Dacor Oven EORD227 User's Manual
Contents
1. For your safety do not use the oven to cook without the convection filter installed When the filter is not installed the spinning fan blades at the back of the oven are exposed Non stick coatings when heated can be harmful to birds Remove birds to a separate well ventilated room during cooking To prevent damage remove the meat probe from the oven when it is not being used Do not line the oven with aluminum foil or other materials These items can melt or burn up during self cleaning and cause permanent damage to the oven Do not leave metal objects such as aluminum foil the meat probe cookie sheets etc on the bottom of the oven Objects left on the bottom of the oven could damage the bake element In addition the objects themselves could be damaged Do not allow heating elements in the top and bot tom of the oven chamber to become covered up by cookie sheets aluminum foil pots pans etc Covering the heating elements could cause them to over heat damaging the oven On some models the heating elements are behind glass panels Always ensure that the light fixture lens covers are in place when using the oven The lens covers pro tect the light bulbs from breakage caused by high oven temperatures or mechanical shock Customer Service Information If You Need Help e If you have questions or problems with installation con tact your Dacor dealer or the Dacor Customer Service Team When you2. eeeeeeeeeeeeeeneeeeeeeeneeeeeeeeenaeees 3 Reinstalling the Oven DOO rs c ceeeeseeeeeeetteeeeeenees 13 Product Specifications 0 cccccccecceseeeeeeeeeeeeeeeeeeeeeeeees 4 Verifying Proper Operation cccccceeeeeseeeseseeeeeeees 14 Power Supply Requirements cccccceeeeeeeeeseeeeeees 4 Installation Checklist ccccccccccccceeesseeesaeaeaeaeaeaeeeeeenes 15 Product Dimensions cceceeeeeeeeceeeeeeeeeeeteeteeseeaees 4 Before You Begin Important e Installer In the interest of safety and to minimize problems read these installation instructions completely and care fully before you begin the installation process Leave these installation instructions with the customer e Customer Keep these installation instructions for future reference and the local electrical inspector s use Important Safety Instructions DANGER Important Information About Safety Instructions The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur Use common sense and caution when installing maintaining or oper IMPORTANT Do not store or use combustible flam mable or explosive vapors and liquids such as gasoline inside or in the vicinity of this or any other appliance Also keep items that could explode such as aerosol cans away from the oven Do not store flammable or explosive materia
3. immediately after installation of the door 1 Grasp the oven door on opposite sides and hold it at a For double ovens test oven operation for both the upper 15 angle from the front of the oven Slide the hinges and lower ovens into the hinge openings resting the bottom of the hinge arms on the hinge receptacles Continue to hold the 6 Press the BAKE key on the control panel The default bake temperature should appear on the display door at a 15 angle with one hand while pushing in on each of the bottom corners of the door Push until the 7 Press START After approximately three 3 minutes notch on the bottom of each hinge slips over the lower the lower heating element should glow red through the lip of each hinge receptacle glass 2 Lower the door to the fully opened position 8 Press CANCEL SECURE 3 Rotate the two hinge locks toward the oven 9 Press the BROIL key on the control panel The default 4 Slowly and carefully open and close the door completely broil temperature should appear on the display to ensure that it is properly installed 10 Press START After approximately three 3 minutes the upper heating element should glow red On some ovens the element is behind the glass panel on the ceiling of the oven 11 If the oven does not operate properly follow these troubleshooting steps e Verify that power is being supplied to the oven If power is being properly supplied turn off power at the circui
4. bottom of cabinet door 1 2 5 cm min to top of 3 4 1 9 cm drawer face Support Platform 9 5 8 24 4 cm Recommended ane ea Double Wall Oven Cut Out Dimensions 1 25mm min to combustibles Recommended Electrical Location 4 Typical Toe Kick 1 2 5 cm min to combustible floor Single Wall Oven Installed Under Counter dscor 7 Installation Instructions Verify the Package Contents Verify that all the components below have been provided If any item is missing or damaged please contact your dealer immediately Do not install a damaged or incomplete appliance Make sure that you have everything necessary to ensure proper installation before proceeding e Use and care manual e Exhaust grill with 2 mounting screws 2 8 X 3 8 color Mounting screws Wood 6 X Dacor PN 83331 4 for should match exhaust grill Silver Dacor PN 83571 single ovens 6 for double ovens Black Dacor PN 83263 e Standard oven racks single ovens come with 2 double Light Lens Pry Stick ovens come with either 4 or 5 e Dacor Stainless Steel Cleaner stainless steel models GlideRack oven rack 1 only e Broil grill and pan e Meat probe Remove the oven door s Remove the door s to reduce weight and make the Removing the Oven Door s All Models oven easier to lift Except EORS136 WARNING See facing page for removing door from model 5 7 5 EORS136 Do not attempt
5. cabinet cut out using the upper edge of the cavity opening and the bottom of the oven case side as gripping points Be certain to take all necessary safety precautions due to the weight of the appliance Gripping point Gripping point case bottom both sides Mounting Screws Four 4 for single oven 2 Resting the oven on the cabinet mounting platform slide Six 6 for double oven the oven into the recessed area until the rear edge of the oven frame is flush with the cabinet face and the oven is centered within the cut out Ensure that the electrical conduit slides through the opening in the cabinet platform or coils above the oven chassis as the oven is slid into place The cable must be placed into the recessed area located along the rear vertical edge of the oven or coiled above the oven chassis Do not trap the appliance cable between the oven case back and the rear wall 12 cacor Installation Instructions Installing the Exhaust Grill With the oven secured to the cabinet install the exhaust grill by mounting it to the oven with the two 2 provided screws Reinstalling the Oven Doors WARNING Failure to fully rotate the hinge catches will result in a safety hazard and may cause personal injury due to the door falling off its hinges Also damage to the oven and or improper door alignment may occur CAUTION On double ovens install the top door first to reduce the chance
6. 2 2 cm 69 9 cm 23 8 cm MORS130 75 9 cm 72 1 cm 35 7 8 34 3 8 28 5 8 27 5 8 EORS136 94 1 cm 87 3 cm 70 2cm 1 250m EORX227 26 7 8 25 3 8 MORX227 68 3 cm 64 5 cm 49 15 16 49 1 16 EORX230 29 7 8 28 3 8 127 0 cm 124 6 cm MORX230 75 9 cm 72 1 cm X Number of convection ovens see page 3 Width at light covers on sides To top of chassis notch behind control panel Utility Utility Utility Control Cutout Cutout Cutout Panel Width F Height G Depth H Depth J Notch Chassis Notch Depth K Depth L Height M All Models a 5 6 T 1 1 8 24 T 12 7 cm 13 3 cm 15 2 cm 2 54 cm 2 9 cm 61 0 cm 2 5 cm 4 decor Design Specifications Product Dimensions All tolerances 1 16 1 6 mm 0 unless otherwise stated a Top of Top of L Chassis L Chassis B Conduit 60 152 cm Long Control Panel Front Top of Ni Chassis Width at light Chassis Notch UY covers on both sides Tight C Side View 7 ae duit onduit Single Oven 60 152 cm Control Panel rad Front Ten Ny Chassis 4 1 Chassis Notch UY Double Oven 2 5 cm 2 5 cm Side View a 33 8 o 8 6 cm Epicure Millennia Handle is integral Handle Dimensions Installation Specifications Installation Plan ning e Dacor recommends installing the electrical junction box in
7. according to these instructions The installer must connect the ground terminal or lead on the appliance to a grounded metallic perma nent wiring system or grounding conductor Failure to do so may result in an electric shock hazard Do not use an extension cord with this appliance Such use may result in fire electric shock or personal injury Do not install a fuse in the neutral or ground circuit A fuse in the neutral or ground circuit may result in an electric shock hazard The appliance must be connected to the power supply with copper wire only The use of aluminum wire may result in unsatisfactory conditions IMPORTANT Provide slack in the conduit to allow the oven to slide for ward for servicing NOTE The electrical connection leads from the supplied appli ance conduit may be a smaller gage than the standard household wiring of the dedicated supply circuit They are suitable for connection to household wiring under the jurisdiction of the National Electric Code and or the local inspection authority 1 Before proceeding turn off power to the circuit to which the oven will be connected at the circuit breaker or fuse box 2 Position the oven directly in front of the cabinet cut out 3 Feed the appliance conduit into the electrical junction box and attach it using a UL approved strain relief 4 Depending upon local codes utilize one of three meth ods to connect the appliance to the electrical po
8. cacor Tins Geto chan Installation Instructions Renaissance Wall Oven Models EOR MOR Part No 102579 Rev G All specifications are subject to change without notice Dacor assumes no liability for changes to specifications 2007 Dacor all rights reserved Table of Contents Before You Begin sssssnssssnnnunnrnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 1 Installation Specifications cccsssseeeeeesseeeeeeeeseeeeeenees 6 Important Safety Instructions cc ccceseeeeeseesteeeeeeeseeeens 1 Installation Planning ceeseeeeeeecceeceeeeeeeeeeeeeeeeeneneaees 6 Important Information About Safety Instructions 1 installation INStructions ceseeeeneseseeeeeeeeeeeeeeeeneeeeeeens 8 Safety Symbols and Labels l a 1 Verify the Package Contents cccecceceeeeeeseeseteneees 8 General Safety Precautions ccc cceeeeeeeeeeeenteeeeeeeenaes 2 Remove the oven door s 2 e ceceeeeeeeeeeeeseeseeeesaeees 8 Customer Service Information ccccesssecesesseereeeeeeees 3 Electrical CONNECTION cc ecceeeeeeeeeeeeteeeeeteeeneeeeeeeenaeees 9 If You Need Help ccccececceeeseceeeceeceeceeeeeeeeeeeseesnenuaeeees 3 Installing the Oven in the Cabinet c seeeees 12 Appliance Data Plate ceceecececeeeeeeeeeeeeeteeeeeneeaeees 3 Installing the Exhaust Grill 0 0 0 ccceeeeeeteeeeeeeeeeeeees 13 Model Identification 0 0 0
9. call have the model and serial num ber of the appliance ready The model and serial num ber are printed on the appliance data plate Dacor Customer Service Team Phone 800 793 0093 E mail customerservice Dacor com Web site www Dacor com Appliance Data Plate e The appliance data plate contains the model and serial number information and the electrical and gas supply requirements It can be seen through the grill located below the control panel Open the door to expose the grill On double ovens the plate is located behind the top grill View data plate through grate Model Identification EORS227SCH A BCD E MODEL EOR Epicure Renaissance MOR Millennia Renaissance EJ NUMBER OF CONVECTION OVENS S Single D Double NUMBER OF OVENS 1 Single 2 Double By WIDTH 27 27 Inch 30 30 Inch 36 36 Inch TRIM SCH Stainless Steel with Chrome Trim B Black Handle Black Trim BK Black Handle Stainless Trim S Stainless Handle Millennia Style cacor 3 Product Specifications Power Supply Requirements e It is the owner s responsibility to ensure that a licensed Model Dedicated Circuit Total Connected electrician performs the installation of the electrical sup ply for this appliance The electrical installation includ ing minimum supply wire size must comply with the National Electric Code ANSI NFPA 70 latest revision MORS127 and local codes and ordinances EORS130 A co
10. en should be placed for convenient edge of the platform must be flush with the cut out at access Make certain that electrical power meeting the front of the cabinet There are no provisions to level the specifications on page 4 can be provided in the the oven after it has been installed 3 4 1 9 cm thick selected location plywood is recommended Cabinet Dimensions Model Minimum Cabinet Minimum Cut Out Minimum Cut out dled ast VAAN Width P Height R EORS127 MORS127_ J amp 2 68 6 em 25 12 64 8 cm EORS130 27 5 8 70 2 cm gt A mocs130 30 76 2 cm 28 1 2 72 4 cm EORS136 36 91 4 cm 34 12 87 6 cm 27 3 2 70 5 cm EORX227 S MORX227 27 68 6 cm 25 2 64 8 cm EORX230 49 1 8 124 8 cm MORX230 30 76 2 cm 28 1 2 72 4 cm X Number of convection ovens see page 3 Minimum Interior Cabinet Depth 24 61 0 cm 6 dacor Installation Specifications Cabinet Dimensions Recommended Electrical Location 1 2 5 cm min to bottom of cabinet door 3 4 1 9 cm Support Platform 1 2 5 cm min to top of cabinet door Alternate Electrical Location 31 1 4 79 4 cm Recommended Single Wall Oven Cut Out Dimensions on pas 11 2 yi 3 8 cm Typical Counter 36 91 4 cm 3 4 1 9 cm Support Platform Recommended Electrical Location 1 2 5 cm min to
11. ing use and care manual 15 To prevent injury due to the unit from tipping for before operating this appliance Keep packaging materials away from children Plastic sheets and bags can cause suffocation If you receive a damaged product immediately con tact your dealer or builder Do not install or use a damaged appliance Do not install or use the appli ance if the conduit is damaged This oven must be properly installed and grounded by a qualified installer according to these instal lation instructions prior to use The installer must show the customer the location of the circuit break er panel or fuse box so that they know where and how to turn off electric power to the oven Dacor is not responsible for service required to correct a faulty installation The owner is responsible to make sure this appliance is properly installed Do not use the door handle s to lift or move the oven A minimum of two people are required to safely install this appliance To avoid an electric shock hazard do not install this appliance outside or near water Do not install or use this appliance if it has been exposed to water Do not install repair or replace any part of the oven unless specifically recommended in the literature accompanying it A qualified service technician should perform all other service Before performing any type of service or installa tion make sure that the electric power to the oven is turned off at the circu
12. ire in the junction box 4 Connect the red wire from the appliance conduit to the red L2 supply wire in the junction box Incoming power Junction box Wire nut 3 places Conduit to oven Three Wire Connection Installation Instructions Connecting to a Three Wire Electrical System with External Ground Where Local Codes Permit WARNING Do not ground the appliance to a gas supply pipe or hot water pipe If connecting the ground wire to a grounded cold water pipe connect using a separate copper grounding wire No 10 minimum and a clamp with an external grounding screw The grounded cold water pipe must have metal continuity to electrical ground and must not be interrupted by insulating materials Any insulating materials must be jumped with a minimum 4 AWG wire to establish continuity to ground NOTE If the junction box has been properly grounded by a licensed electrician the green ground wire from the appliance conduit may be connected to the junction box using a loop terminal Incoming Power Junction Box Wire Nut 4 Places 4 AWG wire Insulating device minimum Bare metal Insulated Pipe Jumper To connect the green appliance conduit wire to a grounded cold water pipe 1 Separate the wires coming out of the appliance conduit 2 Connect the white wire from the appliance conduit to the white neutral supply wire in the junction box 3 Connect the b
13. it breaker or fuse box Only use the oven for cooking tasks expected of a home appliance as outlined in the literature accom panying it This oven is not intended for commercial use Do not climb on any part of the appliance Do not leave children alone or unattended in the area around the oven Do not allow children to play with the controls pull on the handle or touch other parts of the oven Do not store items of interest to children above the oven Children could be burned or injured while climbing on the appliance Do not tamper with the controls Do not adjust or alter any part of the oven unless specifically instructed to do so in this manual 2 dacor ward secure the oven to the cabinet using the sup plied mounting screws Keep flammable items such as paper cardboard plastic and cloth away from hot surfaces Do not put such items in the oven Do not allow pot holders to touch hot surfaces Do not wear loose or hanging apparel while using the oven Do not allow clothing to come into contact with the interior of the oven and the surrounding areas during and immediately after use Do not use the oven for storage Do not touch the interior surfaces of the oven during use After use make sure these surfaces have had sufficient time to cool before touching them Do not touch the outside surfaces of the oven dur ing the self clean cycle They will be hot Venting from the oven may cause the trim to become hot
14. lack wire from the appliance conduit to the black L1 supply wire in the junction box 4 Connect the red wire from the appliance conduit to the red L2 supply wire in the junction box 5 Connect the green wire from the appliance conduit to a grounded cold water pipe as shown Jumper any insu lating materials as shown above with a length of No 4 copper wire Securely clamp the wire to bare metal at both ends Separate 10 AWG Wire Minimum Clamp wire tightly to pipe Three Wire Connection with External Ground dscor 11 Installation Instructions 3 Locate the mounting holes in the trim on both sides of Installing the Oven In the Cabi net the oven There are four 4 holes two 2 on each side for single oven models and six 6 holes for dou WARNING ble oven models e Failure to properly install the mounting screws may 4 Use a 1 16 drill bit to drill pilot holes in the cabinet result in movement or tipping of the oven during use through all of the trim mounting holes resulting in personal injury 5 Install all of the provided 6 screws through the oven Do not block the oven air exhaust located at the bot trim into the cabinet to secure the oven Do not over tom of the oven Blocking the intake may result in a tighten the screws fire hazard cabinet damage or poor performance The wall oven is heavy Do not attempt to install it in the cabinet with less than two people 1 Lift the wall oven up to the
15. ls in adjacent cabinets or areas ating this or any other appliance e Always contact the Dacor Customer Service Team about problems and conditions that you don t understand See Customer Service Information Safety Symbols and Labels DANGER Immediate hazards that WILL result in severe personal injury or death WARNING Hazards or unsafe practices that COULD result in severe personal injury or death WARNING WARNING NEVER use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating of the appli ance WARNING WARNING NEVER cover any slots holes or passages in the oven bottom or cover an entire rack with materials such as aluminum foil Doing so blocks air flow through the oven and may cause a fire hazard or carbon monox ide poisoning WARNING Do not install this appliance outdoors and or near water for example near a pool WARNING CAUTION Hazards or unsafe practices that COULD result in minor personal injury or property damage READ AND SAVE THESE INSTRUCTIONS When using the BROIL and CONVECTION BROIL set tings the oven door must be completely shut dscor 1 Important Safety Instructions General Safety Precautions To reduce the risk of fire electric shock serious injury or death when using your appliance follow basic safety precau tions including the following WARNING WARNING Read the accompany
16. of damaging the lower door during installation NOTE To re install the oven door on model EORS136 see page 14 1 Grasp the oven door on opposite sides and lift it until the door hinges are aligned with the openings in the oven frame 2 Holding the door at about a 30 angle from the horizon tal slide the hinges into the openings until the bottom hinge arms drop fully into the hinge receptacles AE KK Insert door at 3 Lower the door to the fully opened position Rotate both hinge catches toward the oven Open and close the door slowly and completely to ensure that it is properly installed dacor 13 Installation Instructions Reinstalling the Oven Door Cont Verifying Proper Operation To re install the oven door on model EORS136 1 For stainless steel ovens peel off the protective layer of plastic that covers the stainless steel surfaces WARNING 2 Remove any packaging from inside the oven s To avoid personal injury or damage to the door from 3 Slide the oven racks onto the supports inside the oven it falling off its hinges chamber s according to the use and care manual e Make sure that the notch on the bottom of each hinge 4 Turn on power to the oven at the circuit breaker or fuse rests on top of the lower lip of each hinge receptacle box before attempting to open the oven door 5 Set the clock according to the use and care manual NOTE Rotate the hinge locks toward the front of the range
17. or e 1440 Bridge Gate Drive Diamond Bar CA 91765 e Tel 800 793 0093 e FAX 626 403 3130 e www Dacor com
18. py of this standard may be obtained from MORS130 National Fire Protection Association EORS136 5 3 kW 22 Amp 1 Batterymarch Park EORS227 Quincy Massachusetts 02269 9101 MORS227 240 Vac 60 Hz e The correct voltage frequency and amperage must be EORS230 40 Amp 7 8 kW 33 Amp supplied to the appliance from a dedicated grounded single phase circuit that is protected by a properly sized MORS230 circuit breaker or time delay fuse If a time delay fuse is EORD227 utilized fuse both sides of the line L1 and L2 MORD227 The requi i 240 Vac 60 HZ 10 0 kW 42 Amp quired voltage frequency and amperage ratings EORD230 50 Amp are listed on the appliance data plate see page 3 and in the table for reference MORD239 The above specifications are for reference only See the appliance data plate page 3 for exact specifications 240 Vac 60 Hz 5 0 kW 21 Amp 30 Amp e Preheat times and cavity temperature recovery times will be increased slightly if operating the unit with less than a 240 Vac circuit e This appliance is provided with electrical wiring in a flex ible metal conduit Product Dimensions All tolerances 1 16 1 6 mm 0 unless otherwise stated Model Overall Chassis Overall Chassis Control Panel Number Width A Width B Height C Height D Overlay E EORS127 26 7 8 25 3 8 MORS127 68 3 cm 64 5cm 28 7 16 27 1 2 15 16 EORS130 29 7 8 28 3 8 7
19. t breaker or fuse box an check the electrical con nections e Turn on power and repeat the above heating test e lf the appliance still does not work contact an authorized Dacor service company If you are unable to locate a service representative please contact the Dacor Customer Service Team at 800 793 0093 or visit us on the web at www Dacor com Do not attempt to repair the appliance yourself If you need service be sure to have the model and serial numbers available when you call See page 3 Vv Lower lip of hinge receptacle Notch on bottom of hinge 14 cdacor Installation Instructions Installation Checklist WARNING To ensure proper installation the installer must complete the checklist below to make sure that no part of the in stallation has been overlooked O Is the oven mount on a level platform L Is the oven wired and grounded according to these instructions and in accordance with all applicable elec trical codes See Pages 4 and 9 11 O Is the oven secured into the cabinet with all the mount ing screws four 4 on single oven models six 6 on double ovens See Page 12 O Is are the oven door s properly installed according to these instructions See page 13 L Has proper operation been verified O Has the warranty been activated on line or the warranty card been filled out completely and mailed dacor 15 16 dacor cdacor The Life of the Kitchen Dac
20. the one of the locations shown e Install the junction box in a location that allows the oven WARNING to be removed from the the cut out for service without Observe all governing codes and ordinances during plan being disconnected ning and installation Contact your local building depart e Plan the installation so that all minimum clearances are ment for further information met or exceeded Dimensions shown provide mini mum clearances unless otherwise noted Be certain IMPORTANT that proper clearance is provided for the oven door when it is in the open position according the Product Locate the junction box so that the oven may be easily Dimensions disconnected in the event that it needs to be removed 7 Cabinet cutout dimensions must be used as indicated from the wall completely for service The specified minimum cabinet depth and width must If the oven is not installed level it may deliver poor or be provided The cabinet depth and width must com inconsistent baking results pletely enclose the recessed portion of the oven e A qualified technician must complete the installation of e All contact surfaces between the appliance and the cabi this built in appliance Proper installation is the respon net must be solid and level sibility of the customer e Provide a platform within the cabinet to support the e Carefully check the location where the oven is to be oven It must be installed level and straight The top installed The ov
21. to disengage the hinge catches with the door removed from the oven The hinge springs 1 Open the door to its fully opened position could release causing personal injury 2 Rotate the catch over the retaining arm on both hinges Do not lift or carry oven door by the door handle 3 Lift the oven door to about a 30 angle from the horizon On double ovens remove the bottom door first to tal reduce the chance of damage 4 Pull the door away from the oven while continuing to lift Grab both sides of the door and pull out at a 30 angle to remove Gripping point 8 cdacor Installation Instructions Removing the Oven Door on Model EORS136 1 Open the door to its fully opened position 2 Rotate the catch over the retaining arm on each hinge Catch al ty WW ITV 3 Lift the oven door to about a 15 angle from the vertical position 4 Hold the door with both hands just below the handle and pull it away from the oven while continuing to lift Gripping Gripping point Steps 3 and 4 If the electrical service provided does not meet the Product Specifications see page 4 do not proceed with the installation Call a licensed electrician to cor rectly install the required wiring Failure to disconnect power prior to installation may result in an electrical shock or fire hazard Do not turn on power to the appliance until the oven is properly grounded
22. wer Connect to a four wire electrical system Connect to a three wire electrical system where local codes permit Connect to a three wire electrical system with external ground according to local codes See the instructions on the following pages for detailed directions dacor 9 Installation Instructions Electrical Connection continued Connecting to a Four Wire Electrical System 1 Separate the wires coming out of the appliance conduit 2 Connect the white wire from the appliance conduit to the white neutral supply wire in the junction box 3 Connect the black wire from the appliance conduit to the black L1 supply wire in the junction box 4 Connect the red wire from the appliance conduit to the red L2 supply wire in the junction box 5 Connect the green wire from the appliance conduit to the green ground wire in the junction box Incoming power Junction box Wire nut 4 places Four Wire Connection 10 cacor Connecting to a Three Wire Electrical System Where Local Codes Permit WARNING Do not connect the green appliance conduit wire to the neutral white junction box wire unless local building codes permit 1 Separate the wires coming out of the appliance conduit 2 Connect the green and white wires from the appliance conduit to the white neutral supply wire in the junction box 3 Connect the black wire from the appliance conduit to the black L1 supply w
Download Pdf Manuals
Related Search