Coleman 2000000142 User's Manual
Contents
1. Connect the elastic loops with S hooks found at the rainfly corners to fabric loops near frame clips Stake out all guylines illus 8 Assemble and insert short Vertical Hinged illus 8 l Door Pole through vertical sleeve and into Completed tent with rainfly bottom pole stop Gently apply pressure to insert top end into top pole stop and zip sleeve closed End guylines Stake down door illus 9 10 Vertical Door Long Door Assemble and insert long Hinged Pole inserts Pole inserts Door Pole through curved door sleeve into sleeve shee and into top pole stop Gently apply and zips in Se fhe pressure to insert bottom end into bottom pole zips a stop and zip sleeve closed illus 9 10 illus 9 Hinged Door Attach light kit See instructions in light kit Pole Stop illus 10 Hinged Door Things You Should Know e Under certain conditions cold weather high humidity etc condensation will form on the inside surfaces of your tent Condensation is caused by water vapor from your breath perspiration or any wet clothing inside your tent It is NOT LEAKAGE through the tent fabric It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent WARNING Fluorescent tube s contain mercury Hg and must be recycled or disposed of according to local Sian a agen ise eeorreea l state or federal laws Call 800 835 3278 or visit period of time wi2. Coleman amp Montana Big Sky Elite 16 Xx7 Instructions apply to Part Number 2000000142 POLE ASSEMBLY PARTS When You Are Ready 2 Main Tent Poles Part No 9278B3681 To Set Up Your Tent Black Select a level campsite clear of rocks branches and other hard or 2 Side Tent Part No 9278B3691 sharp objects Poles Grey Do not set up your tent under trees l For best results in windy conditions 2 Rainfly Poles Part No 9278B3651 position the end of tent into the wind Part No 9278 1101 Hinged Door Pole Part No 9278 1111 Vertical Hinged Door Pole Rainfly Part No 9278 1091 Connect Frame to Tent Locate the pin amp ring systems on either side of the front door and the corresponding pin amp rings on the back side of tent Insert one end of black frame pole onto pin amp Layout amp Positioning of Tent Pole Assembly Layout and position tent with door facing desired direction illus 1 Unzip door ring system on tent stake loop on either side of Stake down tent corners using the tent stake front door illus 3 loops Keep the floor taut illus 2 Go to opposite end of pole diagonally from Assemble all poles by interlocking shock starting point and gradually apply pressure to the corded poles pole forming an arch until you are able to insert Insert the black poles into center pole sleeves the pin into pole end marked with black binding Re
3. peat for second pole The poles should cross forming an Attach tent frame clips to poles X in the middle of tent illus 1 Black poles Front door illus 4 Center section upright illus 2 Tent stake through stake loop illus 3 pin amp ring system located on the front amp rear of tent poles through pole sleeves marked rainfly poles with grey binding at both ends of tent above windows Insert second pin located near center of tent of 4 pin amp ring system into pole end Go to opposite end of pole and gradually apply pressure to the pole forming an arch until you are able to insert the pin into the pole end Attach frame clips illus 5 Grey poles 4 Attach Rainfly Assemble rainfly poles by interlocking shock Raise Ends of Tent A ius Insert grey shorter shock corded Z Frame clips Grommets for illus 6 Assembled tent without rainfly illus 7 Insert rainfly pole through pole corded pole sleeve on underside Insert rainfly pole into pole sleeves illus 10 Geum of rainfl located at the center edges of the Light Aa underside of rainfly illus 7 illus 8 Drape rainfly over tent pole side down The rainfly poles should cover the door and rear window of tent Insert rainfly poles into grommets on tent body illus 6 illus 11 Secure rainfly with attachments Charger located on underside of rainfly
4. thout drying it thoroughly and brushing off caked dirt Do not pack stakes or poles inside your tent Use a separate www coleman com recycle for recycling instructions storage bag or safe disposal locations STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER DURING STORAGE Do not leave your tent set up for weeks at a time be aware that exposure to the ultraviolet rays of the sun can seriously damage material and or cause it to become THE COLEMAN CO INC eee 3600 N Hydraulic e Wichita Kansas 67219 WARNING KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS _ k _ TENT FABRIC This tent meets the flammability requirements of CPAI 84 1 800 835 3278 www coleman com The fabric may burn if left in continuous contact with any flame source The application of any foreign substance to the tent fabric may render MADE IN CHINA the flame resistant properties ineffective PRINTED IN CHINA REV 9 07
Download Pdf Manuals
Related Search