis A SA a he ea ee eds a 114 3 1 1 Notes for Wireless Operations siuii aa cto eel eee adada
50. e key is provided V y automatically Enable 802 1X x xi y p P 5 authentication EAP type PEAP TLS PEAP TLS Note No entry possible vV Select No entry or no selection XXXXxxX Enter the network key 110 Chapter 2 Getting Started the BHT and System Menu e Settings when PEAP TLS Selected for EAP Type Tapping the Properties button on the Wireless Properties window displays the screen shown at left Displays the User Certificate issuance information Select the Validate Server check box to enable the certificate server Default Enabled When TLS is selected for the EAP type tapping the Select button on the Authentication Settings window displays the screen shown at left Tho Vidi R you mami jo apa hapasta hd ate The Certificates list displays Tap a certificate from the list and then tap the View Certificate button to display detailed information 111 Advanced Wireless Settings Tap the Advanced button from the Wireless Information tab to display the screen on the left Use Windows to configure my wireless settings Select this check box to automatically perform wireless network settings at Windows CE This check box should always be selected Preferred Networks Displays the Preferred networks SSID list Tap an SSID and then tap either the Up or Down button to change the order in which the SSID displays in the list Tap an SSID and then tap the Delet
51. eeeeeaesaeseeesaeseneeaeseeesaeseeeeaeeaeseeeeaeeaees 4 1 8 Setting the Backlight cas2nsisi aed een ai at isc i ae ee Ae AS 6 1 4 USING The Keypad isminin a eaae A Aa A AYE SEa N ANC 7 15 Transfering Datars ssc iisceecsschiscesvecinscvsescctectessi use dessecusatcdassvvsesedaevishostesva ciesudesvudvevts castes sdeiseatsdessudverttvscsscutvatarnsees 8 1 1 Reading Bar Codes Turn the BHT on bring the bar code reading window to the bar code to be scanned and press the trigger switch Pressing the trigger switch halfway emits a laser light to indicate the scanning range and pressing it fully turns on the illumination LED to scan the bar code When the BHT has read the bar code successfully the indicator LED will illuminate in blue Bar code scanning range indicated by Max 70 cm 27 6 the laser light erie a e Indicator LED i ay gt Power key Iluminates in blue when the Ne A P BHT has successfully read the E 3 bar code Trigger switch M4 key Trigger switch M3 key ai E Grip style BHT Bar code scanning range indicated by the laser light Indicator LED llluminates in blue when the BHT has successfully read the bar code Trigger switch _ The BHT can read bar codes at a maximum distance of 70 cm 27 6 from the reading window For details about the scanning conditions refer to Appendix A Chapter 1 Quick Guide e If the BHT fails to read due to specular effects or other factors change the s
52. eiver 3 2 Interface circuit RS 232C Output circuit Input circuit TxD RTS RxD CTS _ 5kQ Signal Level Output voltage H 3 KQ load sv tv Output voltage L 3 KQ load tsv sv NOTE 1 Input Output voltage are specified at the terminal of the interface connector 2 Output voltage becomes unsettled when the connector communication device file is closed 3 Output voltage shall be under the following conditions Power voltage Rated voltage Load resistance 3 KQ 119 3 4 Basic Communications Specifications and Ymodem 3 4 1 Basic Communications Specifications Listed below are the communications specifications when the BHT exchanges data with a host computer through the CU 200 IrDA interface or the connector interface IrDA Interface Connector Interface Synchronization Start stop Transmission Speed 2400 9600 19200 38400 300 600 1200 2400 4800 9600 57600 or 115200 bps 19200 38400 57600 or 115200 bps Transmission Code ASCII 8 bit code ASCII 7 bit or 8 bit code Transmission Bit Order LSB Least significant bit first Vertical Parity None Even odd or none E Synchronization For accurate data transaction it is very important to synchronize the transmission between the sender and receiver To do this it is required to previously define the bit order and position the character length and the beginning and end of
53. er switches M3 M4 2 Magic keys M1 M2 2 Numerical keys and others 22 Display Type Touch screen dot matrix TFT liquid crystal display LCD with backlight Formation 240 dots wide by 320 dots high Calendar Clock Year month day hour minute and second Year Two digits with auto correction on February 29 Reading Confirmation Indicator LED Red amp blue beeper and vibrator 147 2 Bar Code Specifications 1 Available Bar Code Types Bar code type Bar dimensions Readable magnification Universal product codes N EAN 13 EAN 8 UPC A UPC E 0 26 mm min 0 8 min EAN 13 with add on EAN 8 with add on UPC A with add on UPC E with add on 2 digits add on 5 digits add on Interleaved 2of5 ITF Standard 2of5 STF Codabar NW 7 Code 39 Code 93 Code 128 EAN 128 10 24 mils min 1 0 15 mm min 5 91 mils min PCS value 20 45 2 Optical Properties Required White bars Reflection intensity 45 min Black bars Reflection intensity 25 max PCS value 0 45 min 148 Appendices 3 Bar Code Label Size Recommended width 10mm min 0 39 inch min Length Depth of field Distance from bar codes to the reading window 700 mm 27 56 inches Length of labels including margins 400 mm max 15 75 inches max Minimum narrow bar width 0 635 mm min Langlht K gt mee T UAA NA 4 Thickness of Bars and Depth of Field Minimum narrow bar
54. ervance of these warnings and cautions is a MUST for preventing accidents that could result in bodily injury and substantial property damage Make sure you fully understand all definitions of these terms and symbols given below before you proceed to the text itself A WARNING Alerts you to those conditions that could cause serious bodily injury or death if the instructions are not followed correctly CAUTION Alerts you to those conditions that could cause minor bodily injury or substantial property damage if the instructions are not followed correctly Meaning of Symbols Atriangle 4 with a picture inside alerts you to a warning of danger Here you see the warning AEN for electrical shock A diagonal line through a circle alerts you to something you should not do it may or may not have a picture inside Here you see a screwdriver inside the circle meaning that you should not disassemble A black circle with a picture inside alerts you to something you MUST do This example m shows that you MUST unplug the power cord N WARNING Handling the battery cartridge 9 e Never disassemble or heat the battery cartridge nor put it into fire or water doing so could cause battery rupture or leakage of battery fluid resulting in a fire or bodily injury Do not carry or store the battery cartridge together with metallic ball point pens necklaces coins hairpins etc Doing so could short circuit the terminal pins causin
55. es to the suspend mode when the CU 221 is charging the battery cartridge then the CU 221 stops charging When the host PC recovers from suspend mode the CU 221 starts charging again To prevent the CU 221 from getting affected by suspend mode use the dedicated AC adapter 143 5 6 Interface Specifications 1 Interface Connector and Pin Assignment CU 201 The CU 201 has an RS 232C interface port Dsub 9P RS 232C interface port Dsub 9P on the CU 201 Signal Input Output Pin No Signal Functions CU201 Eeamaraevios 2 RD Receive data lt 3 SD Send data gt 4 ER Data terminal equipment ready gt 5 SG Signal ground 6 DR Data set ready 7 RS Request to send 8 CS Ready to send The input output voltage threshold for the logical valued signal is listed below Logical Value Input Voltage Threshold Output Voltage Threshold 0 3V lt n lt 15V 5V min 1 15V lt n lt 3V 5V max CU 221 The CU 221 has a Full Speed USB 1 1 capable port Series B receptacle 144 Chapter 5 Handling the CU 200 Option 2 Interface Cable Connection CU 201 As illustrated below connect the CU 201 on which the BHT is put to a host PC with a cross mode cable To connect it to a modem use a straight mode cable CU 201 Host PC DTE DTE cD Ril Cable Connection between CU 201 and Host PC CU 201 Modem OE ee GE FD ER OR i RS cs Ba Goan bh g BS a
56. for the period specified by Interval and then send an echo request again For Type 1 the relationship between the Interval and Timeout should be Interval gt Timeout Sends an echo request 1 _ Cl Receives an echo reply lt _ ees period Interval Sends an echo request _ gt e Type2 After sending an echo request Ping will wait for an echo reply to be received or for timeout to occur After that Ping will wait for the period specified by Interval and then send an echo request again For Type 2 no relationship between the Interval and Timeout is required If Ping receives an echo reply Sends an echo request _ gt Receives an echo reply lt Interval Sends an echo request _ gt If timeout occurs Sends an echo request _ gt Timeout period Timeout occurs lt _ Interval Sends an echo request 1 gt 92 Chapter 2 Getting Started the BHT and System Menu E Backup Battery Discharge Counter On the System Properties Menu pressing the 0 key with the SF ALP SF key held down calls up the screen shown at left This screen displays the discharge count of the backup battery If you replace the backup battery tap the Reset button to reset the discharge counter to zero NOTE Only after the discharge count reaches 200 the counter can be reset to zero stat fae Em E Act
57. ft where the current communications link status appears in orninn iid real time Pete tae ee Associated Access Point Displays the MAC address assigned to the wireless interface of the associated access point Signal Strength Displays the signal intensity of receive packets Beacons Received Displays the progress bar that shows the percentage of received beacon packets relative to those to be received Beacon Synchronous signals transmitted periodically from the access point Link Quality Displays the comprehensive link operation level with the access point If the following shows Communications state Excellent Excellent communications link Good i Fair Poor Poor communications link Not Associated Not associated with an access point Link Speed Displays the current transmission speed Channel Displays the current communications channel TIP Tapping the Link tab when the RF device is not opened automatically opens the RF device and displays the current communications link status 90 Chapter 2 Getting Started the BHT and System Menu E Testing with Ping MIC Contred Tapping the Ping tab on the NIC Control menu displays the screen D cpeen wer ure Pre shown at left Bes iP Dein fe Dest IP Specify the IP address of a host computer that i peel T you want to ping Treue fio Data size Specify the data size of an echo request pana Interval Specify the echo request intervals in
58. ftware keyboard You can display or hide the software keyboard by tapping the software keyboard status icon on the task tray Software keyboard Lie K Software keyboard status icon Just as from the hardware keyboard you can enter data from the software keyboard by tapping keys on it 1 5 Transferring Data E Using radio link BHT 202BW CE only Using radio waves the BHT 202BW CE may transfer data to an access point in a spread spectrum communications system NOTE If there are too many communications errors first make sure that the BHT 202BW CE points directly _ atan access point Host computer Built in antenna Access point For data transfer using radio link it is necessary to configure a wireless local area network wireless LAN connecting the BHT 202BW CE and access points Chapter 1 Quick Guide E Using infrared link Using infrared rays the BHT may transfer data directly to the host computer equipped with an IrDA interface port and other IrDA compliant devices e Make sure that there is no obstruction in the light path between the BHT and any target stations In infrared communication you need to keep the BHT and any target stations within the effective infrared radiation range usually 15 cm 5 9 e Shield the IrDA interface from direct sunlight ambient intense lighting inverter driven fluorescent lighting in particular and other potential sources of infrared radiation Sources to watch out f
59. g the batteries to rupture or the battery fluid to leak resulting in a fire or bodily injury Avoid dropping the battery cartridge or letting it undergo any shock or impact Doing so could cause the batteries to break generate heat rupture or burn Never charge the rechargeable battery cartridge where any inflammable gases may be emitted doing so could cause fire Q Only use the dedicated charger CU 200 CH 201 for charging the rechargeable battery cartridge Using a different type of charger could cause battery rupture or leakage of battery fluid and result in a fire bodily injury or serious damage to property Handling the BHT e The BHT uses a laser light for indicating the scanning range The intensity of the laser light might be too low to inflict bodily injury However do not look into the laser beam or view directly with optical instruments The BHT complies with IEC 60825 1 1993 A2 2001 In accordance with Clause 8 and 9 IEC 60825 1 the following information is provided to the user For USA and Canada LTH 21 CER 1040 10 AND 1040 11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE Ne 30 DATED JULY 26 2001 LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 2M LASER PRODUCT TIGW DA NGT STARE INIO BEAK H OPTICAL INSTRUMENTS i MATHUK OUTPUT ES0N8 LASER LASER RADIAT IAN TA WAT STARE INIO Bae AR VIEN DIRECTLY
60. her The effective IR range and IR port angle may differ depending upon the target equipment so observe the instructions given in manuals furnished with such equipment NOTE If IR transfer fails bring the BHT closer to the target station or change the IR port angle and try gt again The BHT s IR communications device is IrDA compliant IrDA stands for Infrared Data Association which has defined hardware IrDA Serial Infrared Physical Layer Link and communications protocols for IR communications The BHT s physical layer complies with the IrDA1 2 with a maximum transfer distance of 0 15 m 5 9 inches and maximum transmission rate of 115 2 kbits per second 117 3 3 Connector interface specification The BHT 202BW CE is equipped with a USB interface for interfacing with the host PC and with a connector interface for communicating with the host PC 1 Specification e USB1 1 Full soeed compliant e RS 232C interface 2 Connector TCX3171 HOSIDEN Pin 8 Pin 2 Pin 7 Pin 1 Pin No Signal name Data direction 1 GND 2 D USB Input Output 3 D USB Input Output 4 VBUS USB 5 CTS RS 232C Input 6 RxD RS 232C Input 7 RTS RS 232C Output 8 TxD RS 232C Output Note 1 The input output direction is stipulated from the BHT side 2 Use the exclusive cable only 118 Chapter 3 Communications Operations of BHT 202B CE 202B W CE 3 1 Interface circuit USB USB Driver Rec
61. ically if the BHT is placed on the CU 221 while turned on For further details refer to Section 2 5 4 3 System Properties Menu lf ActiveSync connection succeeds Carica ior If ActiveSync connection succeeds the BHT beeps once and displays the ActiveSync icon circled in red at left in the task tray If ActiveSync connection fails If ActiveSync connection fails the BHT beeps once and does not display the ActiveSync icon 69 2 3 ActiveSync Serial Choosing 3 ActiveSync Serial on the Communication menu connects the BHT to the host computer via the connector interface port After a connection is established the screen shown at left appears For details about the configuration of the host computer and connection using ActiveSync refer to Chapter 3 Section 3 5 ActiveSync If ActiveSync connection succeeds If ActiveSync connection succeeds the BHT beeps once and displays the ActiveSync icon circled in red at left in the task tray If ActiveSync connection fails If ActiveSync connection fails the BHT beeps once and does not display the ActiveSync icon 70 Chapter 2 Getting Started the BHT and System Menu 2 4 ActiveSync USB Choosing 4 ActiveSync USB on the Communication menu connects the BHT to the host computer via the USB interface port Upon completion of connection the screen shown at left appears For details about the configuration of the host computer and connection
62. ifications CU 201 CU 221 Power Source 100 to 240 VAC 50 60 Hz 0 2 A Supplied via the USB cable 5 VDC Use AC adapter Power Consumption 5 VDC 1500 mA 5 VDC 500 mA AC adapter output Dimensions W x L x H 114 x 140 x 87 mm 114 x 134 x 87 mm 4 49 x 5 51 x 3 43 inches 4 49 x 5 27 x 3 43 inches Weight Approx 210 g Approx 7 41 oz Operating Ambient Temperature 0 C to 40 C 32 F to 104 F Operating Humidity 20 to 80 with no dew condensation NOTE Can be powered from a wall socket via the dedicated AC adapter 2 Charging Requirements CU 201 CU 221 When using the AC adapter Charge current Approx 790 mA Charge time Approx 3 hours approx 5 5 hours CU 221 When powered via the USB cable Charge current Approx 210 mA Charge time Approx 9 hours approx 21 hours For grip style BHTs with two battery cartridges loaded 151 3 Interface Specifications CU 201 RS 232C interface port Dsub 9P on the CU 201 Signal Input Output Pin No Signal Functions CU 201 External device 2 RD Receive data lt 3 SD Send data gt 4 ER Data terminal equipment ready gt 5 SG Signal ground 6 DR Data set ready 7 RS Request to send 8 CS Ready to send WOTE Shown below is a diagram of the internal connection in the CU 201 Hosi camputer modem or otter devices CU 201 Signal rica Ho DUA Interfaces RD 2 I rsa ADA Oooo ie E interface Dormin
63. ith an even parity and a single bit each for start and stop bits LSB MSB 1 0 g p D a 1 a 0 Ss i en cs i Start bit Sipp bit Parity bat E Vertical Parity A vertical parity bit is a redundancy bit which is added to every character to be transmitted in order to check that data has been transmitted accurately The parity bit should be set to 1 or 0 depending upon the parity parameter setting to make the number of set bits in the character even or odd The receiver counts the number of set bits in the transmitted character code to make sure that it has the selected number even or odd of set bits The vertical parity bit is positioned immediately following the MSB Most significant bit as shown below LSB MSB bO b1 b2 b3 b4 b6 io ai For 7 bit data Vertical parity bit LSB MSB bO b1 b2 b3 b4 b6 b7 io a For 8 bit data Vertical parity bit 121 3 4 2 Using Ymodem In System Menu and user programs the BHT can use the Ymodem protocol with the following communications parameters Port IrDA interface Connector interface Transmission Speed 2400 9600 19200 38400 300 600 1200 2400 4800 9600 57600 or 115200 bps 19200 38400 57600 or 115200 bps Character Length 8 bits 8 bits Vertical Parity None Even odd or none Stop Bit Length 1 bit 1 or 2 bits In System Mode Refer to Section 2 5 4 2 Communication Menu In User P
64. iveSync automatic connection On the System Properties Menu pressing the 1 key with the SF ALP SF key held down calls up the screen shown at left On the ActiveSync page select Infrared or USB in the Automatic Connection group box Infrared Turns on automatic connection via the infrared port USB Turns on automatic connection via the USB port Tapping the OK button validates the setting The CU 221 is needed TI P Automatic connection is disabled by default 93 4 Test Menu Choosing 4 Test in System Menu calls up the screen shown at left 1 BARCODE Select the bar code reading test 2 BEEPER Select the beeper scale test 3 AGING Select the aging test 4 COM Select the communications test 5 DISPLAY Select the LCD and indicator LED 6 KEY VIBRATION Select the key entry and vibrator test Seat le ie NOTE If an error occurs in any of the above tests contact your nearest dealer 94 Chapter 2 Getting Started the BHT and System Menu 4 1 Bar code reading test Selecting 1 BARCODE on the Hard Test menu calls up the screen shown at left Actually read bar codes with the BHT and check that the barcode data read matches ones displayed on the LCD fale m Bar code type Number of digits of the bar code Data read fealeCODE TES Upon completion of bar code reading the BHT beeps once turns on the indicator LED in blue and displays the read data together with
65. ize the memory including the Registry but excluding files stored in the FLASH folder Initializing procedure 1 Tap the Initialize tab and select the RAM radio button 2 Select the Initialize Registry check box 3 Tap the Initialize button ai oe U f Select No 4 To initialize the memory tap the Yes button to return to the previous menu tap the No button After the BHT displays the screen shown at left for a few seconds it will automatically reboot 79 E Initializing the FLASH folder You can erase all information stored in the FLASH folder and let the folder revert to the initial state Initializing procedure 1 Tap the Initialize tab and select the FLASH radio button 2 Tap the Initialize button i U fl Select No 3 To initialize the memory tap the Yes button to return to the previous menu tap the No button Upon completion of initialization it will take approx one minute the screen shown at left appears 80 Chapter 2 Getting Started the BHT and System Menu E Running Scandisk through the FLASH folder If the power to the BHT is shut down when the FLASH folder is being accessed some broken file fragments may remain in the FLASH folder so that the free memory space will be decreased To remove or clear those fragments run Scandisk through the FLASH folder Initializing procedure 1 Tap the Scandisk tab and select the Scandisk button li U f Select No 2 To
66. l value is from 1 to 9 and the default is 4 MARKER You can select the marker ON OFF mode from the following Normal Normal mode driven by the trigger switch None OFF mode In Normal mode the marker comes on at the same time as the illumination LED does Minimum number of digits to be read for ITF STF or CODABAR You can set the minimum number of digits to be read for ITF STF and CODABAR Setting a small number of digits increases the frequency of digit missing reading or misreading depending upon how to scan bar codes or the quality of bar codes On the other hand setting a large number will diminish the possibility of those errors The setting range is from 2 to 20 for ITF from 1 to 20 for STF and from 3 to 20 for CODABAR The default is 4 for ITF and CODABAR and 3 for STF 75 3 2 Beeper Vibration Arenas ibe ah Voter Rumble Desa ho na Ces Corr h Sia Haired hes iii oF Oah Chimi Some lao Cor Qem Wind Tipp bes cher oF Clow Les bpian boy cick aor Con Fanfa m Double tap the Beeper Vibration and the Beeper Vibration property appears On this menu you can adjust the beeper volume and switch the beeper and vibrator Adjusting the beeper volume ary ches Corr h Mi Leal Half oraat hire clic Sor Oh Clin Soe Loe Cor Oan Wibod Tipe bees cheers oF Clon Laser phang boy da Sor Corn Choose the Volume tab to display the screen shown at left where you can select the beeper vol
67. lication described herein E If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact repairs will be made at a reasonable charge even within the warranty period E Intellectual Property Precaution DENSO WAVE INCORPORATED DENSO WAVE takes reasonable precautions to ensure its products do not infringe upon any patent of other intellectual property rights of other s but DENSO WAVE cannot be responsible for any patent or other intellectual property right infringement s or violation s which arise from i the use of DENSO WAVE s product s in connection or in combination with other component s product s data processing system s or equipment or software not supplied from DENSO WAVE ii the use of DENSO WAVE s products in a manner for which the same were not intended nor designed or iii any modification of DENSO WAVE s products by other s than DENSO WAVE Chapter 1 Quick Guide Chapter 2 Getting Started the BHT and System Menu Chapter 3 Communications Operations of the BHT 202B CE 202BW CE Chapter 4 Error Messages Chapter 5 Handling the CU 200 Option Appendices Chapter 1 Quick Guide This chapter describes the basic operating method of the BHT and the related notes 1 1 Reading Bar C d Ssni naa r A ce ae eects Hire heed ek had ieee ey 2 1 2 Setting and Using the Hand Strap and Stylus eee eeeeeeeeeeeeeeceeeeeeseeeeee
68. m Tirani If the test ends due to a timeout error the tested slave BHT beeps three times and displays the screen as shown at left This sample screen shows that an error has occurred at 2400 bps If the test ends due to mismatch between the sent data and received data the tested slave BHT beeps three times and displays the screen as shown at left This sample screen shows that the received data is 196 although data 17 has been sent at 2400 bps 99 Testing the USB interface port Selecting the 2 USB on the COM menu calls up the screen shown at left and starts connecting with the host computer using ActiveSync For the configuration of the host computer and details about ActiveSync refer to Chapter 3 Section 3 5 ActiveSync lf ActiveSync connection succeeds via the USB interface port If ActiveSync connection succeeds the BHT beeps once and displays SELECT PORT l the ActiveSync icon circled in red at left in the task tray If ActiveSync connection fails via the USB interface port If ActiveSync connection fails the BHT beeps once and does not display the ActiveSync icon 100 Chapter 2 Getting Started the BHT and System Menu To terminate the USB interface test There are two ways to terminate the USB interface test Disconnect the USB interface cable and Disconnect the link with the button in the task tray as described below 1 Double tap the ActiveSync icon circled in red at left in the task
69. mable gases may be emitted doing so could cause fire A CAUTION e Do not use batteries or power sources other than the specified ones doing so could SQ generate heat or cause malfunction The BHT has an integrated backup power source which backs up the memory and calendar clock in the BHT when no battery cartridge is loaded or the voltage level of the battery cartridge drops below the specified level The backup power source is automatically charged by the battery cartridge When you first load the battery cartridge after purchase or you load it after leaving the BHT unused for a long time do not remove the battery cartridge for approx 48 hours after that loading This is for charging the memory backup source integrated in the BHT e Avoid storing the rechargeable battery cartridge in a hot place 50 C 122 F or higher The battery capacity may be decreased e Do not touch the charge terminals of the rechargeable battery cartridge or stain those terminals Doing so could result in a charging failure 25 E Battery Voltage Level on the Status Indicator Line The battery voltage level is always displayed on the status indicator line For details refer to Section 2 2 2 Status Indicators on the LCD E Low Battery Indication Low battery warning If the battery output voltage drops below a specified lower level limit when the BHT is in operation the BHT displays the following message for approx 2 seconds and beeps three ti
70. mes After that it will resume previous regular operation Battery voltage has lowered Solution The battery cartridge will need to be recharged before long Recharge or replace the battery cartridge as soon as possible Shutdown due to low battery If you continue to use the BHT without recharge or battery replacement after the message above appears the battery output level lowers to the extent the BHT can no longer operate The BHT displays the following message beeps five times and then turns itself off Depending upon the battery level the message may not appear or the beeper may not sound five times Charge the Battery Solution Recharge or replace the battery cartridge 26 Chapter 2 Getting Started the BHT and System Menu Grip style BHT As long as the voltage level of either one of battery cartridges loaded in the BHT body and grip is higher than the specified level no low battery messages will appear If any low battery message appears therefore you need to replace both battery cartridges Even if you only have one fully charged replacement battery cartridge on hand remove both batteries NOTE You may charge the rechargeable battery cartridge with the optional CU 200 communication unit or optional CH 201 charger For the charging procedure using the CU 200 refer to Chapter 5 For that using the CH 201 refer to the CH 201 User s Manual If the Charge the battery message appears after the BHT u
71. n on off key laser lighting key or trigger switch depending upon definition in System Menu or in user programs Although M3 to M5 are set as trigger switches by default user defined virtual key codes can be assigned to them ALP Alphabet key Pressing this key switches between the numeric entry and alphabet entry modes SF Shift key Used in combination with other keys for special input procedures C Clear key Pressing this key in BhtShell returns to the previous screen BS Backspace key Moves back one character Numerical keys ENT Enter key Used for data input Finalizes the input data or operations and starts the corresponding processing Provided on the Grip style BHT 19 2 2 2 Status Indicators on the LCD Windows desktop Windows desktop on 30 key pad type on 26 key pad type Status indicators Status indicators Battery voltage level Shows the current battery voltage level fm Displays when the voltage level is high Displays when the voltage level is low The grip style BHT shows two icons as shown below The upper one is for the battery cartridge loaded in the BHT body and the lower one for that in the grip raaa Voltage level in the BHT body Voltage level in the grip Tio The displayed battery level shows the terminal voltage of the battery cartridge not how much power is TIP left The battery voltage level varies depending upon the operation
72. ndergoes any shock or impact turn the power off and on and then check the battery output level The battery may not have run out AA WARNING e Only use the dedicated charger CU 200 or CH 201 for charging the rechargeable battery cartridge Using a different type of charger could cause battery rupture or leakage of battery fluid and result in a fire bodily injury or serious damage to property AN CAUTION e Never charge a wet or damp rechargeable battery cartridge Doing so could cause the batteries to break generate heat rupture or burn 27 2 3 2 Setting up 2 Calibrating the touch screen Press the power key to turn on the BHT The calibration screen appears so follow the on screen instructions If nothing appears first perform a cold boot refer to Section 2 3 5 ee The appears first at the center of the screen as shown at left acca laa Tap the center of the with the stylus for one second and the moves to the upper left Tap its center and it moves to the bottom left This way tapping the center of the moves it starting from the center of the screen to the upper left bottom left bottom right and upper right in this sequence During calibration the power key is disabled After completing the calibration press the power key a After completion of the above calibration press the ENT key or tap rava bear measure the screen The calendar clock setup screen will appear as shown eres belo
73. ndows Maa mma reo nap be aap er haragra mae Heer ra eda brene i Y rade pe seghi aran bier eee a pe et ee E E E PE ey ee eara Brar hi h i i ram Finnia ii aiiis alk mi ora eo The partnership between the BHT and host computer has been set up For instructions on how to use ActiveSync refer to its Help on the host computer a Click Finish to complete the setup and return to For debugging of user programs using ActiveSync refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual In spread spectrum communication BHT 200BW CE 201BW CE only Like ActiveSync in IrDA communication or USB communication ActiveSync in spread spectrum communication requires a partnership between the BHT and host computer to be set up Set up the partnership according to the operating procedure in IrDA communication or USB communication given on the previous page For the operating procedure of ActiveSync on the BHT refer to Chapter 2 Section 2 5 4 2 3 ActiveSync RF NOTE Depending upon the PC name e g the PC name begins with a numeral ActiveSync may not run in spread spectrum communication It is recommended that the PC name be set with alphabets A to Z and a to z only 128 Chapter 3 Communications Operations of BHT 202B CE 202BW CE 129 Chapter 4 Error Messages This chapter lists the error messages which will appear on the LCD if some error occurs in the BHT 4
74. ni Maranon On the desktop double tap Messenger The screen shown at left he appears tet as Siam E Microsoft WordPad On the desktop double tap Microsoft WordPad The screen shown at left appears 44 Chapter 2 Getting Started the BHT and System Menu E My Documents On the desktop double tap My Documents The screen shown at left appears With this program you can browse the file information in the BHT On the desktop double tap Remote Desktop Connection The screen shown at left appears 45 2 5 2 Start Menu Tap the Start button in the bottom left corner of the desktop The Start menu appears where you can run programs and make system settings On the Start menu tap Programs Communication Terminal The screen shown at left appears You can create a new session E Internet Explorer On the Start menu tap Programs Internet Explorer to run Internet Explorer For details refer to Section 2 5 1 Desk Top Internet Explorer E Windows Explorer On the Start menu tap Programs Windows Explorer to run Windows Explorer For details refer to Section 2 5 1 Desk Top My Device 46 Chapter 2 Getting Started the BHT and System Menu E Command Prompt On the Start menu tap Programs Command Prompt The screen shown at left appears E Favorites On the Start menu tap Favorites Your Favorites list appears To add items to your Favorites list create a shortcut s of the
75. nnection to the network cannot be completed the RF settings may have not been made correctly Check the RF settings again Upon completion of connection to the network the screen shown at left appears Select Network Connection as connection method and select the name of the host computer in the Connect to box Then tap the Connect button 72 Chapter 2 Getting Started the BHT and System Menu Upon completion of connection by ActiveSync the screen shown at left appears enade Fea If connection to the network fails If connection to the network fails the BHT beeps three times and displays the following screen E Solution The RF settings may have not been made correctly According to the procedure given in section 2 5 4 3 8 Radio Frequency make the correct RF settings lf no partnership has been set up If no partnership has been set up between the host computer and BHT the BHT beeps three times and displays the following screen E Solution Set up a partnership according to the procedure given in Section 3 5 2 Connection Using ActiveSync 73 3 System Properties Menu e pan wap al mh Loe j Pie Serie Pram Eir Er Tl PIT Aebi Dipi am 3 1 Barcode ROE Lew fa E PRE Presta TTR ETF Ponjo en 2 Choosing 3 System Properties in System Menu calls up the window shown at left 1 Barcode Opens the Barcode menu 2 Beeper Vibrati
76. nored If a backlight function on off key is not assigned to any of the M1 through M5 keys and halfway pressed M3 through M5 keys the combination of the SF ALP SF and M4 keys work as a backlight function on off key by default M5 key available on the grip style BHT User defined code file User defined virtual key codes can be assigned to magic keys Enter the desired virtual key codes into a text file and save it in the FLASH folder of the BHT with the filename MKeyDef txt P Sitey tel Mobrpadd The screen shown to the left is an example for adding ALT X and Ce Get Pome ier bee ALT Y ALT 2 Owl OeSe ALT 2 O812 GES The code file is read when the Key definition menu is started The defined key codes are displayed below Alternate in the same order as entered in the text file For further details refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual 85 3 7 Status Display Status Ceadip 3 8 Radio Frequency nin aak o omer Creer Waren Pier ramm Ton Jaan e Double tap the Status Display and the Status Display property appears You can display or hide the following status indicators in the task tray BATTERY Battery voltage level RF Synchronization state SIP Software input panel Software keyboard SHIFT Keypad shift state CPU STANDBY Standby state of the CPU ALPHA Alphabet entry mode status The default
77. ns environment settings and communications log then retry the download It is also necessary to check the communications environment setup of the host computer E Problem The communications port has been already opened E Solution Close the communications port already opened for other processing and then retry the download E Problem Timeout has occurred E Solution Confirm the communications environment settings and communications log then retry the download It is also necessary to check the communications environment setup of the host computer 65 E Uploading Specify a file you want to upload and then tap button 3 and the BHT waits for a file to be uploaded n N File you want to upload 2 dean H ml prin angen Fes Upon completion of uploading the BHT sounds a long beep once and displays the screen shown at left 66 Chapter 2 Getting Started the BHT and System Menu If an error occurs during uploading If some error occurs during uploading one of the following screens will appear and the beeper beeps three times ae fe COMM LIS H P Trias Lan E Problem The file you attempted to upload was opened E Solution Close the file to be uploaded and then retry the upload E Problem Uploading has aborted E Solution Confirm the communications environment settings and communications log then retry the upload It is also necessary to check the communi
78. nterface communication Connect the BHT connector interface port to the host computer RS 232C interface by using a connector interface cable as shown below Host Computer BHT 4 Connector interface cable aa E irori E rit Y For ActiveSync operating procedures on the BHT refer to Chapter 2 Section 2 5 4 2 5 ActiveSync Serial 126 Chapter 3 Communications Operations of BHT 202B CE 202B W CE Setting up a partnership Upon completion of connection between the host Bet Lo Porirership computer and BHT the host computer displays the ee a screen shown at left Beak reii mal Bos nnd mai a a Hrer ac maki pada a ajani On this screen set up a partnership between the host Ti computer and BHT Cede nnter m hal m ee ea bee Er Bema l Lee ido eRe EE Click the Yes radio button and then click Next psa rent Been rhe y Type an arbitrary BHT name in the Device name box EEN FB and click Next Sines ELIS SS Se aH eo bearer TE To synchronize files select the Files check box and then Makay priser anon Lagi irin Eg iwn al hran ma r a reu iamm l click Next Pe PPTPP ds ee ee h heri pee Tp g tar mme a ee m m eee ea Tea Mad haliei 0 Ere Tham gt gr ere Cie Fina ira sleni Te Cis irean heb fC racket ar MEF wth lads Daa by aR re a TAI Aes a a det ard ae Ton hed i ini alate nc menl ih p aos ee w j 127 fen Compete Wi
79. of the BHT so the displayed level also may vary Software keyboard display hide Shows whether the software keyboard is displayed or hidden Tapping this icon toggles the software keyboard on and off A Displays when the software keyboard is displayed Displays when the software keyboard is hidden 20 Chapter 2 Getting Started the BHT and System Menu Synchronization state Provided on the BHT 202BW CE Displays the open state of the wireless device and the radio field intensity T Displays when the wireless device is open T Ti 7 Shows the radio field intensity with the number of bars Tl TIP The radio field intensity icons M T and Til indicate that the radio link is established but do not assure you that there will be few communications errors Wireless Zero Configuration Provided on the BHT 202BW CE pr Indicates that the Wireless Zero Configuration WZC radio is connected to a wireless network Lag Indicates that the Wireless Zero Configuration WZC radio is not connected to a wireless network Keypad shift state Displays when the keypad is shifted ActiveSync Displays when the BHT is linked with the PC via the IrDA USB or etc interface using Microsoft ActiveSync Alphabet input state Displays when the alphabet input function is activated Pressing the SF ALP ALP key switches between the numeric entry and alphabet entry modes activated Pressing any numeric key displays the alphabet lette
80. of the keys may be set by user programs Shown below is a set of sample functions 30 key pad i g Nan SN Power key B g e Turns the BHT on or off Trigger switch M3 key Trigger switch M4 key C Clear SF Shift ALP Alphabet key Used in combination with numerical keys for special input procedures Holding down this key for 1 5 seconds or more switches between the numeric entry and alphabet entry modes BS Backspace key Moves back one character Pressing this key with the SF key held down in BhtShell returns to the previous screen Magic keys M1 to M5 These keys may be used as an SF key ENT key CTRL key ALT key TAB key CLEAR key backlight function on off key laser lighting key or trigger switch depending upon definition in System Menu or in user programs Although M3 to M5 are set as trigger switches by default user defined virtual key codes can be assigned to them Numerical keys ENT Enter key Used for data input Finalizes the inputted data or operations and starts the corresponding processing Provided on the Grip style BHT 18 Chapter 2 Getting Started the BHT and System Menu 26 key pad 7 Fa i k F Dani w Power key i ro fay oo 1 Turns the BHT on or off if i4 Trigger switch Trigger switch M4 key M3 key Magic keys M1 to M5 These keys may be used as an SF key ENT key CTRL key ALT key TAB key CLEAR key backlight functio
81. on Opens the Beeper Vibration menu 3 Control Panel Opens the Control Panel window 4 File System Opens the File System menu 5 Power Management Opens the Power Management menu 6 Key Opens the Key menu 7 Status Display Opens the Status Display menu 8 Radio Frequency Opens the NIC Control menu On the System Properties Menu double tap the Barcode and the Barcode property appears INVERT Activates or deactivates the black and white inverted label reading function DECODE LEVEL Sets the decode level MARKER Sets the marker ON OFF mode ITF Sets the default minimum number of digits to be read for ITF STF Sets the default minimum number of digits to be read for STF CODABAR Sets the default minimum number of digits to be read for CODABAR Black and white inverted label reading function INVERT This function makes it possible to read white bars on a black background Activating this function might increase the frequency of bar code reading errors Usually this function should be set to OFF 74 Chapter 2 Getting Started the BHT and System Menu DECODE LEVEL You may set the decode level Decreasing the level value increases the bar code reading efficiency but the BHT might misread low quality bar codes split or stained To the contrary increasing the level value decreases the bar code reading efficiency but it will diminish the possibility of misreading The setting range of the leve
82. on sheet NOTE Do not set the DIP switch to any configurations other than one of the five shown above When removing the protection sheet take care not to let any foreign material get into the CU 139 5 4 2 Interface Cable Connection 1 Unplug the AC adapter of the CU 200 from the wall socket 2 Make sure that the host PC is turned off 3 CU 201 Connect the RS 232C interface cable to the interface port of the CU 201 CU 221 Connect the USB interface cable to the interface port of the CU 221 _ Interface cable CU 201 RS 232C CU 221 USB 4 Connect the other end of the RS 232C USB interface cable to the corresponding port of the host PC TIP The CU 221 can be connected via a USB hub to the host PC 140 Chapter 5 Handling the CU 200 Option 5 4 3 Interfacing with the Host PC This section describes how to start communication with the host PC from System Menu The same may apply when you use a user program 1 Turn the host PC on to run Windows 2 CU 201 Plug the AC adapter into a wall socket CU 221 Plug the AC adapter into a wall socket if necessary 3 Make sure that the BHT is turned off and then place it on the CU 200 For CU 201 and CU 221 4 On the host PC initiate a communications program that can use Ymodem 5 Turn the BHT on and run System Menu Select 2 Communication and 1 Ymodem to start SerialTransfer Regarding the interface port Select the IrDA COM4
83. operty appears With this menu you can perform the following transactions m Initializing the memory excluding the Registry m Initializing the memory including the Registry m Initializing the FLASH folder m Running Scandisk through the FLASH folder start P la The table below shows which memory area will be initialized by the initialization transactions listed above Initializing the memory Hat pitt Initializing the Excluding the Including the FLASH folder Registry Registry Data stored in the FLASH folder Not initialized Not initialized Initialized Data stored in other folders Initialized Initialized Not initialized Registry Not initialized Initialized Not initialized Note that the backup of the Registry will be erased To back up the Registry again follow the procedure given in Section 2 3 4 2 Backing up the Registry 17 E Initializing the memory excluding the Registry You can initialize the memory excluding the Registry and files stored in the FLASH folder Initializing procedure 1 Tap the Initialize tab and select the RAM radio button 2 Tap the Initialize button 3 To initialize the memory tap the Yes button to return to the previous menu tap the No button After the BHT displays the screen shown at left for a few seconds it will automatically reboot 78 Chapter 2 Getting Started the BHT and System Menu E Initializing the memory including the Registry You can initial
84. or Never fire e Never put the BHT in places where there are excessively high temperatures such as inside closed up automobiles or in places exposed to direct sunlight Doing so could affect the housing or parts resulting in a fire e Avoid using the BHT in extremely humid or dusty areas or where there are drastic temperature changes S Moisture or dust will get into the BHT resulting in malfunction fire or electrical shock e In environments where static electricity can build into significant charges e g if you wipe off the plastic plate with a dry cloth do not operate the BHT Doing so will result in malfunction or machine failure e Tap the LCD only with the stylus that comes with the BHT Using the tip of a pen or any pointed object will result in a damaged or broken LCD vii N CAUTION Handling the CU e Never disassemble or modify the CU doing so could result in an accident such as fire or NY malfunction e Never put the CU in places where there are excessively high temperatures such as inside closed up automobiles or in places exposed to direct sunlight Doing so could affect the housing or parts resulting in a fire e Avoid using the CU in extremely humid or dusty areas or where there are drastic temperature changes Moisture or dust will get into the CU resulting in malfunction fire or electrical shock e Never cover or wrap up the CU or AC adapter in a cloth or blanket Doing so
85. or include remote control units for television sets and the like Host computer For a host computer having no IrDA interface port use the optical communication unit CU 200 option connected to the host via an RS 232C interface cable Put the BHT on the CU 200 as shown below Grip style BHT E Using USB interface Using a USB interface cable the USB interface ports of the BHT and a host computer can be connected allowing data to be transferred to the host computer Host computer USB interface cable E Using connector interface Using a connector interface cable the RS 232C interface of a host computer and the connector interface port of the BHT can be connected allowing data to be transferred to the host computer Host computer BHT p Connector interface cable EEN a j ot Urn 2 IPT I Chapter 2 Getting Started the BHT and System Menu This chapter summarizes the BHT system configuration and describes the operation including preparation and System Menu which is required for the efficient use of application programs 2 1 BHiIsSystem Contiguration sacn aia ei Gleaner a A ae 12 2 2 Components sit cca seeinAgid athena Wieden aedalini bight Abbess i an ened 16 2 2 1 Name sand FUnCtOnsss ccic scccesvesarevvacsessedvsrsicyaesdeacanseesscvasensveca stvestedsveensacatenesssbushisa Eana AEEA Taaa iR annaas 16 2 2 2 Status Indicators On the ECD rrue suat a E A Aar A aE Na Anaras 20 2 29 Notestor U
86. ove the battery cartridge until the backup operation is completed and the message disappears Now saving Registry Do not remove the battery E Restoring the Registry If the Registry is lost the OS automatically restores it If the OS fails to restore it since the Registry has not been backed up the following error message appears To make the Registry revert to the default initialize the memory including the Registry Refer to Section 2 5 4 3 4 File System Initializing the memory including the Registry 31 2 3 5 Warm and Cold Booting E Warm booting the BHT In any of the following cases warm boot the BHT The BHT makes no response to entry from the touch screen or keys The programs in the BHT malfunction due to any problems Warm booting the BHT will not erase data stored in the RAM but it will erase data being edited and not be saved Warm booting procedure When the BHT power is on press the reset button with the stylus Stylus Reset button 32 Chapter 2 Getting Started the BHT and System Menu E Cold booting the BHT If a problem persists even after warm booting the BHT cold boot the BHT Cold booting the BHT will erase all data stored in the RAM It is recommended that important data be saved into the FLASH folder or uploaded to the host computer Cold booting procedure Turn the BHT off While holding down the reset button with the stylus press the p
87. ower key and then release them Press the power key again and the BHT cold boots E Contents of the memory after warm cold booting the BHT After warm booting After cold booting Data in the FLASH folder Retained Retained Data in other folders Retained Erased Contents of the Registry Retained Erased Data being edited Erased Erased Ifthe Registry has been backed up the backup will apply For the backup procedure refer to Section 2 3 4 2 Backing up the Registry E Application program to run automatically at warm cold boot If any execution program file XXXXXX exe is stored in the FLASH StartUp folder warm or cold booting the BHT automatically runs that program file 33 2 4 Replacement of the Backup Battery If the following warning message appears on the LCD you need to replace the backup battery refer to Section 2 4 1 If you remove the backup battery the contents of the memory may no longer be backed up so that the data stored in the BHT may be lost It is recommended that important data be saved into the FLASH folder or uploaded to the host computer This warning message appears each time the backup battery is fully discharged after 200 times of full discharges Even if this warning message appears you can continue operation by tapping the OK button in the top right corner of the message window Each time the backup battery is fully discharged the internal discharge counter automatically
88. p battery cover 38 Chapter 2 Getting Started the BHT and System Menu 12 Set the clear insulation sheet back into place while threading the battery pull strap through the cutout in the sheet Clear insulation sheet 13 Set the inside cover so that its lock and pawl become fitted between the printed circuit boards r Lock T Pawl Fa Inside cover 39 14 Push the battery cartridge into the BHT The end of the battery pull strap should come out from the left edge of the battery cartridge X Battery cartridge Battery pull strap 15 Set the battery cartridge cover back into place and return the right and left release buttons to the original position Release button Battery cartridge cover Battery pull strap 40 Chapter 2 Getting Started the BHT and System Menu 2 4 2 Resetting the Discharge Counter If you replace the backup battery reset the internal discharge counter in the BhtShell System Properties Menu For detailed operation refer to Section 2 5 4 3 System Properties Menu m Backup Battery Discharge Counter 41 2 5 Operating in System Menu 2 5 1 Desktop Upon completion of setting up 2 described in Section 2 3 2 the desktop appears on the touch screen as shown below Double tapping icons on the desktop runs the corresponding programs E My Device On the desktop double tap My Device The screen shown at left appears With this program you can browse
89. r assigned to that key in this ALP The ALP window appears only on the 26 key pad type when the alphabet input function is window Desktop displa Tapping this icon when an application program is running switches the screen to the desktop display Tapping it again returns to the application execution screen Standby state zz Appears when the CPU comes to be on standby This icon does not appear by default To display it you need to change the setting in System Menu or in user programs For the setting procedure in System Menu refer to Section 2 5 4 3 7 Status Display For that in user programs refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual Caps Lock state Appears when the Caps Lock switch is pressed on the software keyboard 21 2 2 3 Notes for Using the BHT E Windows desktop on the LCD The Windows desktop shown in this manual may be a little different from that in the actual screens on the LCD Windows desktop sample This task tray also may be a little different from that in the actual screen E No refreshing of the LCD screen when on standby To minimize the power consumption the BHT automatically switches to the standby mode after it has not been operated for the specified period In the standby mode the LCD is not refreshed so that icons on the task bar and task tray may not be displayed or refreshed or that the calendar clock may not show the correc
90. re as well as damage to the CU Never use the CU on the line voltage other than the specified level Doing so could cause the CU to break or burn Use the dedicated AC adapter only Failure to do so could result in fire If the power cord of the AC adapter is damaged e g exposed or broken lead wires stop using it and contact your nearest dealer Failure to do so could result in a fire or electrical shock vi N CAUTION Handling the battery cartridge e Never charge a wet or damp rechargeable battery cartridge S Doing so could cause the batteries to break generate heat rupture or burn Handling the BHT e If smoke abnormal odors or noises come from the BHT immediately turn off the power pull out the battery cartridge and contact your nearest dealer Failure to do so could cause smoke or fire e f foreign material or water gets into the BHT immediately turn off the power pull out the battery cartridge and contact your nearest dealer A Failure to do so could cause smoke or fire e If you drop the BHT so as to damage its housing immediately turn off the power pull out the battery cartridge and contact your nearest dealer Failure to do so could cause smoke or fire e Do not use batteries or power sources other than the specified ones doing so could generate heat or cause malfunction S e Never disassemble or modify the BHT doing so could result in an accident such as break
91. rface cable E CU 221 and USB Interface Cable option The CU 221 is an IrDA compliant communications unit and is required when the host computer is not equipped with an IrDA interface port The CU 200 exchanges data and programs with the BHT optically and with the host computer via the USB interface cable 13 BHT Operating System OS Microsoft Windows CE NET 5 0 Application Program Development Environment E PC for application development Item Description OS Microsoft Windows 2000 Professional Service Pack 2 or later Microsoft Windows 2000 Server Service Pack 2 or later or Microsoft Windows XP Professional CPU Pentium ll class processor 450 MHz or faster RAM For Microsoft Windows 2000 Professional Service Pack 2 or Microsoft Windows XP Professional 96 MB or more 128 MB or more recommended For Microsoft Windows 2000 Server Service Pack2 192 MB or more 256 MB or more recommended HDD 200 MB or more hard disk space Display Monitor with 800 x 600 resolution or larger Chapter 2 Getting Started the BHT and System Menu E Application Development Tool Microsoft eMbedded Visual C 4 0 Service Pack 4 or later Microsoft Visual Studio NET or Microsoft Visual Studio NET 2003 You can download Microsoft eMbedded Visual Tools 4 0 and Service Pack 4 from the Microsoft Web site at Microsoft eMbedded Visual C 4 0 http www microsoft com downloads
92. rograms Refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual 122 Chapter 3 Communications Operations of BHT 202B CE 202B W CE 3 5 ActiveSync With Microsoft ActiveSync the BHT can exchange data with the host computer connected by IrDA USB connector interface or spread spectrum communication BHT 202BW CE TIP ActiveSync enables the following Synchronized data transmission Backing up data Copying or transferring data Debugging user programs 3 5 1 Configuring the Host Computer You need a PC equipped with an IrDA interface port NOTE When the BHT is connected with the host via the CU 201 RS 232C interface no ActiveSync can be used The BHT and host computer should be arranged with their IrDA ports facing directly each other Installing ActiveSync 3 7 To use ActiveSync for communication between the BHT and host computer you need to install ActiveSync 3 7 to the host computer Download ActiveSync 3 7 from the Microsoft Web site at http www microsoft com downloads details aspx FamilyID 67e9e87c ca96 48b4 b5d4 f3e047ca510 8 amp displaylang en 123 Setting up ActiveSync 3 7 Make ActiveSync connection settings according to the procedure below S Meresut antet lo Start the installed ActiveSync 3 7 and the screen shown Di fee Tee fino Acne at left appears eojps 5 Wine imne Sbn U eeen bare Sc Liga Choose File Connection Se
93. ry cartridge cover back into place and return the right and left release buttons to the original position Release button L Battery cartridge cover Battery pull strap 156 Appendices Appendix C Quality Assurance Standards C 1 Interface Cables With the interface cables described in this section DENSO WAVE has run the quality assurance test conforming to the EMC Directive for the BHT 202B CE 202BW CE and CU 200 Any connectors other than those specified here are not acceptable They may cause the BHT or CU to fail to work according to the specifications Cable im Dsub connector Dsub 9S Shielded cable 157 BHT 202B CE 202BW CE User s Manual First Edition June 2006 DENSO WAVE INCORPORATED The purpose of this manual is to provide accurate information in the handling and operating of the BHT 202B CE 202BW CE Please feel free to send your comments regarding any errors or omissions you may have found or any suggestions you may have for generally improving the manual In no event will DENSO WAVE be liable for any direct or indirect damages resulting from the application of the information in this manual
94. ry screen Numerical keys Pressing a numerical key corresponding with a desired menu number starts the desired item displayed on the screen ENT key Pressing this key executes the focused item Tab key assigned to the Pressing this key moves the focus M1 key by default SF C BS C keys Pressing this combination returns to the immediately preceding screen Currently active item On the screen above the 1 Execute Program is focused The combination of the SF and C BS C keys is disabled on the following menus in Section 2 5 4 Detailed Description of the Functions in System Menu 2 1 Ymodem Menu 2 2 ActiveSync Infrared 2 3 ActiveSync Serial 2 4 ActiveSync USB 2 5 ActiveSync RF 3 3 Control Panel 3 8 Radio Frequency 5 Explorer 57 E Structure of System Menu System Menu Double tapping the BhtShell shortcut icon on the desktop starts up System Menu Execute Program Executes a user program you select Refer to Section 2 5 4 1 Communication SF C BS C keys Communicates with the host computer Refer to Section 2 5 4 2 System Properties Sets a variety of environmental conditions Refer to Section 2 5 4 3 58 Chapter 2 Getting Started the BHT and System Menu Hardware Test Tests a variety of hardware operations Refer to Section 2 5 4 4 SF C BS C keys Pe Explorer Run
95. s Explorer Refer to Section 2 5 4 5 E upore F U System Information Shows the system program version and memory size Refer to Section 2 5 4 6 59 2 5 4 Detailed Description of the Functions in System Menu 1 Execute Program Choosing 1 Execute Program in System Menu calls up the screen shown at left With this menu you can start an application you want Tap the Browse button The screen shown at left appears Select a file you want to run check that the file name is displayed in the Name box and then tap the OK button Check that the name of the file to be run is displayed in the Open box and tap the OK button 60 Chapter 2 Getting Started the BHT and System Menu 2 Communication Menu Choosing 2 Communication in System Menu calls up the screen shown at left 1 Ymodem Switches to the Ymodem menu where you can set the Ymodem communications parameters and download upload files 2 ActiveSync Infrared Connects to the host computer via IrDA using ActiveSync 3 ActiveSync Serial Connects to the host computer via a connector interface using ActiveSync 4 ActiveSync USB Connects to the host computer via USB using ActiveSync 5 ActiveSync RF Connects to the host computer via RF using ActiveSync 2 1 Ymodem Menu With this menu you can set the communications parameters and download or upload files from to the host computer 7 Choosing 1
96. s of the items above except the CPU STANDBY are Display For details refer to Section 2 2 2 Status Indicators on the LCD Double tap the Radio Frequency and the NIC Control property appears The NIC Control property has the following tabs m Info tab Displaying the wireless module version and opening closing the RF device Network tab Displaying the IP address and MAC address m D tab Setting the ESSID m Option tab Setting the RF options m WEP tab Setting the WEP keys m Link tab Displaying the current communications link status m Ping tab Testing with Ping 86 Chapter 2 Getting Started the BHT and System Menu E Displaying the wireless module version and opening closing the RF device ol Tapping the Info tab on the NIC Control menu displays the screen shown at left This menu displays the following Driver Version Version of the RF driver Firmware Version Firmware version of the wireless module Hardware Version Hardware version of the wireless module You can also open or close the wireless module by tapping the RF Open RF Close or RF Open Continuously button respectively WE If the wireless module is opened by pressing RF Open Closing the NIC Control property automatically closes the RF device even if being opened If you need to display any other window while keeping the RF device open tap the button on the taskbar to minimize the NIC Control property window If the wireless module
97. s the communications operations of the BHT 202B CE 202BW CE the spread spectrum communication BHT 202BW CE only infrared communication USB interface specifications connector interface specifications BHT 202BW CE basic communications specifications communication using Ymodem and ActiveSync for data transfer with the host computer or other devices Chapter 4 Error Messages Lists the error messages which will appear on the LCD if some error occurs in the BHT Chapter 5 Handling the CU 200 Option Describes the handling procedure of the communication unit CU 200 the interfacing with the host computer and the charging of the rechargeable battery cartridge Appendix A Specifications Appendix B Loading an Optional Compact Flash Card Appendix C Quality Assurance Standards E Related Publications BHT 200 CE API Reference Manual BHT 200 CE Class Library Reference Manual 2D Code Scanner Barcode Scanner Keyboard Interface with BHT CE kbifCE User s Guide E Screen Indication The lettering in the screens in this manual is a little different from that in the actual screens File names used are only for description purpose so they will not appear if you have not set files having those names SAFETY PRECAUTIONS Be sure to observe all these safety precautions E Please READ through this manual carefully It will enable you to use the BHT and CU correctly E Always keep this manual nearby for speedy reference Strict obs
98. screen shown at left On She Sater oF thee barge Follow the on screen instructions Refer to Section 2 3 2 Setting up 2 Calibrating the touch screen 50 Chapter 2 Getting Started the BHT and System Menu Dialing Properties Disina Pranerties HOG On the Control Panel window double tap Dialing and the Dialing Properties window appears You can set up the telephone line Owner Properties On the Control Panel window double tap Owner and the Owner Properties window appears Tap the Network ID tab to display the window shown at left You can specify a user name password and domain required to access the network resource 51 Volume amp Sounds Properties On the Control Panel window double tap Volume amp Sounds and the Volume amp Sounds properties window appears volana amp Sound Pro id Ed Tap the Volume tab to display the screen shown at left You can make the following settings Adjust the beeper volume except volumes for key entry and screen taps Enable disable the beeper for events Enable disable the beeper driven by programs Enable disable the beeper for notification NOTE You may adjust the beeper volume to six levels 0 to 5 on this screen however four levels are available in practice since levels Pon ec Pew low E 1 and 2 and levels 3 and 4 produce the same volume volume amp Sound Oro i El Tap the Sounds tab to display the screen shown at left
99. sing the BHT cinnnamnnona nal a ai eee ee 22 2 3 Preparations isdedi joie ened iach Menta and bist abate Neda E das a Ea nes 23 2 3 1 Setting up 1 Loading the battery Cartridge cccccccecceeeeeeeeeeneeeeeeeeeeeeeeeeeeaeeseeeeeeseaeeeseeeeeseeeeseeeeseaes 23 2 3 2 Setting up 2 Calibrating the touch SCrE N cceccceeeeeeeeeeeeeeeeeeeeeeeaeeeseeaeeeseaeeesecaeeeseeeeeeseneeeesiaeeesnnees 28 2 3 3 Battery Replacement Notes cccecscccseeceeeeeeeeeeesaeeceeaeeeesneeeesaneeeeeaeeeseaeeseeaeeeeeeaeeseeaeesseeeseeaeeeeeeeees 29 2 3 4 BHT Turning off Notes ictuecesecii atda a aa ach chen Abad ned 30 1 shutdown in progress message iinei reia variations Gdns A ENEE EE Ear ESENE 30 2 Backing p the Registry teso a e a ele ea apa Aaa a Aea Vana ante 31 29 9 Warmand Cold Booting ainean nahin Genel ei ot A ae ae A AAE 32 2 4 Replacement of the Backup Battery cccccccecseseeeeeneeeeeeeeeeeeeaeeeteaeeeeseaeeeeeeaeeseeaaeeeseaaeeeeaeeseeaeeeseaeeeseaeeeeees 34 2 4 1 Replacing the Backuip Battery iiiccsc seccesestec dis deveiycdeeweiaeeas eee vied aaa aada ari ANAS AA EREDE Chea dees NENIES EN 35 2 4 2 Resetting the Discharge Counter cccccccecsceeeeeeeeeeeneeeeeeneeeeaeeeeeeaeeeseaaeeeeeaeeeeeaeeesseaeeeseeeessaeeeeenneess 41 2 5 O perating in System MenU iea aa aeia aaa Aaaa ranted ale esl ee 42 2 5 1 D sktopria nirien pii d da a hike Abe a a A ia 42 PATA Starts MOMU EEEE EE L E AE N IEE EE
100. so could result in a fire or electrical shock SOOM 137 AN CAUTION If you are not using the CU for a long time be sure to unplug the AC adapter from the wall socket for safety Failure to do so could result in a fire When caring for the CU unplug the AC adapter from the wall socket for safety Failure to do so could result in an electrical shock Never cover or wrap up the CU or AC adapter in a cloth or blanket Doing so could cause the unit to heat up inside deforming its housing resulting in a fire Always use the CU and AC adapter in a well ventilated area Keep the power cord away from any heating equipment Failure to do so could melt the sheathing resulting in a fire or electrical shock 138 Chapter 5 Handling the CU 200 Option 5 4 Communicating with the Host PC 5 4 1 Setting the Transmission Speed of the CU 200 CU 201 Set the transmission speed to the same value as that of the BHT and host PC by using the DIP switch CU 221 The transmission speed is automatically determined by the host PC The DIP switch is located next to the power inlet connector on the side of the CU 201 1 Remove the protection sheet of the DIP switch from the CU 201 2 Set the selectors of the DIP switch as shown below Protection sheet 175 200 bps SF O bpa w ED oe Wod 129 125 JHI Dhi 36 400 bps 19 200 bps on OWE Gx BHn 123 u2a DEH aa 9 600 bps GIP switch 3 Reinstall the protecti
101. st It is recommended that important data be saved into the FLASH folder or uploaded to the host computer The battery cartridge will gradually deteriorate during the repeated cycles of charging and discharging due to its properties When the battery operation period becomes shortened due to its deterioration even if it has been charged for the specified hours replace the battery cartridge with a new one Use only DENSO WAVE authorized battery cartridges and chargers e Never dispose of battery cartridges into a fire They should be recycled properly Do not throw them in a trash e When disposing of the battery cartridge cover the terminal pins with vinyl tape to prevent short circuit 29 2 3 4 BHT Turning off Notes 1 Shutdown in progress message If you press the power key to turn off the BHT the BHT displays the following message and starts preparation for shutdown Shutdown in progress Do not remove the battery When the above message is displayed do not remove the battery cartridge If you do so the data stored in the BHT may be lost 30 Chapter 2 Getting Started the BHT and System Menu 2 Backing up the Registry The Registry is the part of Windows CE that stores setup information required for operating the BHT E Backing up the Registry When the BHT is on pressing the power key with the SF ALP SF key held down displays the screen shown at right and starts backing up the Registry Do not rem
102. t date or time The default is one second The period can be changed in user programs For details refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual E Opening the wireless communications device To minimize the power consumption the wireless communications device in the BHT is not working in regular operation To make the BHT ready for wireless communication you need to open the wireless communications device with the RF Open Close switches in System Menu or by coding in user programs For the opening closing procedure with the RF Open Close switches in System Menu refer to Section 2 5 4 3 8 Radio Frequency Displaying the wireless module version and opening closing the RF device For coding in user programs refer to the BHT 200 CE API Reference Manual or BHT 200 CE Class Library Reference Manual 22 Chapter 2 Getting Started the BHT and System Menu 2 3 Preparation 2 3 1 Setting up 1 Loading the battery cartridge Before the first use of the BHT be sure to load the battery cartridge as shown below The battery cartridge is not loaded in the BHT when shipped from the factory E Into the BHT body 1 Turn the BHT upside down 2 Slide the release buttons in the direction shown below and remove the battery cartridge cover 3 Push the battery cartridge into the BHT To remove it first make sure that the BHT is turned off Slide the release buttons remove the ba
103. t to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense NOTE This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CAUTION Radio Frequency Radiation Exposure This device is approved for hand held use only and to comply with applicable FCC radio frequency exposure regulations must be used with a distance of at least 20 cm 7 9 inches between the antenna and the body of any person at all times d
104. the USB host PC or USB hub via the USB interface Connecting the AC adapter supplies power to the CU 221 If no AC adapter is connected turning on the USB host PC and USB hub supplies power to the CU 221 NOTE To charge the battery cartridge use the AC adapter except when the CU 221 is connected to a self powered hub capable of supplying power 5V 500 mA via the USB line NOTE To charge the battery cartridge even when the USB host PC is in suspend mode use the AC adapter Power inlet connector a A WARNING If smoke abnormal odors or noises come from the CU immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock If foreign material or water gets into the CU immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock a gt al If you drop the CU so as to damage its housing immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock Use the dedicated AC adapter only Failure to do so could result in a fire Never use the CU on the line voltage other than the specified level Doing so could cause the CU to break or burn If the power cord of the AC adapter is damaged e g exposed or broken lead wires stop using it and contact your nearest dealer Failure to do
105. tion 3 1 2 RF Related Parameters 88 E Setting the WEP keys Mii Het Ea ae rset lel Authe ntication Open Wer hankita were iera a a mt Tipar ie a Wor Hian Ket iera ia rar E gf io Chapter 2 Getting Started the BHT and System Menu Tapping the WEP tab on the NIC Control menu displays any of the following three types of screens according to the authentication type At left Open Below at left Shared key 40 bit WEP On the next page Shared key 128 bit WEP You can set the following WEP Set the authentication system when the WEP is enabled Open Disable the encryption Shared 40 bit Use a 40 bit WEP key Shared 128 bit Use a 128 bit WEP key Key 1 through 4 Define four types of encryption keys WEP keys 1 to 4 available only when the Shared 40 bit or Shared 128 bit is selected Transmit Key Activate any one of the WEP keys 1 through 4 already defined available only when the Shared 40 bit or Shared 128 bit is selected WE To enable the encryption with an WEP key choose Shared in the WEP box For Transmit Key select an WEP key already defined For details about each parameter refer to Chapter 3 Section 3 1 2 RF Related Parameters 89 E Displaying the current communications link status MIC Contrel owl Tapping the Link tab on the NIC Control menu displays the screen D Joeman ver Unk Jeng Led shown at le
106. ttery cartridge cover and pull up the battery pull strap Release button 5 Battery cartridge cover Release button Battery pull strap 4 Set the battery cartridge cover back into place and slide the release buttons to the original position 5 Place the BHT on the CU 200 to charge the rechargeable battery cartridge Refer to Section 5 5 Battery cartridge Battery pull strap 23 E Into the grip 1 Take the bottom cover off the grip by removing the screw Bottom cover 2 Pull the lock in the direction of the arrow and insert the battery cartridge into the grip with the boss facing as shown below Battery cartridge A i Bottom cover Screw 24 Chapter 2 Getting Started the BHT and System Menu AA WARNING e Never disassemble or heat the battery cartridge nor put it into fire or water doing so could cause battery rupture or leakage of battery fluid resulting in a fire or bodily injury Do not carry or store the battery cartridge together with metallic ball point pens necklaces coins hairpins etc Doing so could short circuit the terminal pins causing the batteries to rupture or the N battery fluid to leak resulting in a fire or bodily injury e Avoid dropping the battery cartridge or letting it undergo any shock or impact Doing so could cause the batteries to break generate heat rupture or burn e Never charge the rechargeable battery cartridge where any inflam
107. ttings The screen shown Eick hed Cearrmectec tos conraci eas mai la raca ta Har at left appears ta om Click the check box Allow serial cable or infrared Sur Wiating in dence ia paac Gsi Connecedd connection to this COM port and select Infrared Port Cpa nd A oR lt a Click the check box Allow network Ethernet and Gii COM pret ia armias Remote Access Service RAS server connection with T disa J30 renacer ath tha dk iop compia this desktop computer Sisu UDN n maah Tap OK Eir posed Phera and ewes Acces Ban Bidu Hik on ridb Biga ieee w Ihen tin eon in T sik OF j Cmi we Setting up ActiveSync 3 7 has been completed 124 Chapter 3 Communications Operations of BHT 202B CE 202BW CE 3 5 2 Connection Using ActiveSync When connected by IrDA USB or connector interface E IrDA communication Arrange the BHT and host computer with their IrDA ports facing directly each other as shown below No ActiveSync can be used for connection via the CU 201 RS 232C interface Host Computer IrDA communication For the operating procedure of ActiveSync on the BHT refer to Chapter 2 Section 2 5 4 2 2 ActiveSync IrDA m USB communication Connect the BHT to the host computer by using a USB interface cable as shown below Host Computer USB interface cable For the operating procedure of ActiveSync on the BHT refer to Chapter 2 Section 2 5 4 2 4 ActiveSync USB 125 E Connector i
108. ume for the following operations Beeper From the six levels 0 low to 5 high Default 5 Key clicks Beeper volume to be applied when any key is pressed Default Loud Half press key clicks Beeper volume to be applied when any key is halfway pressed Default OFF Screen taps Beeper volume to be applied when the screen is tapped Default Loud Trigger key clicks Beeper volume to be applied when the trigger switch is pressed Default OFF Laser lighting key clicks Beeper volume to be applied when the laser lighting key is pressed Default OFF The trigger switch or laser lighting key can be assigned to magic keys Switching the beeper and vibrator Fh tate acy Choose the Rumble Device tab to display the screen shown at left You may select any of three ways beeping only vibrating only and beeping and vibrating as a confirmation of completion of bar code reading Beeper Beeping only default Vibration Vibrating only Beeper Vibration Beeping and vibrating 76 3 3 Control Panel Bates BHT o o hanoh Certificates Cene gt D Dri Tira ii Miia Tiig Trgi 3 4 File System Chapter 2 Getting Started the BHT and System Menu Double tap the Control Panel and the Control Panel window appears With this menu you can set up the basic Windows operating environment For details refer to Section 2 5 2 m Control Panel Double tap the File System and the File System pr
109. uring use This transmitter and its antenna should not be placed next to other antennas or similar radiating structures LABELING For USA and Canada OMPLIES WITH 21 CFR 1040 10 AND 1040 11 INT TO LASER NOTICE No 50 DATED JULY 26 2001 For USA and Canada CONTAINS FCC ID H9PLA4137 CANADA 1549104431A THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION I SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE HAY NOT CAUSE HARNFUL INTERFERENCE AND 2 THIS DEVICE HUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT HAY CAUSE UNDESIRED OPERATION THIS DEVICE COMPLIES WITH RSS 210 THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN TCES 003 CET APPAREIL NUMERTQUE DE LA CLASSE A ESTCONFORME A LA NORME HHB 003 DU CANADA m Grip style BHT For USA and Canada FCC ID H9PLA4137 CONTAINS CANADA 1549104431A THIS DEVICE COMPLIES WITH PART 5 QF TIIE FCC RULES OPERATION 15 SUBJECT TO THE FOLLOWING TWO CONDITIONS 2 THIS DEVICE AY NOT CAUSE HARMFUL INTERFERENCE AND 2 TITS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE TIIAT 4AY CAUSE UNDESIRED OPERATION THIS DEVICE COMPLIES WITII RSS 2 0 THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES D02 CET APPAREIL NUMERIQUE DE LA CLASSE A ESTCONFORME A LA NORME NMB 003 DL CANADA Declaration of Conformity For European Union
110. using ActiveSync refer to Chapter 3 Section 3 5 ActiveSync T The BHT can be setup so that ActiveSync which allows connection with the host computer begins automatically when the USB cable is plugged into the BHT when it is turned on For further details refer to Section 2 5 4 3 System Properties Menu lf ActiveSync connection succeeds pC comer mare atc If ActiveSync connection succeeds the BHT beeps once and displays the ActiveSync icon circled in red at left in the task tray If ActiveSync connection fails If ActiveSync connection fails the BHT beeps once and does not display the ActiveSync icon 71 2 5 ActiveSync RF Choosing 5 ActiveSync RF on the Communication menu connects the BHT to the host computer via the RF interface port NOTE Before proceeding to ActiveSync RF you need to Set up a partnership between the host computer and BHT by running ActiveSync Infrared Make the RF settings according to the procedure given in section 2 5 4 3 8 Radio Frequency If the RF settings are not made correctly ActiveSync RF cannot run When the BHT is opening the RF device and connecting to the network it displays the screen shown at left Connection to the network may take several tens of seconds depending upon the network environment When the DHCP is used for getting an IP address connection to the network will require more time than when the IP address is fixed If co
111. w at left DateTime j Set the date time and time zone Then tap the OK button l3 1G 17 18 HAMS MTG 0 i204 aM iamm Paii Time LE E 7 O Aubor adai chock for 28 Chapter 2 Getting Started the BHT and System Menu 2 3 3 Battery Replacement Notes E When is battery replacement needed If the Charge the battery appears on the LCD replace the battery cartridge with a fully charged one If you leave the BHT without replacing the battery cartridge then the integrated calendar clock or data will no longer be backed up so that the calendar clock may stop or the data may be lost Grip style BHT If Charge the battery appears on the LCD when battery cartridges are loaded in both the BHT body and grip replace both battery cartridges As long as the voltage level of either one of battery cartridges is higher than the specified level this warning message will not appear Always remove both battery cartridges even if you only have one fully charged replacement battery cartridge on hand NOTE e Replace the battery cartridge quickly e Be sure to turn the BHT off before battery replacement e Load a charged battery cartridge within 3 minutes after the removal to avoid data loss e After battery replacement turn the BHT on and check its operation e If you leave the BHT with no battery cartridge loaded for a long time the contents of the memory may no longer be backed up so that the data stored in the BHT may be lo
112. want to store a downloaded file and then a j tap button and the BHT waits for a file to be downloaded Folder where you want to store a downloaded file es BI amp Doumer I en H m piin mgm Fier If you download a file having the same name as one already in the same folder the newly downloaded file replaces the old one Upon completion of downloading the BHT sounds a long beep once and displays the screen shown at left 63 If an error occurs during downloading If some error occurs during downloading the BHT beeps three times and shows one of the following screens eet ae E Problem The memory is insufficient for storing files to be downloaded E Solution Delete unnecessary files in the memory or decrease the size of the file to be downloaded E Problem The path of the file to be downloaded is too long E Solution Change the file name or the folder where you want to store the downloaded file E Problem The file you attempted to download was opened E Solution Close the file to be downloaded and then retry the download 64 Chapter 2 Getting Started the BHT and System Menu E Problem Downloading has failed E Solution Confirm the communications environment settings and then retry the download It is also necessary to check the communications environment setup of the host computer E Problem Downloading has aborted E Solution Confirm the communicatio
113. width Depth of field 0 15mm 5 91 mils 110 to 160mm 4 33 to 6 30 inches 0 19mm 7 48 mils 100 to 205 mm_ 3 94 to 8 07 inches 0 25mm 9 84 mils 75 to 310 mm 2 95 to 12 20 inches 40 to 450 mm 1 57 to 17 72 inches 4 45 to 620 mm 1 77 to 24 41 inches 45 to 700 mm 1 77 to 27 56 inches 70 to 895 mm 2 76 to 35 24 inches 0 33mm_ 12 99 mils 0 50mm_ 19 69 mils 0 635 mm 25 00 mils 1 00 mm_ 39 37 mils 1 Under the following conditions 5 Under the following conditions Ambient illuminance 500 Ix Xenon arc lamp Code 39 14 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max Ambient illuminance 500 Ix Xenon arc lamp Code 39 15 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 8 Under the following conditions Ambient illuminance 500 Ix Xenon arc lamp ITF conforming to the UPC Shipping Container Code Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 0 625 magnification 2 Under the following conditions Ambient illuminance 500 Ix Xenon arc lamp Code 39 5 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max Under the following conditions Ambient illuminance 500 Ix Xenon
114. with the or by hana stylus for data entry Doing so may result in Trigger switch M4 key Press this switch to start bar code reading e Press this halfway to emit a laser light e Press this fully to scan a bar communications failures Interface port USB interface port and connector interface port Trigger switch M3 key Press this switch to start bar code reading e Press this halfway to emit a laser ka light Hand strap Be sure to put your e Press this fully to scan a bar hand through this strap code Reset button to prevent you from IrDA interface port aroppingine BHT Used to exchange data programs with y the host computer via its integrated IR port or via the optical communication unit CU 200 Reading window s i Hand belt Fa Compact Flash card slot Insert an optional Compact Flash F card into this memory extension slot Rechargeable battery cartridge Main power source of the BHT Release button Release button Slide this button to open the battery cartridge cover Battery cartridge cover Remove this cover to replace the battery cartridge 16 Chapter 2 Getting Started the BHT and System Menu E Grip style BHT Trigger switch M5 key Press this switch to start bar code reading e Press this halfway to emit a laser light e Press this fully to scan a bar code 17 The functions

Download Pdf Manuals

Related Search

Related Contents

Samsung GT-C5130 Manuel de l'utilisateur  Spire Cassi 349  COHU, INC. Electronics Division  Télécharger (754 ko)    proyecto. modulo de sistema de información para el control total en  Sharp XV-Z17000 data projector  Samsung HMX-S10BP Užívateľská príručka  

Copyright © All rights reserved. Failed to retrieve file