Clam Corp Thermal X 8280 User's Manual
Contents
1. p n 102071 12 Step Ten e To set the Tent from outside the Shelter grasp the Tent Material under the Link Door and pull it downward Observe the Porch Area of the Tent lifting accordingly as you pr When the U Channel Molding is correctly installed the Canopy Hoop Pole in the Porch Area will lightly touch the floor e To achieve this condition start by finding the center of the Molding From behind the unit pull the Tent Material under the Link Door downward and fold the Tent Material under the Lip of the Base Fold the Molding in half to find the midpoint Take the midpoint of the Molding and press it onto the Tent material that you have folded over the Base Lip Continue pressing the Molding outward in both directions until you have secured about twelve inches of material to the Base e Having temporarily secured the Tent to the Base take a walk around the unit Readjust the Molding until you have verified the proper position of the Canopy Hoop Pole vs the floor in the Porch Area Also check that the Tent sides and corners are properly proportioned e When satisfied continue applying the Molding around the Shelter one direction from center and then the other gathering the Tent Material as you go so that surface is relatively wrinkle free and snug Continue until both ends of the Molding are completely pressed on Note You may need to trim the Molding ends with a Side Cutter if they extend beyond the rear edge of the Canopy2. Brackets or if they are not equal From outside the Tent you can feel the Rear Edge of the Canopy Brackets to verify this postion If necessary Trim the Molding a couple inches behind this Rear Edge of the Canopy Bracket e Next install Roof Spreader Poles as indicated With the Roof Spreader Poles in place install and extend he Rear Spreader Poles Do the same with the Front Spreader Poles to take up the remaining slack of the Tent e If everything still looks good secure the Molding with the included 8 ire Screws Evenly space them about every ten to twelve inches and also put a screw in the center of both corners Since there aren t any predrilled holes it s advisable to use a powered driver for this operation Base Li p Short Roof Spreader Pole p n 102078 Long Roof Spreader Pole p n 101839 Tent Material Front Adjustable Spreader Pole p n 101836 U Channel Molding Link Door 8 X 1 2 Long Phillips Screw p n 101930 U Channel Molding p n 102080 Rear Adjustable Spreader Pole p n 101840 Approx 2 Rear Edge of Canopy Bracket 13 Step Eleven e Angle the Seat Assembly slightiv while placing the bottom lip of the Front Seat Bracket under the outside edge of the Base Lip e Tilt the complete assembiv downward so that the Rear Seat Bracket lands upon the Support Tube e Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up aga
3. allation use of inability to use or the repair or replacement of Clam Corporation products Clam Corporation reserves the right to make alterations or modifications in its products at any time which in its opinion may improve the performance and efficiency of the product It shall not be obligated to make such alterations or modifications to products already in service 15
4. inst the i of the Support Tube Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket e Secure the position of the Latch Clip bv pushing it into the two holes located above the horizontal slot of the Rear Seat Bracket e Place Center Console onto the Support Tube as pictured and you are ready to fish l WARNING ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS MOUNTING SYSTEM Base Lip ae Console p n 101458 SECURED POSITION Bracket e Swing the Latch Clip Holes under the Support Tube e Squeeze the Latch Cli and push it through th slot of the Rear Seat Bracket l Tow Rope p n 101095 e Secure bv pushing the ends of the Latch Clip into the holes of the Seat Bracket Knot the ends of the Rope inside the Base after routing through the pre drilled holes _ Support Tube Tips for Use Folding and transporting your Fish Trap is easy u Unsnap the Roof Spreader Poles Rear Spreader Poles and Front Spreader Poles Lay them in the bottom of the base Push the spring buttons and retract each hoop starting with the rear hoop and working towards the front Rotate all retracted hoops to the resting position Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport Cover with the Travel Cover an o
5. mock 16 16 101470 1 4 Dia X 1 2 Long Hex Head Screw 17 10 101486 1 4 Dia X 1 3 4 Long Phillips Screw 18 4 101652 1 1 8 Dia Tube 19 2 101810 Canopy Bracket 20 2 101836 Front Adjustable Spreader Pole 21 1 101839 Long Roof Spreader Pole 22 2 101840 Rear Adjustable Spreader Pole 23 2 101905 Folding Seat Assembly 24 8 101906 1 4 Dia X 2 1 2 Long Phillips Screw 25 17 101938 8 X 1 2 Long Phillips Screw 26 4 102071 Canopy Hoop Pole 27 1 102078 Short Roof Spreader Pole 28 6 102073 Straight Canopy Pole 29 2 102074 Bent Canopy Pole 30 1 102080 U Channel Molding 31 1 102081 Thermal X Base 32 1 102082 1 X 2 Rectangular Support Tube 33 2 102083 Rail Hanger Bracket 34 1 102137 Thermal X Tent Parts Diagram Canopy Pole Caps included in the assembly are available separately order p n 101826 canopy Hoop Sleeves included in the assembly are available separately order p n 101820 Step One 10 X 1 Long Philips Screw p n 101147 1 4 Thin Locknut p n 101082 1 1 2 X 1 3 4 Aluminum Angle X 9 Long p n 101146 Slide Block p n 101048 Seat Swivel Plate Assembly p n 101399 N 1 4 Dia X 1 2 Long Hex Head Screw p n 101470 Step Two 1 4 Dia X Long Hex Head Screw 1470 Step Three Cloth Accessory Hammock Pi shipped packed with Tent p p n 101466 1 4 Thin Locknut p n 101082 F
6. nopy Poles until the Spring Buttons engage the holes near the ends of each Canopy Hoop Pole e Support the First Canopy Hoop Pole as pictured with the Rear Adjustable Spreader Poles by inserting the Spreader Pole Tips into the predrilled holes of the Base and then clipping the opposite ends onto the First Canopy Hoop Pole e Rest the two remaining Canopy Hoop Poles against the now supported first Rear Adjustable Spreader Pole p n 101840 Canopy Hoop Poles p n 102071 First Canopy Hoop Pole Straight Canopy Poles Spreader Pole Tip 11 e Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles attaching the Roof Velcro as you go e Orient the remaining Canopy Hoop Pole so that the holes face upward and then feed the length of the pole through the three Porch Hoop Sleeves sewn on the Tent Next slide this Canopy Hoop Pole onto the Bent Canopy Poles engaging the Spring Buttons e Attach the Porch and Side Wall Velcro on each side of the Tent Remove the Rear Adjustable Spreader Poles now supporting the Canopy Hoop at the Link Door Wall to allow the tent to be set in the next step p Link Door Wall Rear Adjustable Spreader Pole Thermal X Tent p n 101840 p n 102137 Roof Velcro Side Wall Velcro 1 Porch Velcro Bent Canopy Pole p n 102074 Porch Hoop Sleeve Canopy Hoop Pole
7. ons with lights or reflectors to show drivers your whereabouts Night time exterior reflectors must be visible to reduce risk of collisions Warranty Clam Corporation Inc warrants to the original retail purchaser that all Clams are free from manufacturer s defects for one 1 year from the date of the original purchase Warranty does not cover cracked windows tent tears broken or bent hoops due to high wind weather conditions or unattended use Clam Corporation will replace or repair any part found defective within the one 1 year time limit All parts must be returned to Clam Corporation Inc Before returning any parts you must first call or write and acquire a return authorization All returns must be returned postage prepaid and include the original cash register receipt date and purchase price Note Please write the return authorization number on the outside of the package with the return article to help ensure the transaction gets processed swiftly and accurately Limitation of Liability It is expressly understood that Clam Corporation liability for its products whether due to breach of warranty negligence strict liability or otherwise is limited to the repair of the product as stated above Clam Corporation is not liable for any injury loss damage or expense whether direct or consequential including but not limited to loss of use income profit or damage to material arising in connection with the sale inst
8. p n 108305 Model No 8280 Specifications Height 75 23 packed Length 72 72 packed r d Depth 92 40 packed Extreme Warmer Weight 135 Ibs 2 SEE Clam Customer Service Information NOTICE Once used this shelter cannot be returned to the store If you have a Warranty Claim please contact Clam Corporation Customer Service by email inquiry or direct by calling Customer Service Hrs 8am to 4pm Mon Fri Central Standard Time Clam Corporation Inc Take a closer look 600 Clydesdale Trail Medina MN 55340 4 4 CORPORATION Phone 763 231 4120 Clam Corporation Inc Manual 102109 Fax 763 231 4121 Website www clamcorp com Email www customerservice clamcorp com Parts List Item Qtv p n Description 1 8 101048 Slide Block 2 18 101081 1 4 Flat Washer 3 34 101082 1 4 Thin Locknut 4 8 101083 1 4 Dia X 3 4 Long Phillips Screw 5 1 101095 Tow Rope 6 4 101146 1 1 2 X 1 3 4 Aluminum Angle X 9 Long 7 8 101147 10 X 1 Long Phillips Screw 8 2 101399 Seat Swivel Assembly 9 2 101420 Front Seat Bracket 10 2 101424 Rear Seat Bracket 11 8 101429 1 1 8 Dia Tube Cap 12 2 101430 1 x 2 Rectangular Tube Cap 13 2 101442 Latch Clip 14 1 101458 Center Console 15 2 101466 Cloth Accessory Ham
9. ptional but recommended accessory to help prolong the life of the unit Tow the unit out to your favorite fishing spot NOTE continuous pulling behind an ATV or snowmobile may result in premature wear of the base We recommend the optional Wear Strips be mounted to the base of your Fish Trap Make sure your Ice Shelter is completely dried out before storing for long periods of time Store your Ice Shelter in a cool dry place Keep away from rodents See our accessory catalog or www clamcorp com for these items and more Safety Instructions Please fully understand and follow all safety instructions as outlined Failure to do so could result in severe injury or death Do not use open flame heaters in your ice shelter Injury or death may result from fire if tent fabric is exposed to open flame The tent is not fireproof but the fabric is treated with a fire retardant that meets CPAI 84 specifications Application of any foreign substance may render the flame retardant properties ineffective Ice Armor fabric will melt when contact is made with hot surfaces i e heaters Death from asphyxiation may result from use of oxygen depleting heaters Open all vents for fresh air ventilation Never leave shelter unattended when set up Due to the increase in traffic snowmobiles autos etc on area lakes ice fishing can be hazardous at night If you choose to fish at night or in poor visibility conditions be sure to take precauti
10. ront Seat Bracket p n 101420 1 1 8 Dia Tube Cap p n 101429 1 4 Dia X 1 3 4 Long Phillips Screw p n 101486 1 1 8 Dia Tube p n 101652 Assembly from Step Four 1 4 Thin Locknut p n 101082 Latch Clip p n 101442 1 1 8 Dia Tube Cap p n 101429 Rear Seat Bracket p n 101424 1 4 Dia X 1 3 4 Long Phillips Screw p n 101486 _ 1 X 2 Rectangular Support Tube p n 102082 1 4 Dia X 1 3 4 Long Phillips Screw p n 101486 Note Slot Location Rail Hanger Bracket p n 102083 1 4 Dia x 3 4 A E les pe Al ee haare npr Kr SI inserted into Seat Rail Tube before installing m 101088 zT ffa mounting screw p n 101486 Canopy Bracket p n 101810 1 4 Dia x 3 4 Long Phillips Screw p n 101088 Thermal X Base p n 102081 ab Slot in Bracket is provided ab or designed to be used as an attachment point for l pS AP securing gear p n 101081 1 4 Thin Locknut p n 101082 Step Seven fa Notice All Buttons on the Straight Canopy Poles face towards the front of the unit d Sk B Straight Canopv Poles se ELL p n 102073 Kk 1 4 Dia X 2 1 2 Long ae L Phillips Screw 1 4 Flat Washer p n 101906 p n 101081 d 1 4 Thin Locknut CHD p n 101082 A IHN x Bent Canopy Pole p n 102074 id 10 e Slide three Canopy Hoop Poles onto the mounted Straight Ca
Download Pdf Manuals
Related Search