D-Link DE-220P User's Manual
Contents
1. the case of a server to provide for network seg mentation Multiple Cards in a PnP System No special attention is needed when installing multiple DE 220P Series cards in a PnP compliant system so long as Plug and Play is enabled In stall the several cards into their expansion slots following the four steps set out in the Single Adapter Installation section above repeating steps 2 and 3 for each card When computer power is switched on the PnP system will auto matically select coordinated conflict free configuration settings for the several cards 3 Plug and Play functionality of the NOS may be toggled between enable and disable by a selection in your setup exe run Installation 2 9 Multiple Cards in a Non PnP System In non PnP systems the procedure for configuring multiple DE 220P Series cards is basically a se quence of separate single adapter procedures make a preliminary installation of each card alone in turn make a setup exe run to configure that card then remove that card and go on to the next CAUTION The following procedure involves operation of the nw 2 10 computer without its chassis housing in place Caution is necessary in order to avoid contact with exposed high voltage parts Accidental contact with exposed internal parts can cause personal injury and can cause damage to the computer equipment Make a preliminary installation of the first DE 220P Series card by completing S2. TCP Pathway Ac cess for DOS SCO UNIX AT amp T UNIX UNIXware Solaris UNIX Overview of PnP Plug and Play technology PnP is defined by Plug and Play ISA Specification v 1 0a A fully functional PnP system includes a PnP compliant operating system a PnP system BIOS and PnP compliant interface cards Windows 95 is the first popular PnP compliant operat ing system Computer mainboards with PnP BIOS s are just reaching the market In the interim PnP technology still provides substan tial benefits For example after installing a non PnP compliant Ethernet adapter card a traditional non PnP compliant card may be called a legacy card into Introduction l b an expansion slot of a PnP compliant mainboard the user can run the ISA Configuration Utility ICU to configure the adapter For some legacy cards the user will need to set DIP switches or jumpers on the card to configure it to the system resources reported available by the ICU With other legacy cards like the D Link DE 220 and DE 220E configuration is accomplished by running the supplied setup program 1 6 Introduction Ins talla tion CAUTION Under ordinary circumstances a DE 220P Series card will not be affected by static charge as may be received through your body during handling of the unit In special circumstances where you may carry an extraordinarily high static charge it is good practice to reduce the charge by touching a ground bef
3. AILURE OR INTERRUPTION OF A D LINK PRODUCT HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY THIS LIMITATION WILL APPLY EVEN IF D LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE IF YOU PURCHASED A D LINK PRODUCT IN THE UNITED STATES SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU Limited Warranty D Link warrants its hardware products to be free from defects in workmanship and materials under normal use and service for the following lengths of time from the date of purchase from D Link or its Authorized Reseller Product Type Warranty Period Network adapters Lifetime Unmanaged and managed hubs Lifetime Repeaters MAUs transceivers media converters One year Concentrators One year Intemetworking products One year Power supply and fans in these devices One year Other hardware products One year Spare parts and spare kits 90 days If a product does not operate as warranted during the applicable warranty period D Lmk shall at its option and expense 1 repair the defective product as part 2 deliver to Customer an equivalent product or part to replace the defective item All products that are replaced will become the property of D Link Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the remainder of the initial warranty period whichever is lon
4. AX 86 10 4991648 J APAN D UNK TOKYO SF 3 9 1 Togoshi Shinagawa ku Tokyo 142 Japan TEL 81 3 5751 2351 FAX 81 3 5751 2352 INDIA D LINK INDIA PVT LTD L 5 Vema Bectronics City Verna Plateau Goa 403722 nda TEL91 834 783093 4 FAX 91 834 783395 TAIWAN D LINK TAIWAN 2F No 233 2 Pao Chiao Rd Hsin Tien Taipei Taiwan R O C TEL 886 2 916 1600 FAX 886 2 914 4299 s Trademarks Copyright C D Link Corporation Contents subject to revision without prior notice D Link and LANsmart are registered trademarks of D Link Corporation All other trademarks belong to their respective owners Copyright Statement No part of this publication may be reproduced in any from or by any means or used to make any derivative such as translation transformation or adaptation without permission from the D Link Corporation D Link Systems Inc as stipulated by the United States Copyright Act of 1 976 FCC CERTIFICATIONS m FCCID DE 220PCAT KA2APC260PI DE 220PCT PT KA2APC260PO The device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Port 15 of the FCC Rules These limits are designed to provide reasona
5. D Link DE 220P Ethernet Network Interface Card for ISA Bus PC PLAY Installation Guide Ethemet Card Model DE 220P senes DE 220PCAT DE 220PCT DE 220PT Installation Guide Rev 05 Jan 1997 6DE 220 P 05 Printed in China WARRANTIES EXCLUSIVE IF THE D LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE THE CUSTOMER S SOLE REMEDY SHALL BE AT D LINK S OPTION REPAIR OR REPLACEMENT THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE D LINK NEITHER ASSUMES NOR AUTHORIZBS ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION w it h INSTALLATION MAINTENANCE OR USE OF D LINK S D LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WILL D LINK BE LIABLE FOR ANY DAMAGES INCLUDING LOSS OF DATA LOSS OF PROFITS COST OF COVER OR OTHER INCIDENTAL CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION MAINTENANCE USE PERFORMANCE F
6. D Link Offices to Contact for Warranty Service To mail your Registration Card or to obtain an RMA number or a warranty service see the following addresses U S A D LINK SYSTEMS INC 5 Musick Irvine CA 92718 USA TEL 1 714 4551688 FAX 1 714 4552521 CANADA D LINK CANADA INC 2180 Dunwin Drive Unit 6 Mississauga Ontario LSL 5M8 Canada TEL 1 905 8280260 FAX 1 905 8285669 U K D LINK EUROPE LTD D Link House 6 Garland Road Stanmore London HA7 IDP U K TEL 44 181 2355555 FAX 44 181 2355500 GERMANY D LINK DEUTSCHLAND GMBH LG Aut Der Krautwede 32 65812 Bad Soden Germany TEL 49 6196 643011 FAX 49 6196 28049 FRANCE D LINK FRANCE Le FLORILEGE 2 Allee de la Fresnerie 78330 Fontenay Le Fleury France TEL 33 1 30238688 FAX 33 1 30238689 SWEDEN D LINK A B World Trade Center P O Box 70396 107 24 Stockholm Sweden TEL 46 08 7006211 FAX 46 08 219640 DENMARK D LINK DENMARK Naveriand 2 OK 2600 Glostrup Copenhagen Denmark TEL 45 43969040 FAX 4543 424347 SINGAPORE D LINK SINGAPORE PTE LTD 77 Science Park Drive 703 03 CINTECH Ill Singapore Science Park Singapore 118256 TEL 65 7746233 FAX 65 7746322 AUSTRALIA D LINK AUSTRALIA PTY LTD Unit 16 390 Eastern Valley Way Roseville NSW 2069 Australia TEL 61 2 4177100 FAX 61 2 4171077 CHINA D LINK BELING RM 108 Building F Hui Yuan international Apartment No 8 Andi Road Chao Yang District Beijing 100101 China TEL 86 10 4934175 4911654 4941969 F
7. ON eere Single Adapter Installation Multiple Adapter Installation Multiple Cards in a PnP System oe Multiple Cards in a Non PnP System Network Cable Connections ou eee The Network Medium is Twisted Pair Cable The Network Medium is Thin Coaxial Cable The Network Medium is Thick Coaxial Cable SPECIFICATIONS beber ete Introduction The D Link DE 220P Series is a new line of Plug and Play Ethernet adapters based on the technology of D Links best selling DE 220 Ethernet adapters Plug and Play PnP technology provides automatic con figuration of newly installed devices without user intervention eliminating much guess work from in stallation of PC upgrades Ease of use is the hallmark of the DE 220P Series After installing a DE 220P Series card configuration is exceedingly simple for both traditional non PnP systems and the newer PnP compliant systems For PnP systems simply install the DE 220P Series card into an expansion slot Configuration by the sys tem software then proceeds automatically If multiple network interface cards are installed the PnP system guarantees that there are no conflicts among them For non PnP systems just install the DE 220P Series adapter into an available expansion slot then run the supplied setup program setup exe Online help an swers your questions and an advanced d
8. ble protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause interference in which case user will be required to correct the interference at his own expense This product generates and used energy of about the same frequency as radio and TV broadcasts Installed incorrectly it it may interfere with reception of radio and TV broadcasts If you suspect this product is causing interference turn your computer on and off while the radio or TV is showing interference If the interference disappears when you u turn the computer off and reappears when you turn the computer on something in the computer is causing interference To reduce interference try these suggestions Change the direction of the radio of TV antenna Move the computer radio or TV For example if the computer is to the right of the TV move it to the left of the TV Or move them farther apart Plug the computer into a different electrical outlet than the radio or TV ensure that all expansions slots on the back or side of the computer are covered Also ensure all metal retaining brackets are tightly attached to the computer TABLE OF CONTENTS INTRODUCTION eene Features i slesodo dete bien eM ees Overview of POP sssssssssse INSTALLATI
9. d pair in the cable makeup and pins 3 and 6 must he a pair Each pin must connect straight through the rahle that is pin 1 through to pin 1 of the opposite connector pin 2 to pin 2 pin 3 to pin 3 and pin 6 to pin 6 pins 4 5 7 8 are not used Installation 2B 2 The cable will have an RJ 45 plug on each end Plug one end into the RJ 45 receptacle of the DE 220P Series adapter and plug the other end into an available port of a lOBase T hub Push each RJ 45 plug into its receptacle until its retainer snaps into place The Network Medium is Thin Coaxial Cable 3a 3b 2 14 Connect a BNC T connector onto the BNC recep tacle of the DE 220P Series card Connect the network feed cable onto either open end of the BNC T connector If the cable continues on to an additional station or stations then connect the continuation cable onto the remaining open end of the BNC T connector If the network cable does not continue to addi tional stations your computer is at the end of the cable then connect a 50 ohm terminator to the remaining open end of the BNC T conector nsta ation BNC Rocha The Network Medium is Thick Coaxial Cab e 1 If there is no Ethernet transciever tap in place for your computer s station on the net work cable then install a transciever not supplied 2 Connect one end of an AUI cable to the Ether net transceiver 3 Connect the other end of the AUI cable to th
10. e AUI connector of the DE 220PCAT Thick coaxial cable N Transceiver ss Sup d Installation 215 DE 220P Series Ethernet Adapter User s Guide Specifications thick coaxial thin coaxial twisted pair YES CE FCC Class B Maximum power 35 Watts consumption IRQ options VO Base Address 240H 260H 280H 2AOH 2COH 2EOH 300H options 320H 340H 360H 380H Boot ROM Size 16K supplied per optional order Boot Base Address C800H CCOOH WOO D400H D800H options DCOOH LED Indicators Power TX Green Rx Link Green Operating Temp 32 F to 131 F 0 C to 55 C Storage Temp 4Fto 176 F 20 C to 80C Humidity 10 to 90 non condensing 2 16 Specifications
11. ger D Link shall not be responsible for any software fiiware information or memory data of Customer contained in stored on or integrated with any products returned to D Link pursuant to any warranty All products with lifetime warranty have a standard five year warranty To qualify for lifetime warranty the enclosed Product Registration Card must be completed and returned to D Link within ninety 90 days of purchase Warranty service may be obtained by contacting a D Link office within the applicable warranty period for a Return Material Authorization RMA number If a Registration Card has not been previously sent proof of purchase such as a copy of the dated purchase invoice must be provided Once an RMA number is issued the defective product must be shipped back to D Link prepaid insured and wrapped in the original or similar shipping package to ensure that it will not be damaged during shipment When returning the defective product to D Link for service the RMA number must be marked on the outside of the shipping package Any product returned without an RMA number shah be rejected and sent back to the Customer and D Link reserves the right to have Customer bear the cost of sending back such products A service charge may or may not be levied to Customer by D Link To find out if a service charge IS levied or not and the charged amount read the RMA that is returned to Customer or ask the D Link office when an RMA is requested
12. iagostic DE 220P _ Series Ethemet Adapter Users Guide__ program is supplied for testing adapter functions and communication with other computers on the network Features DE 220P Series Ethernet adapters comply with IEEE 802 3 Ethernet standards and use VLSI components for enhanced reliability The following features dis tinguish D Link DE 220P Series Ethernet adapters Easy Installation DE 220P Series Ethernet adapters have no physical jumpers or DIP switches Thus it is never necessary to remove a DE 220P Series card in order to reconfigure When installed in a PnP compliant system configuration is handled entirely by system software with no user intervention In non PnP systems configuration is accomplished by running the supplied setup program Support for 8 bit and 16 bit Expansion Slots DE 220P Series Ethernet cards can be installed in 8 bit XT style or 16 bit AT style expansion slots The adapter will automatically detect the type of its expansion slot 1 2 introduction DF220P _Series Ethemet Adapter Users Guide NE 2000 Drivers DE 220P Series Ethernet adapters are fully compatible with network drivers for Novell NE 2000 adapters Diagnostic Program A supplied diagnostic program tests all functions of the DE 220P Series adapter and verifies its communication with another computer on your network LEDs Two LEDs provide network state information 1 PWR T
13. nnectors for convenience during network cable upgrades and for versatility when your equipment is moved between areas with different types of network media Only one network cable may be connected to any adapter in any given installation Installation 2 1 sections following according to your network cable type Network Cable Types DE 220PT Twisted Pairs only DE 220PCT DE 220PCAT Thin Coaxial and Twisted Pair Thick Coaxial Thin Coaxial and Twisted Pair Twisted pair TP cable features RJ 45 connectors and is available with or without EM shield TP cable without EM shield is also known as 10BaseT cable or UTP Unshielded Twisted Pair cable TP cable with EM shield is known as screened twisted pair cable and the EM shield may be either an aluminum sheath or a copper braid enclosing the twisted pair bundle This medium features BNC connectors and is known by a variety of other names including lOBase2 cable BNC cable and RG 58 rable This medium features AUI connectors and is also known as lOBase5 cable It is sometimes called by names such as frozen yellow garden hose due to its bulk weight and stiffness 2 D Installation The Network Medium is Twisted Pair Cab e 1 Ascertain that you have a straight twisted pair cable not more than 100 meters 328 feet in length for thenetwork connection Twisted pair cable RJ 45 jack Pins 1 and 2 must be a pair the connected wires must be a twiste
14. ore handling the adapter Installation of a DE 220P Series Ethernet adapter re quires these three steps Install the adapter into an available expansion slot Connect network cable to the adapter For non PnP systems configure the adapter by running the supplied setup program setup exe For PnP compliant systems this step is fully automated and requires no action This chapter provides detailed procedures for these three steps When these steps are completed you may Installation 2 7 run the diagnostic routines of setup exe program to test the configuration Single Adapter Installation 28 Shut down the computer unplug its power cord and remove the chassis cover Insert the DE 220P Series card into the connector of any open ISA expansion slot You may choose either an 8 bit or 16 bit expansion slot A 16 bit slot will provide better network performance As certain that the card is fully seated in the expansion slot connector Install the bracket screw which secures the card to the computer chassis Replace the cornputer s chassis cover For non PnP systems configure the DE 220P Se ries adapter by running the supplied setup program setup exe For PnP compliant sys tems this step is fully automated and requires no action Installation Multiple Adapter Installation Multiple DE 220P Series cards may be installed in a computer to provide for multiple addresses or in
15. teps 1 through 3 as set out in the Single Adapter Installation sec tion above Restore power to the computer and configure the card by running the supplied setup program setup exe Make a note of the configuration settings that you select to help you select different settings in configuring the remaining cards Shut down the computer and unplug its power cord Remove the configured card and install the next DE 220P Series ard into anypen ex pansion slot Installation DE 220P Seres Ethemef Adapter Users Guide 4 Restore power to the computer and configure the card by running the supplied setup program setup exe Be certain that you select different configuration settings from those that have been selected for another card Make a note of the con figuration settings you select to help you select different settings in configuring remaining cards 5 Repeat Steps 3 and 4 as necessary to configure all DE 220P Series cards which are to be included in the multiple card installation 6 Shut down the computer and unplug its power cord Re install all of the configured cards Re place the computer s chassis cover Network Cable Connections Before connecting a network cable to the DE 220P Series adapter ascertain that your DE 220P model suits your network cable medium as summarized in the following table4 Then refer to one of the three Models DE 220PCT and DE 220PCAT feature multiple network cable co
16. x Indicator Steady green Power indicator shows that the adapter has power computer power is ON and power is supplied to the adapter Flashing green Transmission indicator shows that the computer is transmitting onto the net work This function applies only when the network medium is twisted pair cable gt See Footnote 5 Page 2 12 Introduction 3 2 LNK Rx indicator Steady green Linkage indicator shows that there is a good data linkage to the network Flashing green Reception indicator shows that the computer is receiving from the network This function applies only when the network medium is twistsed pair cable Remote boot option A Remote Boot ROM is available per optional or der The Remote Boot ROM easily snaps into a mount on the DE 220P Series card to provide for remote booting of computers which do not store a boot program Runs a wide variety of networking software DE 220P Series Ethernet adapters can be used with these networking systems D Link LANsmart D Link TCP IP for DOS NDIS driver Novell NetWare 3 x and 4 x ODI driver MS LAN Manager Windows for Workgroups See Footnote 5 Page 2 12 4 Introduction DE220P Series Bhemet Adapter_ _User s Guide Windows 95 Windows NT amp Windows NT Advanced Server SUN PC NFS DEC Pathworks Banyan VINES IBM LAN Server amp PC LAN Support Program Packet Driver 3Com 3 0pen amp 3Com 3 Share FTP PC TCP WIN
Download Pdf Manuals
Related Search