Home

Chloraseptic APS-620 User's Manual

image

Contents

1. in all applications Failure to do so may result in personal injury or property damage Mount the switch in the hood locations away from water drain paths If necessary the included bracket may be used to move the switch away from rain gutters or allow mount ing to the firewall behind the hood seal In both cases the switch must be set up to allow the hood to depress the switch at least 1 4 inch when the hood is closed and fully extended when the hood is opened For direct mounting a 1 4 inch hole must be drilled Carefully check behind the chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines Drill a 1 4 hole in the desired location and thread the pin switch into it using a 7 16 nut driver or deep well socket If using the mounting bracket first secure the bracket to the desired location and secure the pin switch in the pre threaded mounting bracket hole DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VE HICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS Note Do not remove the fuse holders from this wire harness Fuses must be used and located as close as possible to the power source for adequate protection of the vehicle WIRING THE 6 PIN MAIN POWER HARNESS Connector C Pulse After
2. switch to the factory door unlock relay Negative Type Door Lock Circuits Factory Door Lock Uniock Switch To Red Lock Wire Of Control Module To Green Unlock Wire OF ontrol Module Vehicle From Fuse Box 12 Vo ts To Green Unlock Wire OF Control Module To Red Lock Wire Of Control Module To Factory Door Lock amp Unlock ControlRelays To Chassis Ground Vehicle Switch Positive Door Locks From Fuse Box 12 Volts To Green Unlock Wire OF Control Module To Red Lock Wire Of Control Module To Factory Door Lock amp Unlock ControlRelays To 12 Volts From Fused Source 128 7829A 5 of 12 5 Wire Polarity Reversal Door Locks From Fuse Box 12 Volts To Green Unlock Wire OF Control Module To Red Lock Wire Of Control Module X Vehicle To Factory Door Lock Switch amp Unlock ControlRelays Adding A Door Lock Actuator From Fuse Box 12 Volts To Green Unlock Wire OF Control Module To Red Lock Wire Of Control Module Wiring The 4 Pin Auxiliary Output Harness Connector A The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit s operation Understanding these outputs and the time in which they occur will allow you to determine if they are needed for the particular vehicle you are working on as well as how to use them Black w Blue Trace Wire Pulsed Ground Output Before
3. 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications not expressly approved by the party responsible for compliance voids the users authority to operate this device RevA 12 05 06 Add light flash reference during 1 28 7829A programming 1 f 12 0 INSTALLATION OF THE MAJOR COMPONENTS CONTROL MODULE Select a mounting location inside the passenger compartment up behind the dashboard The mounting location selected must be within 24 of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness Be certain that the chosen location will not interfere with proper operation of the vehicle Avoid mounting the module to or routing the wiring around the steering shaft column as the module or wiring may wrap around or block the steering wheel preventing proper control of the vehicle Secure the module in the chosen location using cable ties or screws as necessary Do Not Mount The Module In The Engine Compartment as it is not waterproof DASH MOUNTED LED The small LED included in the kit will serve as a visual indicator of the system s status and provide a visual deterrent to a potential thief The LED also provides important feed back information during the transmitter and feature program modes The LED should be installed in the dash in an area highly visible
4. IS CIRCUIT DOES NOT PERFORM AS SPECI FIED Green w Orange Trace Wire Tachometer Input Signal This wire will continually monitor the engine s tach rate while the unit is under power of the Remote Start module This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil This Remote Start unit learns the tach rate of the vehicle and in most cases will operate properly from one multi coil pack regardless of the number of cylinders If the vehicle has a single coil unit for each cylinder it may be necessary to connect this wire to more than one cylinder for proper tach reference See multi coil wiring detail below GREEN BLACK 1N4003 K K K MNN YELLOW IF THE FIRING ORDER IS 1 5 6 3 4 2 7 8 IF THE FIRING ORDER IS 1 8 4 3 6 5 7 2 1 5 6 ait glee Me 1 jal a 3 jel 5 T AS NG 7 QR U CONNECT TO CYLINDERS 1 3 7 OR 5 4 8 OR 6 2 1 CONNECT TO CYLINDERS 137 OR 862 OR 451 Dark Blue Wire Delayed 250mA Pulsed Channel 3 Output The Dark Blue wire supplies a 250mA ground pulsed output whenever channel three of the receiver is accessed Pressing the pre programmed transmitter button for three seconds will access channel two This is a low current output and must be connected to a relay to supply power to the trunk release or the circuit you wish to control Connect the Dark Blue wire to terminal 86 of a VF45F11 P amp B relay or
5. Low Bulb Test wire found in some GM vehicles This wire is also referred to as the ECM wake up wire in some Chrysler vehicles NOTE The outputs above are low current outputs and must be used with a relay if the circuit s requirement is more than 250 mA Ground 1 BLK Valet Enable 2 BLK WHT or GRAY Shut Down Hood Input 2 Gray Black Gnd While Running Output 6 Light Blue L Dome Light Output 7 Green White Black White Park LightIOutput__ White Park Light Input 15A Max 2White Red Ground Black 2 Pin Valet Program Override Push Button Switch Connector D The Black amp Grey twin lead wires loaded in the two pin blue connector are the ground supply and program valet override input of the Remote Start unit Route the two wires from the previously installed Push Button switch to the mating connector on the control module 128 7829A 7 of 12 3 Pin Antenna Receiver Connector F Route the 3 pin connector from the previously installed antenna receiver assemble to the mating connector on the control module This connector supplies 5 volts ground and RF rom the antenna receiver to the remote start module Be certain this connector is firmly seated making good contact to the control unit 2 Pin LED Harness Connector G Route the twin lead Red and Blue wires from the LED to the remote start control unit and plug the two pin connector into the mating white mini connector on the control modu
6. Model APS 620 Installation Manual This Remote Start System is designed to be used with Automatic Transmission Fuel Injection Vehicles Only COMPONENTS Control Module 2 Pin Door Lock Unlock Harness 2 Four Button RF Transmitters 3 Pin Parking Light Ground Harness Antenna Receiver 2 Pin LED Assembly 11 X 1 75 Foam Pad 2 Pin Push Button Valet Program Switch 6 Pin Main Power Harness 3 Pin Antenna Receiver Harness 7 Pin Accessory Harness 4 Pin Auxiliary Output Harness 1 Hood Pin Switch 4 Philips Head Black Drill Point Sheet 1 4 Female Spade Connector Metal Screw 8 X 1 2 Installation Owners Guide FEATURES Selectable Ignition Lock amp Unlock Selectable Door Lock Unlock Output Timing Safe Start Requires double push of the start button to engage the remote start function On Board Parking Light Relay Trunk Release Output Horn Chirp Output With Selectable Duration Selectable RF Start Chirp Car Finder Mode Can elect to have horn beep along with parking lights if connected Selectable Run Times 5 10 15 or 20 Minutes Selectable Gas or Diesel Automatic Start Timer Can be set to start your car automatically at 2 or 4 hour intervals 4 Negative Pulsed Aux Outputs Before Start After Start During Crank After Shut Down To aid installation in many vehicles with factory alarm systems FCC NOTICE This device complies with part 15 of the FCC rules Operation of this device is subject to the following conditions
7. Start The Black w Blue Trace wire will provide a 1 second 250 mA pulsed ground output 1 5 second before the remote start unit activates as well as when the transmitter is used to disarm the system Typical use for this output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when the remote start unit engages or when the transmitter is used to unlock the doors Page 6 128 7829A 6 of 12 Black w Light Green Trace Wire Pulsed Ground Output After Start The Black w Light Green Trace wire will provide a 1 second 250mA pulsed ground output after the vehicle is started under control of the remote start unit Typically this wire will be used to re lock the vehicle doors if the doors unlock automatically when the factory anti theft system is disarmed Black w Red Trace Wire Pulsed Ground Output After Shutdown The Black w Red Trace wire will provide a 1 second 250 mA pulsed ground output after the remote start unit shuts down This output will occur regardless of whether the circuit times out or is manually terminated Typically this output will be used to re lock the vehicle doors if the doors unlock automatically when the ignition circuit transitions to off Black w Yellow Trace Wire Ground Output During Start Crank The Black w Yellow Trace wire will provide a 250 mA ground output while the starter output of the remote start unit is active This output can be used to activate the Crank
8. Start 2 Black Green Pulse After Shut Down _ 3 Black Red Pulse During Cran 4 Black Yellow Lock 1 RED Unloc 2 GREEN Ignition 2 Output GREEN _ Battery Feed For Purple amp Blue 4 RED WHITE gnition 1 Output 6 BLUE a aA A Fused RED w WHITE TRACE WIRE 12 volt Battery 1 Source Locate the vehicle battery wire s at the ignition switch Verification These wires will register voltage in all positions of the ignition switch Connect the Red w White wire to the vehicle s battery wire This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays Fused RED WIRE 12 Volt Battery 2 Source Locate the vehicle battery wire s at the ignition switch Verification These wires will register voltage in all positions of the ignition switch Connect the Red wire to the vehicle s battery wire This wire provides power for the start relay and the accessory relay Page 3 128 7829A 3 of 12 YELLOW Wire Starter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear Understanding the difference between a me chanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installation method In addition you will realize why the connection of the safety wire is required for all mechanical switch con figurations Failure to make this connection properly can res
9. ce Wire Entry Illumination Ground Output This wire provides a 30 second ground output 300 mA Max whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered This wire should be connected to an external relay and wired to the vehicles interior entry lighting whenever the optional Interior Illumination circuit is desired Programming Tach Rate NOTE All applications require that tach be programmed The unit will not operate unless tach is programmed If an attempt is made to start the vehicle via the remote start without first programming tach the unit will flash the parking lights 7 times indicating tach has not been learned and stored If the tach rate is not properly programmed to the specific vehicle the unit may not realize that the vehicle is running in certain instances reengage the starter motor The Remote Start Unit will learn the tach rate of most vehicle s single coil multiple coil packs or single injector To learn tach 1 Turn the ignition key to the On position 2 Press and release the valet program push button switch 3 times 3 Immediately turn the ignition key Off 4 Press and hold the valet program push button switch then start the vehicle using the key 5 When the unit senses the tach signal the parking lights will begin to flash 6 Release the valet program pushbutton switch The parking lights will turn on for three second
10. equivalent Connect terminal 85 of the relay to a fused 12 volt source Connect the common normally open and normally closed contacts of the relay to perform the selected function of channel 3 Black w White Trace Wire 250 mA Horn Output The black w white trace wire is provided to beep the vehicle s horn This is a transistor ized low current output and should only be connected to the low current ground output from the vehicle s horn switch If the vehicle uses a 12 VDC horn switch then con nect the black w white trace wire to terminal 86 of the AS 9256 relay or an equivalent 30 Amp automotive relay and connect relay terminal 85 to a fused 12 VDC battery source Connect relay terminal 87 to the vehicle s horn switch output and connect relay terminal 30 to a fused 12 VDC battery source Light Blue Wire Ground Output While Running Under Remote Start Control This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off In all of the applications described Setting Up The System Programming Features Bank 1 Transmitter Channels Page 9 128 7829A 9 of 12 below a relay will be required The Light Blue wire can be used to accommodate the following situations A Shock Sensor By Pass B Additional Ignition Output C GM VATS Key Override Green w White tra
11. ess the pushbutton to advance to the next selectable feature Bank 3 Feature 1 Chirp Flash 2 Chirp Flash 3Chirp Flash 4 Chirp Flash 5 Chirp Flash 6 Chirps Flash Default 1 RF Start Chirp Off On On 2 Run Time 5 Min 10 Min 15Min 10 Min 3 Park Lights On Steady Flash Steady 4 Input Check Voltage Tach Tach 5 Voltage Level gt 0 5V B4 Start lt 0 5V B4 Start gt 0 5 6 Ign 2 Select Off With Crank On With Crank Same As Accy On With Crank 7 Diagnostics Off On Off 8 Crank Time 0 8Sec 1 0 Sec 1 5 Sec 2 0 Sec 1 0 9 Gas Diesel Gas Diesel 10 Diesel 15 Diesel 20 Gas 10 Blk Blue Aux O P Single Pulse As D L Pulse Single 11 Time Start 2 Hours 4 Hours 4 Hours 128 7829A 11 of 12 COMPLETING THE INSTALLATION After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system 1 2 Mount the control module up and behind the dash securing it in place with cable ties or screws Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact with under the dash board or in the engine compartment areas CAUTION Particularly avoid the area around the steering shaft and column as wires can 3 wrap around these mechanisms and impair the safe operation of the vehicle Apply the Caution Labels supplied with this kit to a conspicuous area
12. essible to the operator of the vehicle It is not necessary to conceal the switch However concealment is recommended as it offers a higher level of security The switch can be mounted to the lower dash panel in the driver s area Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch and also that the drill will not penetrate any existing factory wiring or fluid lines Drill a 9 32 hole in the desired location and mount the switch by passing it through the panel from the underside Secure the switch using the nut star washer Route the switch s connector toward the control module NOTE During the program sequence there are times when this switch and the ignition switch will be used simultaneously We recommend that the pushbutton switch be mounted on the left side of the ignition switch to facilitate this operation HOOD PIN SWITCH The pin switch included in this package are intended for protecting the hood area of the vehicle In all cases the switch must be mounted to a grounded metal surface When the pin switch is activated hood trunk open it will supply a ground to the input wire activating the alarm In addition the hood switch is required for the safety shut down of Page 2 128 7829A 2 of 12 the remote start unit If the vehicle is being worked on this hood switch prevents the remote start activation even if the RF command to start is issued This switch must be installed
13. in the engine compart ment Make sure to clean the surface before affixing the label Check the vehicle s wipers lights horn etc to insure proper operation Replace all panels that were removed during installation and retest the system Explain all activated features and safety systems associated with Remote Start Unit installed to the customer Place the Remote Start Valet Control Switch Tag on their respective switches and point these out to the customer 2006 Audiovox Electronics Corporation Hauppauge NY 11788 128 7829A 128 7829A 12 of 12
14. ition then 1 Press and release the push button valet program switch 3 times Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully entered See Owners Manual for transmitter programming Turn the ignition switch off then on to access Bank 2 Keyless Alarm feature selections 1 Flash when the ignition transitions off followed by 2 chirps Light flashes when the key i turned on indicates that you are in feature selection of bank 2 Press the pushbutton switch 1 time to access the first selection as shown below Use the lock button of the transmit ter to change the feature selection or press the pushbutton to advance to the next select able feature Bank 2 Feature 1 Chirp Flash 2Chirp Flash 3Chirp Flash 4Chirp Flash 5Chirp Flash 6 Chirps Flash Default 1stDoor Lock UL 1S 1S 3 5 S 3 5S 1 S Dbl1S Dbli 1S Dbl 1 Dbl 1 1S L 350mS ul 1S 1S 2nd Accy Lock Auto Lock On Auto Lock Off Auto Lock Off 3rd Accy UL Auto UL On Auto UL Off Auto UL Off 4th Horn Chirp 10mS 16mS 30mS 16mS 5h Chp Del TX On Off Off When finished setting the keyless alarm selectable features turn the ignition off then on to advance to Bank 3 Remote Start Selectable Features 1 Flash when the key transitions off and 3 chirps light flashes when the key transitions on Press the pushbutton switch one time to access the first selection as shown below Use the lock button of the transmitter to change the feature selection or pr
15. l of the Remote Start In most vehicles in order to shift into gear the brake pedal must be depressed The brake input will in turn cause the remote start unit to shut off Grey w Black Trace Wire Negative Inhibit Input The Grey w Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever it is grounded Connect the Grey w Black trace wire to the hood pin switch previously installed This wire must be routed through a grommet in the firewall and connected to the hood pin switch If the pin switch is to be used with an alarm system connect this wire using a diode assembly DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE HOOD PIN SAFETY SHUT DOWN FEATURE IMPORTANT This connection is a safety wire and must be connected to a hood pin switch and tested as described Failure to do so may result in personal injury or property damage This wire may also be used if the vehicle brake light circuit switches ground to the brake lights An isolation diode must be used for ground switched brake light circuits and must be connected to the output of the brake switch Page 8 128 7829A 8 of 12 To test this circuit while the vehicle is running under control of the remote start unit open the vehicle s hood The remote start unit should shut down immediately If not check the wiring to the control module and the under hood pin switch DO NOT RELEASE THE VEHICLE TO THE CONSUMER IF TH
16. le hese wires control the anode and cathode of the dash mounted LED 3 Pin Parking Light Input Output amp Ground Harness Connector H Black Wire Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis Be certain to remove any paint or grease and secure this wire with a self tapping screw and ring terminal White w Red Trace Wire Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay If the vehicle you are working on has 12 volt switched parking lights connect this wire to a fused 12 volt source Max 15 Amps NOTE If the vehicle s parking lights are ground switched connect this wire to chassis ground White Wire Parking Light Flasher Output This wire is the normally open contact of the on board parking light flasher relay Connect this wire to the vehicle parking light feed wire 7 Pin Accessory Input Output Harness Connector E Brown w Black Trace Wire Positive Inhibit Input The Brown w Black Trace wire provides an instant shutdown for the Remote Start Control module whenever it gets 12 volts If the Brake lights switch in the vehicle switches 12 volts to the brake light circuit connect the Brown w Black trace wire to the output side of the brake switch This will allow the Remote Start to shut down if an attempt is made to operate the vehicle without the key while running under the contro
17. s to indicate that the learned tach signal is stored and the unit is out of the tach learn mode NOTE If the unit fails to learn tach rate due to an improper tachometer connection or a poor tach source the parking lights will not flash To correct this situation locate and connect the Green Orange wire to the proper tach signal and then repeat the tach learn routine Diagnostics Enter Bank 3 and turn on selectable feature 7 as described in the feature selection and setting section Exit the feature selection mode then press and hold the pushbutton valet program switch abd then turn the ignition switch to on position NOTE Diagnostic mode is atemporary mode Once you have accessed the diagnostic mode the unit will pause for two seconds then begin to flash the last stored shut down code This code will be displayed three times in succession then the unit will automati cally exit the diagnostic mode The parking lights will flash a number of times indicating the reason for the last remote start shutdown The light flash indications are as follows 1 Flash Run timer expired 2 Flashes Low or no tach signal RPM 3 Flashes Positive or Negative inhibit wire activation 5 Flashes RF shutdown Remote signal received or manual start trigger wire reactivated 6 Flashes High tach signal RPM 7 Flashes Tach signal has not been learned Page 10 128 7829A 10 of 12 Start with the system disarmed turn the ignition switch to the on pos
18. so that it may be seen from the driver s seat as well as from outside the vehicle Inspect behind the chosen location to insure that the drill will not penetrate any existing factory wiring or fluid lines Carefully drill a 1 4 hole in the desired location and pass the connector end of the LED through the hole and toward the control module Press the LED firmly into place until it is fully seated in the mounting hole THE RECEIVER ANTENNA ASSEMBLY The Superregenerative Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range Choose a location above the belt line dashboard of the vehicle for best reception Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception In these vehicles route the antenna toward a rear window location for best reception Secure the antenna with double stick tape provided After securing the antenna with tape we advise also securing a section of the antenna cable to a fixed support This will prevent the antenna from dropping down in case the double stick tape is exposed to extreme heat which may loosen it s gummed surface Route the connector toward the control module using caution not to pinch the cable as this will cause poor or no RF reception to the control module VALET PROGRAM MANUAL OVERRIDE SWITCH Select a mounting location that is easily acc
19. ult in personal injury and property damage In all installations it is the responsibility of the installing technician to test the remote start unit and ensure that the vehicle cannot start via RF control in any gear selection other than park or neutral In both mechanical and electrical neutral start switch configurations the connection of the Yellow wire will be made to the low current start solenoid wire of the ignition switch harness This wire will have 12 volts when the ignition switch is turned to the start crank position only This wire will have 0 volts in all other ignition switch positions BLUE Wire Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch This wire will show 12 volts when the ignition key is turned to the ON or RUN and the START or CRANK positions and will have 0 volts when the key is turned to the OFF and ACCESSORY positions GREEN Wire Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch This wire will show 12 volts when the ignition key is turned to the ON or RUN position and is some cases the START or CRANK position This wire will show O volts when the key is turned to the OFF and ACCESSORY positions NOTE See programming information Bank 3 Selection 6 concerning this wire to allow output during the START mode VIOLET Wire Accessory Output Connect this wire to the Accessory wire from the ignition switch This wire
20. will show 12 volts when the ignition switch is turned to the ACCESSORY or ON and RUN posi tions and will show 0 volts when the key is turned to the OFF and START or CRANK positions Wiring The 2 Pin Door Lock Unlock Harness Connector B The Red amp Green Door Lock Unlock output wires provide a pulsed ground output to control the vehicle door lock unlock circuits The output of these wires has a maximum switching capability of 250 mA Many vehicles today have factory door lock relays which can be connected directly to these outputs however always confirm that the factory relays in your particular vehicle do not exceed the rated 250mA output of the units door lock unlock circuit Plug the 2 pin connector of the door lock unlock harness into the mating connector shell of the control module Determine the door lock circuit of the vehicle you are working on and wire according to the diagrams shown 128 7829A 4 of 12 3 Wire Ground Switched Door Lock Circuits In this application the Red wire of the 2 pin harness provides a ground pulse during the arming sequence or pulsed ground lock output Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay The Green wire of the 2 pin harness provides a ground pulse during the disarming sequence or pulsed ground unlock output Connect the Green wire to the low current ground signal wire from the factory door unlock

Download Pdf Manuals

image

Related Search

Related Contents

Downloaded from www.vandenborre.be  フレ࣭ムラックOS 基本組立説明書 - Garage  Emerson Fisher Baumann 81000 Instruction Manual    User's manual - PLANET Technology Corporation.  Sony DHC-ZX50MD User's Manual  RUBY-9713VG2AR User`s Manual  Publisher`s version (pdf, 491 KiB) - Infoscience  NURAL 8 - Versión 18/03/2003  Sistema de pintura com pó Encore HD com quadro eléctrico da  

Copyright © All rights reserved.
Failed to retrieve file