Dakota Digital MCL-30K-SPD User's Manual
Contents
1. Zz Vozi WWW DAKOTADIGITAL COM MCL 30K SPD Thank you for purchasing the Dakota Digital MCL 30K SPD gauge for your Harley Davidson Touring bike This is designed to be a replacement for all touring models from 1996 2003 This is part of a six gauge package for touring models so you can add additional gauges as you choose IMPORTANT NOTE This gauge has an odometer preset option that is only available for the first 100 miles 160km of operation See preset odometer for instructions INSTALLATION First read and familiarize yourself with all of the components and this manual The first step is to remove the seat and disconnect the negative side of the battery as with any electronic install Once the battery is disconnected you are ready to start Remove the outer fairing for FLHT models this will vary from model to model please follow the service manual to expose the wiring and gauges Road Glide FLTR models will not need the outer fairing removed Remove Factory Gauges Now you are ready to start unplugging and removing the original speedometer ULTRA FLHT batwing fairings Remove the clamps that hold the Speed and Tach in place with a screw driver or wrench depending on application and remove the gauges 1 MAN 650334 A ROAD GLIDE FLTR You will need to remove the speedometer and tachometer instrument bezel To do this remove two small screws on the left and right side of the bezel Then lift up on the back2. Common problems during calibration gt VSS vehicle speed sensor wires should be isolated from the ignition system Coils plug wires or tachometer signal wires routed near or with the VSS wire can cause many problems If you are seeing erratic speedometer operation registering speed at a standstill or speed changes with engine RPM please double check your VSS wire and tachometer wire routing making sure the VSS wire is separated from any ignition system components gt If your speedometer registers JQ all the time the unit is not receiving a VSS signal please double check your sensor wiring and mounting The speedometer cannot be properly calibrated until you are registering a stable but possibly incorrect soeedometer reading gt Please see Speed sensor voltage checks on the last page for assistance in checking your sensor 5 MAN 650334 A Speedometer Setup Continued 5 5Et Miles to Next Service setup The service mileage is a countdown mile meter The service mile display can be disabled or can be set to count down from 500 7500 miles If the service mileage is enabled and it gets to 0 miles it will display 5S du each time the key is turned on If the push button switch is pressed and held while S XXXX is displayed the service miles will be reset to your preset e Press and release the switch until S XXXX is displayed then press and hold the switch until is displayed e Release the sw
3. of the bezel and slide the tab that is under the ignition switch out from under the switch cover see photos below of ignition switch cover removed to show detail Now unplug the gauge connections cable where applicable Remove switch and unplug the idiot lights so the bezel can be completely removed for easier installation of the new gauges Remove the clamp s that hold the gauges to the bezel and remove the gauges and grommets gaskets il wA od FA Gauges Grommets removed Picture of tab switch cover removed Bezel removed Install New Gauge Note This step is only for those with out a factory switch or cable drive applications since the switch was mechanical and attached to the speedometer Now is a good time to install the function switch for cable drive applications it can be hard to mount once the gauges are installed Remove the rubber boot insert the switch from the back of the fairing and then tighten the rubber boot on from the front Next you are ready to install the new gauges into the fairing The new speedometer comes supplied with a new gasket and clamp Install the gauge and secure using the supplied clamp and gasket Be sure the alignment tab on the clamp lines up with the notches in the fairing Some fairings may only have one notch line up at least one tab on the clamp with the notch in the fairing this will insure the gauge is centered and aligned correctly r Speedometer 2 MAN 650334 A WI
4. replace the cable nut with the supplied cable nut so your speedometer cable will thread onto the new sender You have to take the cable off at the wheel so the nut can slide down and off the end of the cable and allow the new nut to slide on After the nut has been replaced the speedometer cable can be connected back to the wheel and also to the sender Secure the sender with a zip tie and make sure there is no binding in the cable and that the cable has engaged fully into the sender Switch wiring Using either the factory trip reset switch or the supplied push button switch connect one wire from the switch to the MCL 30K SPD green wire The other wire from the switch should be spliced into the MCL 30K SPD white red wire The white red wire may be shared with the function switch and the SEN 1017 or stock speed sensor If additional MCL 3K or MCL 30K TCH gauges are being installed the green wires on all of the gauges can be connected together to share the function switch Night dimming The BLUE wire in the MCL 30K SPD harness controls the dimming circuit When this wire receives 12 volts the gauge will dim to 50 intensity This wire can be connected to a toggle switch or to a Dakota Digital MCL 30K TCH the tachometer has a sensor that activates the dimming feature when ambient light is low 3 MAN 650334 A FUNCTION SWITCH The push button function switch mounted beside the speedometer allows access to all of the mileage and performance info
5. RING Switch Input active high 12V 44 2V GREEN wire Momentary push button switch KEY ON POWER Dim Input active high 12V t41 2V BLUE wire Optional toggl Ptos KEY ON POWER 2003 and older MCL 30K SPD Stock harness color Function WHITE RED see VSS speed sensor power out if required WHITE BLACK BROWN VIOLET security system indicator GRAY see VSS speed signal input RED ORANGE WHITE 12 volt power with key on BLACK BLACK ground for gauge PINK BLACK YELLOW engine indicator WHITE WHITE GREEN output speed signal First locate your speedometer connectors in the factory wiring harness that were unplugged from the original speed gauge The wires needed for the Dakota Digital speedometer should all be found here The factory connector can be cut off or the new wires can be spliced into the harness Not all wires may be present on all years or models VSS wiring For cable driven speedometers you will also need to wire in a speed sensor If you have provisions for a transmission mounted sender use Dakota Digital SEN 1017 If not use Dakota Digital SEN 1011 a cable driven speed sensor The following table shows the wiring for each sensor type MCL 30K SPD SEN 1011 SEN 1017 Stock VSS Splice into Black Black Black Black Gray White Green White White Red not used Red Red If you are using the cable driven adaptor you will also need to pull the soeedometer cable from the front wheel and
6. ator wire has about 12 volts when the it should be off and about 0 volts when the indicator should be on MAN 650334 A Speed sensor voltage checks All checks should be made with the sensor connected to the gauge and the key on Checks should be done with a voltmeter and not a test light Checks for the 3 wire sensor should be made between each individual wire and ground 3 wire sensor Red wire should have 9 11 volts dc slightly less than battery voltage sometimes 5V if supplied by factory harness Black wire should show ground 0 volts dc at all times White wire should vary between 0 and 5 volts dc as the gear teeth or a steel object passes by the sensor Aluminum and Stainless Steel will not work with a Hall effect sensor This can be checked with the sensor mounted and spinning the rear tire slowly or by removing the sensor and moving a steel object pass the face of the sensor 2 wire sensor Measure the voltage between the two sensor wires With the wheel spinning the voltage should be about 1 10 volts ac make sure the meter is set to AC volts and not DC volts for this check WIRING COLOR CODE FOR SPEEDOMETER Color on GAUGE Stock harness color Function WHITE RED see VSS section speed sensor power out if required WHITE BLACK BROWN VIOLET security system indicator GREEN see SWITCH section switch input BLUE none night dimming GRAY see VSS section speed signal input WHITE WHITE GREEN output speed signal PINK BLACK YELLOW eng
7. e switch The speedometer will show Press and release the switch so that 5SPd is displayed Press and hold the switch for about 3 seconds until is displayed Release the switch The MPH display will show SEt and the odometer display will show Auto Press and release the switch to move through the different menus press and hold the switch to select a menu option Note The speedometer calibration and gear programming are the only functions that require you to hold the switch while starting the bike and this is only if you are going to adjust the calibration since you will have to ride the bike Some ignition systems may disrupt power to other circuits causing the gauge to reset this is why you must hold the switch while starting if you are performing speedometer calibration All other gauge functions and gauges can be set without running the engine SPEED CALIBRATION There are two methods for calibrating the soeedometer Auto Cal and Adjust Either one can be used Auto Cal requires that you have one measured mile marked out km for metric this is the best method to start with if your speedometer needs a lot of correction Adjust requires you to follow another vehicle going at a set speed time your self over a mile to determine your speed or use a hand held GPS with speed indication Auto Auto Cal e Press and release the switch until Auto is displayed then press and hold the switch until is dis
8. e vehicle s systems and does not cover removal or reinstallation of the product This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect or accident This Warranty is in lieu of all other expressed warranties or liabilities Any implied warranties including any implied warranty of merchantability shall be limited to the duration of this written warranty Any action for breach of any warranty hereunder including any implied warranty of merchantability must be brought within a period of 24 months from date of original purchase No person or representative is authorized to assume for Dakota Digital any liability other than expressed herein in connection with the sale of this product B Q 4510 W 6lst St North Phone 605 332 6513 pera D Z ze jm Sioux Falls SD 57107 Fax 605 339 4106 www dakotadigital com V dakotasupport dakotadigital com Copyright 2011 Dakota Digital Inc 7 MAN 650334 A
9. eed sensor Gauge must be recalibrated see instructions PLEASE SET SPEED Speedometer not calibrated Gauge must be calibrated to your vehicle see instructions Speed reading is erratic or Speed sensor wire is loose or broken jumps around Cable is loose or broken Poor ground connection Ignition Interference Check all wire connections and inspect wire for breaks Check cable between sensor and transmission Check ground connection on speedometer and sensor Check for tachometer wires routed with VSS signal wires Check for VSS signal wires routed near ignition coils Check for poor ignition system ground Use suppression spark plug wires Speed reading is incorrect _ Gauge is not calibrated correctly Gauge must be calibrated see instructions Gauge will not dim Blue wire 2 pin harness is not connected Check wiring connections Blue wire should have 12 volts correctly when tachometer is dim Gauge remains dim at all Blue wire 2 wire harness is getting power all Check wiring connections Blue wire should have 0 volts times all of the time when tachometer is bright Security indicator does not work Loose or incorrect connection to indicator wire Check that the appropriate indicator wire has about 0 volts when the it should be off and about 12 volts when the indicator should be on Engine indicator does not work Loose or incorrect connection to indicator wire Check that the appropriate indic
10. elect setup for that particular gauge function speed tach oil psi oiltemp fuel volt 1 Sps EL a A e E aS SPd se e e esi lll Sees 3 3 ECH sga a Jala a 4 4 4 P5 4 4 4 5 5 5 5 Fo t 5 5 6 6 6 sipah ae Be lt RUL ibs Te apeta ka es ee ess ll ee ULE 8 eee ecg Sell erg Se lll ep allergies eg FACTORY DEFAULT SETTINGS FOR SETUP MENUS Below is a list of all of the factory gauge settings and what can be adjusted in the setup menus You can calibrate and adjust the speedometer as often as you wish however they should only need to be set once The speedometer calibration will need to be performed to match the gauge for your bike Speedometer Unit MPH Service Meter OFF Performance Menu ON 4 MAN 650334 A SPEEDOMETER SETUP Main Menu Sub Menu Description 5Pd Auto select speed unit and auto calibrate speed AduuSk select speed unit and adjust calibrate speed 5 SEE miles to service setting PErF enable disable performance readings ada one time odometer preset only shown while odometer has less than 100 miles Until the speedometer is calibrated the odometer display will show PLEASE SEE SPEEd This message can be cleared temporarily by pressing and holding the switch To enter the speedometer setup press and hold the switch while turning the key on and starting the engine Once the engine is running release th
11. ine indicator BLACK BLACK ground for gauge RED ORANGE WHITE 12 volt power with key on SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line In addition technical consultation is available to help you work through any questions or problems you may be having installing one of our products Please read through the Troubleshooting Guide There you will find the solution to most problems Should you ever need to send the unit back for repairs please call our technical support line 605 332 6513 to request a Return Merchandise Authorization number Package the product in a good quality box along with plenty of packing material Ship the product by UPS or insured Parcel Post Be sure to include the RMA number on the package and include a complete description of the problem with RMA number your full name and address street address preferred and a telephone number where you can be reached during the day Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase Send no money We will bill you after repair Dakota Digital 24 Month Warranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it under normal use and condition be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE such defect s will be repaired or replaced at Dakota Digital s option This warranty does not cover nor extend to damage to th
12. itch The current setting will be displayed OFF or a mileage from 500 1500 e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed PErF Performance menu setup The performance readings can be turned on or off When they are turned off the odometer will only toggle through the mileage readings e Press and release the switch until PErF is displayed then press and hold the switch until is displayed e Release the switch The current setting will be displayed an or oF F e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed odol Odometer preset The odometer can be preset by the customer within the first 100 miles Once the odometer has more than 100 miles the menu option will no longer be displayed Make sure you have first calibrated the speedometer and correctly selected the units to be either MPH or km h first The odometer will be set in the selected units Once you have preset the miles you cannot change it again WARNING This only allows setting odometer to the nearest mile Do not use tenths For example a mileage of 65432 1 should be set to 1565432 using this method If the tenths digit is used the odometer will read 10 times too high e Press and release the switch until oda is displayed then press and hold the switch until is displayed e The c
13. played e Release the switch The display will switch to un E and light up the current speed unit MPH or km h e Press and hold the switch to keep the current unit or press and release the switch to change the unit e Next the speedometer will display CAL and the message display will show zeroes You should now begin driving the measured mile The message display will count the number of pulses received from the sensor The message display cannot be used to determine when a mile has been driven Once you reach the end of your marked mile press and release the switch again The calibration is now done AdJduSt Adjust e Press and release the switch until AdUu5t is displayed then press and hold the switch until is displayed e Release the switch The display will switch to unit and light up the current speed unit MPH or km h e Press and hold the switch to keep the current unit or press and release the switch to change the unit e Next the system will restart with AdJuSe on the message display The speedometer will show the speed reading Begin driving at a known speed When the switch is pressed the speedometer reading will begin increasing until the switch is released The next time the switch is pressed the reading will begin decreasing until it is released When the speedometer is correct you can release the switch The new calibration will be saved if no adjustments are made for 10 seconds PLEASE NOTE
14. rmation Pressing and releasing the function switch toggles through the different displays Pressing and holding the switch for about 2 seconds will reset the current display The display sequence is as follows SPEED MENU o0g000 odometer mileage A 000 0 trip meter mileage A g 000 0 trip meter mileage B 5 0000 count down to service if programmed ZSIS Speedometer will show km h or MPH if metric PERFORMANCE MENU oo high speed recall 0 60mph time 0 100kph quarter mile time es o0 quarter mile speed The 0 60 and mile timers are zeroed by pressing and holding the switch while that timer is displayed The timer will not restart until the speed reaches zero and you start driving again GAUGE SETUP AND CALIBRATION The function switch discussed above is used to enter setup mode for all of the gauges If you are only installing one or a couple Dakota Digital MCL 3K gauges setup may seem a little strange since they are designed to work as a set The first step in the setup procedure is to select which gauge you are going to adjust Each gauge will either show a number or a label If the gauge is showing a label then that gauge will be selected to enter setup All of the other gauges will exit setup and allow the selected gauge to be changed To get into setup press and hold the function switch while turning the key on Press and release the switch to advance through the menus below when on the desired option press and hold the switch to s
15. urrent miles will be displayed with the left most digit flashing e Press and release the switch to increment the digit Press and hold the switch to move to the next digit to the right e Continue until the right most digit has been set Press and hold the switch and the speed display will show no e Press and hold the switch while no is displayed to go back and continue changing the odometer display Turn the key off to cancel any changes e Press and release the switch to change to speed display to 4 E5 Press and hold the switch while YE5 is displayed to save the current odometer reading Speedometer Troubleshooting guide Problem Possible cause Gauge will not light up Red wire does not have power Black wire is not getting a good ground Solution Connect to a location that has power Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge lights up but speed Gray wire is not connected properly will only show zero Speed sensor not grounded properly Speed sensor is not being turned by transmission Sensor is not sending a speed signal Gauge is not calibrated Check connection from gray wire to speed signal wire Move ground to different location preferable close to the speedometer ground Check cable connection between sensor and transmission Sensor can be tested by spinning the cable with a drill Check for a damaged or malfunctioning sp
Download Pdf Manuals
Related Search