Dell U2211H User's Manual
Contents
1. 1920 x 1080 resolution plus full screen support for lower resolutions Wide viewing angle to allow viewing from a sitting or standing position or while moving from side to side a Tilt swivel vertical extension and rotate adjustment capability m Removable pedestal and Video Electronics Standards Association VESA 100 mm mounting holes for flexible mounting solutions Plug and play capability if supported by your system m On Screen Display OSD adjustments for ease of set up and screen optimization m Software and documentation media includes an information file INF Image color Matching File ICM and product documentation Energy Saver feature for Energy Star compliance m Security lock slot m Asset Management Capability m Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality m EPEAT Silver Rating m Halogen Reduced Identifying Parts and Controls Front View Front View Front panel controls Back View Back view Back view with monitor stand Label Description Use VESA mounting holes 100 mm x 100 mm f 1 behind attached VESA Plate Wall mount monitor using VESA compatible wall mount kit 100 mm x 100 mm 2 Regulatory label Lists the regulatory approvals 3 Stand release button Release stand from monitor 4 Security lock slot Secures monitor with security cable lock 5 Dell Soundbar mounting brackets Attaches the optional Dell Soundbar2. 6 Barcode serial number label Refer to this label if you need to contact Dell for technical support USB downstream ports Connect your USB devices EJ Cable management slot Use to organize cables by placing them through the slot Side View USB downstream ports Left view Right view Bottom View INN Bottom view Bottom view with monitor stand ran ET Connect the USB cable that came with your monitor to the monitor and the USB upstream port computer Once this cable is connected you can use the USB connectors on the side and bottom of the monitor Connect your USB devices You can only use this connector after you have USB downstream ports connected the USB cable to the computer and USB upstream connector on the monitor Stand lock feature To lock the Stand to the Monitor Monitor Specifications Flat Panel Specifications Model U2211H U2311H Preset display area 475 2 H X 267 3 V mm Horizontal 475 2 mm 18 7 inches 178 vertical typical 178 vertical typical Viewing angle 178 horizontal typical 178 horizontal typical Luminance output 250 CD m2 typical 300 CD m typical 1000 to 1 typical 10000 to 1 typical Dynamic Contrast Contrast ratio 1000 to 1 typical 10000 to 1 typical Dynamic Contrast On On U2211H color gamut typical is based on CIE1976 82 and CIE1931 72 test standards U2311H color gamut typical is based on CIE1976 82 and
3. 2 Select the Settings tab 3 Select Advanced 4 Identify your graphics controller supplier from the description at the top of the window e g NVIDIA ATI Intel etc 5 Refer to the graphic card provider website for updated driver for example http www ATIl com OR http www NVIDIA com 6 After installing the drivers for your Graphics Adapter attempt to set the resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H again In Windows Vista or Windows 7 Pp Right click on the desktop and click Personalization 2 Click Change Display Settings 3 Click Advanced Settings 4 Identify your graphics controller supplier from the description at the top of the window e g NVIDIA ATI Intel etc 5 Refer to the graphic card provider website for updated driver for example http www ATl com OR http www NVIDIA com 6 After installing the drivers for your Graphics Adapter attempt to set the resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H again K NOTE U2211H If you are unable to set the resolution to 1920 x 1080 please contact the manufacturer of your computer or consider purchasing a graphics adapter that will support the video resolution of 1920 x 1080 U2311H If you are unable to set the resolution to 1920 x 1080 please contact the manufacturer of your computer or consider purchasing a graphics adapter that will support the video resolution of 1920 x 1080 Back to Contents
4. 1080 for U2211H or 1920 x 1080 for U2311H as an option you may need to update your graphics driver Please choose the scenario below that best describes the computer system you are using and follow the provided directions 1 If you have a Dell desktop or a Dell portable computer with internet access 2 If you have a non Dell desktop portable computer or graphics card Back to Contents Page Dell U2211H U2311H Monitor User Guide Setting the display resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H maximum Information in this document is subject to change without notice 2010 Dell Inc All rights reserved Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell and the DELL logo are trademarks of Dell Inc Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Intel is a registered trademark of Intel Corporation in the U S and other countries and ATI is a trademark of Advanced Micro Devices Inc ENERGY STAR is a registered trademark of the U S Environmental Protection Agency As an ENERGY STAR partner Dell Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks a
5. CIE1931 72 test standards Resolution Specifications Horizontal scan range Vertical scan range Supported Video Modes U2211H 480p 576p 720p 1080p 480i 576i 1080i Video display capabilities DVI DP playback Preset Display Modes U2211H Display Mode da Vertical Frequency Hz Pixel Clock MHz Sync Polarity Horizontal Vertical VESA 720 x 400 31 5 70 0 28 3 VESA 640 x 480 31 5 60 0 25 2 VESA 640 x 480 37 5 75 0 31 5 VESA 800 x 600 37 9 60 3 40 0 VESA 800 x 600 46 9 75 0 49 5 VESA 1024 x 768 48 4 60 0 65 0 VESA 1024 x 768 60 0 75 0 78 8 VESA 1152 x 864 67 5 75 0 108 0 VESA 1280 x 1024 64 0 60 0 108 0 VESA 1280 x 1024 80 0 75 0 135 0 VESA 1600 x 1200 75 0 60 0 162 0 VESA 1920 x 1080 67 5 60 0 148 5 U2311H Display Mode O Vertical Frequency Hz Pixel Clock MHz Sync Polarity Horizontal Vertical VESA 720 x 400 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 ijg 1600 x 1200 1920 x 1080 Electrical Specifications U2211H U2311H Analog RGB 0 7 Volts 5 positive polarity at 75 ohm input impedance Video input signals Digital DVI D TMDS 600mV for each differential line positive polarity at 50 ohm input impedance DP 1 1a signal input support TTL levels required and s
6. a lightly dampened warm cloth to clean the monitor Avoid using detergent of any kind as some detergents leave a milky film on the monitor If you notice white powder when you unpack your monitor wipe it off with a cloth Handle your monitor with care as a darker colored monitor may scratch and show white scuff marks more than a lighter colored monitor To help maintain the best image quality on your monitor use a dynamically changing screen saver and turn off your monitor when not in use Back to Contents Page Back to Contents Page Appendix Dell U2211H U2311H Monitor User s Guide Safety Instructions FCC Notice U S Only and Other Regulatory Information Contacting Dell warni NG Safety Instructions A WARNING Use of controls adjustments or procedures other than those specified in this documentation may result in exposure to shock electrical hazards and or mechanical hazards For information on safety instructions see the Product Information Guide FCC Notices U S Only and Other Regulatory Information For FCC notices and other regulatory information see the regulatory compliance website located at www dell com regulatory compliance Contacting Dell For customers in the United States call 800 WWW DELL 800 999 3355 K NOTE If you do not have an active Internet connection you can find contact information on your purchase invoice packing slip bill or Dell product catalog Dell
7. connector Push to select the VGA input source Dell U2X11H Brightness Contrast Input Color Format vna Auto Adjust Input Source Mode Selection Preset Modes Display Settings Reset Color Settings Other Settings Personalize on 1920 x 1080 60H Gamma Allows you to set the color mode to PC or MAC Dell U2X11H S Brightness Contrast Input Color Format Input Source Mode Selection 4 Preset Modes Display Settings Reset Color Settings Other Settings Personalize E O Resolution 1920 x 1080 0 60H Mode Selection You can choose Graphics or Video according to the input signal Graphics Select this mode if your monitor is connected to your computer Video Select this mode if your monitor is connected to a DVD player Preset Modes When you select Graphics you can choose Standard Multimedia Game Warm Cool or Custom RGB Standard Loads the monitor s default color settings This is the default preset mode Multimedia Loads color settings ideal for multimedia applications Game Loads color settings ideal for most gaming applications Warm Increase the color temperature The screen appears warmer with a red yellow tint Cool Decreases the color temperature The screen appears cooler with a blue tint Vv and v buttons to adjust the three Custom RGB Allows you to manually adjust the color settings Press the R G B values and crea
8. or the black DisplayPort cables to the computer at the same time All monitors ship with the VGA blue cable attached by default 2 Connect the white digital DVI D or the blue analog VGA or the black DisplayPort display connector cable to the corresponding video port on the back of your computer Do not use the three cables on the same computer Use all the cables only when they are connected to three different computers with appropriate video systems Connecting the white DVI cable E Connecting the blue VGA cable MU Er Connecting the black DisplayPort cable A CAUTI ON The Graphics are used for the purpose of illustration only Appearance of the computer may vary Connecting the USB cable After you have completed connecting the DVI VGA DP cable follow the procedure below to connect the USB cable to the computer and complete your monitor setup 1 Connect the upstream USB port cable supplied to an appropriate USB port on your computer See bottom view for details 2 Connect USB peripherals to the downstream USB ports side or bottom on the monitor See side or bottom view for details 3 Plug the power cables for your computer and monitor into a nearby outlet 4 Turn on the monitor and the computer If your monitor displays an image installation is complete If it does not display an image see Solving Problems 5 Use the cable slot on the monitor stand to organize the cables Organizing Your Cabl
9. trademarks and trade names other than its own Model U2211Ht U2311Hb May 2010 Rev A01 Back to Contents Page About Your Monitor Dell U2211H U2311H Monitor User s Guide Package Contents Product Features identifying Parts and Controls Monitor Specifications Plug and Play Capability Universal Serial Bus USB Interface LCD Monitor Quality and Pixel Policy Maintenance Guidelines Package Contents Your monitor ships with the components shown below Ensure that you have received all the components and contact Dell if something is missing K NOTE Some items may be optional and may not ship with your Monitor Some features or media may not be available in certain countries K NOTE To set up with any other stand please refer to the respective stand setup guide for setup instructions Monitor Stand Power Cable VGA Cable attached to the monitor DVI Cable USB up stream cable enables the USB ports on the monitor Drivers and Documentation media Quick Setup Guide Product and Safety Information Guide Product Features The U2211H U2311H flat panel display has an active matrix thin film transistor TFT liquid crystal display LCD The monitor features include m 546 1 mm 21 5 inch viewable area display Measured diagonally 1920 x 1080 resolution plus full screen support for lower resolutions m 584 2 mm 23 inch viewable area display Measured diagonally
10. 90 mm 11 02 inches Depth 184 10 mm 7 25 inches 184 10 mm 7 25 inches Weight Weight with packaging 16 85 lbs 7 65 kg 18 14 Ibs 8 23 kg Weight with stand assembly and cables 14 22 lbs 6 45 kg 15 45 Ibs 7 01 kg Weight without stand assembly For wall mount or VESA mount considerations 9 97 Ibs 4 52 kg 10 34 Ibs 4 69 kg no cables Weight of stand assembly 3 88 lbs 1 76 kg 4 06 Ibs 1 84 kg Environmental Characteristics Model U2211H U2311H Operating 0 to 40 C 0 to 40 C Nen beratin Storage 20 to 60 C 4 to 140 F Storage 20 to 60 C 4 to 140 F P 9 Shipping 20 to 60 C 4 to 140 F Shipping 20 to 60 C 4 to 140 F Humidity Operating 10 to 80 non condensing 10 to 80 non condensing Storage 5 to 90 non condensing Storage 5 to 90 non condensing Shipping 5 to 90 non condensing Shipping 5 to 90 non condensing Operating 4 850 m 15 902 ft max 4 850 m 15 902 ft max Non operating Non operating 12 192 m 40 000 ft max 12 192 m 40 000 ft max 187 67 BTU hour maximum 235 44 BTU hour maximum Thermal dissipation 75 07 BTU hour typical 112 60 BTU hour typical Power Management Modes If you have VESA s DPM compliance display card or software installed in your PC the monitor can automatically reduce its power consumption when not in use This is referred to as Power Save Mode If the computer detects inp
11. Dell U2211H U2311H Monitor User s Guide About Your Monitor Setting Up the Monitor Operating the Monitor Troubleshooting Appendix Notes Notices and Cautions E4 NOTE A NOTE indicates important information that helps you make better use of your computer Z CAUTION A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem WARNING A WARNING indicates a potential for property damage personal injury or death Information in this document is subject to change without notice O 2010 Dell Inc All rights reserved Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell and the DELL logo are trademarks of Dell Inc Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Intel is a registered trademark of Intel Corporation in the U S and other countries and ATI is a trademark of Advanced Micro Devices Inc ENERGY STAR is a registered trademark of the U S Environmental Protection Agency As an ENERGY STAR partner Dell Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Inc disclaims any proprietary interest in
12. Inspect the display for any abnormalities Repeat steps 5 and 6 to inspect the display in green blue black white screens The test is complete when the white screen appears To exit press the Button 4 again If you do not detect any screen abnormalities upon using the built in diagnostic tool the monitor is functioning properly Check the video card and computer Common Problems The following table contains general information about common monitor problems you might encounter and the possible solutions What You Experience Possible Solutions Ensure that the video cable connecting the monitor and the computer is properly Common Symptoms No Video Power LED off No Video Power LED on Poor Focus Shaky Jittery Video Missing Pixels Stuck on Pixels Brightness Problems Geometric Distortion Horizontal Vertical Lines Synchronization Problems Safety Related Issues Intermittent Problems No picture No picture or no brightness Picture is fuzzy blurry or ghosting Wavy picture or fine movement LCD screen has spots LCD screen has bright spots Picture too dim or too bright Screen not centered correctly Screen has one or more lines Screen is scrambled or appears torn Visible signs of smoke or sparks Monitor malfunctions on amp off connected and secure Verify that the power outlet is functioning properly using any other electrical equipment Ensure that the power button is depresse
13. Page Back to Contents Page Operating the Monitor Dell U2211H U2311H Monitor User s Guide Using the Front Panel Controls Using the On Screen Display OSD Menu Setting the Maximum Resolution Using the Dell Soundbar Optional Using the Tilt Swivel and Vertical Extension Rotating the monitor Adjusting the Rotation Display Settings of Your System Using the Front Panel Use the control buttons on the front of the monitor to adjust the characteristics of the image being displayed As you use these buttons to adjust the controls an OSD shows the numeric values of the characteristics as they change The following table describes the front panel buttons 1 Use this button to choose from a list of preset color modes Shortcut key Preset Modes 2 Use this button to directly access the Brightness Contrast menu Shortcut key Brightness Contrast 3 Use the MENU button to launch the on screen display OSD and select the OSD Menu See Accessing the Menu System 4 x Use this button to go back to the main menu or exit the OSD main menu Exit o Use the Power button to turn the monitor on and off The Blue LED indicates the monitor is on and fully functional An amber LED indicates DPMS power save mode Power with power light indicator Using the On Screen Display OSD Menu Accessing the Menu System K NOTE If you change the settings and then either proceed to another menu or exit t
14. Solutions No Sound No power to Soundbar the Turn the Power Volume knob on the Soundbar clockwise to the middle position check if power indicator is off the power indicator Blue LED on the front of the Soundbar is illuminated Confirm that the power cable from the Soundbar is plugged into the adapter No Sound Soundbar has power power Plug the audio line in cable into the computer s audio out jack indicator is on Set all Windows volume controls to their maximum Play some audio content on the computer i e audio CD or MP3 Turn the Power Volume knob on the Soundbar clockwise to a higher volume setting Clean and reseat the audio line in plug Test the Soundbar using another audio source i e portable CD player Distorted Sound Computer s sound card is used Clear any obstructions between the Soundbar and the user as the audio source Confirm that the audio line in plug is completely inserted into the jack of the sound card Set all Windows volume controls to their midpoints Decrease the volume of the audio application Turn the Power Volume knob on the Soundbar counter clockwise to a lower volume setting Clean and reseat the audio line in plug Troubleshoot the computer s sound card Test the Soundbar using another audio source i e portable CD player Distorted Sound Unbalanced Sound Output Low Volume Back to Contents Page Other audio source is used Sound from only one side of Soundbar Volume is too low C
15. VI D input the positioning adjustments are not available Reset the monitor to Factory Settings Perform Auto Adjust via OSD Adjust Phase and Pixel Clock controls via OSD Perform monitor self test feature check and determine if these lines are also in self test mode Check for bent or broken pins in the video cable connector Run the built in diagnostics NOTE When using DVI D input the Pixel Clock and Phase adjustments are not available Reset the monitor to Factory Settings Perform Auto Adjust via OSD Adjust Phase and Pixel Clock controls via OSD Perform monitor self test feature check to determine if the scrambled screen appears in self test mode Check for bent or broken pins in the video cable connector Restart the computer in the safe mode Do not perform any troubleshooting steps Contact Dell immediately Ensure that the video cable connecting the monitor to the computer is connected properly and is secure Reset the monitor to Factory Settings Perform monitor self test feature check to determine if the intermittent problem occurs in self test mode Missing Color Picture missing color Perform monitor self test feature check Ensure that the video cable connecting the monitor to the computer is connected properly and is secure Check for bent or broken pins in the video cable connector Picture color not good Change the Color Setting Mode in the Color Settings OSD to Graphics or Video depending on
16. appearance of the video image NOTE Saturation adjustment is available only for video input Reset your monitor color settings to the factory settings Use the Display Settings to adjust image Dell U2X11H Brightness Contrast Wide Mode Auto Adjust Horizontal Position Input Source Vertical Position Color Settings Sharpness tin Pixel Clock Other Settings Phase Personalize Reset Display Settings tesolution 1920 x 1080 tb Back to Contents Page Setting Up Your Monitor Dell U2211H U2311H Monitor Setting the display resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H maximum For maximum display performance with Microsoft Windows operating systems set the display resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H pixels by performing the following steps In Windows XP 1 Right click on the desktop and click Properties 2 Select the Settings tab 3 Move the slider bar to the right by pressing and holding the left mouse button and adjust the screen resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H 4 Click OK In Windows Vista or Windows 7 1 Right click on the desktop and click Personalization 2 Click Change Display Settings 3 Move the slider bar to the right by pressing and holding the left mouse button and adjust the screen resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H 4 Click OK If you do not see 1920 x
17. ble DDC clock Pin 24 pin Side of the Connected Signal Cable TMDS RX2 TMDS RX2 TMDS Ground Floating Floating DDC Clock DDC Data Floating TMDS RX1 TMDS RX1 TMDS Ground Floating Floating 5V 3 3V power Self test Hot Plug Detect TMDS RXO TMDS RXO TMDS Ground Floating Floating TMDS Ground TMDS Clock TMDS Clock DisplayPort Connector ee 2 20 Pin 20 pin Side of the Connected Signal Cable Number 1 MLO p 3 MLO n 4 ML1 p 5 GND 6 ML1 n 8 GND 9 ML2 n 10 ML3 p 11 GND 12 ML3 n 13 GND 14 GND 15 AUX p 16 GND 17 AUX n 18 HPD 19 DP_PWR Return 20 av oP rm Plug and Play Capability You can install the monitor in any Plug and Play compatible system The monitor automatically provides the computer system with its Extended Display Identification Data EDID using Display Data Channel DDC protocols so the system can configure itself and optimize the monitor settings Most monitor installations are automatic you can select different settings if desired For more information about changing the monitor settings see Operating the Monitor Universal Serial Bus USB Interface This section gives you information about the USB ports that are available on the left side of your monitor K NOTE This monitor supports High Speed Certified USB 2 0 interface Transfer speed Data Rate Power Consumption High speed 480 Mbps 2 5W Max each port Full spe
18. ble flat table Remove the stand Use a screwdriver to remove the four screws securing the plastic cover Attach the mounting bracket from the wall mounting kit to the LCD Mount the LCD on the wall by following the instructions that came with the base mounting kit 0 UnA K NOTE For use only with UL Listed Wall Mount Bracket with minimum weight load bearing capacity of 4 52 kg Back to Contents Page Back to Contents Page Troubleshooting Dell U2211H U2311H Monitor User s Guide Self lest Built in Diagnostics Common Problems Product Specific Problems Universal Serial Bus Specific Problems Dell Soundbar Problems WARNING Before you begin any of the procedures in this section follow the Safety Instructions Self Test Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly If your monitor and computer are properly connected but the monitor screen remains dark run the monitor self test by performing the following steps 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer To ensure proper Self Test operation remove all Digital white connector and the Analog blue connector cables from the back of computer 3 Turn on the monitor The floating dialog box should appear on screen against a black background if the monitor cannot sense a video signal and is working correctly While in self test mo
19. d fully Ensure that the correct input source is selected via the Input Source Select button Increase brightness amp contrast controls via OSD Perform monitor self test feature check Check for bent or broken pins in the video cable connector Run the built in diagnostics Ensure that the correct input source is selected via the Input Source Select button Perform Auto Adjust via OSD Adjust the Phase and Pixel Clock controls via OSD Eliminate video extension cables Reset the monitor to Factory Settings Change the video resolution to the correct aspect ratio 16 9 Perform Auto Adjust via OSD Adjust the Phase and Pixel Clock controls via OSD Reset the monitor to Factory Settings Check environmental factors Relocate the monitor and test in another room Cycle power on off Pixel that is permanently off is a natural defect that can occur in LCD technology For more information on Dell Monitor Quality and Pixel Policy see Dell Support site at support dell com Cycle power on off Pixel that is permanently off is a natural defect that can occur in LCD technology For more information on Dell Monitor Quality and Pixel Policy see Dell Support site at support dell com Reset the monitor to Factory Settings Auto Adjust via OSD Adjust brightness amp contrast controls via OSD Reset the monitor to Factory Settings Auto Adjust via OSD Adjust horizontal amp vertical controls via OSD NOTE When using D
20. de the power LED remains green Also depending upon the selected input one of the dialogs shown below will continuously scroll through the screen Dell U2X11H pa Dell U2X11H No YGA Cable No DVI D Cable No DisplayPort Cable CEP gt 1 This box also appears during normal system operation if the video cable becomes disconnected or damaged 2 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after you use the previous procedure check your video controller and computer because your monitor is functioning properly Built in Diagnostics Your monitor has a built in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor or with your computer and video card K NOTE You can run the built in diagnostics only when the video cable is unplugged and the monitor is in self test mode To run the built in diagnostics APNEA ANS Ensure that the screen is clean no dust particles on the surface of the screen Unplug the video cable s from the back of the computer or monitor The monitor then goes into the self test mode Press and hold the Button 1 and Button 4 on the front panel simultaneously for 2 seconds A gray screen appears Carefully inspect the screen for abnormalities Press the Button 4 on the front panel again The color of the screen changes to red
21. ed 12 Mbps 2 5W Max each port Low speed 1 5 Mbps 2 5W Max each port USB Upstream Connector 12 USB Downstream Connector USB Ports 1 upstream back 4 downstream 2 on back 2 on left side K NOTE USB 2 0 functionality requires a USB 2 0 capable computer K NOTE The monitor s USB interface works only when the monitor is on or in power save mode If you turn off the monitor and then turn it on the attached pe take a few seconds to resume normal functionality LCD Monitor Quality and Pixel Policy During the LCD Monitor manufacturing process it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and do not affect the display quality or usability For more information on Dell Monitor Quality and Pixel Policy see Dell Support site at support dell com Maintenance Guidelines Cleaning Your Monitor Ax WARNING Read and follow the safety instructions before cleaning the monitor Ax WARNING Before cleaning the monitor unplug the monitor power cable from the electrical outlet For best practices follow the instructions in the list below while unpacking cleaning or handling your monitor To clean your antistatic screen lightly dampen a soft clean cloth with water If possible use a special screen cleaning tissue or solution suitable for the antistatic coating Do not use benzene thinner ammonia abrasive cleaners or compressed air Use
22. eparate syncs including Trigger points SOG Composite SYNC on green AC impar 100 to 240 VAC 50 or 60 Hz 3 Hz 1 5 A Typical voltage frequency current Inrush current 120 V 30 A Max 240 V 60 A Max Physical Characteristics Model U2211H U2311H 15 pin D subminiature blue connector 15 pin D subminiature blue connector Connector type DVI D white connector DP black DVI D white connector DP black connector connector Synchronization input signals Digital Detachable DVI D Solid pins Digital Detachable DVI D Solid pins shipped detached from the monitor shipped detached from the monitor Signal cable type Analog attachable D Sub 15pins Analog attachable D Sub 15pins shipped attached to the monitor shipped attached to the monitor Dimensions with stand Height extended 447 6 mm 17 62 inches 456 16 mm 17 96 inches Height compressed 347 6 mm 13 69 inches 356 16 mm 14 02 inches Width 514 4 mm 20 25 inches 547 97 mm 21 57 inches Depth 184 1 mm 7 25 inches 184 1 mm 7 25 inches Dimensions without stand Height 305 9 mm 12 04 inches 325 07 mm 12 80 inches Width 514 4 mm 20 25 inches 547 97 mm 21 57 inches Depth 65 00 mm 2 56 inches 65 00 mm 2 56 inches Stand dimensions Height extended 363 60 mm 14 31 inches 370 47 mm 14 59 inches Height compressed 323 50 mm 12 74 inches 331 32 mm 13 04 inches Width 279 90 mm 11 02 inches 279
23. es After attaching all necessary cables to your monitor and computer See Connecting Your Monitor for cable attachment use the cable management slot to organize all cables as shown above Attaching the Soundbar Optional CAUTION Do not use with any device other than the Dell Soundbar K NOTE The Soundbar power connector 12 V DC output is for the optional Dell Soundbar only To attach the Soundbar Working from the back of the monitor attach the Soundbar by aligning the two slots with the two tabs along the bottom of the monitor Slide the Soundbar to the left until it snaps into place Connect the Soundbar with the DC power connector Insert the mini stereo plug from the back of the Soundbar into the computer s audio output jack Removing the Stand K NOTE To prevent scratches on the LCD screen while removing the stand ensure that the monitor is placed on a soft clean surface EA NOTE This is applicable for a monitor with a stand When other stand is bought please refer to the respective stand setup guide for set up instructions To remove the stand 1 Place the monitor on a flat surface 2 Press and hold the Stand release button 3 Lift the stand up and away from the monitor Wall Mounting Optional Screw dimension M4 x 10 mm Refer to the instructions that come with the VESA compatible base mounting kit Place the monitor panel on a soft cloth or cushion on a sta
24. he OSD menu the monitor automatically saves those changes The changes are also saved if you change the settings and then wait for the OSD menu to disappear 1 Push the El button to launch the OSD menu and display the main menu Main Menu for analog VGA Input Dell U2X11H Brightness Auto Adjust Contrast Input Source Color Settings Display Settings Other Settings Person lize 1 1920 x 1080 or Main Menu for digital DVI Input Menu Dell U2X11H PE AAA Brightness Contrast Input Source Color Settings Display Settings Other Settings Personalize 1920 x 1080 or Main Menu for display DP Input Dell U2X11H Brightness Contrast Input Source Color Settings Display Settings Other Settings Person lize tesolution 1920 x 1080 601 KANOTE Auto Adjust is only available when you use the analog VGA connector A 2 Push the A and buttons to move between the setting options As you move from one icon to another the option name is highlighted See the following table for a complete list of all the options available for the monitor 3 Push the button once to activate the highlighted option 4 Push and button to select the desired parameter 5 Push to enter the slide bar and then use the and buttons according to the indicators on the menu to make your changes vg 6 Select the pe button to return to the main menu Submenus Brightness Contrast Use this menu to activate Brig
25. htness Contrast adjustment Dell U2X11H Brightness Auto Adjust Contrast Input Source Color Settings Display Settings Other Settings Person lize 1 1920 x 1080 60 60Hz Brightness Brightness adjusts the luminance of the backlight A Push the button to increase brightness and push the button to decrease brightness min 0 max 100 Contrast Adjust Brightness first and then adjust Contrast only if further adjustment is necessary A Vv Push the button to increase contrast and push the button to decrease contrast min 0 max 100 The Contrast function adjusts the degree of difference between darkness and lightness on the monitor screen Dynamic Contrast Dynamic Contrast adjusts the contrast ratio to 10000 1 Push the button to select the Dynamic Contrast On or Off Note Dynamic Contrast provides higher contrast if you choose Game preset Movie Preset Sports Preset and Nature F Auto Adjust Even though your computer recognizes your monitor on startup the Auto Adjustment function optimizes the display settings LP with your particular setup Auto Adjustment allows the monitor to self adjust to the incoming video signal After using Auto Adjustment you can further t your monitor by using the Pixel Clock Coarse and Phase Fine controls under Image Settings Auto Adjustment in Progr NOTE In most cases Auto Adjust produces the best image for your configuration NOTE Auto Adjust option is only ava
26. ideo media No Composite input signal or Check whether the signal cable is plugged in properly Re plug the signal cable if No Component input signal necessary appears Reset the computer or video player The picture does not fill the The picture cannot fill the Due to different video formats aspect ratio of DVDs the monitor may display in full entire screen height or width of the screen screen Run the built in diagnostics K NOTE When choosing DVI D mode the Auto Adjust function will not be available Universal Serial Bus USB Specific Problems pecific Sym perience Possible Solutions USB interface is not working USB peripherals are not Check that your monitor is turned ON working Reconnect the upstream cable to your computer Reconnect the USB peripherals downstream connector Switch off and then turn on the monitor again Reboot the computer Some USB devices like external portable HDD require higher electric current connect the device directly to the computer system High Speed USB 2 0 interface isjHigh Speed USB 2 0 Check that your computer is USB 2 0 capable peripherals working slowly or Some computers have both USB 2 0 and USB 1 1 ports Ensure that the correct USB port not working at all is used Reconnect the upstream cable to your computer Reconnect the USB peripherals downstream connector Reboot the computer Dell Soundbar Problems Common Symptoms What You Experience Possible
27. ilable when you are using the analog VGA connector Use the Input Source menu to select between different video signals that may be connected to your monitor Dell U2X11H l Brightness Contrast Y Auto Select Auto Adjust VGA DVI D E Color Settings DisplayPort Display Settings Other Settings Personalize Resolution 1920 x 1080 60H Auto Select omp Auto Select Push to select the Auto Select the monitor will auto detect either VGA input or DVI D input or DislpayPort input A DVI D Select DVI D input when you are using the Digital DVI connector Push to select the DVI input source DisplayPort Select DisplayPort input when you are using the DisplayPort DP connector Push to select the DisplayPort input source EA Color Settings Use the Color Settings to adjust the color setting mode and color temperature There are different color setting sub menus for VGA DVI D and Video input Dell U2X11H l Brightness Contrast Fr olor F Auto Adjust Gamma PC Input Source Mode Selection Graphics Preset Modes p Standard Display Settings Reset Color Settings Other Settings Personalize Resolution 1920 x 1080 60H Input Color Format Choose the RGB option if monitor is connected to a computer or a DVD using a VGA or DVI cable Choose the YPbPr option if m connected to a DVD by a YPbPr to VGA or YPbPr to DVI cable or if the DVD color output setting is not RGB Select VGA input when you are using the analog VGA
28. lear any obstructions between the Soundbar and the user Confirm that the audio line in plug is completely inserted into the jack of the audio source Decrease the volume of the audio source Turn the Power Volume knob on the Soundbar counter clockwise to a lower volume setting Clean and reseat the audio line in plug Clear any obstructions between the Soundbar and the user Confirm that the audio line in plug is completely inserted into the jack of the sound card or audio source Set all Windows audio balance controls L R to their midpoints Clean and reseat the audio line in plug Troubleshoot the computer s sound card Test the Soundbar using another audio source i e portable CD player Clear any obstructions between the Soundbar and the user Turn the Power Volume knob on the Soundbar clockwise to the maximum volume setting Set all Windows volume controls to their maximum Increase the volume of the audio application Test the Soundbar using another audio source i e portable CD player
29. nd names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Model U2211Ht U2311Hb May 2010 Rev A01 Back to Contents Page Setting Up the Monitor Dell U2211H U2311H Monitor User s Guide Attaching the Stand Connecting the Monitor Organizing Your Cables Attaching the Soundbar optional Removing the Stand Wall Mounting Optional Attaching the Stand K NOTE The stand is detached when the monitor is shipped from the factory K NOTE This is applicable for a monitor with a stand When other stand is bought please refer to the respective stand setup guide for set up instructions To attach the monitor stand 1 Remove the cover and place the monitor on it 2 Fit the two tabs on the upper part of the stand to the groove on the back of the monitor 3 Press the stand till it snaps into its place Connecting Your Monitor A WARNING Before you begin any of the procedures in this section follow the Safety Instructions To connect your monitor to the computer 1 Turn off your computer and disconnect the power cable Connect the blue VGA cable from your monitor to your computer 4 NOTE If your computer supports a white DVI connector unscrew and detach the blue VGA cable from the monitor and then connect the White DVI cable to the monitor and the white DVI connector on your computer K NOTE Do not connect the blue VGA the white DVI
30. provides several online and telephone based support and service options Availability varies by country and product and some services may not be available in your area To contact Dell for sales technical support or customer service issues Visit support dell com Verify your country or region in the Choose A Country Region drop down menu at the bottom of the page Click Contact Us on the left side of the page Select the appropriate service or support link based on your need Choose the method of contacting Dell that is convenient for you Back to Contents Page Back to Contents Page Setting Up Your Monitor Dell U2211H U2311H Monitor If you have a Dell desktop or a Dell portable computer with internet access 1 Go to http support dell com enter your service tag and download the latest driver for your graphics card 2 After installing the drivers for your Graphics Adapter attempt to set the resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H again K NOTE If you are unable to set the resolution to 1920 x 1080 for U2211H or 1920 x 1080 for U2311H please contact Dell to inquire about a Graphics Adapter that supports these resolutions Back to Contents Page Back to Contents Page Setting Up Your Monitor Dell U2211H U2311H Monitor If you have a non Dell desktop portable computer or graphics card In Windows XP Pp Right click on the desktop and click Properties
31. te your own preset color mode Dell U2X11H Brightness Contrast Input Color Format Auto Adjust Gamma m Y Input Source Mode Selection Multimedia Preset Modes Game Display Settings Reset Color Settings Warm Other Settings Cool O Personalize Custom RGB on 1920 x 108 When you select Video you can choose Movie Game Sports or Nature preset Movie Loads color settings ideal for movies This is the default preset mode Game Loads color settings ideal for game Sports Loads color settings ideal for sports Nature Loads color settings ideal for nature Dell U2X11H Brightness Contrast Input Color Format Auto Adjust Input Source Mode Selection Preset Modes Display Settings Other Settings Saturation E O Personalize Reset Color Settings Resolution 1920 x 1080 60Hz Hue This feature can shift color of video image to green or purple This is used to adjust the desired flesh tone color Use A or adjust the hue from 0 to 100 Reset Color Setting s Display Settings A Press E to increase the green shade of the video image Vv Press to increase the purple shade of the video image NOTE Hue adjustment is available only for video input This feature can adjust the color saturation of the video image Use or to adjust the saturation from 0 to 100 Press to increase the monochrome appearance of the video image Vv Press to increase the colorful
32. the application Try different Color Preset Settings in Color Settings OSD Adjust R G B value in Color Settings OSD if the Color Management is turned off Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD Run the built in diagnostics Image retention from a static Faint shadow from the static Use the Power Management feature to turn off the monitor at all times when not in use image left on the monitor for a Jimage displayed appears on for more information see Power Management Modes long period of time the screen Alternatively use a dynamically changing screensaver Product Specific Problems Specific Symptoms What You Experience Possible Solutions Screen image is too small Image is centered on screen Check the Scaling Ratio setting in Image Setting OSD but does not fill entire viewing Reset the monitor to Factory Settings area Cannot adjust the monitor with OSD does not appear on the Turn off the monitor unplug the power cord plug back and then turn on the monitor the buttons on the front panel screen No Input Signal when user No picture the LED light is Check the signal source Ensure the Computer is not in the power saving mode by controls are pressed green When you press moving the mouse or pressing any key on the keyboard or Menu key the message Check to make sure Video Source to S Video Composite or Component is powered and No S Video input signal or playing v
33. ut from keyboard mouse or other input devices the monitor automatically resumes functioning The following table shows the power consumption and signaling of this automatic power saving feature U2211H VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption Normal Active Active Active Blue 55W maximum operation 22W typical Active off mode Inactive Inactive Blanked Amber Less than 1 0 W Switch off Off Less than 1 0 W U2311H VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption Normal operationActive Active Active Blue 69W maximum 33W typical Active off mode Inactive Inactive Blanked Amber Less than 1 0 W Switch off Off Less than 1 0 W The OSD will only function in the normal operation mode When any button is pressed in Active off mode one of the following messages will be displayed Dell U2X11H There is no signal coming from your computer Press any key on the keyboard or mouse to wake it up To change to another input source press the monitor button again TER Activate the computer and the monitor to gain access to the OSD E4 NOTE This monitor is ENERGY STAR compliant ENERGY STAR Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor Maximum power consumption with max luminance Dell Soundbar and USB active Pin Assignments VGA Connector 15 pin Side of the Connected Signal Ca
Download Pdf Manuals
Related Search