Cobra Electronics microTALK PR 3500 PR 3500-2 DX VP Owner's Manual
Contents
1. is displayed 2 Press the Channel Up or Channel Down button to change the call setting 3 Choose one of the following a Press the Mode Lock button to enter the new setting and proceed to other functions b Press the Enter HieLow button to enter the new setting and return to Standby mode 10 Call Tone Settings You can choose from 10 different call tone settings to transmit a unique call alert Tee To change a call tone setting 1 Press the Mode button until the letter C and the current call tone number 01 through 10 is displayed 2 Press the Channel Up or Channel Down button to hear the other call tone settings 3 Choose one of the following a Press the Mode Lock button to enter the new setting and proceed to other functions b Press the Enter HieLow button to enter the new setting and return to Standby mode 7 A modeloch __ e introduction KOZE Roger Beep Confirmation Tone Roger Beep is an audible tone that your listener will hear when you release the Talk button This alerts the other party that you are finished talking and it is OK for them to speak Teens To turn roger beep on or off 1 Press the Mode button until the Roger Beep icon flashes on the display The current on Fae N or off setting is displayed 2 Press the Channel Up or Channel Down button to select roger beep on or off 3 Choose one of the following a Press the Mode Lock button to enter Channel Buttons the new set2. Icon Seven shared l sca Signal Strength ili Lil an Meter Icon Yx on Roger Beep Icon only eight Hi Low Scan Icon GMRS only Power Icon TERE 38 Privacy Codes gt 4 e Hands Free Operation VOX e VibrAlert Silent Paging e 10 Channel Memory e Signal Strength Meter e Scan Channel privacy code memory Selectable HieLow Power In GMRS e Backlit 7 LCD Display a GE i g Memor e Button Lock Receive 0 Di i di ua Transmit Icon i p e Call Alert 2 Number 10 selectable tones a ii g e Speaker Channel Numbers CTCSS Privacy Microphone 3 Code Numbers Charge Jack Battery Level e Roger Beep Indicator Selectable on off Power Saver Icon Battery Power Saver e Keystroke Tones Selectable on off Memory Icon Maximum range may vary and is based on e Auto Squelch D unobstructed line of sight communication under e Maximum Range ideal conditions Extender e Belt Clip Important FCC Licensing Information This radio operates on General Mobile Radio Service GMRS frequencies which require a Federal Communications Commission FCC license See page 21 for licensing and other related information English Nothing comes close to a Cobra 25 Introduction R Caring for Your microTALK Radio Your microTALK radio will give you years of trouble free service if cared for properly Handle the radio gently Keep the radio away from
3. mode ready to receive transmissions The radio is always in Standby mode except when the Talk Call or Mode Lock buttons are pressed Battery Low Your microTALK radio has a battery level meter that shows when battery power is decreasing A The greater the number of bars visible the stronger the battery level When the battery level is low the last bar and bALo will flash indicating your batteries should be replaced or if using rechargeable batteries recharged Auto Battery Save Your micro TALK radio has a unique circuit designed to extend battery life If there are no transmissions for 10 seconds the radio will automatically switch to Battery Save mode and the Power Saver icon will flash in the display This will not affect the radio s ability to receive incoming transmissions Channel Buttons Channel Number Communicating with Another Person To talk to another person 1 Press and hold the Talk button 2 With the microphone about two inches five cm from your mouth speak in a normal voice 3 Release the Talk button when you are finished talking and listen for a response You cannot receive incoming calls while pressing the Talk button Both radios must be tuned to the same channel privacy code to communicate Channels m To select a channel 1 With the radio on select any of the 22 channels by pressing the Channel Up or Channel Down button Both radios must be tu
4. on that channel privacy code Your radio will remain on that channel privacy code and return to Standby mode b Press the Channel Up or Channel Down button to resume scanning privacy codes If you press the Talk button while scanning but more than 10 seconds after receiving a transmission you will transmit on the channel privacy code on which you last received a transmission This will then return the radio to Standby mode If you do not press any button within 10 seconds your radio will automatically resume scanning privacy codes During privacy code scan while not receiving a transmission you can choose from the following a Press and hold the Talk button to communicate on the channel privacy code that was displayed before you entered mode functions or the channel privacy code on which during scanning you last received a transmission This will return the radio to Standby mode b Press the Mode Lock button to proceed to set memory location scan see page 16 for further details c Press the Enter HieLow button to return to Standby mode on the channel privacy code that was displayed before you entered mode functions or the channel privacy code on which during scanning you last received a transmission Nothing comes close to a Cobra 15 Operation __ e introduction RASS Memory Location Scan Your microTALK radio can automatically scan up to 10 programmed Memory Locations If there are one or few
5. trademarks of Cobra Electronics Corporation USA Cobra Electronics Corporation is a trademark of Cobra Electronics Corporation USA Nothing comes close to a Cobra 23 English
6. 462 5625 2 2 FRS GMRS 462 5875 3 3 FRS GMRS 462 6125 4 4 FRS GMRS 462 6375 5 5 FRS GMRS 462 6625 6 6 FRS GMRS 462 6875 7 7 FRS GMRS 462 7125 8 FRS 467 5625 9 FRS 467 5875 10 FRS 467 6125 11 FRS 467 6375 12 FRS 467 6625 13 FRS 467 6875 14 FRS 467 7125 15 11 GMRS 462 5500 16 8 GMRS 462 5750 17 12 GMRS 462 6000 18 9 GMRS 462 6250 19 13 GMRS 462 6500 20 10 GMRS 462 6750 21 14 GMRS 462 7000 22 15 GMRS 462 7250 E m 3 2 7 gt IMPORTANT NOTICE FCC LICENSE REQUIRED This two way radio operates on GMRS General Mobile Radio Service frequencies which require an FCC Federal Communications Commission license A user must be licensed prior to operating on Channels 1 through 7 on high power or 15 through 22 which comprise the GMRS channels of this radio Serious penalties could result for unlicensed use of GMRS channels in violation of FCC rules Operation of this radio is subject to additional rules specified in 47 C F R Part 95 Licensed users will be issued a Call sign by the FCC which should be used for station identification when operating this radio GMRS users should also cooperate by engaging in permissible transmissions only avoiding channel interference with other GMRS users and being prudent with the length of their transmission time For licensing information and application forms please call the FCC Hotline at 800 418 FORM Request form 159 and form 605 Questions regarding the license application should be directe
7. D including interference that may cause undesired operation FCC Warnings Replacement or substitution of transistors regular diodes or other parts of a unique nature with parts other than those recommended by Cobra may cause a violation of the technical regulations of part 95 of the FCC rules or violation of type acceptance requirements of part 2 of the rules Nothing comes close to a Cobra Bi Product Service Questions oD Customer As Ace Product Service Questions If you have any questions about operation or installing your new Cobra product or if you are missing parts Please call Cobra first DO NOT RETURN THIS PRODUCT TO THE STORE See customer assistance on page A1 For Products Purchased in the U S A If your product should require factory service please call Cobra first before sending your radio This will ensure the fastest turn around time on your repair You may be asked to send your radio to the Cobra factory It will be necessary to furnish the following to have the product serviced and returned 1 For warranty repair include some form of proof of purchase such as a mechanical reproduction or carbon of a sales receipt If you send the original receipt it cannot be returned 2 Send the entire product 3 Enclose a description of what is happening with the radio Include a typed or clearly printed name and address of where the radio is to be returned 4 Pack radio securely to prevent damage in
8. The Cobra line of quality products includes h A Makina Li Id CB Radios microTALK Radios Radar Laser Detectors e f Introduction ME Safety Alert Traffic Warning Systems Handheld GPS Receivers e O ars A GPS ED UE II i Staying in touch with your family and friends is obraMarine adios Power Inverters Accessories i convenient and easy when using your microTALK t 3 IN micro TALK radio Some of the many uses you will discover include i Communicating with others while hiking biking and working keeping track of family and friends at a crowded public event checking with travel companions in another car talking with neighbors arranging meeting spots with others while shopping at the mall Owner s Manual Secure your microTALK radio while on the go Carrying your microTALK radio with you is easy when using the belt clip The belt clip easily attaches to your belt purse or backpack Simply squeeze the clip and place it where you prefer nterfhi Jo CustomePAggistance For Assistance in the U S A In this user s manual you should find all the information you need to operate your microTALK radio If you require further assistance after reading this manual Cobra Electronics offers the following customer assistance services Automated Help Desk English only 24 hours a day 7 days a week 773 889 3087 phone Customer Assistance Operators English and Sp
9. advance to the next mode function Press the Talk button at any point to return the radio to Standby mode modeloch Nothing comes close to a Cobra Operation CTCSS Privacy Codes CTCSS Continuous Tone Coded Squelch System is an advanced tone coding system allowing you to select one of 38 privacy codes to reduce interference from other users on the channel If you are using a privacy code both radios must be tuned to the same channel and privacy code to communicate Each channel will remember the last privacy code you selected Tea ee To select a privacy code 1 After selecting a channel press the Mode Lock button until the small numbers next to the channel number flash on the display 2 Press using the Channel Up or Channel Down button to select a privacy code You can hold the Up or Down button for fast advance 3 When your desired privacy code is displayed ese choose one of the following a Press the Mode Lock button to enter the new setting and proceed to other functions b Press the Enter HieLow button to enter the new setting and return to Standby mode c Do not press any buttons for 15 seconds to enter the new setting and return to Standby mode T 8 English __ e introduction KOZERA Voice Activated Transmit VOX In VOX mode your microTALK radio can be used hands free automatically transmitting when you speak You can set the VOX sensitivity level to fit the volume of
10. anish 8 00 a m to 6 00 p m CT Monday through Friday except holidays 773 889 3087 phone Questions English and Spanish Faxes can be received at 773 622 2269 fax Technical Assistance English only www cobra com on line Frequently Asked Questions English and Spanish productinfo cobra com e mail For Assistance Outside the U S A Contact Your Local Dealer For more information or to order any of our products TWO WAY RADIO MODEL Part No 480 165 P please visit our website p R DX Version B A A Chicago Illinois 60707 USA English www cobra com www cobra com Nothing comes close to a Cobra English Nothing comes close to a Cobra English 2005 Cobra Electronics Corporation Printed in Philippines 6500 West Cortland Street aL LLOG Introduction aL LLOC Introduction Wrist Strap Connector Belt Clip pa Battery Compartment Battery Door Antenna Latch Te a i External Speaker Microphone Charge Jack A On Off Volume Knob Mode Lock Button Backlit LCD Display Enter HieLow Power Button Channel Up Button Channel Down Button Call Button Light Max Range Button Speaker Microphone Ac obra A2 English Features Backlit LCD Display e Two Way Radio With up to an 10 mile Lock Icon 16 km range Call Alerts and O Keystroke Tones Icon e 22 Channels VibrAlert
11. d 15 through 22 on high power the Hi icon will be visible on the display When using those channels on low power and on Channels 8 through 14 the Low icon will be visible on the display Display Illumination To illuminate your display 1 Press and release the Light Max Range button to illuminate the display for 10 seconds Auto Squelch Maximum Range Your microTALK radio is equipped with Auto Squelch which automatically shuts off weak transmissions and unwanted noise due to terrain and conditions This slightly reduces the Maximum Range at which signals can be heard You can turn off auto squelch to allow all signals to be received and extend the maximum range of your radio To briefly turn off auto squelch 1 Press the Light Max Range button for less than five seconds If you hear two beeps you have turned the maximum range extender on see below To turn maximum range extender on 1 Press and hold the Light Max Range button for at least five seconds until you hear two beeps which indicates the maximum range extender is on To turn maximum range extender off 1 Press and release the Light Max Range button or change channels Light Max Range Lock Feature The Lock feature locks the Channel Mode Lock and Enter HieLow Power buttons to prevent accidental operation Tea eee To turn the lock feature on or off 1 Press and hold the Mode Lock button for two seconds man A double beep sound is us
12. d to the FCC at 888 CALL FCC Additional information is available on the FCC s website at www fcc gov Channel 1 through 7 on low power and channels 8 through 14 comprise the FRS Family Radio Service No license is required to operate on the FRS Safety Information for microTALK Radios Your wireless handheld portable transceiver contains a low power transmitter When the talk button is pushed it sends out radio frequency RF signals The device is authorized to operate at a duty factor not to exceed 50 In August 1996 the Federal Communications Commissions FCC adopted RF exposure guidelines with safety levels for handheld wireless devices Important FCC RF Exposure Requirements For body worn operation this radio has been tested and meets the FCC RF exposure guidelines when used with Cobra accessories Supplied or designated for this product Use of other accessories may not ensure compliance with FCC RF exposure guidelines Use only the Supplied antenna Unauthorized antennas modifications or attachments could damage the transmitter and may violate FCC regulations Normal Position Hold the transmitter approximately two inches from your face and speak in a normal voice with the antenna pointed up and away This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received
13. dust Never put the radio in water or in a damp place Avoid exposure to extreme temperatures Remove Belt Clip Batteries 33 To install or replace batteries A 1 Remove belt clip by releasing belt clip Pull Up Latch latch and sliding clip up 2 Pull up on the battery door latch to remove the battery compartment cover 3 Insert four AAA batteries Always use high quality alkaline batteries Position batteries Insert Batteries according to polarity markings 4 Replace battery compartment cover and belt clip Contact your local Cobra dealer or Cobra directly for optional battery pack and wall charger accessories The Basics to Get You Started Your microTALK radio is easy to use To get started simply 1 Rotate the On Off Volume knob to turn on your radio 2 Press the Channel Up or Channel Down button to select a channel Both radios must be tuned to the same channel privacy code to communicate 3 Press and hold the Talk button while Speaking into the microphone 4 When finished talking release the Talk button and listen for a response Nothing comes close to a Cobra L Operation On Off Power ON van amp Battery Low LAU He NN Turning on Your microTALK Radio To turn on your radio 1 Rotate the On Off Volume knob clockwise to turn on your radio and adjust the volume A series of tones will indicate the radio is on Your microTALK radio is now in Standby
14. ed to confirm your lock on or off request When in Lock mode the Lock icon will be displayed ull A a Rog y E ori fl scan modeloch Nothing comes close to a Cobra 5 Operation __ e introduction KOZERA Dual Function Buttons Two of the buttons on the microTALK radio have Dual Functions Mode Lock e Press and release the button to scroll to the next mode function e Press and hold the button for two seconds or more to turn the lock function on or off Enter HieLow Power e Press and release the button to enter settings e Press and hold the button for two seconds or more to toggle between high and low power transmission Speaker Microphone Charge Jack Your microTALK radio can be fitted with an external Speaker Microphone freeing your hands for other tasks This same jack also serves as the connecting point for an optional wall charger adapter me To attach a Speaker microphone ee 1 Open the speaker microphone charge tab on top of your microTALK radio 2 Insert the plug into the speaker microphone charge jack To connect a wall charger adapter 1 Open the speaker microphone charge tab on top of your microTALK radio 2 Insert the wall charger adapter plug into the speaker microphone charge jack Signal Strength Meter Your microTALK radio has a Signal Strength Meter that shows the strength of your incoming and outgoing transmissions The ascending bars next to the
15. eived a transmission see below for further details c Press the Enter HieLow button to return to Standby mode on the channel privacy code that was displayed before you entered mode functions or the channel on which during scanning you last received a transmission Privacy Code Scan Your microTALK radio can automatically scan the Privacy Codes 01 through 38 within one channel Select Channel To scan privacy codes y 1 While in Standby mode press the Channel Up or Channel Down button to choose the channel on which you wish to scan privacy codes 2 Press the Mode Lock button until the mode lock Scan icon and the privacy code numbers flash on the display 3 Press the Channel Up or Channel Down button to begin scanning privacy codes within the channel you selected The Scan icon will continue to be displayed when privacy code scan is on Your radio will continue to scan privacy codes and stop as an incoming transmission is detected Your radio will remain on that channel privacy code for 10 seconds Mode Lock Button __ e introduction KOZERA While setting privacy code scan if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code that was displayed before you entered mode functions During privacy code scan while receiving an incoming transmission you can choose from the following a Press and hold the Talk button to communicate
16. er memory locations programmed in your radio the scan memory locations option will not be available To program at least tvo memory locations see program memory locations on page 10 TEE mess To scan memory locations deio 1 Press the Mode Lock button until the Scan MEA icon Memory icon and the memory location Si number flash on the display SI 2 Press the Channel Up or Channel Down lt A hl button to begin scanning memory locations j gt The Scan icon and the Memory icon will JORS continue to be displayed when memory Channel Buttons location scan is on Your radio will continue eee de to scan memory locations and stop if an 7 A incoming transmission is detected Your radio will remain on that memory location for 10 seconds While setting memory location scan if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed before you entered mode functions During memory location scan while receiving an Incoming transmission you can choose from the following a Press and hold the Talk button to communicate on that memory location Your radio will remain on that memory location and return to Standby mode b Press the Channel Up or Channel Down button to resume scanning memory locations English If you press the Talk button while scanning but more than 10 seconds after receiving a transmission you will transmit on
17. lish o __ e introduction KOERA While setting a memory location if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed before you entered mode functions mep To recall a stored memory channel location 1 Press the Mode Lock button until the Memory icon and the memory location number flash on the display 2 Press the Channel Up or Channel Down button to select a memory location 0 through 9 If a location has been programmed before its associated channel privacy Channel Buttons ce code will be shown on the display y z 3 Press the Talk button to return to Standby mode on the selected memory location A memory location can be reprogrammed at any time it is displayed Press the Enter HieLow button to begin While recalling a stored memory location if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed before you entered mode functions Nothing comes close to a Cobra 14 Kele __ e introduction KOZERA Channel Scan Your microTALK radio can automatically scan channels To scan channels To de program a memory location 1 Press the Mode Lock button until the Memory icon and the memory location Mode Lock Button flash on the display 2 Press the Channel Up or Channel Down button to select the memory l
18. ned to the same channel to communicate Channels 1 through 7 are shared by FRS and GMRS Channels 15 through 22 are GMRS only Channels 8 through 14 are FRS only See page 20 for FRS GMRS frequency allocations and compatibility charts Listening for a Response When you are finished talking 1 Release the Talk button to receive incoming transmissions Your microTALK radio is always in Standby mode while the Talk or Call buttons are not pressed Nothing comes close to a Cobra 3 Operation __ e introduction KOZERA Volume Knob gp i TANT a viv Call Button Enter HieLow Button i Light Max Range 4 English Volume To adjust the volume 1 Rotate the On Off Volume knob Call Button To alert another person that you are calling 1 Press and release the Call button The other person will hear a two second call tone This tone is used only to establish voice communications See page 18 on how to select from 10 available call tone settings Selectable High Low Power Output When in close proximity to another party or during favorable conditions you can switch from High to Low Power to extend battery life This feature applies to GMRS Channels 1 through 7 and 15 through 22 only Channels 8 through 14 operate exclusively on low power To toggle between high and low power 1 Press and hold the Enter HieLow button for two seconds When using Channels 1 through 7 an
19. nsumer purchase such as a duplicated copy of a sales receipt You must pay any initial shipping charges required to ship the product for warranty service but the return charges will be at Cobra s expense if the product is repaired or replaced under warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Exclusions This limited warranty does not apply 1 To any product damaged by accident 2 In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs 3 If the serial number has been altered defaced or removed 4 If the owner of the product resides outside the U S A All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty Cobra shall not be liable for any incidental consequential or other damages including without limitation damages resulting from loss of use or cost of installation Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you For Products Purchased Outside the U S A Please contact your local dealer for warranty information Trademark Acknowledgement Cobra micro TALK Nothing comes close to a Cobra VibrAlert and the snake design are registered
20. ocation 0 through 9 If a location has been programmed before its associated channel privacy code will be shown on the display 3 Press the Enter HieLow button The channel numbers will flash on the display 4 Press the Channel Up or Channel Down button to select Channel 0 5 Choose one of the following a Press the Enter HieLow button to enter the channel privacy code in the selected memory location and return to the beginning of memory location options b Press the Mode Lock button to enter the channel privacy code in the selected memory location and proceed to other functions on the channel privacy code displayed before you entered mode functions While de programming a memory location if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed before you entered mode functions mode lock Channel Buttons i arie The Scan icon will continue to be displayed T 1 Press the Mode Lock button until the Scan icon and the channel numbers flash on the display 2 Press the Channel Up or Channel Down button to begin scanning channels The radio ignores specific privacy codes while scanning channels when scan is on Your radio will continue to scan all channels and stop if an incoming transmission is detected Your radio will remain on that channel for 10 seconds While setting channel scan if you do not
21. press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel or channel privacy code displayed before you entered mode functions During channel scan while receiving an incoming transmission you can choose from the following a Press and hold the Talk button to communicate on that channel Your radio will remain on that channel and return to Standby mode b Press the Channel Up or Channel Down button to resume scanning channels If you press the Talk button while scanning but more than 10 seconds after receiving a transmission you will transmit on the channel on which you last received a transmission This will return the radio to Standby mode If you do not press any button within 10 seconds after receiving a scanned transmission your radio will automatically resume scanning channels Nothing comes close to a Cobra 13 Operation During channel scan while not receiving a transmission you can choose from the following a Press and hold the Talk button to communicate on the channel or channel privacy code that was displayed before you entered mode functions or the channel on which during scanning you last received a transmission This will then return the radio to Standby mode b Press the Mode Lock button to proceed to set privacy code scan on the channel that was either displayed before you entered mode functions or on which during channel scanning you last rec
22. signal strength indicate the strength of the signal The greater the number of bars visible the stronger the signal The fewer number of bars visible the weaker the signal Signal Strength microTALK Range Your microTALK radio has a range of up to 10 miles 16 km Your range will vary depending on terrain and conditions Maximum Range In flat open country your radio will Operate at maximum range Buildings and foliage in the path of the Signal can reduce the range of the radio Dense foliage and hilly terrain will further reduce the range of the radio On FRS channels 8 through 14 your radio automatically switches to low power which will limit the range the radio can communicate Remember you can achieve maximum range by using maximum range extender See page 5 for details Scrolling through Mode Functions By scrolling through the Mode Functions you will be able to select or turn on off preferred features of your microTALK radio When scrolling through the Mode Functions your radio features will be displayed in the following order Tee ma Set Privacy Codes Set VOX On Off Set VOX Sensitivity Level Set Memory Locations Set Channel Scan Set Privacy Code Scan Set Memory Location Scan Set VibrAlert and or Call Alert Set Call Tones Set Roger Beep On Off Set Keystroke Tones On Off Scroll through the mode functions using the Mode Lock button Each press and release of the Mode Lock button will
23. the memory location on which during scanning you last received a transmission This will return the radio to Standby mode If you do not press any button within 10 seconds your radio will automatically resume scanning memory locations During memory location scan while not receiving a transmission you can choose from the following a Press and hold the Talk button to communicate on the channel privacy code that was displayed before you entered mode functions or memory location on which during scanning you last received a transmission This will then return the radio to Standby mode b Press the Mode Lock button to proceed to other functions c Press the Enter HieLow button to return to Standby mode on the channel privacy code that was displayed before you entered mode functions or the memory location on which during scanning you last received a transmission To reduce the number of memory locations being scanned you may de program any unwanted locations See page 12 to de program a memory location Nothing comes close to a Cobra Operation VibrAlert and Call Tones Your micro TALK radio can alert you to incoming signals by sounding an audible call tone by vibrating silently or both Tee sessi To change call settings 1 Press the Mode Lock mode lock button until the Call Setting icon flashes on the display The current setting 01 ica vibrate ring 02 vibrate 7 only or 03 ring only
24. ting and proceed to other eee functions 7 A b Press the Enter HieLow button to enter the new setting and return to Standby mode Roger Beep On Tall Re gi In Keystroke Tones With Keystroke Tones turned on your radio will sound beeps each time you press a button or change a Setting meer To Change keystroke tones 1 Press the Mode Lock button until the moderlock Keystroke Tones icon flashes on the display The current on or off setting is displayed Regge 2 Press the Channel Up or Channel Down EN button to turn keystroke tones on or off 3 Choose one of the following a Press the Mode Lock button to enter the Channel Buttons new setting and return to Standby mode E Db Press the Enter HieLow button to enter the 7 new setting and return to Standby mode II Nothing comes close to a Cobra Operation General Specifications FRS GMRS Frequency Allocation and Compatibility Important Please note that Cobra GMRS models with 15 Channels may designate different channel numbers for the same frequency For example a Cobra 15 Channel GMRS model would need to be tuned to Channel 11 in order to communicate with a 22 Channel GMRS tuned to Channel 15 Please refer to the chart below for channel frequency number compatibility A Channel No for 22 Channel FRS GMRS Models B Channel No for 15 Channel GMRS Models C Type of Radio Service D Frequency in MHz gt oO o B 1 1 FRS GMRS
25. transit If possible use the original packing material 5 Ship prepaid and insured by way of a traceable carrier such as United Parcel Service UPS or Priority Mail to avoid loss in transit to Cobra Factory Service Cobra Electronics Corporation 6500 West Cortland Street Chicago Illinois 60707 U S A 6 If the radio is in warranty upon receipt of your radio it will either be repaired or exchanged depending on the model Please allow approximately three to four weeks before contacting Cobra for status If the radio is out of warranty a letter will automatically be sent informing you of the repair charge or replacement charge If you have any questions please call 773 889 3087 for assistance For Products Purchased Outside the U S A Please contact your local dealer for product service information 2 English Limited One Year Warranty For Products Purchased in the U S A Cobra Electronics Corporation warrants that its Cobra micro TALK radios and the component parts thereof will be free of defects in workmanship and materials for a period of one year from the date of first consumer purchase This warranty may be enforced by the first consumer purchaser provided that the product is utilized within the U S A Cobra will without charge repair or replace at its option defective microTALK radios products or component parts upon delivery to the Cobra Factory Service department accompanied by proof of the date of first co
26. y code combinations These Memory Locations can be selected individually or can be scanned See page 16 for memory location scan NCO ace To program a memory location 1 Press the Mode Lock button until the Memory icon and the memory location flash on the display 2 Press the Channel Up or Channel Down button to select the memory location 0 through 9 If a location has been programmed Channel Buttons before its associated channel privacy code will be shown on the display Press the Enter HieLow button to enter a new memory location or edit an already programmed memory location The channel numbers will flash on the display Press the Channel Up or Channel Down button to select a channel 1 through 22 5 Press the Enter HieLow button The privacy code numbers will flash on the display 6 Press the Channel Up or Channel Down button to select a privacy code 00 to 38 7 Choose one of the following a Press the Enter HieLow button to enter the channel privacy code in the selected memory location and return to the beginning of memory location options Press the Mode Lock button to enter the channel privacy code in the selected memory location and proceed to other functions on the channel privacy code displayed before you entered mode functions Press the Talk button to enter the channel privacy code in the selected memory location and return to Standby mode on the selected memory location Eng
27. your voice and avoid transmissions triggered by background noise Neate To turn VOX mode on or off 1 Press the Mode Lock button until the VOX icon flashes on the display The current on or off setting is displayed 2 Press the Channel Up or Channel Down button to turn VOX on or off 3 Choose one of the following a Press the Mode Lock button to enter the selected on or off setting and proceed to other functions T b Press the Enter HieLow button to enter the selected on or off setting and return to Standby mode Tne To set VOX sensitivity 1 Press the Mode Lock button until the VOX mode lock icon flashes and the current sensitivity level is displayed Channel Buttons ll The current sensitivity level is displayed with letters LE and a Number 01 through 05 with Number 05 being the most sensitive level and Number 01 being the least sensitive level VOX Sensitivity Level Tai ey Channel Buttons he i A 2 Press the Channel Up or Channel Down MLA button to change the setting 3 Choose one of the following a Press the Mode Lock button to enter the selected setting and proceed to other functions b Press the Enter HieLow button to enter the selected setting and return to Standby mode Nothing comes close to a Cobra 9 Operation 10 Memory Locations Your microTALK radio has 10 Memory Locations for storing your most frequently used channels and channel privac
Download Pdf Manuals
Related Search