Cisco Systems WIC-1AM-V2 User's Manual
Contents
1. Configuration Examples for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC This section contains the following examples e Configuring for Asynchronous Dial Backup Example Configuring for Asynchronous Dial Backup Example In this example the interface S2 0 is configured as a primary link Configuring the route through the backup interface the V 90 modem WIC in this case is very important 10 0 0 0 in the IP route indicates the network number of the remote end Thus all packets for the destination IP are routed through the backup link if the primary link goes down The 180 in the route command indicates the cost of the route taken It should be more than the cost of the primary route This avoids the packets taking the backup link when the primary link is up The following example shows an asynchronous dial backup configuration interface Serial2 0 ip address 70 1 1 2 255 255 255 0 backup delay 15 15 backup interface as33 interface Async33 ip address 51 1 1 2 255 255 255 0 encapsulation ppp dialer in band dialer map ip 51 1 1 1 name m1_2621_33 modem script cisco default 101 dialer group 1 ppp authentication chap async mode interactive I router eigrp 100 redistribute static network 10 0 0 0 network 70 0 0 0 ip route 10 0 0 0 255 0 0 0 51 1 1 2 180 very important line 33 autoselect ppp modem InOut flowcontrol hardware transport input all For more information on configuring dial backup see the section Conf2. 192 168 100 26 mj F48A 1824M 4M Rev 2 bundle image bin If a modem has a call up the call will be torn down the modems selected in the upgrade command are hardware reset before starting the download A series of dots are printed one per second until the selected modems have been upgraded The router must not be powered cycled during the upgrade command The following example shows output of the upgrade modem firmware all command with a 1 port WIC 1AM V2 in 0 1 slot wic slot and a 2 port WIC 2AM V2 in 1 0 slot wic slot Router Sem firmware all file flash mj F48A 1824M 4M Rev 2 bundle image bin Verifying the modem firmware bundle Passed Decompressing modem firmware image Done Loading mj F48A 1824M 4M Rev 2 bundle image bin from 192 188 100 26 via FastEthernet0 0 F F P lrrrrr rrr rrr rrrrrrrrrrrrr rrr rrrrrrrrrrrrrrdbbbrbrery OK 282816 bytes Verifying the modem firmware bundle Passed Decompressing modem firmware image Done TTY1 Upgrading modem firmware TTY33 Upgrading modem firmware TTY34 Upgrading modem firmware Downloading modem firmware Please Wait TTY1 WIC AM Modem firmware download finished TTY34 WIC AM Modem firmware download finished TTY33 WIC AM Modem firmware download finished Finished upgrading modem firmware Command Description clear modem Resets the hardware for a manageable modem Cisco 10S Release 12 3 14 T e322 2 l Cisco WIC 1AM V2 and WIC 2A
3. can be combined using Multilink PPP MLP to increase connection speeds in a scalar manner Each connection is capable of V 90 speeds up to 56 kbps when connecting to a digital V 90 server modem For more information on MLP see Multilink PPP for DDR Basic Configuration and Verification Cisco 10S Release 12 3 14 T E Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card Information About Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Low Density Analog RAS Access In this application the V 90 modem WIC enables the platform to provide the services of a typical small remote access server RAS One service allows remote users to dial in and gain access to resources on the LAN or even across the WAN The analog modems in the modem WIC allow dial in connection speeds of up to 33 6 kbps but MLP can bind multiple links together and increase the throughput Another service allows PCs running Cisco DialOut Utility on the LAN to use the modems for dial out Users can connect to other modems bulletin boards AOL ISPs and so on or fax machines The modem WIC allows dial out connection speeds of up to 56 kbps when dialing a digital V 90 server modem or up to 33 6 kbps when dialing another analog modem Fax calls connect at up to 14 4 kbps Typical RAS deployments with the V 90 modem WIC use the 2 port modem version With enough slots the V 90 modem WIC can be used to scale to up to 24 modems There is no limit for
4. config line transport input all Step7 Router exit Exits the line configuration mode Example Router config line exit Step8 exit Exits global configuration mode Example Router config exit Step9 exit Exits privileged EXEC mode Example Router exit Upgrading the Modem Firmware Complete these steps to upgrade the firmware in the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC SUMMARY STEPS 1 enable 2 upgrade modem firmware all slot slot wic nm slot wic slot file source 3 exit Cisco 10S Release 12 3 14 T i Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card HZ How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC DETAILED STEPS Command or Action Purpose Step1 enable Enables privileged EXEC mode e Enter your password if prompted Example Router gt enable Step2 upgrade modem firmware all slot slot wic Enters information needed for the modem firmware nm slot wic slot file source upgrade e all Select all the modems in the router that are Example supported by the modem firmware file Router upgrade modem firmware all e slot Specify the router slot that is supported by the modem firmware file e slot Number of the slot selected e wic Specify a WIC supported by the modem firmware file e nm slot Number of the slot where the network module is located e wic slot Number of the slot where the WI
5. lines in the MLP bundle with WICs and population of WICs on any Cisco 2600 series or Cisco 3600 series multiservices platforms Cisco 10S Release 12 3 14 T O4 Al l Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC To configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC complete the following tasks e Configuring the Asynchronous Interface page 5 e Configuring the Country Code page 7 e Upgrading the Modem Firmware page 11 e Verifying the Modem Firmware Upgrade page 13 Configuring the Asynchronous Interface Complete the following steps to configure the asynchronous interface on the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC SUMMARY STEPS 1 enable 2 configure terminal 3 interface async number 4 ip unnumbered type number 5 encapsulation ppp 6 dialer in band no parity odd parity 7 dialer string number 8 dialer group group number 9 async mode interactive 10 peer default ip address pool poolname DETAILED STEPS CommandorAction Purposse sSSSS Step1 enable Enables privileged EXEC mode e Enter your password if prompted Example Router gt enable Step2 configure terminal Enters global configuration mode Example Router configure terminal Cisco 10S Release 12 3 14 T a Cisco WIC 1AM V2 and WI
6. pool used for defining the range of IP addresses for remote clients Configuring the Country Code Complete the following commands to configure the country code on the modem WIC SUMMARY STEPS enable configure terminal modemcap entry init string MSC GCl country code configuration values line Jine number ending line number modem autoconfigure type init string clear modem slot port exit exit o o N oF fF FSF YS DN exit Cisco 10S Release 12 3 14 T EE Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card HI How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC DETAILED STEPS Command or Action Purpose Step1 enable Example Router gt enable Enables privileged EXEC mode e Enter your password if prompted Step2 configure terminal Example Router configure terminal Enters global configuration mode Step3 modemcap entry init string MSC GCI country code configuration values Example Router config modemcap entry CC TBR21 FD amp F V1 AA S0 1 MSC V0 amp S0 1 GCI A6 Change the country code in the modemcap Use this chat script to initiate a country code e country code Use the codes in the Country Code Table The example shown here A6 is for Switzerland e configuration values Enter values for configuring the operating characteristics of the modem For more information about these parameters see AT Command Set and
7. C 2AM V2 Analog Modem WAN Interface Card HZ How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Command or Action Purpose interface async number Example Router config interface async 2 Enters the interface configuration mode for the asynchronous serial interface Enter the number of the interface you want to configure ip unnumbered type number Example Router config if ip unnumbered ethernet 0 Conserves IP addresses by configuring the asynchronous interface as unnumbered and assigns the IP address of the interface type that you want to leverage encapsulation ppp Example Router config if encapsulation ppp Sets the encapsulation protocol for Point to Point Protocol PPP dialer in band no parity odd parity Example Router config if dialer in band no parity Specifies that dial on demand routing DDR is to be supported This command specifies that chat scripts will be used on asynchronous interfaces The parity keywords do not apply to asynchronous interfaces dialer string number Example Router config if dialer string 5551212 Enters the dialer string telephone number dialer group group number Example Router config if dialer group 1 Controls access by configuring the interface to belong to a specific dialing group The number to which the
8. C is located e file Obtains the firmware information from the file named as source e source Name of the file with the firmware upgrade Step3 exit Exits privileged EXEC mode Example Router exit Examples This example shows the output of the upgrade modem firmware all command with a 1 port Cisco WIC 1AM V2 modem in 0 1 slot wic slot and a 2 port Cisco WIC 2AM V2 modem in 1 0 slot wic slot Example Loading mj F48A 1824M 4M Rev 2 bundle image bin from 192 188 100 26 via FastEthernet0 0 PErrr rrr rr br rr rr bere bp Pe PPP EEE et OK 282816 bytes Verifying the modem firmware bundle Passed Decompressing modem firmware image Done TTY1 Upgrading modem firmware TTY33 Upgrading modem firmware TTY34 Upgrading modem firmware Downloading modem firmware Please Wait Cisco 10S Release 12 3 14 T erazi l Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W TTY1 WIC AM Modem firmware download finished TTY34 WIC AM Modem firmware download finished TTY33 WIC AM Modem firmware download finished Finished upgrading modem firmware Verifying the Modem Firmware Upgrade Use these steps to verify that the firmware was upgraded in theCisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC SUMMARY STEPS 1 enable 2 show modem 3 exit DETAILED STEPS Command or Action Pur
9. Contents Cisco SYSTEMS Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card The Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card WIC for Cisco 2600XM Cisco 2691 Cisco 3700 and Cisco 3800 series multiservice platforms provide low density integrated modems for remote management dial backup and low density remote access servers RAS Feature History for the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card Release Modification 12 2 2 XB This feature was introduced 12 2 8 T This feature was integrated into the Cisco IOS Release 12 2 8 T 12 3 14 T This feature was integrated into the Cisco IOS Release 12 3 14 T to support the WIC 1AM V2 and WIC 2AM V2 WICs Finding Support Information for Platforms and Cisco 10S and Catalyst OS Software Images Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support To access Cisco Feature Navigator go to http www cisco com go cfn An account on Cisco com is not required e Prerequisites for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC page 2 e Restrictions for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC page 2 e Information About Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC page 3 e How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC page 5 e Configuration Examples for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC page 18 e Additi
10. M V2 Analog Modem WAN Interface Card Glossary W Glossary baud bits per second data rate of an asynchronous interface The term is not used as baud rate as that is redundant DDR dial on demand routing Also known as direct data routing or dial up routing PPP or IP DRAMM Dynamic Random Access Memory Module DSO A single 64 kbps channel of a T1 span DSP digital signal processor DSPM digital signal processing module voice module card 1OS Internet Operating System ISDN Integrated Services Digital Network NM network module MAR modular access router MLP Miultilink PPP OIR Online insertion and removal hot swap POTS Plain old telephone service PPP Point to Point Protocol PSTN Public Switched Telephone Network RAS remote access server TDM time division multiplexing Also used to describe a single channel on a TDM bus VFC voice feature card VIC voice interface card WIC WAN interface card This document is to be used in conjunction with the Release Notes for Cisco IOS Release 12 3T CCSP CCVP the Cisco Square Bridge logo Follow Me Browsing and StackWise are trademarks of Cisco Systems Inc Changing the Way We Work Live Play and Learn and iQuick Study are service marks of Cisco Systems Inc and Access Registrar Aironet BPX Catalyst CCDA CCDP CCIE CCIP CCNA CCNP Cisco the Cisco Certified Internetwork Expert logo Cisco IOS Cisco Press Ci
11. Register Summary for NM 8AM V2 NM 16AM V2 WIC 1AM and WIC 2AM Analog Modem WAN Interface Cards Note The semicolon is very important The GCI is an extended command that must come last in an AT string or must be followed by a semicolon Note To see the values configured for a modem use the show modemcap name command Step 4 line line number ending line number Example Router config line 1 1 Identify a specific line for configuration and enter line configuration collection mode e line number Relative number of the terminal line or the first line in a contiguous group that you want to configure when the line type is specified Numbering begins with zero e ending line number Optional Relative number of the last line in a contiguous group that you want to configure If you omit any keyword then line number and ending line number are absolute rather than relative line numbers Step 5 modem autoconfigure type init string Example Router config line modem autoconfigure type CC TBR21 Send the new modemcap string to the modem Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W Command or Action Purpose Step6 clear modem slot port Reset the hardware of the modem WIC e slot port Slot and modem port number Include the Example slash
12. TTY1 DSR was dropped Feb 10 20 38 36 ttyl Modem R Feb 10 20 38 37 Modem 0 0 Feb 10 20 38 37 TTY1 Feb 10 20 38 37 TTY1 Feb 10 20 38 37 ttyl Modem Feb 10 20 38 37 TTY1 cleanup Feb 10 20 38 38 TTY1 cleanup Feb 10 20 38 39 LINK 5 CHANGED Feb 10 20 38 39 TTY1 Feb 10 20 38 40 down Feb 10 20 38 40 TTY1 Feb 10 20 38 41 TTY1 Feb 10 20 38 42 Modem 0 0 WIC AM timer type 0 to destroy Feb 10 20 38 42 TTY1 no timer type Feb 10 20 38 42 TTY1 no timer type Feb 10 20 38 42 TTY1 no timer type Feb 10 20 38 42 TTY1 no timer type Feb 10 20 38 42 TTY1 no timer type Feb 10 20 38 42 Asyncl Feb 10 20 38 42 TTY1 restoring DTR Feb 10 20 38 42 TTY1 Feb 10 20 38 43 TTY1 Feb 10 20 38 43 TTY1 Modem ATZ gt OK Feb 10 20 38 44 TTY1 Feb 10 20 38 44 LINK 3 UPDOWN Feb 10 20 38 44 Feb 10 20 38 44 TTY1 Feb 10 20 38 44 TTY1 Modem command Feb 10 20 38 46 TTY1 Feb 10 20 38 46 TTY1 Feb 10 20 38 46 TTY1 Feb 10 20 38 54 As1 DDR re enable timeout changed state to reset R on Interface Asyncl changed state to R R switching to character modeFeb 10 20 38 42 TTY1 no allowing modem_process to continue hangup changed state to down Modem Registers IMR 0x0 LED 0x0 RstCntrl 0x0 MSR 0xFF Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card W Configuration Examples for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC
13. ample slash mark when entering this variable for example Router clear modem 0 0 1 1 Step5 exit Exits privileged EXEC mode Example Router exit Complete these steps to debug call disconnect on the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card Examples How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W The debug modem command shows the state of the TTY lines CTS UnAsserted Idle DCD UnAsserted EADY gt unknown CTS Asserted dropping DTR hanging up Async Int reset Dropping DT HANGUP gt unknown pending Delaying DT pending Delaying DT Interface Asyncl cleanup pending Delaying DT SLINEPROTO 5 UPDOWN Line protocol cleanup pending Delaying DT cleanup pending Delaying DT 1 to destroy 3 to destroy 4 to destroy 10 to destroy 2 to destroy Modem get info started Modem ATS86 gt 0210K Modem AT amp F V1SO0O 1 gt OK Interface Asyncl autoconfigure probe started AT amp F V1 GCI B5 SO 1 Modem configuration succeeded Detected modem speed 115200 Done with modem configuration Example This command will disconnect any active calls Clear reset modem 0 0 confirm resetting slot 0 port 0 line 1 Router Feb 10 20 38 34 Modem 0 0 Modem 0 0 WIC AM in modem state Feb 10 20 38 36 Modem 0 0 Feb 10 20 38 36
14. at the following URL http www cisco com go mibs RFCs RFCs Title No new or modified RFCs are supported by this feature and support for existing RFCs has not been modified by this feature Technical Assistance Link Description The Cisco Support website provides extensive online resources including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies To receive security and technical information about your products you can subscribe to various services such as the Product Alert Tool accessed from Field Notices the Cisco Technical Services Newsletter and Really Simple Syndication RSS Feeds Access to most tools on the Cisco Support website requires a Cisco com user ID and password http www cisco com techsupport Command Reference This section documents new and modified commands All other commands used with this feature are documented in the Cisco IOS Release 12 3 command reference publications New Commands e upgrade modem firmware page 21 Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card upgrade modem firmware upgrade modem firmware Syntax Description Defaults Command Modes Command History Usage Guidelines To upgrade the modem firmware use the upgrade modem firmware command in global configuration mode upgrade modem firmware all slo
15. ccess 0 0 WIC AM switching to PPP mode no timer type 1 to destroy no timer type 0 to destroy no timer type 2 to destroy 3 UPDOWN Interface Asyncl changed state to up Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card HZ How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Feb 10 20 34 20 Asl DDR Dialer statechange to up Feb 10 20 34 20 Asl DDR Dialer call has been placed Feb 10 20 34 20 Modem 0 0 PPP escape map Tx map FFFFFFFF Rx map 0 Feb 10 20 34 20 Modem 0 0 PPP escape map Tx map A0000 Rx map 0 Feb 10 20 34 21 Asl DDR dialer protocol up Feb 10 20 34 21 SLINEPROTO 5 UPDOWN Line protocol on Interface Asyncl changed state to up Debugging Call Disconnect Modem WIC SUMMARY STEPS 1 enable 2 debug modem 3 debug dialer 4 clear modem 5 exit DETAILED STEPS Command or Action Purpose Step1 enable Enables privileged EXEC mode e Enter your password if prompted Example Router gt enable Step2 debug modem Aids in troubleshooting the modem WIC e Use the no form of the command to stop the debugging Example process Router debug modem Step3 debug dialer events Aids in troubleshooting the modem WIC e Use the no form of the command to stop the debugging Example process Router debug dialer events Step4 clear modem slot port Reset the hardware of the modem WIC e slot port Slot and modem port number Include the Ex
16. d in the Cisco IOS Wide Area Networking Configuration Guide For troubleshooting and verification use only the following commands clear modem counters slot modem group group all debug modem show modem slot port Most of the show modem commands do not display the WIC 1 AM V2 and WIC 2AM V2 information You may also see error messages such as this example Router show modem operational status 0 0 Modem 0 0 doesn t exist Cisco 10S Release 12 3 14 T aa l Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card Information About Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Wi Information About Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC The Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card adds the following features to WAN interface card modems e Support for V 90 V 92 V 44 e A Cisco IOS command is provided to update the modem firmware This command allows for upgrading in the field e The country code is set by a modemcap e The modem uses the Conexant AT Command Set e More country codes are supported than on previous modems Three applications are available for the V 90 modem WIC on the Cisco 2600XM Cisco 2691 Cisco 3700 and Cisco 3800 series multiservice platforms e Remote Router Management and Out of Band Access e Asynchronous Dial on Demand Routing and Dial Backup e Low Density Analog RAS Access Remote Router Management and Out of Band Access In this mode
17. dialer access group belongs is defined with the dialer list command Acceptable values are within the range from 1 to 10 async mode interactive Example Router config if async mode interactive Configures interactive mode on the asynchronous interface peer default ip address pool poolname Example Router config if peer default ip address pool pool123 Assigns dial in clients IP addresses from an address pool To create an IP address pool use the ip local pool global configuration command exit Example Router config if exit Exits interface configuration collection mode Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W Command or Action Purpose Step12 exit Exits global configuration mode Example Router config exit Step13 exit Exits privileged EXEC mode Example Router exit Examples The following provides an example configuration Router config interface async 33 Router config if ip unnumbered 0 0 Router config if encapsulation ppp Router config if dialer in band dialer string 14085551234 Router config if dialer group 1 Router config if Router config if async mode interactive peer default ip address pool pool123 Router config if Note The entry pool123 is a name chosen for the
18. dress is not specified it will be Router ping 10 0 0 2 required in the ping system dialog Step5 exit Exits privileged EXEC mode Example Router exit Examples This command shows the state of the TTY lines Type escape sequence to abort Example Sending 5 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Success rate Feb 10 20 Feb 10 20 dte rx_speed 33600 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 Feb 10 20 100 byte ICMP 33 13353 333 133 4 33 23 35 133 333 1333 OOA 34 34 115200 modulation V34 protocol 234 3 34 234 234 234 234 53 53 533 53 Bay 53 534 535 534 537 is 18 18 18 18 18 18 18 2 20 Modem timeout is 2 seconds Echos to 10 0 0 2 Registers IMR 0x0 LED 0x0 RstCntrl 0x0 MSR 0xFF As1 DDR place call As1 DDR Dialing cause ip s 10 0 0 1 d 10 0 0 2 As1 DDR Attempting to dial 2 2772 CHAT1 Attempting async line dialer script Modem Registers IMR 0x0 LED 0x0 RstCntrl 0x0 MSR 0xFF CHAT1 Dialing using Modem script dial amp System script none CHAT1 process started CHAT1 Asserting DTR CHAT1 Chat script dial started 0 percent 0 5 Modem 0 0 DCD Asserted Modem 0 0 WIC AM in modem state Connect CHAT1 Modem TET TTY1 TTY1 SLINK LAPM compression_type V42B tx_speed 33600 Chat script dial finished status Su
19. er 4 modem inout 5 autoselect arap ppp slip during login 6 transport input all lat mop nasi none pad rlogin telnet v120 7 exit 8 exit 9 exit DETAILED STEPS Command or Action Purpose Step1 enable Enables privileged EXEC mode e Enter your password if prompted Example Router gt enable Step2 configure terminal Enters global configuration mode Example Router configure terminal Step3 line number Enters interface mode line configuration submode amp Note The number entered here must be the same as the number entered for the asynchronous serial interface when the interface configuration mode was first entered Example Router config line 1 Step4 modem inout Configures the line for both incoming and outgoing calls Example Router config if modem inout Step5 autoselect arap ppp slip during login Configures the line to automatically start an ARA PPP or SLIP session For this feature ppp is recommended Example Router config line autoselect ppp Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W Command or Action Purpose Step6 transport input all lat mop nasi none Defines which protocols can be used to connect to the line pad rlogin telnet v120 For this feature all is recommended Example Router
20. iguring Dial Backup for Serial Lines in theCis co IOS Dial Technologies Configuration Guide Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card Additional References W Additional References The following sections provide references related to the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Related Documents Related Topic Document Title Instructions for installing hardware WAN Interface Cards Hardware Installation Guide Instructions for connecting modems Modem Router Connection Guide Detailed information for commands and registers AT Command Set and Register Summary for V 90 WIC 1AM and WIC 2AM Analog Modem WAN Interface Cards Quick reference information for configuration Cisco IOS Dial Services Quick Configuration Guide Configuration information for serial lines Configuring Dial Backup for Serial Lines Standards Standards Title ITU T V 22 A B ITU T V 32 ITU T V 32 bis ITU T V 90 K56Flex V 22 bis V 34 1996 V 92 Quick Connect Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card Hs Command Reference MIBs MIBs MIBs Link e No new or modified MIBs are supported by this feature and support for existing MIBs has not been modified by this feature To locate and download MIBs for selected platforms Cisco IOS releases and feature sets use Cisco MIB Locator found
21. mark when entering this variable for example Router config line clear modem 0 0 1 1 Step7 exit Exits line configuration collection mode Example Router config line exit Step8 exit Exits global configuration mode Example Router config exit Step9 exit Exits privileged EXEC mode Example Router exit Country Code Table Use the codes in this table to set the country code Country Code Country Code Country Code Argentina 07 India 53 Romania 8E Australia 09 Ireland 57 Russia B8 Austria OA Israel 58 Singapore 9C Belgium OF Italy 59 Slovenia FC Brazil 16 Japan 00 South Africa 9F Bulgaria 1B Jordan SE Spain AO China 26 Korea 61 Sweden A5 Croatia FA Malaysia 6C Switzerland A6 Czech and Slovak 2E Mexico 73 Taiwan FE Federal Republic Denmark 31 Morocco 77 Thailand A9 Finland 3C Netherlands 7B TBR21 FD France 3D New Zealand TE Turkey AE Germany 42 Norway 82 United Arab B3 Emirates Greece 46 Poland 8A United Kingdom B4 Hong Kong 50 Portugal 8B United States B5 Hungary 51 Cisco 10S Release 12 3 14 T E Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card HZ How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Configuring the Line on the Analog Modem WIC Use these steps to configure the line on the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC SUMMARY STEPS 1 enable 2 configure terminal 3 line numb
22. onal References page 19 e Command Reference page 20 e Glossary page 23 Corporate Headquarters Cisco Systems Inc 170 West Tasman Drive San Jose CA 95134 1706 USA Copyright 2005 2006 Cisco Systems Inc All rights reserved Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card HZ Prerequisites for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC Prerequisites for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC The following Cisco multiservice platforms are supported for the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC e Cisco 2600XM e Cisco 2691 e Cisco 2800 e Cisco 3700 e Cisco 3800 Restrictions for Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC The Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC has the following memory requirements Platform Memory Requirements e Cisco 2600 ip 8M Flash 32M DRAMM A Caution Ensure that the RJ 11 CA11 telephone cable is disconnected from the modem WIC before installing or removing the modem WIC from the router The phone jack can have DC potential up to 56 5 VDC and can have ring signal up to 150 VAC in the United States A Caution Ensure that the router is powered OFF before installing or removing the modem WIC from the router The modem WICs do not support online insertion and removal hot swap Other than some currently unsupported commands the V 90 modem WIC supports all commands available for modem WICs as describe
23. pose Step1 enable Example Router gt enable Enables privileged EXEC mode e Enter your password if prompted Step 2 show modem slot port group number Display a high level performance report for all the modems or a single modem inside Cisco access servers Example e slot port Optional Location of a slot and modem Router show modem 0 0 inc firmware port The forward slash is required when you are entering this variable e group number Optional Assigns the group to which a specified modem belongs The group number range is from 1 to 200 Step3 exit Exits privileged EXEC mode Example Router exit Examples The show modem slot port group number command shows the state of the specified asynchronous interface Example Router show modem 0 0 inc firmware WIC AM firmware ACF3_V1 922F V90_4M_FSH Cisco 10S Release 12 3 14 T E Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card W How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC The show modem slot port group number command shows various performance statistics for a modem or group of modems Example Router show modem 0 3 0 Mdm Typ Status Tx RxX G Duration TX RX RTS CTS DSR DCD DTR 0 3 0 UnkKn Idle O 00 00 00 x x x x Modem 0 3 0 line 50 Async0 3 0 TTY50 WIC AM firmware ACF3_V1 922F V90_4M FSH Modem config Incoming and Outgoing Protocol UnKn Compression UnKn La
24. sco Systems Cisco Systems Capital the Cisco Systems logo Cisco Unity Enterprise Solver EtherChannel EtherFast EtherSwitch Fast Step FormShare GigaDrive GigaStack HomeLink Internet Quotient IOS IP TV iQ Expertise the iQ logo iQ Net Readiness Scorecard LightStream Linksys MeetingPlace MGX the Networkers logo Networking Academy Network Registrar Packet PIX Post Routing Pre Routing ProConnect RateMUX ScriptShare SlideCast SMARTnet The Fastest Way to Increase Your Internet Quotient and TransPath are registered trademarks of Cisco Systems Inc and or its affiliates in the United States and certain other countries All other trademarks mentioned in this document or Website are the property of their respective owners The use of the word partner does not imply a partnership relationship between Cisco and any other company 0601R Any Internet Protocol IP addresses used in this document are not intended to be actual addresses Any examples command display output and figures included in the document are shown for illustrative purposes only Any use of actual IP addresses in illustrative content is unintentional and coincidental Copyright 2004 2006 Cisco Systems Inc All rights reserved Cisco 10S Release 12 3 14 T EE Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card WE Glossary Cisco 10S Release 12 3 14 T 24 l
25. st clearing of Show modem counters never 0 incoming complete 0 incoming failures 0 outgoing complete 0 outgoing failure Troubleshooting the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC To troubleshoot the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC use the following commands starting in privilege EXEC configuration mode e Debugging Call Connect page 14 e Debugging Call Disconnect page 16 Debugging Call Connect Complete the following steps to debug call connect on the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC SUMMARY STEPS 1 enable 2 debug modem 3 debug dialer 4 ping system address 5 exit Cisco 10S Release 12 3 14 T 14s l Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card How to Configure the Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WIC W DETAILED STEPS Command or Action Purpose Step1 enable Enables privileged EXEC mode e Enter your password if prompted Example Router gt enable Step2 debug modem Aids in troubleshooting the modem WIC e Use the no form of the command to stop the debugging Example process Router debug modem Step3 debug dialer Aids in troubleshooting the modem WIC e Use the no form of the command to stop the debugging Example process Router debug dialer Step4 ping system address Diagnose basic network connectivity with the modem WIC e system address Address of the system to ping If a Example host name or system ad
26. t slot wic nm slot wic slot file source all Select all the modems in the router that are supported by the modem firmware file slot Select the modem in the specified router slot that are supported by the modem firmware file slot Number of the slot selected wic Select the modems in the specified router slot wic_slot that are supported by the modem firmware file nm slot Number of the slot where the network module is located wic slot Number of the slot where the WIC is located file Obtains the firmware information from the file named as source source Name of the file with the firmware No default behavior or values Global configuration mode Release Modification 12 313 This command was introduced The source for the modem firmware file can be any of the following cns Firmware filename flash Firmware filename ftp Firmware filename null Firmware filename nvram Firmware filename rcp Firmware filename system Firmware filename tftp Firmware filename xmodem Firmware filename ymodem Firmware filename Cisco 10S Release 12 3 14 T Cisco WIC 1AM V2 and WIC 2AM V2 Analog Modem WAN Interface Card W upgrade modem firmware Examples Related Commands It is best to copy the modem firmware file to Flash or Slot0 before trying to upgrade the modems After selecting the source specify the filename For example tftp
27. the modem WIC is used as a dial in modem for remote terminal access to the router s command line interface CLI for configuration troubleshooting and monitoring The modem WIC acts similar to a modem that is connected to the AUX port of a router but the integrated nature of the modem WIC greatly decreases configuration time and deployment and sustaining costs Typically the 1 port modem WIC is used for this application Connection speeds up to 33 6 kbps are possible Asynchronous Dial on Demand Routing and Dial Backup In this mode the V 90 modem WIC transports network traffic When ISDN service is not available and the traffic load does not justify a leased line or Frame Relay connection asynchronous dial on demand routing DDR is often the only choice for making a WAN connection Even at sites that do have leased line or Frame Relay connection asynchronous DDR can increase bandwidth during sustained traffic load In addition when the primary leased line or Frame Relay link is down during an outage asynchronous dial backup provides a secondary way to make the WAN connection Both the l port and 2 port versions of the V 90 modem WIC can be used for this application For more information on Asynchronous Dial on Demand Routing and Dial Backup see the section Configuring Dial Backup for Serial Lines in theCis co IOS Dial Technologies Configuration Guide Two ports on one modem WIC or even three or more ports spanning multiple modem WIC cards
Download Pdf Manuals
Related Search