Cub Cadet 2200H Operator's Manual
Contents
1. Detergents can only be applied in the low setting Step1 Slide the detergent tray into one of the slots of your choice Secure the tray to the frame by fastening the screw Step3 Fill a container with Cub Cadet detergent Place the filter end of detergent suction tube into the container Be sure to adjust the filter by turning it to the desired detergent intake For best results see Cleaning Tips on pages 9 amp 10 for specific information on how to clean different surfaces IN Bleach Chlorine products and other corrosive chemicals Liquids containing solvents i e paint Caution Never use thinners gasoline oils Tri sodium phosphate products Ammonia products Acid based products These chemicals will harm the unit and will damage the surface being cleaned Always Use Cub Cadet Detergents for Best Results Step2 The wand must be set in the low pressure position to apply detergents Step4 With the engine running pull trigger to operate unit Liquid detergent is drawn into the unit and mixed with water Apply detergent to work area Do not allow detergent to dry on surface Cub Cadet biodegradable detergents are specially formulated to protect the environment and your pressure washer Special formula won t clog the suction tube filter and will protect the internal parts of the pressure washer for a longer life For Cub Cadet Detergents check your local Cub Cadet dealer If you ne2. un SER 4 A Step3 Connect garden hose to units water inlet Step5 Connect garden hose to the cold water source and turn water on completely always be between the FULL and ADD marks on the dipstick Be sure the machine is level when checking the oil level Refer to the engine s operating manual for seasonal grades Step4 Connect high pressure hose to high pressure outlet Step6 Trigger the gun to eliminate trapped air wait for a steady flow of water to emerge from the spray nozzle OPERATING INSTRUCTIONS continued lt 22 x Step7 Slide the throttle control the fast position Step8 Pull the starter Move the ckoke lever to the CHOKE position only handle If the engine fails to if the engine is cool After starting move the choke start after 3 pulls squeeze to RUN the trigger gun to release pressure and repeat step 8 USING THE ACCESSORIES Spray Wand The spray wand allows you to adjust the cleaning pressure To clean at maximum pressure the wand must be positioned to the high pressure setting To apply detergent the wand must be positioned to the low pressure setting For high pressure turn wand collar in the plus direction For low pressure turn wand collar in the minus direction WARNING TO AVOID SERIOUS INJURY NEVER POINT SPRAY NOZZLE AT YOURSELF OTHER PERSONS OR ANIMALS WORKING WITH DETERGENT
3. Run distilled vinegar through detergent suction tube TROUBLESHOOTING continued Symptom No detergent Garden hose connection leaks Spray wand or Spray extension wand leaks Pump is noisy Water leaks from pump up to 10 drops per minute is permissible Oil Drip Detergent suction tube not properly connected to the machine Solution Check connection Detergent is too thick Dilute detergent for best results use Cub Cadet detergent The filter is closed Open the filter by turning it to the desired detergent intake Filter on detergent suction tube is clogged Run warm water through filter to remove debris Damaged or clogged detergent suction tube Remove obstruction or replace detergent suction tube Spray wand is in high pressure position Turn spray wand tip to low pressure position Discharge nozzle is obstructed Loose fittings Blow out or remove debris with a fine needle Tighten fittings Missing worn rubber washer Spray wand not properly attached Insert new washer Insert the spray wand into the spray wand extension Carefully press in against the spring tension and twist into the locked position Spray wand extension not properly attached Slide the spray wand extension into the gun Turn the wand collar clockwise onto the gun threads until tight Broken o ring or plastic insert Pump is sucking air
4. Loose fittings Contact your local Cub Cadet dealer Check that hoses and fittings are air tight Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Check that all fittings are tight Thermal protection device has been activated Thermal protection device will automatically reset Water seals are damaged or worn Oil seals are damaged or worn Contact your local Cub Cadet dealer Contact your local Cub Cadet dealer f you encounter any additional difficulties not listed please contact your local Cub Cadet dealer 13 14 15 Cub Cadell MANUFACTURER S LIMITED WARRANTY for PRESSURE WASHERS RESIDENTIAL LINE The limited warranty set forth below is given by CUB CADET with respect to new merchandise purchased and used in the United States its possessions and territories CUB CADET warrants this product against defects in material and workmanship for a period of one 1 year for residential users commencing on the date of original purchase and will at its option repair or replace free of charge any part found to be defective in material or workmanship This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operators Manual furnished with the product and has not been subject to misuse abuse neglect accident improper maintenance improper storage or handling fre
5. Cub Cadet I Operator s Manual High Pressure Washer Model 2200H IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY CUB CADET P O BOX 368023 CLEVELAND OHIO 44136 9722 www cubcadet com FORM NO 770 10449 9 00 CONTENTS 3 Safe Operation Practices 3 Assembly Instructions 5 Operating Instructions 6 Using the Accessories 7 Working with Detergents 8 Shut Down and Clean Up 9 Taking Break an 9 Winterizing and Long Term Storage 9 cleaning TDS A A 10 Optional Cleaning Accessories 11 MOUDISSNOOUNG Eee 12 16 MODEL 2200H OVERVIEW Specifications Engine 6 0 HP Briggs Stratton Quantum Water volume 2 0 GPM Operating pressure 2200 PSI Item Description Water inlet Detergent tray w screw Knob Assembly two Oil fill cap High pressure hose Detergent suction tube w filter 7 Handle 8 Accessory rack 9 Trigger gun safety lock 10 Trigger gun 11 Pull start 12 Gas tank 13 Throttle 14 Choke 15 Wand w adjustable spray nozzle 16 High pressure outlet not pict
6. TING Symptom Engine will not start For additional engine problems refer to the engine owners manual Unit does not reach high pressure Output pressure varies high and low No gasoline Solution Fill gas tank Low oil level Add oil Choke is not in correct position Slide choke lever to CHOKE position Engine throttle is not in correct position Position the throttle to FAST Pressure built up in the high pressure washer Diameter of garden hose is too small Squeeze the trigger to release the pressure Replace with a 3 4 inch garden hose Water supply is restricted Check garden hose for kinks leaks and blockage Not enough inlet water supply Open water source full force Water inlet filter is clogged Remove filter and rinse out in warm water Spray wand is in low pressure position Not enough inlet water supply Turn spray wand tip to high pressure position Turn water on full force Check garden hose for kinks leaks or blockage Pump is sucking air Check that hoses and fittings are air tight Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Water inlet filter is clogged Remove filter and rinse out in warm water Discharge nozzle is obstructed Blow out or remove debris with a fine needle Calcified gun hose or spray wand 12
7. ed help locating a dealer in your area contact the Customer Dealer Referral Line by calling 1 877 835 7841 One gallon container of the following Cub Cadet detergents are available e Vehicle Wash Part No KR 9103501 e Deck Wash Part No KR 9103502 e Degreaser Part No KR 9103503 e All Purpose Part No KR 9103504 Cleaner SHUTTING DOWN amp CLEAN UP Step1 Remove Step2 Step3 Step4 detergent suction tube Turn off the engine Turn off the water Press trigger to from container and source release water insert into one gallon pressure of fresh water Siphon water at low pressure for one minute Step5 Disconnect the Step6 Disconnect the high pressure hose from the high garden hose from the pressure outlet and engage the gun safety lock water inlet on the unit TAKING A BREAK five minutes or more Step1 Turn off the engine Step2 Press trigger to Step3 Engage gun safety release water pressure lock WINTERIZING AND LONG TERM STORAGE 1 Disconnect all water connections 5 Store the machine and accessories 2 Start the machine for a few seconds a room which does not reach freezing until the water which had remained in temperatures The machine should not the pump exits Turn off immediately be placed near an open flame i e furnace hot water heater etc Caution Failure to follow the above directions will result in damage to the pump assembly and accessories 3 Drain the gas and oil from t
8. ezing use of improper chemicals alterations vandalism theft fire water or damage because of other peril or natural disaster Damage resulting from the installation or use of any accessory or attachment not approved by Cub Cadet for use with the product s covered by this manual will void your warranty as to any resulting damages The following parts and accessories are subject to separate terms as follows Limited Warranty 90 day free replacement for defects in materials and or workmanship on hoses hose reels spray wands brushes nozzles and or similar approved accessories HOW TO OBTAIN SERVICE Warranty service is available WITH_PROOF OF PURCHASE THROUGH YOUR LOCAL AUTHORIZED CUB CADET or CUB CADET COMMERCIAL DEALER To locate the dealer in your area please check for a listing in the Yellow Pages or contact CUB CADET by calling 877 835 7841 or writing to PO BOX 368023 Cleveland Ohio 44136 9723 This limited warranty does not provide coverage in the following cases a Routine maintenance items such as lubricants filters tune ups or adjustments b Equipment setup normal wear parts or components c CUB CADET does not extend any warranty for products sold or exported outside of the United States its possessions and territories No implied warranty including any implied warranty of merchantability or fitness for a particular purpose applies after the applicable period of express written warranty above No other express warra
9. he engine 4 Do not allow high pressure hose to become kinked CLEANING TIPS Deck Cleaning with or without detergent Pre rinse deck and surrounding area with fresh water If using Cub Cadet Deck Wash place detergent suction tube directly into cleaning solution and apply to surface at low pressure For best results limit your work area to smaller sections of approximately 25 square feet Allow Cub Cadet Deck Wash to remain on surface 1 3 minutes Do not allow detergent to dry on surface Rinse at high pressure in a long sweeping motion keeping the spray nozzle approximately 3 6 inches from the cleaning surface Always clean from top to bottom and from left to right When moving on to a new section of the cleaning surface be sure to overlap the previous section to eliminate stop marks and ensure a more even cleaning result Caution Do not use rotating nozzle spray wand on wood surface as it may cause damage House Siding with or without detergent Pre rinse cleaning surface with fresh water If using Cub Cadet All Purpose Cleaner place detergent suction tube directly into cleaning solution and apply to surface at low pressure for best results limit your work area to sections of approximately 6 feet and always apply detergent from bottom to top Allow Cub Cadet All Purpose Cleaner to remain on surface 1 3 minutes Do not allow detergent to dry on surface if surface appears to be drying simply wet down surface wi
10. her questions regarding the use of recommended cleaning detergent please call your Cub Cadet dealer The machine has hot surfaces which can cause burns Operate the unit in a safe environment and away from children e Do not allow the high pressure hose to come into contact with the muffler guard e Do not leave the machine unattended running e Learn how to stop the machine and release pressure quickly Be thoroughly familiar with the controls e Stay alert watch what you are doing e Do not operate the product when fatigued or under the influence of alcohol or drugs Do not stand on unstable surfaces Stand with both feet balanced at all times The Gun Safety Lock PREVENTS the trigger from accidentally being engaged This safety feature DOES NOT lock the trigger in the on position Water Supply Cold Water Only e Water hose must be at least 3 4 inch in diameter Flow rate of water supply must not fall below 2 5 GPM gallons per minute e Flow rate can be determined by running the water for one minute into an empty 5 gallon container e The water supply temperature must not exceed 104 40 e Never use the pressure washer to draw in water contaminated with solvents e g paint thinners gasoline oil etc e Always prevent debris from being drawn into the unit by using a clean water source We strongly recommend that this high pressure washer not be left running for per
11. iods of 5 minutes or longer without the trigger gun being engaged This high pressure washer is equipped with thermal protection to extend the life of your pressure washer The thermal protector will automatically activate at a predetermined temperature ejecting hot water before resetting This ensures that the pump does not become damaged N Caution e Follow the maintenance instructions specified in the manual e This machine has been designed for use with cleaning detergent supplied or recommended by the manufacturer The use of other cleaning detergents may affect the operation of the machine and void the warranty ASSEMBLY INSTRUCTIONS Step1 Slide the handle through the accessory rack Step2 Align the holes of the accessory Step3 Insert the handle into the frame rack to the handle and fasten the four Align holes insert bolt and tighten with screws knob Step4 Insert the spray wand into the gun Push in and turn clockwise to lock spray wand in place Turn the wand collar clockwise onto the spray wand threads until tight Step5 Attach high pressure hose to trigger gun OPERATING INSTRUCTIONS Step1 Fill gas tank with unleaded gasoline Do not use leaded gasoline Important Do not run the engine with a high or low oil level as this can cause engine damage If you have further questions regarding the engine please refer to the engine s operating manual included with the unit
12. nty or guaranty whether written or oral except as mentioned above given by any person or entity including the dealer with respect to any product shall bind CUB CADET During the period of the Warranty the exclusive remedy is repair or replacement of the product as set forth above Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you The provisions as set forth in this Warranty provide the sole and exclusive remedy arising for the sale CUB CADET shall not be liable for incidental or consequential loss or damages including without limitation to any claim for loss of profits loss of savings or revenue loss of the use of the equipment or any associated equipment facilities or service downtime the claims or costs of third parties including customers and injury to property and further including expenses incurred for substitute or replacement property care services for transportation or for related expenses or for rental expenses to temporarily replace a warranted product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion may not apply to you In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold Alteration of the safety features of the product shall void this warranty You assume the risk and liability for loss damage or injury to you and your propert
13. ove stubborn dirt Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 6 8 inches from the cleaning surface distance should increase when rinsing pin striping or other sensitive surfaces Always clean from top to bottom and from left to right For best results wipe surface dry with a chamois or soft dry cloth Caution Do not use rotating nozzle spray wand on vehicles as it may cause damage CLEANING TIPS continued Barbecue Grills Outdoor Power Equipment amp Gardening Tools with or without detergent Pre rinse cleaning surface with fresh water If using Cub Cadet All Purpose Cleaner or Degreaser place detergent suction tube directly into cleaning solution and apply detergent at low pressure Allow Cub Cadet detergent to remain on surface 1 3 minutes Do not allow detergent to dry on surface Rinse at high pressure keeping the spray nozzle approximately 3 6 inches from the cleaning surface For removing extremely stubborn dirt it may be necessary to move the spray nozzle even closer to the surface for greater dirt cutting action To remove caked on mud from garbage cans lawn mower blades wheel barrels or other non sensitive metal surfaces you may want to use the Cub Cadet Rotating Nozzle Spray Wand Caution Do not use rotating nozzle spray wand on cloth plastic or other sensitive surfaces as it may cause damage Patio amp Lawn Furniture with or without detergent Pre rin
14. se furniture and surrounding area with fresh water If using Cub Cadet All Purpose Cleaner place detergent suction tube directly into cleaning solution and apply to surface at low pressure Allow Cub Cadet All Purpose Cleaner to remain on surface 1 3 minutes Do not allow detergent to dry on surface If needed use special Wash Brush Attachment to remove stubborn dirt Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3 6 inches from the cleaning surface For best results clean from top to bottom and from left to right Caution Do not use rotating nozzle spray wand on patio or lawn furniture as it may cause damage Recommendations e Before cleaning any surface an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results If painted surfaces are pealing or chipping use extreme caution as pressure washer may remove the loose paint from the surface OPTIONAL CLEANING ACCESSORIES To further enhance your cleaning capabilities optional cleaning accessories are available from your local Cub Cadet dealer e Rotating Wash Brush Part No e Wash Brush Part No Rotating Spray Wand Part No e Extension Hose 25 Part No e Plastic Hose Reel Part No KR 9103105 KR 9103106 KR 9103301 KR 9103006 KR 9103053 If you need help locating a dealer in your area contact the Customer Dealer Referral Line by calling 11 1 877 835 7841 TROUBLESHOO
15. th fresh water If needed use special Wash Brush Attachment to remove stubborn dirt Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 6 inches from the cleaning surface Caution Do not use rotating nozzle spray wand on siding as it may cause damage 10 Cement Patios Brick and Stone with or without detergent Pre rinse cleaning surface with fresh water If using Cub Cadet All Purpose Cleaner place detergent suction tube directly into cleaning solution and apply to surface at low pressure For best results limit your work area to smaller sections of approximately 25 square feet Allow Cub Cadet All Purpose Cleaner to remain on surface 1 3 minutes Do not allow detergent to dry on surface Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3 6 inches from the cleaning surface Always clean from top to bottom and from left to right For removing extremely stubborn stains use the Cub Cadet Rotating Nozzle Spray Wand Cars Boats amp Motorcycles with or without detergent Pre rinse vehicle with fresh water If using Cub Cadet Vehicle Wash place detergent suction tube directly into cleaning solution and apply to surface at low pressure For best results clean one side of vehicle at a time and always apply detergent from bottom to top do not allow detergent to dry on surface If needed use special Wash Brush Attachment to rem
16. ured GQ SAFE OPERATION PRACTICES NEVER Never point nozzle at people or animals Never drink alcohol or use drugs while operating this equipment Never spray electrical connections electrical outlets or fixtures Never add fuel with the engine running or operate where fuel has been spilled Never touch hot surfaces or allow accessories to contact hot surfaces Never operate in an enclosed space exhaust fumes are dangerous Never operate near utilities with open flames Never operate without the water turned on and never use hot water SAFE OPERATION PRACTICES Read First N Safety Warnings When using this product basic precautions should always be followed Read all the instructions before using the product e FIRE HAZARD Do not add fuel with the engine running Do not operate if fuel has been spilled Instead move the machine to a different location and avoid creating sparks e Operate and fuel machine in a well ventilated area free of devices featuring an open pilot or flame such as boilers water heaters etc e High pressure jets can be dangerous if subject to misuse The jet must not be directed at persons animals electrical devices or the machine itself Wear safety goggles e Do not use acids solvents or any other flammable material in this product These products can cause physical injuries to the operator and irreversible damage to the machine lf you have furt
17. y and or to others and their property arising out of use or misuse or inability to use this product This limited warranty shall not extend to anyone other than the original purchaser or original lessee or the person for whom it was purchased as a gift HOW STATE LAW RELATES to this WARRANTY This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state
Download Pdf Manuals
Related Search