Chicago Electric 66274 User's Manual
Contents
1. Grounded Tools Tools with Three Prong Plugs SKU 66274 3 Prong Plug and Outlet Tools marked with Grounding Re quired have a three wire cord and three prong grounding plug The plug must be connected to a properly grounded outlet If the tool should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user reducing the risk of elec tric shock See 3 Prong Plug and Outlet The grounding prong in the plug is connected through the green wire in side the cord to the grounding system in the tool The green wire in the cord must be the only wire connected to the tool s grounding system and must never be attached to an electrically live terminal See 3 Prong Plug and Outlet The tool must be plugged into an appropriate outlet properly installed and grounded in accordance with all codes and ordinances The plug and outlet should look like those in the 1 N For technical questions please call 1 800 444 3353 preceding illustration See 3 Prong Plug and Outlet Double Insulated Tools Tools with Two Prong Plugs Outlets for 2 Prong Plug Tools marked Double Insulated do not require grounding They have a special double insulation system which satisfies OSHA requirements and complies with the applicable stan dards of Underwriters Laboratories Inc the Canadian Standard Associa tion and the National Electrical2. Protect the extension cords from sharp objects excessive heat and damp or wet areas RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS 120 240 VOLT AMPERES at full load RI gg 12 1 16 0 14 12 10 _16 1 20 0 12 10 Based on limiting the line TABLE A voltage drop to five volts at 150 of the rated amperes m EA za SKU 66274 For technical questions please call 1 800 444 3353 Symbology Double Insulated Canadian Standards Association Underwriters Laboratories Inc Volts Alternating Current nn xoodmin No Load Revolutions per 0 Minute RPM Page 5 SPECIFICATIONS section at the beginning of this manual including all text under subheadings therein before set up or use of this product UNPACKING General Operating Instructions Position the LED work light near the When unpacking make sure that work Loosen Knob 3 and adjust the item is intact and undamaged If any Lamp Assembly 1 to direct the light parts are missing or broken please call beam Tighten the Knob 3 Harbor Freight Tools at the number shown on the cover of this manual as soon as 2 Plug the Light into a grounded GFCI possible equipped 110V electrical outlet 3 To prevent accidents disconnect INITIAL SET UP power supply after use Clean then INSTRUCTIONS store indoors out of children s reach SAFETY INFORMATION section at the beginning of this manual including all te
3. CHICAGO LED WORK LIGHT VELEI 66274 SET UP AND OPERATING INSTRUCTIONS Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2008 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Manual Revised 09b SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no num ber Keep this manual and the receipt in a safe and dry place for future reference IMPORTANT SAFETY INFORMATION ates heat sparks which may ignite the dust or fumes Electrical safety a The Light s plug must match the outlet Never modify the plug in any wa
4. Code See Outlets for 2 Prong Plug Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration See Outlets for 2 Prong Plug Extension Cords Grounded tools require a three wire extension cord Double Insulated tools can use either a two or three wire extension cord As the distance from the supply outlet increases you must use a heavier gauge extension cord Using exten sion cords with inadequately sized wire causes a serious drop in voltage resulting in loss of power and possible tool damage See Table A The smaller the gauge number of the wire the greater the capacity of the cord For example a 14 gauge cord Page 4 can carry a higher current than a 16 gauge cord See Table A 4 When using more than one exten sion cord to make up the total length make sure each cord contains at least the minimum wire size required See Table A 5 If you are using one extension cord for more than one tool add the name plate amperes and use the sum to determine the required minimum cord size See Table A 6 If you are using an extension cord outdoors make sure it is marked with the suffix W A W in Canada to indicate it is acceptable for outdoor use 7 Make sure the extension cord is properly wired and in good electrical condition Always replace a damaged extension cord or have it repaired by a qualified electrician before using it 8
5. ct or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note No replacement parts SKU 66274 For technical questions please call 1 800 444 3353 Page 8
6. ean external surfaces of the tool with clean moist cloth The individual LED lights are replace able but should only be done by a qualified service technician using the proper tools Awarnine If the supply cord of this power tool is damaged it must be replaced only by a qualified service technician ASSEMBLY DIAGRAM For technical questions please call 1 800 444 3353 Page 7 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or con sequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the produ
7. erating alone e Properly maintain and inspect to avoid electrical shock e Any power cord must be prop erly grounded Ground Fault Circuit Interrupter GFCI should also be implemented it prevents sustained electrical shock 5 WARNING Handling the cord on this product will expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling Califor SKU 66274 nia Health amp Safety Code 2524915 et seq The warnings precautions and instructions discussed in this instruc tion manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and cau tion are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS GROUNDING For technical questions please call 1 800 444 3353 Improperly AWARNING connecting the grounding wire can result in electric shock Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded Do not modify the power cord plug provided with the tool Never remove the grounding prong from the plug Do not use the tool if the power cord or plug is damaged If damaged have it repaired by a service facility before use If the plug will not fit the outlet have a proper outlet installed by a qualified electrician Page 3
8. is enables better control of the Work area safety a Keep work area clean and well lit Cluttered or dark areas invite accidents Light in unexpected situations Light use and care a Maintain the Light Check for Do not operate the Light in explo sive atmospheres such as in the presence of flammable liquids gases or dust The Light gener For technical questions please call 1 800 444 3353 breakage of parts and any other condition that may affect the Light s operation If damaged have it repaired before use Page 2 Many accidents are caused by poorly maintained items 5 Service a Have the Light serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the Light is maintained Light Safety Warnings 1 Maintain labels and nameplates on the Light These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement 2 Do not leave the Light unattended when it is plugged into an electrical outlet Turn off the Light and unplug it from its electrical outlet before leav ing 3 This product is not a toy Keep it out of reach of children 4 People with pacemakers should consult their physician s before use Electromagnetic fields in close prox imity to heart pacemaker could cause pacemaker interference or pacemaker failure In addition people with pace makers should e Avoid op
9. xt under subheadings therein before set up or use of this product TO PREVENT AWARNING SERIOUS INJURY FROM ACCIDENTAL OPERATION Turn the unplug the light from the electrical outlet before assembly 1 Read the ENTIRE IMPORTANT Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Assembly 1 Slide the Base 2 into the bottom of the Lamp Assembly 1 2 Secure with the Knob 3 OPERATING INSTRUCTIONS 1 Read the ENTIRE IMPORTANT SAFETY INFORMATION SKU 66274 For technical questions please call 1 800 444 3353 Page 6 USER MAINTENANCE INSTRUCTIONS PARTS LIST SKU 66274 Procedures not specifically A explained in this manual must be performed only by a qualified technician TO PREVENT AWARNING SERIOUS INJURY FROM ACCIDENTAL OPERATION Unplug the light from its electrical outlet before performing any inspection maintenance or cleaning procedures TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise occurs have the problem corrected before further use Cleaning Maintenance and Lubrication BEFORE EACH USE inspect the general condition of the tool Check for loose screws misalignment or binding of moving parts cracked or broken parts damaged electrical wir ing and any other condition that may affect its safe operation AFTER USE cl
10. y Do not use any adapter plugs with the Light Unmodi fied plugs and matching outlets will reduce risk of electric shock Avoid body contact with ground ed surfaces such as pipes radiators ranges and refrigera tors There is an increased risk of electric shock if your body is In this manual on the labeling and all other information grounded c Do not expose the Light to rain provided with this product This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death General Safety Rules WARNING Read all safety A warnings and instructions 1 SKU 66274 Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference or wet conditions Water entering the Light will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the Light Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock For indoor use only Do not use this product outside or in wet loca tions Personal safety a Use personal protective equip ment Wear ANSI approved eye protection during assembly Do not overreach Keep proper footing and balance at all times Th
Download Pdf Manuals
Related Search