Clarion CJ-5600E User's Manual
Contents
1. Choose a location where you install the Monitor Clean the place for the Stand with cleanser and remove the Protective Tape And then attach it exactly where you want 2 Fasten the Monitor with Tapping Screw 3 Adjust angle of Stand and install Monitor 4 Connect each connecting cable as in the product installation reference SS Cable Guidance AL Fix Knob Bracket gt IN Gr VEY Stand Base M Y Control Knob Angle E Monitor Cable Connection Tapping Screw i Safeguard tape Installed on the ceiling Normal Installation Troubleshooting Problem Cause No image is displayed properly Is camera connected Measure Check the wiring to the camera and the camera connection Is power cable connected properly Check the wiring Power does not turn on Is a fuse blown out Replace with a fuse of the same amperage 2A Operating Temperature in the car is below 0 C or over Color is washed out environment is 60 C Check to see that the temperature in inappropriate the car is appropriate around 25 C SPECIFICATION ITEM NTSC PAL SCREEN SIZE 5 6 INCH 14 22cm NUMBER OF PIXELS 320 W x 3 RGB x 234 H DOT PITCH 0 118 W x 0 362 H mm PANEL BRIGHTNESS 350 cd m2 DISPLAY AREA 113 28 W x 84 7 H mm CONTRAST RATIO 300 1 VIEW ANGLE2. SUB MENU 3 Press UP DOWN button to change Settings e DIMMER a Ee LANGUAGE ENGLISH DEUTSCH ITALIANO FRANCAIS ESPA ON ror 20 HA DIRECTION Inverted upside down fe 081 NOLLOSYIG N LISI DIRECTION 0 e RESET gt A factory default reset will clear all of OSD information PICTURE SUB MENU 3 Press UP DOWN button to change Settings CONTRAST e BRIGHTNESS e COLOR CONTRAST 70 AST 0 S BRIGHTNESS 70 ESS COLOR 70 a e TINT TINT 50 CAMERA SUB MENU 3 Press UP DOWN button to change Settings e In the mirror mode the screen is inverted laterally CAM1 NORMAL CAM2 NORMAL Connections CAMERA 1 Sold Separately CAMERAZ2 1 Sold Separately 3 GREEN BLACK CAMERA2 CAMERA1 CAMERA2 CAMERA1 1 H 1 Use a Clarion camera BLACK REWER 2 A relay cable sold separately is required GROUND DOINA JAN for connecting the camera 3 Use tape to keep the connection between the monitor cable and the camera relay cable secure BLACK CAMERA 1 priority Standby for rear view Connect this cable to of back gear lamp GREEN CAMERA 2 Standby for side view Connect this cable to of turn signal lamp Installation 1
3. Clarion Owner s manual amp Installation manual Benutzerhandbuch amp Installationshandbuch Manuale dell utente e manuale di installazione Mode d emploi et manuel d installation Manual de instrucciones y de instalaci n CJ 5600E 5 6 TFT LCD COLOR MONITOR 5 6 ZOLL TFT FARBMONITOR MONITOR A COLORITFT DA 5 6 MONITEUR COULEUR TFT 5 6 MONITOR TFT COLOR DE 5 6 1 Before ater tener rrr 3 2 Fes pet ces svecnnt nec eeeecoceseces sect cies 3 3 Names of the Buttons 4 A IN 4 9 COMECUO Sastres esencia 7 Oy Installati n siei 8 7 IHOUDIS NOUS ae us 9 8 Specifications croacia 9 This unit has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This unit generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this unit does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to consult the dealer or an experienced radio TV technician for help E INFORMATION FOR USERS CHANGES OR MODIFICATI
4. D function e 7 Language Display Selection ENGLISH DEUTSCH ITALIANO F RANCAIS ESPANON St H 4 AR O Free voltage From DC12V to DC24V e Dimmer selection function e Picture quality control PWM control e Camera input 2 system Work together with back gear turn signal E Dub a Names of the Buttons POWER MODE O MENU UP DOWN I KL f F STAND BY LED hn Operations POWER 1 Press POWER button to on the power ON OFF STAND BY state is OFF 2 Press POWER button again to off the power STAND BY state is ON 2 MODE Camera Selection E It is a function to change CAMERA CAM1 CAM2 1 Press MODE button CAM1 2 CAM1 or CAM2 appears on the screen and it disappears after 5 seconds CAM1 gt CAM2 Note In the mirror mode the character is inverted 3 MENU E It is a function to select MAIN MENU SETUP PICTURE CAMERA 1 Press MENU button to select MAIN MENU changed color in red when it is selected Every time the button is pressed the setting changes D SETUP PICTURE CAMERA 2 Press MODE button to select SUB MENU changed color in red when it is selected Every time the button is pressed the setting changes e SETUP e PICTURE xt CONTRAST 50 E SUB MENU e CAMERA CAM1 NORMAL CAM2 NORMAL SET UP
5. H U D 65deg 45deg 65deg VOLTAGE DC 12V 24V POWER SUPPLY CURRENT 550mA DC 12V MONITOR SET ONLY REAR INPUT POWER DC 12V 24V INPUT SYSTEM AUTO NTSC PAL HORIZONTAL 15 734 KHz 15 625 KHz FREQUENCY VERTICAL 60Hz 50Hz OSD DISPLAY 7 LANGUAGE USER CONTROLS POWER MODE MENU UP DOWN OPERATING TEMPERATURE 10 C 60 C STORAGE TEMPERATURE 20 C 70 C DIMENSION W x H x D 163 W x 112 H x 30 D WEIGHT 0 3Kg MONITOR CABLE ASS Y ACCESSORIES STAND ASS Y sessussosoessussessessassessassassesoesoassesnesonsssse Caution The design and specifications of this product in order to improve its quality may be changed without notice Clarion Co Ltd All Rights Reserved Copyright 2007 Clarion Co Ltd Printed in Korea Gedruckt in Korea Stampato in Corea 2007 2 Imprim en Cor e Impreso en Corea CJ 5600E
6. ONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL Before Use N Warning e Do Not Back Up Vehicle While Relying Only on the Monitor Image e Use Slow Speeds When Backing Up e The rear view monitor image has the same right left inversion as your vehicle s rearview mirrors Depending on the vehicle the field and angle of view may differ E Precautions when you use the monitor e Do not touch the LCD panel e Use the product at the temperature range of 10 C 60 C O Screen may be a little dark when the product is operated in low temperature areas Screen will show normal luminosity after a few minutes e Do not disassemble and modify the product in any way This may cause fire and or electric shock e When you install the product in a car and watch monitor the car engine should be running as there might occur excessive discharge of the car battery e Any liquid leaking into product may cause malfunction E Precautions when you use the product in a car e The driver should not use the product while he she is driving e Be cautious of humidity and shock when you use the product in a car e Cover the product when exposed to direct rays of the sun for a long period of time You should keep the product at a temperature range of 20 C 70 C Features e Application of 5 6 TFT LCD with high resolution and low reflection e All functions are displayed on screen OS
Download Pdf Manuals
Related Search