Citizen Systems CD-S500 Series User's Manual
Contents
1. EE R EA 44 Interface COMPLIANCE STATEMENT FOR EUROPEAN USERS CE marking shows conformity to the following criteria and provisions Low Voltage Directive 73 23 EEC EN60950 EMC Directive 89 336 EEC EN55022 EN55024 EN61000 3 2 amp EN61000 3 3 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense EMI COMPLIANCE STATEMENT FOR CANADIAN USERS This Class A digital apparatus complies with Canadian ICES 003 This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception This digital apparatus does not exceed the Class A limits for radio noise emissions from digital ap2. after removing the rewinder shaft install the copy roll paper and pull the end of the roll paper straight towards ys Rewinder shaft LS 2P or 3P copy roll paper a gt 2 About 30cm Roll paper that is gently pulled taut you for about 30cm as shown in the figure Hold the center of the roll paper to pull it as straight as possible so that one of the sides of the paper does not slacken 5 Maintaining light tension in the copy roll paper firmly close the platen unit until you hear a click A Caution Be very careful not to let a s your hands touch the blade Plater wait on the paper cutter bar Be careful of the paper cut bar 6 set one side of the copy roll paper Copy roll paper copy side on the rewinder shaft as copy side shown in the figure and tightly wind 4 it about 2 rotations in the direction shown by the arrow Check to make sure that the copy roll b paper rotates with the rewinder shaft K Rewinder shaft Protrudes about 5cm Wind it about twice 31 s uLiq oy Suueds1q Ha elil xili Preparing the Printer Installing roll paper grooves on both sides 7 Being careful not to let the copy roll paper set on the rewinder shaft slacken place the roll paper in the Turn the flange on the rewinder shaft in the direction shown by the arrow and make sure that the copy roll paper rotates vvith the revvinder
3. Until completion of initial settings when the power is turned on 2 During Self Print Printer RESET 1ms or more is higher E Buffer Full Control E Connection with HOST Reception buffer 40 4K Printer Host gt FG FG TXD 1 1 2 TXD 5 2 3 RXD 3 RXD 4 RTS 7 4 RTS 5 CTS 8 1536 bytes 16 512 bytes 7 XON XOFF oe Buffer size 16 512 7 C m verrun Buffer size ytes 20 DTR 20 DTR XOFF cancel size 8 1536 bytes an 48 Parallel IEEE1284 Interface E Pin assignment Function Direction Compatibility Mode Nibble Mode Byte Mode nput Strobe HostCLK HostCLK Input Output Data0 Data0 Data0 nput Output Data1 Datal Datal Input Output Data2 Data2 Data2 Input Output Data3 Data3 Data3 Input Output Data4 Data4 Data4 Input Output Data5 Data5 Data5 Input Output Data6 Data6 Data6 WOlLOINID mM ARIWIN Input Output Data7 Data7 Data7 Output ACK PtrCLK PtrCLK Output BUSY PtrBUSY Data3 7 PtrBUSY Output PE AckDataReq Data2 6 AckDataReq Output SELECT Xflag Datal 5 Xflag Input AutoFeed HostBUSY HostBUSY NC ND ND GND GND GND FG FG FG Logic H Logic H Logic
4. 76 2 0 7mm 341 36 inch 69 5 0 6mm 3 1 36 inch 57 5 0 5mm 2 26 0 02inch Roll diameter 630mm to 083mm Core diameter Interior diameter 1 75 mm exterior diameter 627mm or less Paper thickness 0 06 to 0 085mm Weight 52 3 to 64 0 g m JIS P8124 Recommended paper 45 to 55kg 1 000 sheets 7 88mm x 1 091mm Register paper Oji Paper Co Ltd or equivalent Pressure sensitive paper Non carbon 2P 3P paper 1 original 1 2 copies Paper width Roll diameter Core diameter Paper thickness Recommended paper 76 2 0 7mm 341 36 inch 69 5 0 6mm 341 36 inch 57 5 0 5mm 2 26 0 02 inch 630mm to b83mm Interior diameter 01075 mm exterior diameter 627mm or less 0 05 to 0 20mm But the total thickness that can be cut is from 0 05 to 0 14mm 2P NCR Super Mitsubishi Paper Mills Limited prints in blue or equivalent Cautions concerning the roll paper Starting to wind the roll paper interior end processing with center core It must not be folded and its internal diameter must be even It must not be rolled back There must be no glue on its center core It must be wound with its printing side facing outwards When it is 2P paper there must be no glue between the top and bottom sheets In the case of 3P paper there must be no glue on the top middle or bottom papers Use pressure sensitive paper with total thickness no greater than 0 20mm and remember that the print
5. Soft SVV Setting Mode PAPER POWER OUT ERROR FEED sig 1 Q AREA Reopening and closing the front cover Flashing gt Lit 35 PpOVV aueuaquiep M Ete Maintenance Mode Soft SW Setting Mode Operating method Press the FEED switch less than 2 seconds The setting changes The present set value is changed and the same item is reprinted Press the FEED switch and when the buzzer sounds once release it Pressing the FEED switch continuously 2 seconds or more Moves to the next item It prints the present set value of the next item Press the FEED switch and when the buzzer sounds three times release it Opening closing the front cover After saving the set values it reprints all items from the top and returns to normal power on status If the power is turned off without opening and closing the front cover the setting change is invalid If the paper runs out during the change set the paper and close the rear cover to continue the process lt Soft Switch Setting gt Press Feed Change PARM Press Feed For 2S Next Item F Cover Open Close Save 8 Exit Soft Control SW gt Command Type EPSON Number of Col 40 33 Font Select 7x9 Paper Plies OFF Paper End ENB Paper Near End ENB Slashed Zero OFF Print Direct BI DIR Auto LF OFF Code Page 437 Buffer Size 4K Init Si
6. When lightening is striking nearby remove the plug of the power cord from the outlet Lightening will cause fire or electric shock 6 Do not place the power cord near a heating device The cover of the power cord will melt causing fire or electric shock 6 When the printer will not be used for a long period be sure to remove the plug of the power cord from the outlet to guarantee safety Isolate the AC power source from other devices that generate noise AC adapter cable Flat side of the cable is up AC adapter type AC inlet Built in AC adapter type Installation This printer can be installed horizontally or vertically and can be wall mounted But according to the model you are using there may be restrictions on how it is installed Refer to the following table Horizontal Vertical Wall Mount Standard model AC adapter type Standard model Built in AC adapter type Auto cutter equipped model AC adapter type Auto cutter equipped model Built in AC adapter type Auto cutter and rewinder equipped model AC adapter type Auto cutter and rewinder equipped model Built in AC adapter type 1 Accessory rubber feet must be used to prevent slipping 2 The optional specialized wall hanging unit is necessary to hang it on the wall Horizontal Vertical and wall mounted ee 2 gt J9 ULg
7. according to its usage environment in maintenance mode And it is also possible to change their settings back to the initial factory shipping setting or to adjust the cut position after printing in this mode And the content of the settings can be confirmed in demonstration printing mode To change the settings in maintenance mode print and check the present settings Demonstration printing mode Setting the mode Turning the power on while pressing the FEED switch with the front cover and the rear cover both closed starts demonstration printing mode and the demonstration printing and the present printing settings are printed Setting maintenance mode 1 Set maintenance mode by turning on F ront cover open the power while pressing the FEED m svvitch vvith the front cover open and 3 a the rear cover closed then releasing BS 6 the FEED switch FEED switch 2 The POWER LED flashes as the printer enters maintenance mode Power switch Close the front cover in this status PAPER N POWER PAPER ERROR FEED sis 1 Flashing Types of maintenance mode There are the following four types of maintenance mode Each mode is selected according to the number of times the FEED switch is pressed from maintenance mode HEX Dump Mode Press the FEED switch O times and reopen and close the front cover 6 Soft SW Setting Mode Press the FEED switch 1 time and reopen and close
8. and close the cover to ERROR off return the printer online Paper near end POWER lit When the PAPER NEAR END on the Soft SW is PAPER OUT enabled printing stops and the printer goes online ERROR When it is disabled the lamp flashes and printing continues to PAPER END Rear front cover POWER Lit During printing printing is immediately stopped and open PAPER OUT Depends on status the printer goes offline Close the cover to restore the ERROR Lit printer to online status Head hot POWER Lit Cooling starts After the temperature has fallen it is PAPER OUT Depends on status automatically restored and printing restarts ERROR The buzzer continues to sound until the error is cancelled by the FEED switch HP abnormal POWER OO The printer goes offline Remove the paper jam or PAPER OUT O066 other problem and press the FEED switch to restore ERROR the printer to online status The buzzer continues to sound until the error is Black mark POWER 0066 hram PAPER OUT 00 cancelled by the FEED switch ERROR 0000 Cutter abnormal POWER position detection PAPER OUT ERROR 00 Hardware abnormal POWER Off Turn off the power then turn it on again If the error RAM read write PAPER OUT 60060 continues after cutting the power off notify the ERROR 6060 dealer where you purchased the printer or service Hardware abnormal POWER Off personnel FROM read writ
9. and the back or bottom are provided for ventilation To ensure reliable operation of the product and to protect it from overheating do not block or cover these openings The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventilation is provided This product should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company This product is equipped with a three pronged plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug Do not allow anything to rest on the power cord Do not locate this product where the cord will be walked on If an extension cord is used with this product make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord ampere rating Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes for 120V outlet and 75 amperes for 220V 240V outlet Never push objects o
10. equippe E Built in AC adapter type models T Operation panel _ see page 18 D Paper check window t can be used to check the amount of paper left on the roll 2 Rear cover t can be opened to set or to replace a ors Rear connect paper roll see page 19 3 Rear cover open lever It is a lever used to open the rear cover Pull the lever towards you to open the rear cover Auto cutter and rewinder equipped model Front cover It can be opened to set or replace the ribbon cassette 5 Power switch It turns the printer power on and off Cutter lock clearing screw hole When the rear cover cannot be opened because the blade of the auto cutter protrudes after a malfunction or as a result of a paper jam turn this screw with a Phillips head screw driver to return the 1 blade Operation panel see page 18 Rear connectors AC adapter case see page 19 This is installed only for the built in AC adapter type 16 m nterior AC adapter type Standard and auto cutter equipped model 8 Auto cutter and rewinder equipped model D Platen unit In the standard and auto cutter equipped models it is combined with 8 the auto cutter Paper cut bar It is used to cut the paper manually 3 Platen open lever It is a lever used to open the platen unit on the rewinder equipped model Open the platen unit by pulling it towards you Print
11. head cover 5 Ribbon cassette drive shaft Print head Rewinder shaft It rewinds the copy side of the copy roll paper Auto cutter unit It automatically cuts the paper after printing is completed The cut action is set by a command in Soft SW Setting Mode S34Ed JO sUOI IUNY pue soweN ia ETAT Names and Functions of Parts Operation Panel PAPER POVVER OUT ERROR FEED 4 D POVVER LED Green 4 FEED Svvitch t is lit when the power is supplied When When this switch is pressed once paper maintenance mode is set or there is an feeds 1 line If it is held down paper error indication it is either lit or flashing feeds continuously until it is released And when there is a printer error pressing 2I PAPER OUT LED Orange this switch can cancel the error status It is lit in paper out status When maintenance mode is set or there is an error indication it is either lit or flashing ERROR LED Orange It is lit when the rear cover or front cover is open When maintenance mode is set or there is an error indication it is either lit or flashing 18 Rear Connectors AC adapter type Parallel IEEE1284 interface Serial RS232C interface ES ll Built in AC adapter type o Interface connector It is connected to either a serial RS232C or parallel IEEE1284 int
12. npo nu m 11 11 Introduction Explanation of models Examples of models E Standard model AC Adapter type H Standard model Built in AC adapter type m gt CD S500A000 00 00 CD S500SO000 00 00 E Auto cutter equipped model E Auto cutter equipped model AC Adapter type Built in AC adapter type CD S501A000 00 00 CD S501S000 00 00 E Auto cutter and rewinder equipped E Auto cutter and rewinder equipped model AC Adapter type model Built in AC adapter type CD S503A000 00 00 CD S503S000 00 00 1 4 5 55 5 Checking the Accessories Check to make sure that the following accessories are included with your printer Printer 1 6 Partition 1 AC adapter 1 6 Slip prevention rubber feet 4 CD S500A series only Not on the auto cutter and rewinder equipped model 6 Pover cord 1 Sample roll paper 1 Ribbon cassette 1 User s Manual this document E Printer 1 AC adapter type Built in AC adapter type The AC adapter is set inside the AC adapter case 6 Power cord 6 Ribbon cassette 6 AC adapter 6 Partition Sample roll paper User Manual this document uon npo nul mi 15 Names and Functions of Parts Names and Functions of Parts Exterior E AC adapter type d and ipped Standard and auto cutter
13. oy Suueds1q elil kli Preparing the Printer Setting the Paper Near End Sensor Change the sensor location according to the way the printer is installed and the interior diameter of the roll paper you are using Referring to the following table set it at a location suited to the usage environment by moving it to the left and right while pushing the concave part of the center of the sensor with your finger When shipped from the factory it is set at 624mm Paper near end sensor When installed vertically and 5 wall hung 3 21 VVhen installed horizontally Installation Remaining roll method paper mm Sensor location Approx 022 1 Horizontal Approx 024 2 Approx 027 3 Approx 027 4 Vertical A 024 wall hung Hu 5 Approx 022 6 A Caution 6 The remaining roll paper external diameter of the roll paper differs greatly according to the type of roll paper used Use these values only as guidelines When the sensor has detected the remaining roll paper during printing the printer stops printing after it has printed all the data that it had received If you are using a model with parallel IEEE1284 interface specifications you can select sensor enabled disabled in Soft SW Setting Mode If you are using a model with serial RS232C interface specifications it is always enabled 24 m Setti
14. removing the jammed paper be careful not to touch the area around the print head nor the cutter blade If you do you will be burned or cut 42 Trouble Shooting When there is trouble with this printer take action to clear up the trouble according to the following table If this action does not clear up the trouble notify the dealer where you purchased the printer or service personnel Symptom Check Action Paper jam Check for a jam at the paper ejection opening If you cannot open the rear cover do check number 2 Remove all the jammed paper Remove the roll paper from the printer and put it back again Rear cover does not open Check to see if the blade of the auto cutter is protruding Insert a Phillips screwdriver into the cutter lock cancel use feed hole on the printer and turn it clockwise or counter clockwise Use a 1 screwdriver Rotate the screwdriver while watching the paper ejection opening and stop turning it when both ends of the blade are fully retracted P 42 A Caution Do not try to force the rear cover to open If you do the printer vill be damaged and you will be cut by the blade Ribbon does not feed correctly Turn the knob on the ribbon cassette After turning the knob until the ribbon feeds smoothly reset the ribbon cassette If you cannot turn the knob the ribbon may be jammed inside the cassette If the sit
15. shaft Taking up slack while checking that the copy roll paper winds you hear a click at the print start position N Caution Be very careful not to let the rear cover catch your hands when closing the rear cover 8 with the other side of the copy roll paper original side pulled lightly taut close the rear cover firmly until Hold the center of the roll paper to pull it as straight as possible so that one of the sides of the paper does not slacken Paper feeds automatically and stops 7 Rear cover K2 Roll paper that is gently pulled taut D pulling it towards you N Caution Do not insert any foreign objects such as a paper clip into the cutter unit 32 off surplus paper by holding one side of the end of the roll paper and Operation when the cover is opened and closed Operation when the front cover is opened and closed Opening During printing the printing stops and if it is in red printing status the ribbon is switched to the black ribbon status moves to the centering location and becomes the condition you can replace the ribbon cassette Closing If it was red printing status when it was opened the ribbon returns to red status and if there is printing data printing restarts Operation when the rear cover is opened and closed Opening During printing the printing stops and the ribbon moves to the ce
16. specified Do not put anything on the power cord or step on it Do not drag or carry the printer with the power cord or interface cable Avoid plugging the power cord into an outlet with many loads Do not bundle the power cord when inserting the plug Always grip the plug housing not the cord to plug unplug the power cord Make certain the power is turned off before connecting disconnecting the interface cable Avoid lengthening the signal cable or connecting it to any noise producing device If it is unavoidable use the shielded cable or twisted pair for each signal Place the printer near the outlet where the power cord can be unplugged easily to shut off power Use the AC outlet that accepts a three pronged plug Otherwise static electricity may be generated and there will be danger of electric shock Do not carry it holding the cover Doing this might break its mechanisms or cause it to malfunction ETC Introduction Thank you very much for purchasing the Citizen Dot Matrix Printer CD S500 series This printer is a dot matrix printer developed for use with various kinds of data communication terminals POS terminals and kitchen printers It can be used for a wide range of applications thanks to its rich selection of functions Features Compact design A paper drop in mechanism that simplifies paper loading High speed printing to a maximum of 240cps Multiple copy printing original form 2 copi
17. the front cover Initial Factory Shipping Mode Press the FEED switch 2 times and reopen and close the front cover 6 Cut Position Adjustment Mode Press the FEED switch 3 times and reopen and close the front cover 3 4 ee HEX Dump Mode Setting the mode If the front cover is reopened and closed in maintenance mode POVVER LED is flashing the POVVER LED stops flashing and remains lit and the printer enters HEX Dump Mode After printing the title it stands by to receive data To leave HEX Dump Mode turn off the printer power then turn the power on again with the front and rear covers both closed Soft SW Setting Mode Setting the mode 1 If the FEED switch is pressed once in maintenance mode POWER LED is flashing the POWER LED and PAPER OUT LED start flashing PAPER RSS RSS ERROR FEED OR and closing the front cover Flashing Lit lt HEX DUMP PRINT gt XX XX XX XX XX XX XX XX ikkkkkkk XX XX XX XX XX XX kkkkkkk XX XX XX XX XX XX XX XX XX XX XX XX XX aks k k k k k k k k PAPER POVVER OUT ERROR FEED A Flashing Press once 2 the front cover is reopened and closed in this status the POVVER LED and PAPER OUT LED stop flashing to and remain lit and after the title and top items have printed it enters
18. vision Le present appareil num rique n emet pas de bruite radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Cet quipment est con u pour fournir une protection satisfaisante contre de telles interferences dans une installation r sidentielle Cependant il n y a pas de garantie contre les interf rences avec les r ceptions radio ou t l vision provoqu es par la mise en et hors circuit de l quipment aussi il est demand a l utilisateur d essayer de corriger l interf rence par l une ou plus des mesures suivantes R orienter l antenne de r ception Installer l ordinateur autre part par gard pour le r cepteur Brancher l ordinateur dans une prise de courant diff rente de fa on ce que l ordinateur et le r cepteur soient branch s sur des circuits diff rents mportant Safety nstructions Read all of these instructions and save them for later reference Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings on the cabinet
19. DOT MATRIX PRINTER CD S500 series ae User s Manual CITIZEN Table of Contents COMPLIANCE STATEMENT FOR EUROPEAN USERS 5 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS 25 5 EMI COMPLIANCE STATEMENT FOR CANADIAN USERS 4 ETAT DE CONFORMITE EMI A LUSAGE DES UTILISATEURS CANADIENS Important Safety Ins MUCUS sand une Bazas 6 NOTICE sn 00 7 SAFETY INSTRUCTIONS which must be strictry 1 6 8 Chapter1 Introduction Feat resi l aa aad 12 Explanation of the Models 13 Checking the Accessories onanirao 15 Chapter2 Names and Functions of Parts 2507000600 teen ten es 16 Chapter3 Preparing the Printer Gonnectonsu den nr ini 20 Installatioun E ES 23 Setting the Paper Near End Sensor us 24 Setting the Paper Width and Printing Line Column Number 25 Installing the Ribbon Cassette ns 27 nstall hz Roll Paper sesser 28 Operation when the cover is opened and 1 33 Chapter4 Maintenance Mode HEX Dump Modes eue 35 Soft SW Setting Mode rio 35 Initial Factory Shipping Mode cesssssesssessseessseesseessseesseessseesseessseesseesssenees 39 Cut Position Adjustment Mode sissien 40 Enor INdiCAtOrS aa aaa s b l n n 41 lrouble Sheeting can sas dents 43 Chapter5 Appendixes
20. H GND GND GND INIT INIT INIT FAULT DataAvail DataO 4 DataAvail GND ND ND DK_STATUS ND ND 5V ND ND Select in BUSY 1284 Active 1284 Active Active Low 15 B MIN Tus C MIN 15 MAX 1us E APPOROX 3 211s APPOROX 3 21s s xipu ddy SENTE Appendixes Parallel IEEE1284 Interface E Timing when power is on E INIT signal timing A A More than 16us FAULT Drawer Kick Out Interface E Pin assignment Direction Function Frame GND Output Drawer Kick out Signal 1 Inout Drawer Open Close 24V Output Drawer Kick out Signal 2 Signal GND The ESC pm t1 t2 commands select either Drawer Kick out Signal 1 or 2 to set the pulse time v T2 x 2ms V hen ON When OFF Note e T2 when OFF gt T1 when ON CH is satisfied e The maximum amperage at 24V is up to 1A When connected to one that exceeds 1A the printer and connected equipment may be damaged 50 dapan CBM Corporation CBM Bldg 5 68 10 Nakano Nakano ku Tokyo 164 0001 Tel 81 3 5345 7540 Fax 81 3 5345 7541 NJ74902 00 Printed in China
21. Width of 57 5mm Space between Line Columns Font Select characters When Line Columns 42 35 are selected 346 dots Printing line columns 346 dots t Paper feed direction Full columns 9x9 dots 3 dots 25 columns 40 33 7x9 dots 3 dots 30 columns 300 dots 9x9 dots 2 dots 26 columns 42133 7x9 dots 2 dots 31 columns 286 dots Paper width 76 2mm Paper width 57 5mm y When Line Columns 40 33 are selected 300 dots When Line Columns 42 35 are Paper feed direction selected 286 dots x Right offset 100 dots 26 Installing the Ribbon Cassette Front cover 1 Open the front cover of the printer Insert your fingers into the dents at opposite ends of the front cover to open it with both hands 2 Turn the ribbon cassette knob in the direction shown by the arrow to fully stretch the ribbon S insert the cassette into the printer Paper cut bar until a click is heard so that the ribbon Print head cover is between the paper cut bar and the y print head cover f it difficult to insert turn the ribbon cassette knob again 4 Close the front cover A Caution Be very careful not to let your hands touch the print head cover when replacing the ribbon cassette When the print head has become heated there is a danger of AN it burning your hand 27 d ul
22. ce cable Connecting the Dravver Match the top and bottom of the dravver kick connector vvith the cable terminal and insert it firmly until you hear a click Dravver kick cable 6 Connect only a specialized drawer Do not connect a telephone line 6 Output is impossible during printing 6 Drawer 1 and drawer 2 cannot be driven simultaneously 6 Use a drawer use solenoid that is at least 24O Make sure that the output current is not higher than 1A This may cause a malfunction or burn damage 6 Install the drawer kick cable so that it will not be caught on your shoes etc See page 48 for detailed specifications of the interfaces en 2 J9 ULg ou Suueds1q R EE Preparing the Printer 22 Connecting the Povver 1 Make sure that the printer power switch is set to OFF 2 If your printer is an AC adapter type insert the AC adapter cable connector with its flat side upwards into the power connector on the rear surface of the printer If your printer is a built in AC adapter type insert the plug on the power cord into the AC inlet on the back surface of the printer A Caution Do not use an adapter other than the stipulated product Model 51AD Always hold the connector when inserting or removing the cable connector of the AC adapter Stretching the power cord by pulling it will damage it causing fire electric shocks or a break in the conductor
23. e PAPER OUT ERROR 060060 24V abnormal POWER Off PAPER OUT Off ERROR 060060 e There are no RS232C communication error or front cover opened closed detection indicators If the buzzer setting is OFF in Soft SW Setting Mode the buzzer does not sound O Lit Off _ 5 u 2POW eueuazuley EMAC Maintenance Mode Clearing a Paper Jam Clearing method 1 Turn off the power and open the rear rece End of the blade of the cutter If the rear cover cannot be opened When there is a cutter problem the printer may stop with the cutter blade 5 protruding so that pressing the FEED switch fails to clear the error When this happens restore the cutter blade manually by inserting a screwdriver into Front cover the hole on the left side surface of the rear cover and rotating it then open Paper cut bar the cover the blade will be restored whether you turn it to the left or right Turn the screw driver so that the projections on both ends of the blade of the cutter are returned to the back of the printer direction shown by the arrow 2 Rem v all the jammed paper temporarily remove the roll paper that is installed in the printer 3 Close the rear cover and turn on the Cutter lock clearing screw hole power The auto cutter operation will be initialized and the error cleared N Caution When
24. e power cord into an outlet with many loads Do not spill drinks such as tea coffee and juice on the printer or spray insecticide on the printer If drink or water is spilled first be sure to turn the power off and remove the power cord from the outlet then consult our service personnel Do not disassemble or modify the printer Do not use this printer when any safety switch built into the product has been cancelled without solving the problem that activated it If you do there is a danger that the printer will malfunction injuring burning or electrocuting you Discard or safely store the plastic packing bag This bag should be kept away from children If the bag is pulled over a child s head it may cause suffocation General Precautions Prior to operation read the safety instructions carefully and observe them Do not drop or put foreign matter such as clips and pins into the printer This may cause problems Be careful when moving or carrying the printer Dropping the printer may cause injury or property damage If this printer is accidentally dropped be sure to notify a service person do not try to repair it yourself Do not open the printer during printing When cleaning the surface of the printer case do not use the cloth that is soaked in thinner trichloroethylene benzine ketone or similar chemicals Do not use the printer where there is a lot of oil iron particles or dust Do not spill liquids or spray insect
25. efore use be sure to read this manual And keep it handy for reference when needed e The contents of this manual may change without prior notice e Reproduction transfer or transmission of the contents of this manual without prior consent is strictly prohibited e We are not liable for any damage resulting from the use of the information contained herein regardless of errors omissions or misprints e We are not liable for any problems resulting from the use of optional products and consumable supplies other than the designated products contained herein e Do not handle disassemble or repair the parts other than those specified in this manual e We are not liable for any damage caused by user s erroneous use of the printer and inadequate environment e Data residing in the printer is temporary Therefore all data will be lost if power is lost We are not liable for any damage or loss of profits caused by data loss due to failures repairs inspections etc e Please contact us if there are any mistakes or ambiguities within this manual If there are missing or incorrectly collated pages in this manual contact us to obtain a new manual EE 7 SAFETY INSTRUCTIONS which must be strictly observed e To prevent personal injury or property damage the following shall be strictly observed e The degree of possible injury and damage due to incorrect use or improperly following instructions is described below Indicates a sit
26. er will not cut paper with total thickness greater than 0 14mm If you use pressure sensitive paper with total thickness greater than 0 14mm either do not use the cutter or else rewind the bottom paper with the rewinder to reduce the total thickness top paper middle paper to 0 14mm or less s xipu ddy b l muuuuu KNZ ZZZ RZA ZNUuUUuSNRBRS SNNRUNNN 4 7 1 1 Appendixes Interface Serial RS232C interface E Pin assignment Signal Name Direction Function GF Frame ground TXD Output Data transmission RXD Input Data reception RTS Output Same as DTR 20pin DSR Input Host reception enabled status HIGH READY LOW NOT READY During DTR RTS control The printer transmits data after it is confirmed that DSR is high But transmission by DLE EOT GS a During XON XOFF control Printer does not confirm DSR Signal ground Printer READY BUSY status HIGH READY LOW BUSY During DTR RTS control When the printer is in reception enabled status it is READY when it is reception disabled it is BUSY Printer status 1 BUSY until completion of initial settings when the power is turned on 2 BUSY in normal OFFLINE status 3 BUSY in OFFLINE status during PE 4 BUSY in OFFLINE status when other errors occur 5 BUSY when the reception buffer is full 6 BUSY during Self Print During XON XOFF control Always HIGH READY except under the following conditions 1
27. erface cable A USB interface replaced by a serial or parallel interface will be available as a factory option Hk s ieg JO suOI UNY pue s ulN iyi 2 Dravver kick connector t is connected to a cable from the drawer 3 Power source connector t is connected to a cable from the AC adapter 4 Povver source inlet t is connected to the power cord Others Built in Buzzer A buzzer sounds when the FEED switch is operated and when there is an error The buzzer can be switched between enabled and disabled in Soft SW setting mode User Memory Logo data or text data prepared by the user can be stored in memory This stored data remains in memory even after the power is turned off ee 1 9 elil kili Preparing the Printer 20 Connections Connecting the Interface Cable Turn off the power to the printer and insert the connectors being careful about their orientation A Caution 6 Always hold the connector when pulling out a cable 6 Install the interface cable so that it will not be caught on your shoes etc Connecting the serial RS232C interface cable Make sure that you insert it firmly and fix it in place by tightening the screw Serial RS232C interface cable E Connecting the parallel IEEE 1284 interface cable Make sure that you insert it firmly and fix it in place by turning the attachment screws in the direction shown by the arrow Parallel IEEE1284 interfa
28. es Input buffer available 6 Black mark sensor mechanism Versatile printing layout using the page mode Logo data or text data prepared by the user can be stored in its user memory Built in drawer kick out interface Optional auto cutter full cut partial cut Capacity for paper with widths of 76 2 69 5 57 5mm Serial RS 232C or Parallel IEEE and Centronics compliant interface is available as a factory option Selection of functions diversified by its operation panel Soft SW setting mode 6 Can be wall mounted optional 6 Built in buzzer Built in or external AC adapter types available Two color printing red black 12 R Z Zu Explanation of the Models Models in this series are identified by the following model naming method Model Number CD SL L L O 000 00 00 Model name 500 Standard model 501 Built in auto cutter model 503 Built in auto cutter and revvinder model Povver source type A AC adapter type S Built in AC adapter type nterface PA Parallel IEEE1284 compatible RS Serial RS 232C compatible UB USB Region Characters power cord J Japan E Europe U North America Case Color WH Cool white BK Black Black mark sensor None No sensor M1 Left sensor for paper front M2 Right sensor for paper back M3 Left sensor for paper front M4 Right sensor for paper back uon
29. f any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product Except as explained elsewhere in this manual don t attempt to service this product yourself Opening and removing those covers that are marked Do Not Remove may expose you to dangerous voltage points or other risks Refer all servicing on those compartments to service personnel e The main plug on this equipment must be used to disconnect mains power Please ensure that the socket outlet is installed near the equipment and shall be easily accessible e Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power cord or plug is damaged or frayed B If liquid has been spilled into the product C If the product has been exposed to rain or water D If the product does not operate normally when the operating instructions are followed Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet has been damaged F If the product exhibits a distinct change in performance indicating a need for service Notice e B
30. g Press 3 times 2 Reopening and closing the front cover in this status switches the POWER LED and the ERROR LED from flashing to continuously lit status and enters Cut Position Adjustment Mode Sa Reopening and closing the front cover Flashing Lit Operating Method Pressing the FEED switch less than 2 Cutter Amendment 000 seconds The present value is changed in units of t 1 144 Cut position Paper feed direction Opening and closing the front cover The of the adjustment direction changes Immediately after entering adjustment mode the value is changed in the direction Opening then closing the front cover changes the of the adjusted value Pressing and holding the FEED Switch 2 seconds or more The present value is saved and the printer enters normal power on status Adjustment range 999 to 999 Initial value 000 407 oo Error ndicators When this printer malfunctions or jams etc the type of problem is indicated by a buzzer and by lit or flashing LED on the operating panel In error status the error indication can be cancelled by pressing the FEED switch Error indicator table Type of Error LED indicator Operation and restoration method Paper end POWER Lit During printing printing stops and the printer goes PAPER OUT Lit offline Replace the paper
31. gnal ENB Buzzer ON lt lInterface SW gt Baud Rate 19200 Data Length 8bit Parity Bit NONE Stop Bit 1bit Protocol DTR lt Mechanical SW gt Paper Width 76 2 Auto Cutter FREE Color Ribbon ON Take Up Device ON Command Type EPSON Operations Press the gt FEED Switch Command Type STAR Press and hold the FEED Switch Number of Col 40 33 Press and hold the FEED Switch Font Select 7x9 Press the i FEED Switch Font Select 9x9 Example of a change of the Command Type to STAR and the Font Select to 909 36 EZ Setting Mode Table E Soft Control SW Set item Initial value Setting value Remarks Command Type EPSON EPSON The emulation is selected from EPSON STAR STAR CBM1 CBM2 CBM1 CBM2 Number of Col 40 33 40 33 Number of full dot in full column is 200 dots For the 42 35 number of line columns based on the paper width see Setting the Paper Width and Printing Line Column Number Font Select 7x9 7x9 The initial font size is selected immediately after the 9x9 power is turned on Paper Plies OFF OFF Copy mode is selected 2P OFF 2P 3P can be selected But when 3P is set the 3P printing speed is lovv Paper End ENB ENB The PE signal enabled disabled is set at paper end when DIS only the centro interface is set as enabled During enabled status BUSY PE FAULT are output and printing st
32. hen an abnormality occurs as OFF enabled ON disabled OFF E Interface SW Displayed only when the serial board is mounted Set item Initial value Setting value Remarks Baud Rate 19200 19200 Sets the baud rate of the serial interface 9600 4800 2400 1200 Data Length 8 bit 8 bit Sets the character length of the serial interface 7 bit Parity Bit NONE NONE Sets the communication parity of the serial interface EVEN ODD Stop Bit 1 bit 1 bit Sets the stop bit of the serial interface 2 bit Protocol DTR DTR X ON OFF Mechanical SW Set item nitial value Setting value Remarks Paper Width 76 2 76 2 Selects the paper size 69 5 57 5 Auto Cutter FREE OFF Selects the cutter operation FREE When it is OFF the FULL PAR commands do not start FULL cutting PAR In FREE status cutting is done according to the FULL PAR commands In FULL status full cut is always done by both the FULL PAR commands In PAR status partial cutting is always done by both the FULL PAR commands 3 8 HEK NN X IQRNIN Set item Initial value Setting value Remarks Color Ribbon ON ON Selects the color function OFF During OFF the change color command is ignored Take Up Device ON ON Selects the rewinder function During OFF the rewinder motor does not operate Concerning Mechanical SW operation Functions that are not supported by the specifications at time of shipping have no im
33. icide on the printer Do not jolt or impact to the printer by stepping on dropping or hitting the printer Operate the control panel properly A careless rough handling may cause problems or malfunction Do not use such sharp edged tool as a ballpoint pen for operation Be careful of the edges of the plates so injury or property damage is possible If a problem occurs during printing stop the printer immediately and unplug the power cord from the outlet When printer trouble occurs do not try to dissemble it Instead consult our service personnel SO ZN NZHZNMNMNRZRZ Z IN NI Precautions When Installing the Printer Prior to operation read the safety instructions carefully and observe them Do not use or store the printer near fire excessive moisture in direct sunlight near an air conditioner or heater or other source of unusually humidity or excessive dust Do not place the printer where chemical reactions occur such as in a laboratory Do not place the printer where air is mixed with salt or gas The printer must sit on a firm level surface where there is ample ventilation Never allow the printer s air vent to be blocked by an object Do not put anything on the top of printer Do not place the printer near a radio or television and do not use the same wall outlet for the printer and radio or television Radio or television reception could be adversely affected Do not use a power voltage or frequency other than those
34. iq 24 Suueds1q i Preparing the Printer Installing Roll Paper The following are the types of roll paper that can be used by this printer Types 1P roll paper 2P copy roll paper 1 original 1 copy 3P copy roll paper 1 original 2 copies 2P and 3P copy roll paper are only usable on models equipped with auto cutter and rewinder Paper widths 76 2 0 7 69 5 0 6 57 5 0 5 mm Roll diameter 630mm to 683mm Core diameter Interior diameter 6 1076 mm exterior diameter 27mm or less Paper thickness 1P 0 06 to 0 085mm Copy paper 0 05 to 0 20mm total thickness But the total thickness that can be cut is from 0 05 to 0 14mm Standard and Auto Cutter Equipped Models Installation method Rear cover open lever 1 Pull the rear cover open lever tovvards you to open the rear cover 2 set the attached partition in place if s r Partition the roll paper you are using is 69 5mm 4 wide or 57 5mm wide Change the paper width by changing the value set as the width using the Soft SW Setting Mode See page 35 A Caution When setting the roll paper be careful not to cut your v hand on the edge of the paper Location set for width of 69 5mm 28 3 Place the roll paper and pull the end of the roll paper directly tovvards you as shown in the figure Hold the center of the roll paper to pull it as straight as pos
35. ng the Paper Width and Printing Line Column Number The printing dot line columns are changed as follows by setting the Paper Width of the roll paper used the Line Columns and the Font Select in Soft SW Setting Mode For details about setting see Soft SW Setting Mode page 35 When setting Paper Width of 76 2mm Soft SW Setting Mode Space between Printing line Full columns Line Columns Font Select characters columns 9x9 dots 3 dots 33 columns 40733 7x9 dots 3 dots 40 columns 9x9 dots 2 dots 35 columns Fe 7x9 dots 2 dots 42 columns Paper width 76 2mm When Line Columns 40 33 are selected 400 dots 1 Paper feed When Line Columns 42 35 are selected 386 dots direction EE 25 d ou Sunedo1q elil kili Preparing the Printer Soft SVV Setting Mode When setting Paper Width of 69 5mm Space between Font Select Line Columns characters Setting Paper VVidth and Printing Line Columns Printing line columns Full columns 9x9 dots 3 dots 30 columns 2 7x9 dots 3 dots 36 columns 360 dots 9x9 dots 2 dots 31 columns 42 35 7x9 dots 2 dots Paper width 76 2mm 38 columns Paper width 69 5mm Soft SW Setting Mode When Line Columns 40 33 are selected 360 dots lt Right offset 40 dots When setting Paper
36. ntering location and remains in stand by On models equipped with a rewinder if the cover is opened with paper set the paper is fed forward about 1 inch then returns to the centering position Closing After print operation and cut operation have been initialized it performs paper feed check and if there is printing data printing restarts N Caution If a cutter problem is caused by a paper jam etc the printer may stop with the cutter blade protruding so that the rear cover cannot be opened n this case press the FEED switch to eliminate the cutter problem without trying to force it open If the problem is not eliminated by pressing the switch insert a screw driver in the hole on the left side surface of the rear cover and rotate it to manually restore the cutter blade then open the cover The blade will be restored by turning it to either the left or the right 6 Be careful of the manual paper cut bar in particular to make sure that your fingers are not caught when opening and closing the cover 6 Opening the rear cover during printing causes malfunctions of the printer head or cutter unit Make sure that printing has stopped before you open the rear cover 6 To close the rear cover close it while holding the end of the paper so that the paper is not slack or bent inside the printer ee 5 3 49 ULIg ou Sunueds1q if Maintenance Mode Maintenance Mode The settings of the printer can be changed
37. ops at paper out During disabled status only BUSY is output and printing stops at paper out Paper Near End ENB ENB The PE signal enabled disabled is set at paper near end DIS when only the centro interface is set as enabled During enabled status PE FAULT are output and printing continues During disabled status nothing is output and printing continues Slashed Zero OFF OFF It sets whether or not slash is used with the numeral 0 ON zero Print Direct BI DIR BI DIR Designates printing direction When BI DIR is selected UNI DIR printing starts from the closer of the left and right ends of the next printing line from the print stop location During UNI DIR printing is usually done from the left end Auto LF OFF OFF The LF operation during CR code reception is selected ON When ON LF does not operate when OFF LF operates CR Carriage Return LF Line Feed Code Page 437 437 850 code page is selected 860 863 865 852 866 857 858 WPC ee gt 7 uepu uleyy Ete Maintenance Mode Soft SW Setting Mode Set item Initial value Setting value Remarks Buffer Size 4k 40byte The receiving buffer size is selected 4Kbyte nit Signal ENB ENB Selects enabled ENB disabled DIS of the printer DIS initialized signal PRIME during centro interface Selects enabled ENB disabled DIS of the 25pin reset signal during serial interface Buzzer ON ON Selects buzzer sound w
38. pact on printer operation even when the settings are changed Examples Items set for the Auto Cutter in models that are not equipped with an Auto Cutter Change of the setting of the Take Up Device in models to which rewinder specifications do not apply Concerning Auto Cutter operation The minimum cutting interval is 1 2 inch 3 lines with 6LPI Once a cut command has been executed even if a command is sent before the paper has fed at least 1 2 inch the cut command is ignored so the cut action cannot be executed Initial Factory Shipping Mode Setting the mode ale sive sie 727 Ve 1 Pressing the FEED switch twice in maintenance mode POWER LED is flashing causes the POWER LED PAPER OUT LED and the ERROR LED to begin to flash B twice 2 Reopening and closing the front cover in this status switches the POWER LED HOMER ag susan FEB PAPER OUT LED and the ERROR LED from flashing to continuously lit status 3 Pressing the FEED switch for 3 seconds or 55 more restores settings to the factory Reopening and closing the front cover shipping initialized status Flashing Lit PpOyV SDUEUSJUIEW mi Ete Maintenance Mode Cut Position Adjustment Mode Setting the mode 1 Pressing the FEED switch 3 times in maintenance mode POVVER LED is flashing causes the POVVER LED and A the ERROR LED to begin to flash Flashin
39. paratus set out in the Radio Interference Regulations of the Canadian Department of Communications This equipment is designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Use shielded cables to connect this device to computers Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment ETAT DE CONFORMITE EMI A L USAGE DES UTILISATEURS CANADIENS Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada Cet quipment produit et utilise l nergie a radiofrequences et s iln est pas install et utilis correctment c esst dire en accord strict avec les instructions du fabricant il risque de provoquer des int rferences avec la r ception de la radio et de lat l
40. pu ddy 156 271 1 EE 45 SENTE Appendixes Specifications Printer weight Standard model 2 20kg Auto cutter equipped model 2 3 0kg Auto cutter and rewinder equipped model 2 45kg But these exclude the AC adapter AC case ribbon and paper Environmental During operation Temperature 0 to 50 C conditions Humidity 10 to 90 RH no condensation During storage Temperature 20 to 70 C Humidity 5 to 90 RH no condensation 90 55 D E 50 2 v s 1 0 hu 1 l 0 35 50 Environmental temperature C Durability 7 5 million lines MCBF Head lifetime 150 million characters Cutter lifetime 1 million cuts Applicable standard CE Marking FCC Class A UL60950 Ribbon Cassette Cassette shape Single color specification color purple N 37701 color black NJ37703 Two color specification colors red black N 37702 Lifetime Single color specification color purple approx 4 million characters color black approx 3 million characters Two color specification colors red black red approx 750 000 characters black approx 1 5 million characters Be sure to use a recommended ribbon cassette in order to maintain printing quality and stabilize printer operation 46 m Paper Use the follovving printing paper in order to maintain printing quality and stabilize paper feeding Roll paper Paper width
41. riginal 2 copies When 3P printing speed falls 16 Paper widths 76 2 69 5 57 5 0 5 mm Roll diameter 630mm to b83mm Core diameter Interior diameter 6 1072 mm exterior diameter 627mm or less Paper thickness 1P 0 06 to 0 085mm Copy paper 0 05 to 0 20mm total thickness But the total thickness that can be cut is from 0 05 to 0 14mm No glue on the core or end of the paper Ribbon Method special ribbon cassette Colors Single color purple black 2 color black and red Life Purple approx 4 million characters continuous printing at 25 C Black approx 3 million characters continuous printing at 25 C Red black black 1 5 million characters Red 750 000 characters Interface Standard model 2 models either RS232C or IEEE1284 Emulation ESC POS Page mode CBM mode STAR mode Data buffer Receiving buffer 40 or 4K bytes NV bit image 128K bytes User NV memory 8K Merits Clamshell type Auto cutter function full cut partial cut Rewinder function Black mark sheet compatible Copy 2P 3P paper compatible DKD Drawer Kick Driver function ASB Auto Status Back function Power 5500 type Input DC24V 1 0A 55005 type Input AC100V 240V 0 55A 0 35A 50 60 Hz Power consumption 24W External dimensions Standard model 156 W x 247 7 D x 132 H mm 156 247 7 s xi
42. sible so that one of the sides of the paper does not slacken 1P roll paper Maintaining tension in the roll paper firmly close the rear cover until you hear a click Paper feeds automatically and stops at the print start position A Caution Be very careful not to let the rear cover catch your hands when closing the rear cover Roll paper that is gently pulled taut 5 Tear off surplus paper by holding one side of the end of the roll paper and pulling it towards you N Caution Do not insert any foreign objects such as a paper clip into the cutter unit 24 Suuedo1q elil kili Preparing the Printer nstalling Roll Paper Auto Cutter and Rewinder Equipped Model nstallation Method 1 Pull the rear cover open lever tovvards you to open the rear cover Rear cover open lever 2 thai pull the platen open lever towards you to open the platen unit 250 the attached partition in place if the copy roll paper you are using is 69 5mm vide or 57 5mm vide Change the paper width by changing the value set as the width using the Soft SW Setting Mode See page 35 N Caution When setting the roll paper be careful not to cut your vv hand on the edge of the paper 30 Location set for width of 57 5mm Location set for width of 69 5mm
43. uation does not improve replace it with a new ribbon cassette The paper is not cut ee 4 5 Check to make sure that the rear cover and front cover are closed If one of the covers is open close it If the paper still cannot be cut after you have closed the cover notify the dealer where you purchased the printer or service personnel ucu uleyy 1 1 0 Appendixes Specifications Printing mode Serial impact dot matrix Printing direction Bi directional Head pins 9 pins 6 0 3mm Pin interval 1 72inch Printing line number Paper width of 76 2mm 40 42 or 33 35 lines Paper width of 69 5mm 36 30 or 38 31 lines Paper width of 57 5mm 30 25 or 31 26 lines 200 400 dots full dot including half dot Font configuration 7x9 or 9x9 dots Character types ASCII 96 characters International characters Katakana Code pages 437 850 860 863 865 852 866 857 858 WPC1252 Panel switches 1 switch FEED 3 LED POWER PAPER OUT ERROR 1 buzzer Printing speed Printing 240CPS 3P paper 200CPS Through put 76 2mm wide 40 columns 7x9 3sp 6LPI 5 0LPS 69 5mm vide 36 columns 7x9 3sp 6LPI 5 4LPS 57 5mm wide 30 columns 7x9 3sp 6LPI 6 0LPS Paper feed Friction feed Minimum pitch 1 144 inch Paper feed speed 401 5 6LPI Paper Types 1P roll paper 2P copy roll paper 1 original 1 copy 3P copy roll paper 1 o
44. uation which if not observed and handled properly could result in death or serious injury Indicates a situation which if not observed and handled properly could result in injury Meaning of symbols N This symbol indicates that something must be handled carefully S This symbol indicates something that must not be done This symbol indicates something that must be done Never perform the following If not avoided these may cause damage or trouble to the printer or cause the printer to overheat and release smoke and cause burns or an electrical shock If the printer is damaged or is malfunctioning be sure to turn the printer off immediately and remove the power cord from the outlet then consult our service personnel e Do not jolt or impact the printer by stepping on dropping or hitting the printer Do not place the printer in a poorly ventilated area or shut off the air vent of the printer Do not place the printer where chemical reactions occur such as in laboratories or where air is mixed with salt or gas Do not use a power voltage or frequency other than those specified Do not plug unplug the power cord or attach detach the interface cable by simply grabbing the power cord or interface cable Do not pull or carry the printer when the tension of the power cord or interface cable is increased Do not drop or put foreign matter such as clips and pins into the printer This may cause problems Do not plug th
Download Pdf Manuals
Related Search