Dell Laptop D505 User's Manual
Contents
1. NOTICE Before turning on the computer replace all screws and ensure that no stray screws remain inside the computer Failure to do so may result in damage to the computer 2 Turn on the computer NOTE After replacing the system board enter the computer Service Tag into the BIOS of the replacement system board 3 Insert the floppy disk or CD that accompanied the replacement system board into the appropriate drive Follow the instructions that appear on the screen Back to Contents Page Back to Contents Page Flashing the BIOS Dell Latitude D505 Service Manual 1 Ensure that the AC adapter is plugged in and that the main battery is installed properly Ei NOTE If you use a BIOS update program CD to flash the BIOS set up the computer to boot from a CD before inserting the CD 2 Insert the BIOS update program floppy disk or CD and turn on the computer Follow the instructions that appear on the screen The computer continues to boot and updates the new BIOS When the flash update is complete the computer will automatically reboot 3 Press F25 during POST to enter the system setup program 4 Press lt Alt gt and lt F gt to reset the computer defaults 5 Press Esc Suspend select Save changes and reboot and press Enter to save configuration changes 6 Remove the flash BIOS update program floppy disk or CD from the drive and restart the computer Back to Contents Page Back to Contents Page Pi2. Palm Rest Dell Latitude D505 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard NOTICE You must remove the display assembly before you remove the palm rest the display hinges pass through the back of the palm rest 3 Remove the display assembly 4 Remove the three M2 5 x 5 mm screws labeled circle P from the top of the palm rest 5 Remove the M2 5 x 5 mm screw labeled M2 5x5 from the metal shield 1 M2 5 x 5 mm screws labeled circle P 3 2 top of the palm rest 3 M2 5 x 5 mm screw labeled M2 5x5 6 Turn over the computer and remove the 13 M2 5 x 8 mm screws M2 5 x 8 mm screws 13 3R690 7 Disconnect the touch pad connector from the system board system board connector touch pad connector NOTICE Carefully separate the palm rest from the computer base to avoid damage to the palm rest 8 Starting at the back center of the palm rest use your fingers to separate the palm rest from the computer base by gently lifting up the palm rest while pressing down on the back of the computer base Ei NOTE When you rei
3. routing clip NOTICE To avoid damaging the speaker cable when inserting it back into the routing clip slightly bend open the clip with your finger insert the cable and then press the clip closed 6 Disconnect the speaker connector from the system board connector NOTICE Handle the speakers with care to avoid damaging them 7 Remove the M2 5 x 5 mm screw labeled M2 5x5 from the speakers 8 Gently pull out on the front plastic computer base while pulling up the speakers 9 Remove the reserve battery from the speakers TILLDUO reserve battery 3R459 speaker latches N M2 5 x 5 mm screw labeled M2 5x5 63PDH 6 computer base a speaker onnea e speaker cabe routing eip Back to Contents Page Back to Contents Page Base Latch Dell Latitude D505 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the display assembly 4 Remove the palm rest 5 Remove the speakers 6 Press in the release button slightly press together the two securing clips nearest the back of the computer and then pull the base latch
4. DD mounting screws 4 HDD security screws 2 HDD connector D module housing only no HDD Keyboard 1M709 English US international single pointing 63PDH M2 5 x 5 mm screw LCD Display Assembly F1788 XGA panel 14 1 inch D1724 XGA panel 15 inch W3434 SXGA panel 15 inch F1484 display latch X1261 display bezel 14 1 inch H1370 display bezel 15 inch H1375 top cover 14 1 and 15 inch includes latch Y0231 modem daughter card MDC OR160 primary battery 12 6 V 6 cell OM787 D module second battery 12 6 V 6 cell 3R459 reserve battery 5U092 AC power brick only 65 W 9T215 AC adapter PA10 90 W must be used with D Dock and D Port TY295 power cord flat US 1 m 3 ft K2490 power cord for D Docks only US 2 m 6 ft H0286 rubber strap for power cord management Processors Intel Pentium M Intel Pentium M Intel Celeron M a CX Speaker Microprocessor Thermal Cooling Assembly H1309 microprocessor thermal cooling assembly 3X548 TM1400 dual band a b combo card MPCI J4781 Wireless 1450 dual band 802 11a b g WLAN MPCI 2U381 PC Card with Bluetooth wireless technology internal Back to Contents Page
5. Dell Latitude D505 Service Manual Before You Begin Memory Module Mini PCl Card and Devices System Components Reserve Battery Hard Drive PC Card With Bluetooth Wireless Technology Keyboard Modem Microprocessor Thermal Cooling Assembly Microprocessor Module Display Assembly and Display Latch Palm Rest Docking Doors Speakers Base Latch Fan System Board Flashing the BIOS Pin Assignments for I O Connectors Mini Recommended Spares List Notes Notices and Cautions 3 NOTE A NOTE indicates important information that helps you make better use of your computer NOTICE A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A CAUTION A CAUTION indicates a potential for property damage personal injury or death Information in this document is subject to change without notice 2003 2004 Dell Inc All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo and Latitude are trademarks of Dell Inc Intel Pentium and Celeron are registered trademarks of Intel Corporation Microsoft and Windows are registered trademarks of Microsoft Corporation Bluetooth is a trademark owned by Bluetooth SIG Inc and is used by Dell Inc under license Other trademarks and trade names may be used in this document to refer to either the entities clai
6. Display Assembly A NO UJ CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer NOTICE You must remove the display assembly before you remove the palm rest Follow the instructions in Preparing to Work Inside the Computer Remove the keyboard Open the display assembly approximately 180 degrees and support the display assembly so that it does not open past this position Pull up on the pull tab that is attached to the display cable connector to remove the connector from the system board Release the display cable from the three display cable routing clips Release the two antenna cables from the two antenna securing clips Disconnect one antenna cable from the display by holding the two gold antenna connectors and gently pulling them apart Then disconnect the other antenna cable The gold antenna connectors on each cable are keyed to ensure that they are correctly reconnected M2 5 x 5 mm screws 4 63PDH pull tab i display cable connector i system board connector N i display see Mini RSL antenna securing clips 2 4 computer base 8 antenna connectors 4 8 Remove the four M2 5 x 5 mm screws 9 Rotate the display assembly
7. able to the display cable connector and then secure the display cable in its three display cable routing clips Back to Contents Page Back to Contents Page Microprocessor Thermal Cooling Assembly Dell Latitude D505 Service Manual Removing the Microprocessor Thermal Cooling Assembly A O CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer NOTICE Disconnect the computer and any attached devices from electrical outlets and remove any installed batteries Follow the instructions in Preparing to Work Inside the Computer Remove the keyboard Disconnect the display cable from the display cable connector on the system board Release the two antenna cables from the two antenna securing clips Disconnect one antenna cable from the display by holding the two gold antenna connectors and gently pulling them apart Then disconnect the other antenna cable The gold antenna connectors on each cable are keyed to ensure that they are correctly reconnected 1 antenna connectors 4 2 display cable connector 3 display cable connector on system board 4 antenna securing clips 2 5 antenna cables 2 Ei NOTE You can remove the microprocessor th
8. d cables NOTICE To prevent damage to the Mini PCI card connector do not use tools to spread the securing clips that secure the card b Release the Mini PCI card by spreading the securing clips until the card pops up slightly c Lift the Mini PCI card out of its connector 5 Slide the new Mini PCI card firmly into the connector 6 Connect the antenna cables from the Mini PCI card to the antenna connectors on the computer antenna cables 2 antenna connectors on card 2 7 Lower the Mini PCI card toward the inner tabs to approximately a 20 degree angle 8 Continue lowering the Mini PCI card until it snaps into the inner tabs of the connector 9 Replace the cover Devices Your computer ships with an optical drive installed in the module bay However the device security screw is not installed in the optical drive but packaged separately When you install your device in the module bay you can install the device security screw NOTICE Insert devices into the module bay before you dock and turn on the computer NOTE You do not need to install the device security screw unless you want to secure the module inside the computer for security purposes If the Device Security Screw Is Not Installed NOTI CE To prevent damage to devices place them in a safe dry place when they are not installed in the computer Avoid pressing down on them or placing heavy objects on top of them 1 Press the device latch releas
9. e so that the latch release pops out device latch release 2 Pull the device by the latch release to remove the device from the module bay If the Device Security Screw Is Installed 1 If the computer is connected to a docking device docked undock it See the documentation that came with your docking device for instructions NOTI CE To prevent damage to devices place them in a safe dry place when they are not installed in the computer Avoid pressing down on them or placing heavy objects on top of them 2 Close the display and turn the computer over 3 Use a 1 Phillips screwdriver to remove the M2 x 3 mm screw from the bottom of the computer 4 Press the device latch release so that the latch release pops out 5 Pull the device by the latch release to remove the device from the module bay Back to Contents Page Back to Contents Page System Components Dell Latitude D505 Service Manual NOTICE Only a certified service technician should perform repairs on your computer Damage due to servicing that is not authorized by Dell is not covered by your warranty NOTICE Unless otherwise noted each procedure in this document assumes that a part can be replaced by performing the removal procedure in reverse order delay semon semas speakers dS mono o neaawe 7 semmas 3 palm rest with touch pad D1482 10 fan J 1043 5 computer base fst microprocessor thermal c
10. er and screw NOTICE If the memory module cover is difficult to close remove the module and reinstall it Forcing the cover to close may damage your computer 6 Insert the battery into the battery bay or connect the AC adapter to your computer and an electrical outlet 7 Turn on the computer As the computer boots it detects the additional memory and automatically updates the system configuration information Mini PCI Card If you ordered a Mini PCI card at the same time that you ordered your computer Dell has already installed the card for you A CAUTION Before working inside your computer read the safety instructions in your Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface NOTICE Handle components and cards by their edges and avoid touching pins and contacts 1 Follow the instructions in Preparing to Work Inside the Computer 2 Turn the computer over and loosen the captive screw labeled C on the Mini PCI card cover 3 Place your finger under the cover at the indentation lift up the cover and slide the cover open 4 If a Mini PCI card is not already installed go to step 5 If you are replacing a Mini PCI card remove the existing card a Disconnect the Mini PCI card from any attache
11. ermal cooling assembly with the fan attached 6 Loosen in consecutive order the four captive screws labeled 1 through 4 that secure the microprocessor thermal cooling assembly to the system board microprocessor thermal cooling assembly H1309 captive screws 4 NN 7 Lift up the microprocessor thermal cooling assembly and remove it from the system board microprocessor thermal cooling assembly H1309 Installing the Microprocessor Thermal Cooling Assembly 1 Slip the left side of the microprocessor thermal cooling assembly underneath the palm rest and then place the assembly over the microprocessor 2 Tighten the four captive screws labeled 1 through 4 in consecutive order While tightening the screws ensure that the cooler plate is not higher than the captive screw head incorrectly installed heat sink correctly installed heat sink 3 Reconnect the two antenna cables and then secure them into the two antenna securing clips 4 Reconnect the display cable to the display cable connector and then secure the display cable in its three display cable routing clips Back to Contents Page Back to Contents Page Microprocessor Module Dell Latitude D505 Service Manual Removing the Microprocessor Module A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wris
12. hich is also visible on a barcode label on the bottom of the computer The replacement kit for the system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board NOTICE Disconnect the computer and any attached devices from electrical outlets and remove any installed batteries NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the modem 4 Remove the display assembly 5 Remove the palm rest 6 Remove the microprocessor thermal cooling assembly 7 Remove the microprocessor 8 Remove the speakers 9 Remove the two M2 5 x 5 mm screws labeled B 3 TIM aS lg pn kil M2 5 x 5 mm screws labeled B 2 63PDH system board W3344 10 Turn over the computer and remove the four M2 x 4 mm screws labeled B that secure the system board to the computer base ee a a TE i EI 1 i sree tt Mi Ak ae M2 x 4 mm screws labeled B 4 98MKC 11 Gently push down near the middle of the back plastic computer base so that the two system board securing clips clear their slots and then pull out the system board system board securing clips 2 Installing the System Board 1 Follow all of the steps in Removing the System Board in reverse order
13. in the fully open position before seating the microprocessor module Seating the microprocessor module properly in the ZIF socket does not require force NOTICE A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket Align the pin 1 corner of the microprocessor module with the pin 1 corner of the ZIF socket and insert the microprocessor module K NOTE The pin 1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin 1 corner of the ZIF socket NOTICE You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket When the microprocessor module is correctly seated all four corners are aligned at the same height If one or more corners of the module are higher than the others the module is not seated correctly Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board 3 Replace the other computer parts you removed earlier in this procedure Update the BIOS using a flash BIOS update program floppy disk or CD For instructions on how to flash the BIOS see Flashing the BIOS Back to Contents Page Back to Contents Page Display Assembly and Display Latch Dell Latitude D505 Service Manual Display Assembly Display Bezel Display Panel Display Latch
14. ming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Model PP10L April 2004 Rev A01 Back to Contents Page Before You Begin Dell Latitude D505 Service Manual Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer A A A 10 CAUTION Only a certified service technician should perform repairs on your computer Damage due to servicing that is not authorized by Dell is not covered by your warranty Read and follow the safety instructions in the Product Information Guide that came with the computer CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface CAUTION Handle components and cards with care Do not touch the components or contacts on a card Hold a card by its edges or by its metal mounting bracket Hold a component such as a microprocessor by its edges not by its pins NOTI CE To avoid damaging the computer perform the following steps before you begin working inside the computer Ensure that the work surface is flat and clean to prevent scratching the computer cover Save any work in progress and exit all open programs Turn off the computer a
15. n Assignments for I O Connectors Dell Latitude D505 Service Manual USB Connector Video Connector Parallel Connector S Video TV Out Connector Serial Connector EEE 1394 Connector USB Connector Video Connector 54432 1 a ferajo ve 5 GND 13 CRT_HS e ono fas crys sja w Parallel Connector lOOVOOVOODODOLO OOOOOOOOOOO 13 7 PFPFPFPFPFPFP 25 d 14 pin signa en signal 2 fo n feos 2 AFD 3M 6 erpa ERROR e Jro sur e Jro a o S Video TV Out Connector odo 4 DODO 4 Lj Composite Video Pin Signal Pin signar 2 foco fe fosa a ron e fas O o a 5 wo IEEE 1394 Connector 1234 Back to Contents Page Back to Contents Page Mini Recommended Spares List Bottom Base Parts Memory 9 CD 9 Modem DVD Power Source Fan Processors Floppy Drive Speaker Hard Drive and Accessories Microprocessor Thermal Cooling Assembly Keyboard Wireless LCD Display Assembly E4 NOTE The part numbers listed below are subject to change Bottom Base Parts U2983 bottom latch with spring latch release for LCD 7R316 docking doors with spring 24X CD D module CD RW DVD Combo D Module 4X DVD RW R D module J 1043 fan Floppy Drive floppy drive D module Hard Drive and Accessories 1E321 20 G HDD W1081 30 G HDD J1749 40 G HDD 60 G HDD primary HDD carrier with bezel H
16. n Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the display bezel 4 Remove the eight M2 x 5 mm screws from each side of the display panel adapter rails 5 Lift the display panel and rotate the display panel out of the display cover 6 Remove the four M2 x 3 mm screws from each side of the display panel to remove the adapter rails When reinstalling the adapter rails to the replacement display panel orient the rails so that the This side up markings are facing you and then reattach the rails with the four M2 x 3 mm screws The This side down markings on the rails should be visible from the rear side of the display panel reco asptoy pane a adapers I 3 2x 3mm screws 9 a This side up markings 7 Press in both sides of the top flex cable connector and pull the top flex cable connector away from the display connector 8 Use the pull tab to disconnect the bottom flex cable connector from the inverter connector pull tab on bottom flex cable connector top flex cable connector display connector inverter connector 15 Inch Display Panel A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrosta
17. nate mode NOTI CE Hard drives are extremely fragile even a slight bump can damage the drive NOTE Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell Follow the instructions in Preparing to Work Inside the Computer gt KO OO IO Turn the computer over Use a standard 1 Phillips screwdriver to remove the two M2 5 x 5 mm screws M2 5 x 5 mm screws 2 63PDH NOTICE When the hard drive is not in the computer store it in protective antistatic packaging See Protecting Against Electrostatic Discharge in your Product Information Guide 3 Slide the hard drive out of the computer 4 Remove the new drive from its packaging Save the original packaging to use when storing or shipping the hard drive NOTICE Use firm and even pressure to slide the drive into place If you force the hard drive into place using excessive force you may damage the connector 5 Press the hard drive cover down until it is fully seated in the bay and then replace and tighten the two screws 6 Use the Operating System CD to install the operating system for your computer 7 Use the Drivers and Utilities CD to install the drivers and utilities for your computer Back to Contents Page Back to Contents Page PC Card With Bluetooth Wireless Technology Dell Latitude D505 Service Manual A CAUTION Before performing the following procedures read the safety instruction
18. nd all attached devices NOTE Ensure that the computer is off and not in a power management mode If you cannot shut down the computer using the computer operating system press and hold the power button for 4 seconds If the computer is connected to a docking device docked undock it Disconnect the computer from the electrical outlet To avoid possible damage to the system board wait 10 to 20 seconds and then disconnect any attached devices Disconnect all other external cables from the computer Remove any installed PC Cards from the PC Card slot Close the display and turn the computer upside down on a flat work surface NOTI CE To avoid damaging the system board you must remove the main battery before you service the computer Slide and hold the battery bay latch release on the bottom of the computer and then remove the battery from the bay 11 Remove any installed memory modules Mini PCI cards and devices including a second battery if one is installed 12 Remove the hard drive Recommended Tools The procedures in this manual require the following tools e 1 Phillips screwdriver e Y4 inch flat blade screwdriver e Small plastic scribe e Flash BIOS update program floppy disk or CD Computer Orientation Screw Identification When you are removing and replacing components photocopy Screw Identification as a tool to lay out and keep track of the screws The placemat provides the number of
19. nstall the palm rest attach the right side of the palm rest first Back to Contents Page Back to Contents Page Docking Doors Dell Latitude D505 Service Manual Removing the Docking Doors A CAUTION Before working inside your computer read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Gently bend the docking doors and lift them away from the computer base docking doors 7R316 Installing the Docking Doors Slide the side of the docking doors with the spring over the longer posts docking doors with spring 7R316 alone Back to Contents Page Back to Contents Page Speakers Dell Latitude D505 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the display assembly 4 Remove the palm rest 5 Remove the speaker cable from the speaker cable
20. ooling assembly H1309 ejsmey feee ni ASL 13 keyboard i706 Back to Contents Page Back to Contents Page Reserve Battery Dell Latitude D505 Service Manual A CAUTION Before working inside your Dell computer read the safety instructions in your Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the battery 3 Depress the battery latch and rotate It out to remove the reserve battery cover reserve battery cover 6R456 4 Pull the reserve battery straight out of the computer base 5 Disconnect the reserve battery cable connector from the battery connector battery connector SS reserve battery 3R459 Back to Contents Page Back to Contents Page Hard Drive Dell Latitude D505 Service Manual A CAUTION If you remove the hard drive from the computer when the drive is hot do not touch the metal housing of the hard drive CAUTION Before working inside your computer read the safety instructions in your Product Information Guide NOTICE To prevent data loss shut down your computer before removing the hard drive Do not remove the hard drive while the computer is on in standby mode or in hiber
21. r by periodically touching an unpainted metal surface such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Turn the computer top side up and open it display see Mini RSL palm rest with touch pad D1482 3 Remove the center control cover a Open the display all the way 180 degrees so that it lies flat against your work surface b Starting on the right side of the computer use a plastic scribe to pry up the center control cover Lift it away from the computer and lay it aside 4 Remove the keyboard a Remove the two M2 5 x 5 mm screws across the top of the keyboard NOTICE The keycaps on the keyboard are fragile easily dislodged and time consuming to replace Be careful when removing and handling the keyboard b Rotate the keyboard up and slide it forward c Hold the keyboard up and slightly forward to allow access to the keyboard connector d Pull up on the keyboard connector tab to disconnect the keyboard connector from the system board M2 5 x 5 mm screws 2 63PDH keyboard connector NUN keyboard connector tab NE Ei NOTE When you replace the keyboard ensure that the keyboard tabs are completely in place to avoid scratching the palm rest Back to Contents Page Back to Contents Page Modem Dell Latitude D505 Service Manual Removing the Modem A CAUTION Before performing the following procedures read the safet
22. s You can do so by touching an unpainted metal surface Ei NOTE Memory modules purchased from Dell are covered under your computer warranty 1 Follow the instructions in Preparing to Work Inside the Computer 2 Turn the computer over loosen the captive screw labeled M from the memory module cover and lift the cover NOTICE To prevent damage to the memory module connector do not use tools to spread the securing clips that secure the memory module 3 If you are replacing a memory module remove the existing module NOTICE Handle memory modules by their edges and do not touch the components on a module a Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up b Remove the module from the connector NOTICE If you need to install memory modules in two connectors install a memory module in the connector labeled DIMM A slot 1 before you install a module in the other connector 4 Ground yourself and install the new memory module a Align the notch in the module with the slot in the center of the connector b Slide the edge of the module firmly into the connector and rotate the module down until you feel a click If you do not feel the click remove the module and reinstall it Ei NOTE If the memory module is not installed properly the computer does not boot No error message indicates this failure 5 Replace the cov
23. s in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the hard drive 3 Pull the connector of the PC Card with Bluetooth wireless technology out of the system board connector 4 Pull the cable to remove the PC Card with Bluetooth wireless technology from the computer NOTICE When replacing the PC Card with Bluetooth wireless technology ensure that the cable of the PC Card with Bluetooth wireless technology is routed correctly so that you do not damage the cable when you install the hard drive system board connector connector of PC Card with Bluetooth wireless technology a cable of PC Card with Bluetooth wireless technology 5x617 To replace a PC Card with Bluetooth wireless technology 1 Insert the PC Card with Bluetooth wireless technology 2 Ensure that the cable is routed under the tab tab 3 Connect the cable 4 Replace the hard drive Back to Contents Page Back to Contents Page Keyboard Dell Latitude D505 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap o
24. screws and their sizes H H m M2 x 3 mm M2 x 3mm M2xdmm M2x 5mm AF OE SPIR SEMKC 14784 Ho E M25xdmm M25x 5mm M245 x 8mm 6240E 63PDH 3A690 Optional Device Hard Drive Keyboard 1 each 2 each 2 each M2 x 3 mm FP 786 Modem 1 each i M2 x 3 mm 4 FOE Display Panel 8 each eoo M2 x 5 mm ABU Display Adapter Rails 14 1 inch display only 4 each i M2 x 3 mm 4 FOE Speakers 1 each M2 5 x 5 mm 63PDH Display Assembly 4 each os M2 5 x5 mm 63PDH Display Latch 1 each lt M2 x 5 mm 8U Fan 2 each M2 5 x 5 mm 63PDH Display Bezel display bumpers 6 each 6 each M2 x 5 mm BU Palm Rest 4 each MZ 5 x 5 mm 63PDH 13 each M25 x a mm 3RGO System Board 2 each M2 5 x 5 mm 63PDH 4 each M2 5 x 5 mm b3PDH Back to Contents Page M25 x 3 mm 3RGO MI x i mm SEMKC Back to Contents Page Memory Module Mini PCI Card and Devices Dell Latitude D505 Service Manual Memory Module Mini PCI Card Devices Memory Module A CAUTION Before working inside your Dell computer read the safety instructions in your Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic component
25. straight up and away from the computer base release button securing cps computer base Back to Contents Page Back to Contents Page Fan Dell Latitude D505 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the palm rest 4 Remove the microprocessor thermal cooling assembly 5 Pull straight up on the fan cable connector to disconnect it from the system board connector aje ECE E 2 3 fan cable connector po system board connector NN 6 Remove the two M2 5 x 8 mm screws from the fan and pull the fan away from the system board Back to Contents Page Back to Contents Page System Board Dell Latitude D505 Service Manual Removing the System Board A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer The system board s BIOS chip contains the Service Tag w
26. t grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer NOTICE Do not touch the processor die Press and hold the microprocessor down on the substrate on which the die Is mounted while turning the cam screw to prevent intermittent contact between the cam screw and microprocessor NOTICE To avoid damage to the microprocessor hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw 0 O O Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard NOTICE To ensure maximum cooling for the microprocessor do not touch the heat transfer areas on the microprocessor thermal cooling assembly The oils in your skin reduce the heat transfer capability of the thermal pads 3 Remove the microprocessor thermal cooling assembly NOTICE When removing the microprocessor module pull the module straight up Be careful not to bend the pins on the microprocessor module 4 To loosen the ZIF socket use a small flat blade screwdriver and rotate the ZIF socket cam screw counterclockwise until it comes to the cam stop 1 pin 1 corner ZIF socket NOTE The ZIF socket cam screw secures the microprocessor to the system board Take note of the arrow on the ZIF socket cam screw 5 Lift out the microprocessor module Installing the Microprocessor Module NOTICE Ensure that the cam lock is
27. tic discharge ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the display bezel 4 Remove the eight M2 x 5 mm screws from each side of the display panel 5 Lift the display panel and rotate the display panel out of the display cover 6 Press in both sides of the top flex cable connector and pull the top flex cable connector away from the display connector 7 Use the pull tab to disconnect the bottom flex cable connector from the inverter connector 1 pull tab on bottom flex cable connector 3 display connector inverter connector 2 top flex cable connector Display Latch NOTICE Disconnect the computer and any attached devices from electrical outlets and remove any installed batteries NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer 1 Remove the keyboard 2 Remove the display assembly 3 Remove the display bezel 4 Remove the M2 x 5 mm screw that secures the display bracket to the top cover 5 Lift the display bracket out of the top cover and then remove the display latch Ei NOTE Ensure that the display bracket is upright when you replace the display latch a aspiy seat Back to Contents Page Back to Contents Page
28. to a 90 degree angle and lift the display assembly up and out of the computer base 14 1 Inch Display 2 spi bumpers 6 K166 6 wa x s mm screws 16 14260 a ispay panei r1700 a wo x 3 mm screws ta a270E 15 Inch Display 1 M2 x 5 mm screws 6 1428U display panel D1724 2 display bumpers 6 K1681 H1375 3 display bezel H1370 6 M2 x 5 mm screws 8 1428U Display Bezel A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Remove the display assembly 4 Use a plastic scribe to pry the six display bumpers out of the screw holes located on the front of the bezel 5 Remove the six M2 x 5 mm screws located on the front of the bezel NOTICE Carefully separate the bezel from the top cover to avoid damage to the bezel 6 Starting at the bottom of the display panel by the DELL logo use your fingers to separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover Display Panel 14 1 Inch Display Panel A CAUTION Before performing the following procedures read the safety instructions in your Product Informatio
29. y instructions in your Product Information Guide NOTICE To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface Such as the back panel on the computer 1 Follow the instructions in Preparing to Work Inside the Computer 2 Remove the keyboard 3 Disconnect the display cable from the display cable connector on the system board 4 Remove the M2 x 3 mm screw eee ee Od 2 modem voz31 5 modem connector on system bonu a uexsmmscewfearoel 5 Pull up on the pull tab to disconnect the modem from the modem connector on the system board NOTICE Do not disconnect the modem cable from the system board 6 Disconnect the modem cable from the modem Installing the Modem 1 Connect the modem cable to the modem 2 Slip the left end of the modem and the modem cable underneath the metal modem securing clip NOTICE Ensure that the modem cable is routed correctly when you replace the modem 3 Ensure that the modem cable is properly routed under its routing clip NOTICE Do not press down on the left side of the modem while installing it 4 Align the connector on the bottom of the modem with the modem connector on the system board and then press down on the right side of the modem to seat both connectors rem 3 modem cable modem securing clip 5 Replace the M2 x 3 mm screw z E z 6 Reconnect the display c
Download Pdf Manuals
Related Search