Clarion DXZ448R User's Manual
Contents
1. 3 Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip INFORMATION FOR USERS CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY DXZAA8R 3 Handling Compact Discs COMPACT Use only compact discs bearing the OSG or Do not use commercially available CD dist mark MuR protection sheets or discs equipped with CERES Do not play heart shaped octagonal or other cause breakdown of the internal mechanism specially shaped compact discs Some CDs recorded in CD R CD RW mode Storage may not be usable Do not expose compact discs to direct sunlight or any heat source Do not expose compact discs to excess humidity or dust Do not expose compact discs to direct heat from heaters Handling Compared to ordinary music CDs CD R and CD RW discs are both easily affected by high temperature and humidity and some of CD R and CD RW discs may not be played Therefore do not leave them for a long time in Cleaning the car To remove fingermarks and dust use a soft New discs may have some roughness around cloth and wipe in a straight line from the the edges If such discs are used the player center of the compact disc to the may not work or the sound may skip Use a circumference ball point pen or the like to remove any Do not use any solvents such as roughness from the edge of the disc commercially available cleaner2. ACAUTION Be sure to lower the volume before switching off the unit power or the ignition key The unit remembers its last volume setting If you switch the power off with the volume up when you switch the power back on the sudden loud volume may hurt your hearing and damage the unit Turning on off the power Note Be careful about using this unit for a long time without running the engine If you drain the car s battery too far you may not be able to start the engine and this can reduce the service life of the battery 1 Press the FNC button 2 The illumination and display on the unit light up The unit automatically remembers its last operation mode and will automatically switch to display that mode 3 Press and hold the FNC button for 1 second or longer to turn off the power for the unit Note System check The first time this unit is turned on after the wire connections are completed it must be checked what equipment is connected When the power is turned on SYSTEM and PUSH PWR appear in the display alternately so press the FNC button The system check starts within the unit When the system check is complete press the FNC button again Selecting a mode 1 Press the FNC button to change the operation mode 2 Each time you press the FNC button the operation mode changes in the following order Radio mode gt DAB mode gt CD mode gt CD changer mode gt DVD changer mode
3. OFF ON AF switching between DAB and RDS enabled OFF AF switching between DAB and RDS disabled 4 Press the T button to return to the previous mode REG Regional programme function When the REG function is ON the optimum regional station can be received When this function is OFF if the regional station area switches as you drive a regional station for that region is received The factory default setting is OFF Notes This function is disabled when a national station such as BBC R2 is being received The REG function ON OFF setting is valid when the AF function is ON Switching the REG function ON Press and hold the AF button for 1 second or longer REG in the display lights and the REG function turns on Switching the REG function OFF Press and hold the AF button for 1 second or longer REG in the display goes off and the REG function turns off Manually tuning a regional station in the same network 1 This function is valid when the AF function is ON and the REG function is OFF Note This function can be used when a regional broadcast of the same network is received 2 Press any one of the DIRECT buttons to call out the regional station 3 If the reception condition of the called out station is bad press the DIRECT button of the same number The unit receives a local station on the same network TA Traffic Announcement In the T
4. Plays the first track Top play Moves the next disc in increasing order Switches reception band v Increases and decreases volume in all modes lt 4 p gt Moves preset channels up and down Moves tracks up and down When pressed and held for 1 second or longer Fast forward fast backward Moves preset channels up and down p ll No function Switches between playback and pause No function MUTE Turns mute on and off TA DISP TA on and off Switches among main display sub display clock CT display PS AS Preset scan When pressed and held for 2 seconds or longer Auto store Scan play Scan play When pressed and held for 1 second or longer Disc scan play Preset scan When pressed and held for 2 seconds or longer Auto store AF function on and off When pressed and held for 1 second or longer REG function on and off Repeat play Repeat play When pressed and held for 1 second or longer Disc repeat play No function PTY standby mode on and off Random play Random play When pressed and held for 1 second or longer Disc random play Switches between TV and VTR Some of the corresponding buttons on the main unit and remote control unit have different functions 2 ZONE button is not available 11 DXZ448R 6 OPERATIONS Basic Operations
5. A M button for 1 second or longer to turn on the MAGNA BASS EXTEND effect M B EX lights in the display 2 Press and hold the A M button for 1 second or longer to turn off the MAGNA BASS EXTEND effect M B EX goes off from the display The factory default setting is off CT Clock Time function The CT function receives CT data sent from a RDS station and displays the time Press the DISP button to switch to the CT display If a CT data is not being received CT appears in the display Note CT data is not transmitted in some countries and by some broadcast stations Also in some areas the CT may not display accurately 1 4 DXZ448R Radio Operations Listening to the radio 1 Press the FNC button and select the radio mode The frequency or PS appears in the display PS Programme service name 2 Press the BND button and select the radio band Each time the button is pressed the radio reception band changes in the following order FM1 gt FM2 FM3 gt AM MW LW gt FM1 3 Press the lt d or P gt button to tune in the desired station Tuning There are 3 types of tuning mode available seek tuning manual tuning and preset tuning Seek tuning There are 2 types of seek tuning DX SEEK and LOCAL SEEK DX SEEK can automatically tune in to receivable broadcast stations LOCAL SEEK can tune in to only broadcast stations with a good reception sensitivity
6. DXZ448R 9 5 REMOTE CONTROL Optional f Receiver for remote control unit If you buy the RCB 164 sold separately you can enjoy the use of the Remote Control function Operating range 30 in all directions ve Signal transmitter Remote control unit FUNC O Coq 2 ZONE gt n p ll d QO a C BAND MUTE DISP REVERSE PS AS AF PTY isum o b C PTY AF Clarion WIRELESS REMOTE CONTROLLER No a Inserting the Batteries 1 Turn the remote control unit over then slide the rear cover in the direction of the arrow 2 Insert the AA SUM 3 IECR 6 1 5V batteries that came with the remote control unit facing in the directions shown in the figure then close the rear cover Notes Using batteries improperly can cause them to explode Take note of the following points When replacing batteries replace both batteries with new ones Do not short circuit disassemble or heat batteries ZA Do not dispose of batteries into fire or flames lt Dispose of spent batteries properly I AA SUM 3 IECR 6 1 5V Batteries Rear cover 1 0 DXZ448R Functions of Remote Control Unit Buttons CD changer TV DVD changer Switches among radio DAB CD CD changer DVD changer and TV FUNC Radio RDS DAB BAND Switches reception band
7. Press and hold the lt d or P gt button for 1 second or longer to tune in a station OG Step tuning Press the lt d or P gt button to manually tune in a station If no operation is performed for more than 7 seconds manual tuning is cancelled and the display returns to the previous mode Recalling a preset station A total of 24 preset positions 6 FM1 6 FM2 6 FM3 6 AM exist to store individual radio stations in memory Pressing the corresponding DIRECT button recalls the stored radio frequency automatically 1 Press the BND button and select the desired band FM or AM MW LW 2 Press the corresponding DIRECT button to recall the stored station Press and hold one of the DIRECT buttons for 2 seconds or longer to store that station into preset memory Manual memory 1 Select the desired station with seek tuning manual tuning or preset tuning 2 Press and hold one of the DIRECT buttons for 2 seconds or longer to store the current station into preset memory Auto store Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially If 6 receivable stations cannot be received a previously stored station remains unoverwritten at the memory position 1 Press the BND button and select the desired band FM or AM MW LW 2 Press and hold the P A button for 2 seconds or longer The stations with good reception are stored automatically to the prese
8. gt TV mode gt Radio mode External equipment not connected with CeNET is not displayed 1 2 DXZ448R Note Be sure to read this chapter referring to the front diagrams of chapter 2 CONTROLS on page 5 unfola Adjusting the volume Turning the ROTARY knob clockwise increases the volume turning it counterclockwise decreases the volume The volume level is from 0 minimum to 33 maximum Switching the display Press the DISP button to select the desired display Each time you press the DISP button the display switches in the following order Main display Main display Once selected the preferred display becomes the display default When a function adjustment such as volume is made the screen will momentarily switch to that function s display then revert back to the preferred display several seconds after the adjustment For information on how to enter a title refer to the subsection Entering titles in section Operations Common to Each Mode When CT data is not received CT appears in the display Setting the Z Enhancer Plus This unit are provided with 4 types of sound tone effects stored in memory Select the one you prefer The factory default setting is Z OFF Each time you press the Z button the tone effect changes in the following order Z OFF 2 B BOOST IMPACT EXCITE gt CUSTOM gt Z OFF B BOOS
9. CD 12 cm For single CD 8 cm Notes Never insert foreign objects into the CD SLOT If the CD is not inserted easily there may be another CD in the mechanism or the unit may require service naii compact e Discs not bearing the niis or Wise mark and CD ROMs cannot be played by this unit Some CDs recorded in CD R CD RW mode may not be usable Loading 8 cm compact discs No adapter is required to play an 8 cm CD Insert the 8 cm CD into the centre of the insertion slot Listening to a CD already inserted Press the FNC button to select the CD mode Play starts automatically If no CD is loaded in the unit NO DISC appears in the display Pausing play 1 Press the p II button to pause play PAUSE appears in the display 2 To resume CD play press the 911 button again DXZ448R 1 9 CD Operations Displaying CD titles This unit can display title data for CD text CDs and user titles input with this unit 1 Press the DISP button to display the title 2 Each time you press and hold the DISP button for 1 second or longer the title display changes in the following order User title disc gt CD text title disc gt Artist name gt CD text title track gt User title disc Note If the CD playing is not a CD text CD or no user title has been input NO TITLE appears in the display Ejecting a CD 1 Press the 4 to eject the CD Take it out from the ejected po
10. PTY select mode 2 Press any one of the DIRECT buttons Alternatively turn the ROTARY knob clockwise or counterclockwise to select the desired PTY Below are the factory default settings stored for the DIRECT buttons Preset PTY item number ENGLISH Contents NEWS News INFO Information POP M Pop Music SPORT Sport CLASSICS Serious Classical Music EASY M Easy Listening Music 3 The PTY select mode is cancelled automati cally 7 seconds after a PTY is selected PTY seek 1 When you press the II button the PTY select mode is turned on 2 Select PTY 3 Press the lt d or P gt button If you press the P gt button the unit seeks a PTY broadcast moving up the frequencies if you press the lt d button it seeks moving down the frequencies If no station with the selected PTY broadcast can be received the unit returns to the previous mode DXZ448R 1 7 RDS Operations PTY preset memory 3 If you press and hold any one of the 1 When you press the PH button the PTY DIRECT buttons for 2 seconds or longer select mode is turned on the selected PTY is stored into that preset 2 Turn the ROTARY knob clockwise or ane counterclockwise to select the desired PTY The 29 types of PTY below can be selected PTY item ENGLISH GERMAN NEWS NACHRICH NYHETER SWEDISH FRENCH INFOS Contents News AFFAIRS AKTUELL AKTUELLT MAGAZINE Today s e
11. Programme Type standby mode or PTY items Play or pause a CD while in the CD mode lt 4 gt buttons Select a station while in the radio mode or select a track when listening to a CD These buttons are used to make various settings Press and hold the button for 1 second or longer to switch the fast forward fast backward BND button Switch the band or seek tuning or manual tuning while in the radio mode Play a first track while in the CD mode A M button Use the button to switch to the audio mode bass treble balance fader Z Enhancer Plus Magna Bass Extended adjustment FNC button Press the button to turn on the power Press and hold the button for 1 second or longer to turn off the power Switch the operation mode among the Radio mode etc Major Button Operations When External Equipment is Connected to This Unit e When the CD DVD changer is connected For details see the section CD changer operations For the DVD changer refer to the Owner s Manual provided with the DVD changer DISP button When the button is pressed and held switches the user titles or track titles etc while in the CD changer mode T button Use the button to input a title in the CD changer mode Use the button to scroll the title during CD text play UP DN buttons Select the disc RDM button Perform random play Also perform disc random play when the button is
12. a failure of DVD mechanism and consult your store of purchase ERROR 3 A DISC cannot be played due to scratches etc Retry or replace with a non scratched non warped disc ERROR 6 A DISC inside the DVD changer cannot be played because it is loaded upside down Eject the disc then reload it properly ERROR P Parental level error Set the correct Parental level ERROR R Region code error Eject the disc and replace correct region code disc AMP GRD The speaker protection circuit is operating During this operation if any volume operation is performed the display shows AMP GRD 1 Turn down sound volume Function can also be restored by turning the power off and on again Speaker volume is reduced automatically when the speaker protection circuit operates If the sound is muted again consult our service department If an error display other than the ones described above appears press the reset button If the problem persists turn off the power and consult your store of purchase 32 DXZ448R 10 SPECIFICATIONS Radio section Tuning System PLL synthesizer tuner Receiving Frequencies FM 87 5to 108 MHz 0 05 MHz steps MW 531 to 1602 kHz 9 kHz steps LW 153to 279 kHz 3 kHz steps CD player section System Compact disc digital audio system Frequency Response 10 Hz to 20 kHz 1 dB Signal to Noise Ratio 100 dB 1 kHz Dynamic Range 95 dB 1
13. kHz Distortion 0 0196 Note General Output Power 4 X 27 W DIN 45324 B 14 4V Power Supply Voltage 14 4 V DC 10 8 to 15 6 V allowable negative ground Power Consumption Less than 15 A Speaker Impedance 4 Q 4 to 8 Q allowable Auto Antenna Rated Current 500 mA or less Weight Main unit 1 2 kg Dimensions Main unit 178 W X 50 H X 155 D mm Specifications and design are subject to change without notice for further improvement DXZ448R 33
14. knob MUTE The sound from this unit is muted during telephone calls Press the T button to return to the previous mode Turning the screen saver function on or off This unit is provided with the screen saver function which allows you to show various kinds of patterns and characters in the Operation Status indication area of the display in a random order You can turn on and off this function If the button operation is performed with the screen saver function on the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display 1 The factory default setting is SS Press and hold the T button for 1 second or longer to switch to the adjustment selection display Press the lt d or P gt button and select SCRN SVR Press the gt If button Turn the ROTARY knob clockwise or counterclockwise to select the setting Each time you turn the ROTARY knob the setting changes in the following order OFF SS gt MESSAGE Press the gt I button to store the setting Press the T button to return to the previous mode 21 DXZ448R Operations Common to Each Mode Entering titles Titles up to 8 characters long can be stored in memory and displayed for CD CD changer and TV stations The number of titles that can be entered for each mode are as follows Mode Number of titles CD mode 50 titles TV mode 20
15. pressed and held RPT button Perform repeat play When this button is pressed and held disc repeat play is performed SCN button Perform scan play for 10 seconds of each track Disc scan play is performed when the button is pressed and held gt I button Play or pause a CD or DVD lt 4 D gt buttons e Select a track when listening to a disc Press and hold the button for 1 second or longer to switch the fast forward fast backward BND button Move the next disc in increasing order e When the TV DAB is connected For details see the section TV operations or DAB operations AF button Press the button to turn on or off the AF Alternative Frequency function in the DAB mode This function is only DAB tuner TA button Use the button to set the TA Traffic Announcement standby mode in the DAB mode This function is only DAB tuner P A button Perform preset scan while in the TV mode When the button is pressed and held auto store is performed This function is only TV tuner DIRECT buttons Store a station into memory or recall it directly gt I button Use the button to set the PTY Programme Type standby mode or PTY items in the DAB mode Switch the TV picture mode or VTR external picture mode lt 4 gt gt buttons Select a station BND button Switch the band When the button is pressed and held switch S
16. the display and disc scan play starts 2 To cancel disc scan play press the SCN button again DISC and SCN go off from the display and the current track continues to play Repeat play Repeat play continuously plays the current track This function continues automatically until it is cancelled 1 Press the RPT button RPT lights in the display and the current track is repeated 2 To cancel repeat play press the RPT button again RPT goes off from the display and normal play resumes Disc repeat play After all the tracks on the current disc have been played disc repeat play automatically replays the current disc over from the first track This function continues automatically until it is cancelled 1 Press and hold the RPT button for 1 second or longer DISC and RPT light in the display and disc repeat play starts 2 To cancel disc repeat play press the RPT button again DISC and RPT go off from the display and normal play resumes on the current track CD Changer Operations Random play Random play selects and plays individual tracks on the disc in no particular order This function continues automatically until it is cancelled 1 Press the RDM button RDM lights in the display and random play begins 2 To cancel random play press the RDM button again RDM goes off from the display and normal play resumes Disc random play The disc random play selec
17. 1 3 Press one of the DIRECT buttons to recall a preset programme Note Press and hold the DIRECT button for 2 seconds or longer to store the programme currently being received Manual memory AF function The AF function switches to a different frequency on the same network in order to maintain optimum reception The factory default setting is ON If the reception of the current broadcast station deteriorates SEARCH appears in the display and the radio searches for the same programme on another frequency For details on AF function refer to the section RDS operation of each owner s manual e Switching OFF the AF function e Switching ON the AF function AF function between RDS and DAB When the same programme is broadcast by both RDS and DAB and this function is ON the main unit switches to receiving the broadcast with the better reception automatically TA Traffic Announcement In the TA standby mode when a traffic announcement broadcast starts the traffic announcement broadcast is received as top priority regardless of the function mode Traffic programme TP automatic tuning is also possible This function can only be used when TP is lit in the display When TP is lit this means that the DAB or RDS broadcast station being received has traffic announcement programmes x For details on TA refer to the section RDS operation of each owner s manual
18. 1 Press the BND button and select the desired band FM or AM MW LW 2 Tune into a station If MANU is lit in the display press and hold the BND button for 1 second or longer MANU in the display goes off and seek tuning is now available If TA is lit in the display TP stations are automatically sought e DX SEEK Press the lt d or P gt button to automatically Seek a station When the P gt button is pressed the station is sought in the direction of higher frequencies if the lt 4 button is pressed the station is sought in the direction of lower frequencies When seek tuning starts DX appears in the display LOCAL SEEK If you press and hold the lt d or b gt button for 1 second or longer local seek tuning is carried out Broadcast stations with good reception sensitivity are selected When local seeking starts LO appears in the display Radio Operations Manual tuning There are 2 ways available Quick tuning and step tuning When you are in the step tuning mode the frequency changes one step at a time In the quick tuning mode you can quickly tune the desired frequency 1 Press the BND button and select the desired band FM or AM MW LW If MANU is not lit in the display press and hold the BND button for 1 second or longer MANU is lit in the display and manual tuning is now available 2 Tune ina station e Quick tuning
19. 8 IN CASE OF DIFFICULTY Problem Power does not turn on No sound is pro duced Fuse is blown Measure Replace with a fuse of the same amperage If the fuse blows again consult your store of purchase Incorrect wiring Consult your store of purchase No sound output when operating the unit with amplifiers or power antenna at tached Power antenna lead is shor ted to ground or excessive current is required for re mote on the amplifiers or power antenna 1 Turn the unit off 2 Remove all wires attached to the power antenna lead Check each wire for a possible short to ground using an ohm meter 3 Turn the unit back on 4 Reconnect each amplifier remote wire to the power antenna lead one by one If the amplifiers turn off before all wires are attached use an external relay to provide remote on voltage excessive current required Nothing happens when buttons are pressed Display is not accu rate The microprocessor has malfunctioned due to noise etc Turn off the power then press the RELEASE button and remove the DCP Press the reset button for about 2 seconds with a thin rod Reset button DCP or main unit connec tors are dirty Wipe the dirt off with a soft cloth moistened with cleaning alcohol Compact disc cannot be loaded Another compact disc is al ready loaded Eject the compact disc before loading the new one Sound skips or i
20. A standby mode when a traffic announce ment broadcast starts the traffic announcement broadcast is received as top priority regardless of the function mode so you can listen to it Traffic programme TP automatic tuning is also possible This function can only be used when TP is lit in the display When TP is lit this means that the RDS broadcast station being received has traffic announcement programmes OG Setting the TA standby mode If you press the TA button when only TP is lit in the display TP and TA light in the display and the unit is set into the TA standby mode until a traffic announcement is broadcast When a traffic announcement broadcast starts TRA INFO appears in the display If you press the TA button while a traffic announcement broadcast is being received the traffic announcement broadcast reception is cancelled and the unit goes into the TA standby mode e Cancelling the TA standby mode As TP and TA lit in the display press the TA button The TA in the display goes off and the TA standby mode is cancelled If TP is not lit pressing the TA button searches for a TP station Searching for a TP station When TP is not lit if you press the TA button TA in the display lights and the unit automatically receives a TP station Note Ifa TP station is not received the unit continues the search operation Pressing TA button again goes off TA
21. Button Operations When External Equipment is Connected to This Unit ux Display Items 8 PGS CECI PR ES LET UT ERE ML 5 REMOTE CONTROL Optional Inserting the Batteries Functions of Remote Control Unit Buttons 6 OPERATIONS Basic Operations Radio Operations eee RDS Operations ues CD Operaltiors rer Operations Common to Each Mode 7 OPERATIONS OF ACCESSORIES CD Changer Operations sess TV Operations tete nte Digital Radio DAB Operations 8 IN CASE OF DIFFICULTY ERROR DISPLAYS 2 do 0 SPECIFICATIONS eee 1 PRECAUTIONS 1 This unit is applicable for on road 4 wheel vehicle purpose only Use for tractor fork truck bulldozer off road vehicle 2 or 3 wheel motor bicycle marine boat or other special purpose vehicle is not appropriate 2 When the inside of the car is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible If moisture forms on the disc wipe it off with a soft cloth If moisture forms on the optical parts of the player do not use the player for about one hour The condensation will disappear naturally allowing normal operation
22. CT display Main display Note The display shown in the normal reception mode and the preset reception mode is the same when a DAB station is received 3 When the unit does not receive a DAB station the display changes in the following order Normal reception mode DXZ448R 27 Digital Radio DAB Operations Preset reception mode Notes The number of programmes and broadcasting times depend on the DAB stations When the strength of DAB signals is weak audio output is muted Seek tuning T 2 Press the FNC button to select the DAB mode Press and hold the lt d or P gt button for 1 second or longer SEARCH appears in the display DAB lights up in the display when the main unit receives a DAB station The main unit stops the seek tuning when it cannot find a DAB station The display returns to the previous mode Manual tuning T 2 Press the FNC button to select the DAB mode Press and hold the BND button for 1 second or longer MANU lights up in the display Press the lt d or P gt button to select a station If no operation is performed for more than 7 seconds manual tuning is cancelled and the display returns to the previous mode Switching programmes 1 2 Press the FNC button to receive a DAB station Press the lt d or gt button to switch programmes in the DAB station Note The p
23. Clarion Owner s manual Mode d emploi Bedienungsanleitung Istruzioni per l uso Gebruiksaanwijzing Manual de instrucciones Bruksanvisning Manual de instru es DXZ448R RDS EON FM MW LW RADIO CD COMBINATION COMBINE RADIO FM PO GO RDS EON LECTEUR DE CD RDS EON UKW MW LW RADIO CD KOMBINATION COMBINAZIONE DI RADIO RDS EON FM MW LW E LETTORE CD RDS EON FM MW LW RADIO CD COMBINATIE COMBINACI N DE RADIO RDS EON DE FM MW LW Y REPRODUCTOR DE CD KOMBINERAD FM MV LV RADIO MED RDS EON OCH CD SPELARE COMBINAC O DE CD COM R DIO FM MW LW RDS EON a D y ih ih HI HR I Up koas CAF2 CRE HH UH COMPACT DIGITAL AUDIO TEXT CARDS i CONNECTOR Thank you for purchasing this Clarion product Please read this owner s manual in its entirety before operating this equipment After reading this manual be sure to keep it in a handy place e g glove compartment Check the contents of the enclosed warranty card and keep it carefully with this manual This manual includes the operating procedures of the CD changer DVD changer DAB and TV tuner connected via the CeNET cable The CD changer DVD changer and TV tuner have their own manuals but no explanations for operating them are described CAUTIONS This appliance contains a laser system and is classified as a CLASS 1 LASER PROD
24. Setting the TA standby mode e Cancelling the TA standby mode Searching for a TP station Notes Ifa TP station is not received the main unit stops the search operation TP may be lit in the display when a TP broadcast is transmitted from an RDS station In this case press the TA button to perform TP seek tuning Press the TA button again to return to the previous mode INFO Announcement In the INFO standby mode when the selected announcement programme starts the main unit switches to the selected announcement programme automatically Digital Radio DAB Operations Setting the INFO standby mode If you press and hold the TA button for 1 second or longer INFO lights in the display and the main unit is set into the INFO standby mode until the selected announcement is broadcast When the selected announcement broadcast starts the announcement item appears in the display If you press and hold the TA button for 1 second or longer while the selected announcement broadcast is being received the selected announcement broadcast reception is cancelled and the main unit goes into the INFO standby mode e Cancelling INFO standby mode To cancel the INFO standby mode press and hold the TA button for 1 second or longer e Information select This is a function for selecting INFORMATION ON or OFF in the Information interrupt mode You can set ON up to 6 information items You can select any of the 6 it
25. T bass emphasized IMPACT bass and treble emphasized EXCITE bass and treble emphasized mid de emphasized CUSTOM user custom Z OFF no sound effect Adjusting the tone Press the A M button and select the item to adjust Each time you press the A M button the item changes as following order e When B BOOST is set B BOOST gt BAL 0 gt function mode When IMPACT is set IMPACT gt BAL 0 gt function mode When EXCITE is set EXCITE gt BAL 0 gt function mode When CUSTOM is set BASS gt TREBLE gt gt Last function mode When Z OFF is set BAL 0 gt FAD 0 Last function mode FAD 0 2 Last FAD 0 gt Last FAD 0 2 Last BAL 0 2 FAD 0 Adjusting the bass Gain Frequency Q curve This adjustment can be performed when the Z Enhancer Plus is set to CUSTOM 1 Press the A M button and select BASS 2 Turning the ROTARY knob clockwise emphasizes the bass turning it counterclockwise attenuates the bass The factory default setting is B lt G 0 gt Adjustment range 6 to 6 3 Press the lt d or P gt button to select B lt F 60 gt Turning the ROTARY knob clockwise or counterclockwise to select the frequency The factory default setting is B lt F 60 gt Adjustment 60 100 200 Hz 4 Press the lt d or gt button to select B
26. UCT To use this model properly read this Owner s Manual carefully and keep this manual for your future reference In case of any trouble with this player please contact your nearest AUTHORIZED service station To prevent direct exposure to the laser beam do not try to open the enclosure USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE ADVARSEL Denne maerking er anbragt udvendigt pa apparatet og indikerer at apparatet arbejder med laserstr ler af klasse 1 hvilket betyder at der anvendes laserstr ler af svageste klasse og at man ikke pa apparatets yderside kan blive udsat for utilladelig kraftig str ling APPARATET BOR KUN BNES AF FAGFOLK MED S ERLIGT KENDSKAB TIL APPARATER MED LASERSTRALER Indvendigt i apparatet er anbragt den her gengivne advarselsmeekning som advarer imod at foretage s danne indgreb i apparatet at man kan komme til at udsazette sig for laserstr ling 2 DXZ448R Apparaten innehaller laserkomponenten som avger laserstr lning verstigande gransen for laserklass 1 Suojakoteloa si saa avata Laite sisaltaa laserdiodin joka lahettaa nakymatonta silmille vaarallista lasers teily clarion 12V GROUND LW 153 279kHz MW 531 1602kHz FM UKW 87 5 108MHz 87 5 108MHz This unit is designed for on road vehicle purpose U designed for on road vehicle p
27. ay press and hold the BND button for 1 second or longer MANU in the display goes off and seek tuning is now available 2 Press the lt d or P gt button to automatically seek a station Press the P gt button to auto matically tune up the frequency band to the next available TV station press the lt d button to automatically tune down Manual tuning There are 2 ways available Quick tuning and step tuning When you are in the step tuning mode the frequency changes one step at a time In the quick tuning mode you can quickly tune the desired frequency 26 DXZ448R 1 Press the BND button and select the desired band TV1 or TV2 If MANU is not lit in the display press and hold the BND button for 1 second or longer MANU lights in the display and manual tuning is now available 2 Tune into a station e Quick tuning Press and hold the lt d or gt button for 1 second or longer to tune in a station OG Step tuning Press the lt d or P gt button to manually tune in a station If no operation is performed for more than 7 seconds manual tuning is cancelled and the display returns to the previous mode Recalling a preset station A total of 12 TV stations can be stored 6 TV1 and 6 TV2 This allows you to select your favorite TV stations and store them in memory for later recall 1 Press the BND button and select the desired TV band TV1 or TV2 2 To recall a stored TV stat
28. broadcast is received all the function mode operations are stopped ALARM appears in the display and the emergency broadcast can be heard Cancelling an emergency broadcast If you press the AF button emergency broadcast reception is cancelled Switching the PTY display language You can select one of 4 languages English German Swedish or French for the PTY displayed in the display The factory default setting is ENGLISH 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button and select LANGUAGE 3 Press the I button 4 Turn the ROTARY knob clockwise or counterclockwise to select the desired language 5 Press the I button 6 Press the T button to return to the previous mode Volume setting of TA emergency broadcast ALARM and PTY The volume for TA ALARM and PTY interrupts can be set during TA ALARM or PTY interrupt The factory default setting is 15 During a TA ALARM or PTY interrupt turn the ROTARY knob clockwise or counterclockwise to set the volume to the desired level 0 to 33 When the TA ALARM or PTY interrupt ends the volume returns to the level it had before the interrupt CD Operations Loading a CD Insert a CD into the centre of the CD SLOT with the labeled side facing up LOADING appears in the display the CD enters into the slot and the play starts For
29. e Buttons and Their Functions RELEASE button Deeply push in RELEASE button to unlock the DCP ROTARY knob Adjust the volume by turning the knob clockwise or counterclockwise Use the knob to perform various settings CD SLOT CD insertion slot 4 button Eject a CD when it is loaded into the unit AF button Press the button to turn on or off the AF Alternative Frequency function When the button is pressed and held Regional function can select ON or OFF Z button Use the button to select one of the 4 types of sound characteristics already stored in memory TA button Use the button to set the TA Traffic Announcement standby mode DISP button Switch the display indication Main display Sub display Clock display T button Use the button to input a title in the CD mode Press and hold the button for 1 second or longer to enter the adjust mode P A button Perform preset scan while in the radio mode When the button is pressed and held auto store is performed UP DN buttons Select the disc 6 DXZ448R DIRECT buttons Store a station into memory or recall it directly while in the radio mode RDM button Perform random play while in the CD mode RPT button Repeat play while in the CD mode SCN button Perform scan play for 10 seconds of each track while in the CD mode gt I button Use the button to set the PTY
30. eek tuning or manual mode DXZ448R 7 4 DCP The control panel can be detached to prevent theft When detaching the control panel store it in the DCP DETACHABLE CONTROL PANEL case to prevent scratches We recommend taking the DCP with you when leaving the car Removing the DCP 1 Press the FNC button for 1 second or longer to switch off the power 2 Press the RELEASE button RELEASE button The DCP is unlocked 3 Remove the DCP d the DCP Insert the right side of the DCP into the main unit 2 Insert the left side of the DCP into the main unit Storing the DCP in the DCP Case Hold the DCB in the orientation as shown in the figure below and put it into the supplied DCP case Ensure the DCP is in the correct orientation ACAUTION The DCP can easily be damaged by shocks After removing it be careful not to drop it or subject it to strong shocks When the Release button is pressed and the DCP is unlocked the car s vibrations may cause it to fall To prevent damage to the DCP always store it in its case after detaching it ee figure below The connector connecting the main unit and the DCP is an extremely important part Be careful not to damage it by pressing on it with fingernails screwdrivers etc Main Unit Front DCP Rear Panel DCP connector Main unit connector Note f the DCP is dirty wipe off the dirt with a soft dry cloth only
31. ems below INFORMATION item Contents Transport flash Warning Service ENGLISH TRAVEL WARNING NEWS WEATHER EVENT SPECIAL News flash Area weather flash Event announcement Special event 1 Perform the following operation depending on the connected model Press and hold the T button for 1 second or longer 2 Press the lt d or P gt button to select INFO SEL then press the PHI button to enter INFO SEL mode 3 Press the lt d or b gt button to select an information item You can select any of 6 items TRAVEL WARNING gt NEWS gt WEATHER gt EVENT gt SPECIAL gt TRAVEL gt 4 Perform the following operation depending on the connected model Turn the ROTARY knob clockwise or counterclock wise to set the information item for ON or OFF 5 Press the II button to store the setting 6 Press the T button to return to the previous display DXZ448R 29 Digital Radio DAB Operations PTY This function enables you to listen to the selected programme type irrespective of the function mode One common PTY can be selected for DAB or RDS Of DAB PTY and RDS PTY the PTY which is received earlier takes priority over the other PTY broadcasts are not yet available in all countries In the INFO standby mode INFO stations have priority over PTY stations In the TA standby mode TP stations have priority over PTY stations For de
32. in the display and stops TP station searching Auto store function for TP stations You can automatically store up to 6 TP stations into preset memory If the number of TP can be received less than 6 broadcast stations already stored in memory and left without being overwritten As TA lit in the display press and hold the P A button for 2 seconds or longer The TP stations with the good reception sensitivity are stored into preset memory Even if you select FM1 or FM2 a TP station is stored into memory for FM3 PTY This function enables you to listen to a broadcast of the selected programme type even if the unit is on a function mode other than radio RDS Operations Some countries do not yet have PTY broadcast In the TA standby mode a TP station has priority over a PTY broadcast station Setting the PTY standby mode When you press the IE button PTY lights in the display and the PTY standby mode is turned on When the selected PTY broadcast starts the PTY item name appears in the display Cancelling the PTY standby mode When you press and hold the H button for 1 second or longer PTY goes off in the display and PTY standby mode is cancelled e Cancelling a PTY interrupt broadcast Press the II button during the PTY interrupt broadcast the PTY interrupt is cancelled and the unit returns to PTY standby mode s ea PTY When you press the I button the unit goes into
33. ion press the desired DIRECT button to select that station Press and hold one of the DIRECT buttons for 2 seconds or longer to store the current station into preset memory Manual memory 1 Select the desired station with seek tuning manual tuning or preset tuning 2 Press and hold one of DIRECT buttons for 2 seconds or longer to store the current station into preset memory Auto store Auto store selects 6 TV stations automatically and stores each one into preset memory If there are not 6 stations with good reception stations previously stored in memory remain and only the strong stations are stored into memory 1 Press the BND button and select the desired TV band TV1 or TV2 2 Press and hold the P A button for 2 seconds or longer The stations with good reception are stored automatically to the preset channels TV Operations Preset scan Preset scan allows the user to view each preset position before it automatically advances to the next preset This function is useful for searching for a desired TV station in memory 1 Press the P A button 2 When the desired station is found press the P A button again to remain tuned to that station Note Do not press and hold the P A button for 2 seconds or longer Doing so will trigger the auto store function and start storing stations into memory Setting the TV area When you select the TV area TV reception area the TV tuner area se
34. lt Q 1 gt Turning the ROTARY knob clockwise or counterclockwise to select the Q curve 5 Basic Operations The factory default setting is B Q 1 gt Adjustment 1 1 25 1 5 2 When the adjustment is complete press the A M button several times until the function mode is reached Adjusting the treble Gain Frequency This adjustment can be performed when the Z Enhancer Plus is set to CUSTOM 1 2 Press the A M button and select TREBLE Turning the ROTARY knob clockwise emphasizes the treble turning it counterclockwise attenuates the treble The factory default setting is T G 0 gt Adjustment range 6 to 6 Press the lt d or P gt button to select T F 10 gt Turning the ROTARY knob clockwise or counterclockwise to select the frequency The factory default setting is T F 10 gt Adjustment 10 kHz 15 kHz When the adjustment is complete press the A M button several times until the function mode is reached E the balance 2 Press the A M button and select BAL 0 Turning the ROTARY knob clockwise emphasizes the sound from the right speaker turning it counterclockwise emphasizes the sound from the left speaker The factory default setting is BAL 0 Adjustment range L13 to R13 When the adjustment is complete press the A M button several times until the function mode is reached AG nii the fader 2 P
35. mode AF _ Alternative Frequency PS Programme Service Name PTY Programme Type EON Enhanced Other Network TP Traffic Programme RDS interrupt does not function during AM radio reception When set receives RDS signal and can read PS data PS appears in the display AF function The AF function switches to a different frequency on the same network in order to maintain optimum reception The factory default setting is ON e Switching OFF the AF function Press the AF button AF in the display goes off and the AF function turns off e Switching ON the AF function Press the AF button AF in the display lights and the AF function turns on If the reception of the current broadcast station deteriorates SEARCH appears in the display and the radio searches for the same programme on another frequency AF function between RDS and DAB When the same programme is broadcasted by both RDS and DAB and this function is ON the unit switches to receive the broadcast with the better reception automatically This function only operates when the DAH913 or DAH923 DAB unit sold separately is connected This factory default setting is ON 1 6 DXZ448R 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or gt button to select LINK ACT 3 Turn the ROTARY knob clockwise for ON or counterclockwise for
36. o play Repeat play The repeat play continuously plays the current track This function continues automatically until it is cancelled 1 Press the RPT button RPT lights in the display and the current track is repeated 2 To cancel the repeat play press the RPT button again RPT goes off from the display and normal play resumes Random play The random play selects and plays individual tracks on a disc in no particular order This function continues automatically until it is cancelled 1 Press the RDM button RDM lights in the display an individual track is selected randomly and play begins 2 To cancel the random play press the RDM button again RDM goes off from the display and normal play resumes Operations Common to Each Mode Dimmer conirol You can set the dimmer control ON or OFF The factory default setting is ON 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button to select DIMMER 3 Turn the ROTARY knob clockwise or counterclockwise and select ON or OFF 4 Press the T button to return to the previous mode Setting the car speaker output for the cellular phone Optional TEL 002 The factory default setting is RIGHT To output the telephone calls set the cellular phone interrupt to ON 1 Press and hold the T button for 1 second o
37. on to Each Mode 6 Turn the ROTARY knob to select the desired character 7 Repeat step 4 to 6 to enter up to 30 characters for message 8 Press and hold the II button for 2 seconds or longer to store the message in memory and cancel input message mode Press the BND button can cancel the input message Then press and hold the BHI button for 2 seconds or longer to store the message and the message return to default setting 9 Press the T button to return to the previous mode DXZ448R 23 7 OPERATIONS OF ACCESSORIES CD Changer Operations CD changer functions When an optional CD changer is connected through the CeNET cable this unit controls all CD changer functions This unit can control a total of 2 changers Press the FNC button and select the CD changer mode to start play If 2 CD changers are connected press the FNC button to select the CD changer for play If NO MAG appears in the display insert the magazine into the CD changer DISC CHK appears in the display while the player loads checks the magazine If NO DISC appears in the display eject the magazine and insert discs into each slot Then reinsert the magazine back into the CD changer Note Some CDs recorded in CD R CD RW mode may not be usable ACAUTION CD ROM discs cannot be played from every CD changer it s depended on the model Pausing play 1 Press the II button to pause
38. play PAUSE appears in the display 2 To resume play press the PII button again Displaying CD titles This unit can display title data for CD text CDs and user titles input with this unit Title data for CD text CDs can be displayed with this unit only when it is connected to CDC655Tz When connected to DCZ628 or CDC1255z Press the DISP button to display the title When connected to CDC655Tz 1 Press the DISP button to display the title 2 Each time you press and hold the DISP button for 1 second or longer the title display changes in the following order User title disc gt CD text title disc gt Artist name gt CD text title track gt User title disc 24 DXZ448R Notes If the CD playing is not a CD text CD or no user title has been input NO TITLE appears in the display If a CD text CD is not input its disc title or a track title NO TITLE appears in the display Procedure to scroll a title Set SCROLL to ON or OFF The factory default setting is ON Refer to the subsection Turning the screen saver function on or off in section Operation common to each mode When set to ON The title is automatically kept scrolling When set to OFF To scroll just 1 time when the title was changed or the T button was pressed Selecting a CD Press the DN or the UP button to select the desired disc If a CD is not loaded in a slo
39. principale Hoofdtoestel Unidad principal Huvudenhet Unidade principal CD SLOT al a F Clarion B i Z in gt y A Teena C PJ gt DISP TH DIRECT UP D gt DN IT lt 4 gt gt scN IA RPT RDM Note Be sure to unfold this page and refer to the front diagrams as you read each chapter Remarque Veuillez d plier cette page et vous r f rer aux sch mas quand vous lisez chaque chapitre Hinweis Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapitel die Frontdiagramme beachten Nota Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo Opmerking Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken Nota Cuando lea los cap tulos despliegue esta p gina y consulte los diagramas Observera Vik ut denna sida f r att kunna se figurerna ver bilstereons framsida medan du l ser de olika kapitlen Nota Certifique se de abrir esta p gina e consulte os diagramas frontais conforme realiza a leitura de cada cap tulo 5 DXZ448R 3 NOMENCLATURE Note Be sure to read this chapter referring to the front diagrams of chapter 2 CONTROLS on page 5 unfold Names of th
40. r longer to switch to the adjustment selection display 2 Press the lt d or P gt button to select TEL SP 3 Turn the ROTARY knob clockwise to select RIGHT or counterclockwise to select LEFT RIGHT Telephone calls can be heard on the front right speaker connected to this unit LEFT Telephone calls can be heard on the front left Speaker connected to this unit 4 Press the T button to return to the previous mode Cellular phone interrupt setting If you connect this unit and your cellular phone with a separately sold unit TEL 002 you can listen to your telephone calls on your car speakers The factory default setting is OFF 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button to select TEL SW 3 Turn the ROTARY knob clockwise or counterclockwise to select the setting Each time you turn the ROTARY knob the setting changes in the following order OFF ON gt MUTE gt OFF e OFF This unit continues normal operation even when the cellular phone is used Note If connecting a hands free kit please ensure the setting is ON to receive the telephone audio through the system ON You can listen to your telephone calls from the speakers connected to this unit When listening to your calls on your car speakers you can adjust the volume by turning the ROTARY
41. ress and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button and select SCROLL 3 Turn the ROTARY knob clockwise or counterclockwise and select ON or OFF ON To scroll automatically OFF To scroll just 1 time when the title was changed or the title key was pressed 4 Press the T button to return to the previous mode Selecting the CONTRAST mode The factory default setting is 5 1 Press and hold the button T for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button to select CONTRAST Turn the ROTARY knob to select from 1 8 4 Press the T button to return to the previous mode e Entering MESSAGE INFORMATION Message up to 30 characters long can be stored in memory and displayed as a type of screen saver setting The factory default setting is WELCOME TO CLARION 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or gt button and select INPUT 3 Press the I button Press the lt d or P gt button to move the cursor 5 Press the DISP button to select a character Each time you press the DISP button the character changes in the following orders Capital letters Numbers Symbols gt Umlaut gt Capital letters Operations Comm
42. ress the A M button and select FAD 0 Turning the ROTARY knob clockwise emphasizes the sound from the front speakers turning it counterclockwise emphasizes the sound from the rear speakers The factory default setting is FAD 0 Adjustment range F12 to R12 When the adjustment is complete press the A M button several times until the function mode is reached DXZ448R 1 3 Basic Operations Adjusting the Z Enhancer Plus 1 Press the Z button and select the Z Enhancer Plus mode to adjust 2 Press the A M button and turning the ROTARY knob clockwise adjusts in the direction turning it counterclockwise adjusts in the direction When B BST 0 is selected you can ad just the bass in the range of 3 to 3 When IMPACT 0 is selected you can ad just the bass and treble in the range of 3 to 3 When EXCITE 0 is selected you can ad just the bass and treble in the range of 3 to 3 Press and hold the Z button for 2 seconds or longer to change to the CUSTOM mode Bass treble characteristics become flat and the indication Z FLAT is shown in the display Press the Z button again to change to the Z OFF mode Adjusting MAGNA BASS EXTEND The MAGNA BASS EXTEND does not adjust the low sound area like the normal sound adjustment function but emphasizes the deep bass sound area to provide you with a dynamic Sound 1 Press and hold the
43. rogramme name may be the same depending on DAB programmes 28 DXZ448R Programme scan This function scans through each receivable programme in a DAB station being received for 10 seconds sequentially This is useful when you want to search for a desired programme 1 Press the FNC button to receive a DAB station 2 Perform the following operation depending on the connected model Press the P A button SERV SCN lights up and the unit starts scanning each programme for 10 seconds sequentially Each time the main unit scans the programme name is shown in the display 3 To stop programme scan when a desired programme is tuned in Press the P A button Manual memory The main unit has a manual memory function for DAB programmes Up to 18 programmes 6 programmes each can be preset in the preset buttons M1 M2 and M3 1 Press the FNC button to select the DAB mode 2 Press the BND button to select any one shown above 3 Press the lt d or P gt button to select a desired programme 4 Press and hold one of the DIRECT buttons 1 to 6 for 2 seconds or longer to store the programme Note The interrupt programme PTY or INFO cannot be written into a manual memory Recalling a preset programme 1 Press the FNC button to select the DAB mode 2 Press the BND button Each time you press the BND button the display changes in the following order M1 gt M2 gt M3 gt M
44. s anti static Spray or thinner to clean compact discs After using special compact disc cleaner let the compact disc dry off well before playing it Ball point pen Roughness Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks If you try to play such a compact disc you may not be able to get it back out of the CD player or it may damage the CD player Do not use compact discs that have large scratches are misshapen cracked etc Use of such discs may cause misoperation or damage To remove a compact disc from its storage case press down on the center of the case and lift the disc out holding it carefully by the edges Be sure to unfold and read the next page Veuillez d plier et vous r f rer la page suivante Bitte ausbreiten und die n chste Seite lesen Assicurarsi di aprire e leggere la pagina successiva Volgende pagina uitvouwen en doorlezen a u b Cerci rese de desplegar y de leer la p gina siguiente Gl m inte att vika ut och l sa n sta sida N o deixe de abrir e ler a pr xima p gina DXZ448R stabilizers etc These may damage the disc or Spuepapen uod SE Co Y s nfn 2 CONTROLS LES COMMANDES REGLER CONTROLLI REGELAARS CONTROLES KONTROLLER CONTROLOS Main unit Appareil principal Hauptger t Apparecchio
45. s noi Sy Compact disc is dirty Clean the compact disc with a soft cloth Compact disc is heavily scratched or warped Replace with a compact disc with no scratches Sound is bad directly after power is turned on Water droplets may form on the internal lens when the car is parked in a humid place Let dry for about 1 hour with the power on DXZ448R 31 9 ERROR DISPLAYS If an error occurs one of the following displays is displayed Take the measures described below to eliminate the problem Error Display ERROR 2 ACD is caught inside the CD deck and is not ejected Measure This is a failure of CD deck s mechanism and consult your store of purchase ERROR 3 ACD cannot be played due to scratches etc Replace with a non scratched non warped disc ERROR 6 A CD is loaded upside down inside the CD deck and does not play Eject the disc then reload it properly CD changer ERROR 2 ACD inside the CD changer is not loaded This is a failure of CD changer s mechanism and consult your store of purchase ERROR 3 ACD inside the CD changer cannot be played due to scratches etc Replace with a non scratched non warped disc ERROR 6 A CD inside the CD changer cannot be played because it is loaded upside down Eject the disc then reload it properly DVD changer ERROR 2 A DISC inside the DVD changer cannot be played This is
46. sition Note If you force a CD into before auto reloading this can damage the CD If a CD 12 cm is left in the ejected position for 15 seconds the CD is automatically reloaded Auto reload 8 cm CDs are not auto reloaded Be sure to remove it when ejected Selecting a track e Track up 1 Press the gt button to move ahead to the beginning of the next track 2 Each time you press the B button the track advances ahead to the beginning of the next track e Track down 1 Press the lt d button to move back to the beginning of the current track 2 Press the lt d button twice to move to the beginning of the previous track Fast forward fast backward Fast forward Press and hold the B gt button for 1 second or longer Fast backward Press and hold the lt d button for 1 second or longer 20 DXZ448R Top function The top function resets the CD player to the first track of the disc Press the BND button to play the first track track No 1 on the disc Scan play The scan play locates and plays the first 10 seconds of each track on a disc automatically This function continues on the disc until it is cancelled The scan play is useful when you want to select a desired track 1 Press the SCN button to start scan play SCN lights in the display 2 To cancel the scan play press the SCN button again SCN goes off from the display and the current track continues t
47. t channels If auto store is performed in the FM bands the stations are stored in FM3 even if FM1 or FM2 was chosen for storing stations Preset scan Preset scan receives the stations stored in preset memory in order This function is useful when searching for a desired station in memory 1 Press the P A button 2 When a desired station is tuned in press the P A button again to continue receiving that station Note Be careful not to press and hold the P A button for 2 seconds or longer otherwise the auto store function is engaged and the unit starts storing stations DXZ448R 1 5 RDS Operations RDS Radio Data System This unit has a built in RDS decoder system that supports broadcast stations transmitting RDS data This system can display the name of the broadcast station being received PS and can automatically switch to the broadcast station with the best reception as you move long distances AF switching Also if a traffic announcement or programme type is broadcast from an RDS station no matter what mode you are in this broadcast is received Additionally if EON information is received this information enables automatic switching of other preset stations on the same network and interruption of the station being received with traffic information from other stations TP This function is not available in some areas When using the RDS function always set the radio to FM
48. t of magazine pressing the UP or the DN button cannot work Selecting a track e Track up 1 Press the gt gt button to move ahead to the beginning of the next track 2 Each time you press the J gt button the track advances ahead to the beginning of the next track Ge Track down 1 Press the lt d button to move back to the beginning of the current track 2 Press the lt d button twice to move to the beginning of the previous track Fast forward fast backward Fast forward Press and hold the B button for 1 second or longer Fast backward Press and hold the lt 4 button for 1 second or longer Scan play Scan play locates and plays the first 10 seconds of each track on a disc automatically This function continues on the disc until it is cancelled The scan play is useful when you want to select a desired track 1 Press the SCN button to start track scanning SCN lights in the display 2 To cancel the scan play press the SCN button again SCN goes off from the display and the current track continues to play Disc scan play Disc scan play locates and plays the first 10 seconds of the first track on each disc in the currently selected CD changer This function continues automatically until it is cancelled Disc scan play is useful when you want to select a desired CD 1 Press and hold the SCN button for 1 second or longer DISC and SCN light in
49. tails on PTY refer to the section RDS operation of each owner s manual OG Setting the PTY standby mode e Cancelling the PTY standby mode e Cancelling a PTY interrupt broadcast Oe Selecting PTY PTY seek PTY preset memory Emergency broadcast When an emergency broadcast is received all the function mode operations are stopped ALARM appears in the display and the emergency broadcast can be heard For details on Emergency broadcast refer to the section RDS operation of each owner s manual e Cancelling an emergency broadcast Switching the PTY and INFO display language You can select one of 4 languages English German Swedish or French for the PTY and INFO shown in the display x The factory default setting is ENGLISH For details on Switching the PTY display language refer to the section RDS operation of each owner s manual 30 DXZ448R Volume setting of TA INFO emergency broadcast ALARM and PTY The volume for TA INFO ALARM and PTY interrupts can be set during TA INFO ALARM and PTY interrupt Perform the following operation depending on the connected model The factory default setting is 15 During a TA INFO ALARM or PTY interrupt turn the ROTARY knob clockwise or counterclockwise to set the volume to a desired level 0 to 33 When the TA INFO ALARM or PTY interrupt ends the volume returns to the level it had before the interrupt
50. titles CD changer mode Number of titles DCZ628 connected CDC655Tz connected 100 titles CDC1255z connected 50 titles 1 Press the FNC button to select the mode you want to enter a title CD CD changer or TV 2 Select and play a CD in the CD changer or tune in to a TV station for which you want to enter the title 3 Press the DISP button and display the sub 4 Press the T button 5 Press the lt d or P gt button to move the cursor 6 Press the DISP button to select a character Each time you press the DISP button the character changes in the following order Capital letters Numbers Symbols Umlaut Capital letters 7 Turn the ROTARY knob to select the desired character 8 Repeat steps 5 to 7 to enter up to 8 characters for the title 9 Press and hold the BII button for 2 seconds or longer to store the title into memory and cancel title input mode 100 titles Clearing titles 1 Select and play a CD in the CD changer or tune in to a TV station for which you want to clear the title 2 Press the DISP button and display the sub 3 Press the T button and switch the display to the title input display 4 Press the BND button 5 Press and hold the WII button for 2 seconds or longer to clear the title and cancel title input mode 22 DXZ448R Setting the method for title scroll Set how to scroll in CD TEXT The factory default setting is ON 1 P
51. ts and plays individual tracks or discs automatically in no particular order This function continues automatically until it is cancelled 1 Press and hold the RDM button for 1 second or longer DISC and RDM light in the display and disc random play starts 2 To cancel disc random play press the RDM button again DISC and RDM go off from the display and normal play resumes from the current track DXZ448R 25 TV Operations TV tuner functions When an optional TV tuner is connected through the CeNET cable this unit controls all TV tuner functions To watch TV requires a TV tuner and monitor eee aTV Press the FNC button and select the TV mode 2 Press the BND button to select the desired TV band TV1 or TV2 Each time the button is pressed the input selection toggles between TV1 and TV2 3 Press the lt d or P gt button to tune in the desired TV station Watching a video The TV tuner has a VTR input terminal to which 1 external device can be connected Connect a 12 V video cassette player VCP or video cassette recorder VCR to the TV tuner input terminal 1 Press the II button to select VTR 2 To return to the TV broadcast press the 511 button Tuning There are 3 types of tuning mode available Seek tuning manual tuning and preset tuning Seek tuning 1 Press the BND button and select the desired TV band TV1 or TV2 If MANU is lit in the displ
52. tting changes 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button to select TV AREA 3 Press the WII button 4 Turn the ROTARY knob clockwise or counterclockwise to select the reception area 5 Press the II button 6 Press the T button to return to the previous mode Setting the TV diver You can change the reception setting for the TV antenna connected to the TV tuner 1 Press and hold the T button for 1 second or longer to switch to the adjustment selection display 2 Press the lt d or P gt button to select TV DIVER 3 Turn the ROTARY knob clockwise to set to ON or counterclockwise to set to OFF ON Sets reception emphasizing the visual e OFF Sets the diver setting to OFF 4 Press the T button to return to the previous mode Digital Radio DAB Operations DAB control function When a CeNET cable is used to connect a DAB DAH913 or DAH923 sold separately all functions can be operated d to the DAB station Press the FNC button to select the DAB mode 2 When the unit receives a DAB station the display changes in the following order Frequency channel gt service label Switching displays Press the DISP button to select the desired display Each time you press the DISP button the display switches in the following order Main display Clock
53. urpose CLASS 1 LASER PRODUCT Clarion Co Ltd MADE INCL 31 Display Items Enter indication WWD Manual indication Operation status indication Titles PS names PTYs CT clock etc are displays Preset channel indication 1 to 6 Disc number indication 1 to 12 Z Enhancer Plus indication DAB DAB indication CAFD Alternative frequency indication CREG2 Regional indication CTAD Traffic announcement indication C TP Traffic programme indication CPTYD Programme type indication CINFOD Information indication for DAB a lt id k a 4 a DAB CAFD CREG2 CTAD CTP CPTY2 CINFO2 L M _M B EX CIE3 gt SCNJ RPT J RDMJ MOMS MAGNA BASS EXTEND indication Stereo indication for DAB Disc indication C SCN J Scan indication C RPT J Repeat indication CRDM J Random indication QU Mute indication LCD Screen In extreme cold the screen movement may slow down and the screen may darken but this is normal The screen will recover when it returns to normal temperature 8 DXZ448R Contents 1 PRECAUTIONS EE 3 handing Compact DISCS esere uu u u Sua asua ee cade tate uio cen ient tat zer 4 2 nodos M 5 3 NOMENCLATURE eene wn 6 Names of the Buttons and Their Functions 5 0 Major
54. vents INFO SERVICE INFO SERVICES Information SPORT SPORT SPORT SPORT Sports EDUCATE BILDUNG UTBILDN EDUCATIF Education DRAMA H6R LIT TEATER FICTION Drama CULTURE KULTUR KULTUR CULTURE Culture SCIENCE WISSEN VETENSKP SCIENCES Science VARIED UNTERH UNDERH DIVERS Variety POP M POP POP M POP Pop music ROCK M ROCK ROCK M ROCK Rock music EASY M U MUSIK LaTTLYSS CHANSONS Easy music LIGHT M L MUSIK L KLASS M CL L G Light music CLASSICS E MUSIK KLASSISK CLASSIQ Classics OTHER M MUSIK VRIG M AUTRE M Other music WEATHER WETTER V DER M T O Weather FINANCE WIRTSCH EKONOMI ECONOMIE Finance CHILDREN KINDER FOR BARN ENFANTS For children SOCIAL SOZIALES SOCIALT SOCI T Social RELIGION RELIGION ANDLIGT RELIGION Religion PHONE IN ANRUF TELEFON FORUM Phone in TRAVEL REISE RESOR VOYAGES Travel LEISURE FREIZEIT FRITID LOISIRS Leisure JAZZ JAZZ JAZZ JAZZ Jazz COUNTRY COUNTRY COUNTRY COUNTRY Country NATION M LANDES M NATION M CH PAYS Nation music OLDIES OLDIES OLDIES R TRO Oldies FOLK M FOLKLORE FOLKM FOLKLORE Folk music DOCUMENT FEATURE DOKUMENT 1 8 DXZ448R DOCUMENT Documentaries RDS oprations Emergency broadcast If an emergency
Download Pdf Manuals
Related Search