Computer Tech Link 7dln User's Manual
Contents
1. FACTORY PRESET TIMINGS Mode CI HFreq KHz V Freg Hz Remark VGA 480 640 X 480 31 5 60 Non interlaced VESA VGA 75 640 X 480 37 5 75 Non interlaced VGA 400 720X 400 31 5 70 Non interlaced VESA 46K 800 X 600 46 9 75 Non interlaced VESA SVGA 85 800 X 600 53 7 85 Non interlaced VESA 60K 1024 X 768 60 0 75 Non interlaced VESA 1024 85 1024 X 768 68 7 85 Non interlaced VESA 1280 60 1280 X 1024 64 0 60 Non interlaced The above timings are adjusted on the best display image condition English 10 Picture is blurred Adjust Contrast and Brightness 4 Operate Degauss once Edges of available area on the screen are not straight Adjust Geometry Control Pincushion Trapezoid English 112. from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the monitor c If the monitor has been exposed to rain or water d If the monitor does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore normal operation e If the monitor has been dropped or the cabinet has been damaged f When the monitor exhibits a distinct change in performance this indicates a need for service D 17 When replacement parts are 26 required be sure the service af technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 18 Upon completion of any service or repairs to this monitor ask the service technician to perform routine safety checks to determine that the monitor is safe to operate FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provi
3. GUIDE COLOR MONITOR Model No 7dln S N 9978628208 IMPORTANT SAFEGUARDS 1 Read all of these instructions 2 Save these instructions for later use 3 Unplug this monitor from the wall outlet before cleaning Do not use liquid cleaners or aerosol EN cleaners Use a damp cloth for i cleaning 4 Do not use attachments not recommended by the monitor manufacturer as they may cause hazards 5 Do not use this monitor near water e g near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool etc 6 Do not place this monitor on an y unstable cart stand or table The 22 monitor may fall causing serious W injury to a child or adult and serious damage to the appliance 7 Slots and openings in the cabinet and the back or bottom are 97 provided for ventilation to ensure C A reliable operation of the monitor and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the monitor on a bed sofa rug or other similar surface This monitor should never be placed near or over a radiator or heat register This monitor should not be placed in a built in installation such as a bookcase unless proper ventilation is provided 8 This monitor should be operated only from the type of power source NE indicated on the marking label If you are not sure of the power supplied to your home consu
4. L FUNCTION ch H POSITION Adjust the position of the display horizontally left or right UTILITY Adjust the position of the display SELECT low SI Va POSITION vertically up or down 5 NO YES H SIZE the display width horizontal S DEGAUSS x C V SIZE Adjust the display height vertical size E V LINEARITY Adjust the vertical linearity H LINEARITY Adjust the horizontal linearity Adjust the left and right margins for more convex or more concave margins L PINCUSHION Adjust the trapezoid of the screen by TRAPEZOID moving the lines inward or outward e When you choose the icon on the OSD window you can exit the OSD screen Adjust the side balance when the sides of PIN BALANCE the screen are bowed towards left or right screen is leaning left or right Adjust the pin corner top when the top TARIN CORNER sides of the screen are bowed Adjust the pin corner bottom when the POPIN CORNER bottom sides of the screen are bowed ES 2 Z PARALLELOGRAM Adjust the parallelogram when the English 6 English 7 ICON CONTROL FUNCTION ICON CONTROL FUNCTION D Adjust the side pin corner balance top T PIN BALANCE when the top sides of the screen are bowed towards left or right Display horizontal amp vertical frequency Adjust the side pin corner balance bottom B PIN BALANCE when the bott
5. de reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or TV technician for help CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CANADIAN NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations AVIS CANADIEN Cet appareil num rique de la Class B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada The power cord is used as a main disconnect device Disconnect the power cord before servicing The outlet m
6. etry and screen color The monitor supports a safe working environment in strict compliance with the MPR II standard for low emissions TCO Optional The monitor complies with the VESA Display Data Channel DDC specification for Plug amp Play compatibility Advanced microcircuitry makes set up and configuration fast and effortless The monitor features Advanced Color Controls for fine tuning to meet your own personal tastes or application requirements Use the on screen controls to adjust the color temperature RGB gain value for the best possible screen color and intensity Press the menu button and activate the Self Diagnosis menu to determine whether your monitor is functioning normally not receiving a signal or is receiving a signal that is out of scanning range Activate the higher refresh rates of the monitor to stabilize the screen and eliminate the annoying flicker that contributes to eye strain and headaches The borderless full screen display capability works under all graphic modes and provides a larger viewing area than conventional monitors giving you a better picture with more workspace English 2 SETUP INSTALLING THE TILT SWIVEL STAND 1 2 Ensure that the power to the monitor is off Set the monitor face down with the underside facing you Please be careful so as not to scratch the monitor screen Align the four hooks on the stand with the guide holes of bottom chassis of
7. lt your monitor dealer or local power company 9 This monitor is equipped with a I 3 wire grounding type plug That is a plug having a third m grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the purpose of the grounding type plug 10 Do not allow anything to rest on the power cord Do not locate this monitor where the cord will be abused by people walking on it 11 Follow all warnings and instructions marked on the monitor 12 For added protection for this monitor during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet This will prevent damage to the monitor and or the computer due to lightning and power line surges 13 Do not overload wall outlets and extension cords as this can result in fire or electric shock 14 Never push objects of any kind into this monitor through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the monitor 15 Do not attempt to service this monitor yourself as opening or removing covers may expose you to dangerous voltages or other hazards Refer all servicing to qualified service personnel 16 Unplug this monitor
8. nglish 9 SPECIFICATIONS TROUBLESHOOTING Symptom Check CDT Size 17 inch Diagonal visible image area 16 2 inch Dot Pitch 0 27 mm Synchronization Horizontal 30 70 KHz Vertical 50 160 Hz Plug and Play DDC1 2B CI Power Saving Power Source EPA VESA DPMS Nutek Compliant 100 240 Vac 50 60Hz Free Voltage Power Consumption 95W No picture Check if POWER SWITCH and COMPUTER POWER SWITCH are in the on position Check if the signal cable is correctly connected to the video card y Check if the pins of D sub connector are not bent Check if the computer is in the power saving mode Dimension W x H x D 420 x 453 x 429mm set with stand Weight unpacked lbs Kg 33 9 15 4 Operating Temperature 10 40 C 50 104 F POWER LED is not lit Image is unstable Check if POWER SWITCH is in the on position y Check if the power cord is correctly connected Check if the signal cable is suitable to the video card Image is not centered too small or too large Adjust H amp V Size or H amp V Position to get the proper image Picture bounces or a wave pattern is present in the Keep the devices that may cause electrical interference away from the monitor picture See the FCC information at the front cover of the manual Color looks blotchy Operate Degauss once
9. om sides of the screen are bowed towards left or right Choose different preset color temperatures STATUS and polarity H MOIRE Adjust the horizontal picture moire cancellation V MOIRE Adjust the vertical picture moire cancellation Reset the screen to the Factory Preset Sd RECALL Display Settings ROTATION Adjust the rotation when the screen is U tilted left or right K COLOR TEMP or set your own customized color parameters O RED GAIN Adjust the red gain O GREEN GAIN Adjust the green gain O BLUE GAIN Adjust the blue gain RED BIAS Adjust the red bias O GREEN BIAS Adjust the green bias O BLUE BIAS Adjust the blue bias A LANGUAGE Select language for OSD 5 languages Degaussing keeps the monitor free from A DEGAUSS unwanted magnetism that can result in color impurity English 8 Self Diagnosis When the monitor doesn t display if you press any control key Self Diagnosis screen is displayed Self Diagnosis function checks if the status of the monitor is No Signal or Out of range NO SIGNAL OUT OF RANGE H 30 70 KHz V 50 160Hz PC DISPLAY SETTINGS CORRECT No Signal screen is displayed when the D Sub signal connector is not connected or the status of the monitor is on DPMS mode Out of Range screen is displayed when the applied frequency is under or over normal range E Normal range H 30 70 KHz V 50 160 Hz E
10. the monitor Insert the hooks into the guide holes Slide the tilt swivel stand toward the front of the monitor until the latch locks in position Turn the monitor and the stand upright If you want to remove the tilt swivel stand on the monitor press the latch and pull the tilt swivel stand toward the back of the monitor Lift the stand to separate English 3 CONNECTING THE SIGNAL CABLE AND POWER CORD 1 Turn off the computer and monitor 2 Connect the 15 pin D sub connector to the output port of the video card in your computer 3 Tighten the screws of the connector 4 Plug the power cord into the AC receptacle located on the back of the monitor 5 Plug the other end of the power cord into the AC outlet Si gnal Cable A Power Cord If your power cord is PC to Monitor type plug the other end of the power cord into the AC receptacle in the computer English 4 OPERATION amp ADJ USTMENT Control Panel SELECT ADJUST MENU Launch OSD On Screen Display MENU window Select a sub Menu amp function Move a sub Menu amp function Increase the value of any selected function Adjust the contrast directly when there is no OSD Move a sub Menu amp function Decrease the value of any selected function Adjust the brightness directly when there is no OSD English 5 Key Process OSD Functions ICON CONTRO
11. ust be installed near the monitor and must be easily accessible As an ENERGY STAR Partner Computer Technology Link Inc has determined that this product meets the Energy Star guidelines for energy efficiency CONTENTS INTRODUCTION Introduction A aio 1 This manual explains how to correctly install operate and get the best performance from your monitor Please read this user s Product Featur s aria a liana 2 guide carefully before installing your monitor then keep it near Setup iodio LA Ses RE ban 3 your monitor for quick reference Installing the Tilt Swivel Stand ii 3 A First please check that the contents of the box corresponds with Connecting the Signal Cable and Power Cord 4 the following checklist Operation amp Adjustment iii 5 at Color monitor Specifications Lrf acces ooh tte eee oe 10 Power cord Factory Preset Timings ii 10 Tilt swivel stand Troubleshooting eee 11 User s Guide Warranty Handbook O Registration Card If there is any item missing or damaged please contact your dealer Please keep the box and packing materials so that you may properly store or transport your monitor English 1 PRODUCT FEATURES The convenient and user friendly on screen display allows for easy and accurate adjustments of horizontal and vertical screen size and position geom
Download Pdf Manuals
Related Search