CDA HCG500 User's Manual
Contents
1. HCG500 HCG520 gas hobs Manual for Installation Use and Maintenance C D A Customer Care Department The ICIDIA Group Ltd Harby Road e Langar Nottinghamshire e NG13 9HY T 01949 862 012 F 01949 862 003 E service cda eu W www cda eu Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorr product Please note that CDA reserve the right to invalidate the guarantee supplied with th installation or misuse of the appliance or use in a commercial environment This appliance is not designed to be used by people including children with reduced capacity or who lack experience or knowledge about it unless they have had supervision the appliance by someone who is responsible for their safety Under no circumstances should any external covers be removed for servicing or maintenan personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Cu fault with your appliance and to register your appliance for guarantee purposes CE Declarations of Conformity This appliance has been manufactured to the strictest standards and complies with all ap Gas safety Electrical safety LVD and Electromagnetic interference compatibility EMC contact with food conform to EEC 89 109 IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCOR 2002 96 EC At the end of its working life the product must be taken to a sp2. control and8 onthe diagram above The control panel Turning the contro below achieves the following Closed OFF position Maximum position Provides fast b Minimum position Provides simm The flame can be set to the the control knob through the clockwise direction Igniting the Burners To ignite the burners follow these instructions A Lightly press the control knob shown on the right and turn the knob anti clockwise to the maximum position Press and hold the control down to begin the ignition process a clicking sound will be heard N Once the burner is lit adjust the burner power to the required position To turn the burner off turn the knob clockwise past the maximum setting to the off position Some models are fitted with a flame failure device designated by F in model number If your hob is fitted with such a device hold down the control knob for a few seconds after ignition to allow the safety device to detect that the burner is lit Flame failure devices operate by shutting off the supply of gas to the burner in the event that the flame is extinguished accidentally Please note e The ignition device should not be operated for more than 15 seconds e Ifa burner does not ignite or turns off accidentally turn the control knob to the off position and wait for one minute before attempting to reignite the burner If the burner does not ignite repeat the ignition process with th
3. e burner at the minimum position Efficient use of your Hob The hob is equipped with burners of different sizes designed to accommodate most shapes and sizes of pan For best results only use pans with flat bottoms and choose an appropriate burner depending on the size of the pan The most efficient use of the hob is shown below where the pan and burner are correctly chosen Ensure that the pans do not overlap the edge of the pan stand or cover the control panel The table below shows the sizes of pan that should be used with each burner vlem avimi Dan D TIC CSE CII VIAATIUME Pari Burner Size Minimum Pan Diamete Care and Maintenance As the hob has a stainless steel or enamel surface you should use a nonabrasive cleaner A Cif will scratch the surface and could erase the control panel markings Stainless steel can be using a dilute solution of water and mild detergent and drying to a shine with a clean cloth Over time with use the stainless steel surface may discolour this is normal and does not c pliance Proprietary stainless steel cleaners are available We recommend the CDA E Cloth Team for cleaning stainless steel surfaces The enamelled parts of hobs are not suitable for cleaning in dishwashers these should be washe IMPORTANT e Steam cleaners must not be used when cleaning this appliance e Ensure that all parts are correctly replaced after cleaning before attempting to use the ho e After removin
4. e wire which is coloured green and yellow must be connected to the terminal marked E Earth or coloured green e The wire which is coloured blue must be connected to the terminal marked N Neutral or coloured black e The wire which is coloured brown must be connected to the terminal marked L Live or coloured red USE A 3 AMP FUSE Note Use a 3A Fuse Assembly and electrical connection should be carried out by specialised personnel When installing this product we recommend you seek the help of another individual Gas Supply Requirements IMPORTANT THIS APPLIANCE SHOULD BE FITTED BY A GAS SAFE REGISTERED FI QUALIFIED PERSON e This installation must comply with the Gas Safety installation and use Regulations 198 e This appliance is category IIZH3 and is designed for use in the UK and Ireland The insta Gas Safety installation and use Regulations 1984 e The CDA Group Ltd is not legally able to provide any assistance in the installation of gas a Safe registered installers Any Gas Safe registered fitter requiring help must provide their number Information supplied will be validated before help is provided e This appliance is suitable for conversion to Liquid Petroleum Gas G30 or G31 A kit is fit the conversion kit yourself e This appliance is adjusted for natural gas G20 at 20mbar only e In the event that this appliance is not installed in accordance with the above require disconnected from the mains gas su
5. ecial local authority waste c providing appliance recycling services Disposing of a household appliance separately avoids possible negative consequences for t also enables the constituent materials to be recovered saving both energy and resources dispose of household appliances separately the product is marked with a crossed out whe Please note e Gas hobs become hot and remain hot during and immediately after use Do not touch hob spill tray until the appliance has been allowed to cool e Keep children away from the appliance when in use e After use please ensure that the gas taps are in the Off position e Ensure that the appliance is correctly adjusted for the type of gas available before instal e The use of a gas appliance produces heat and humidity in the room in which it is install well ventilated either by the use of natural ventilation outlets e g windows or a duct e This hob Class 3 has been designed for use only as a cooking appliance Any other us be considered incorrect and therefore dangerous Using your hob Gas burners 3 0kW 2 Left Semi Rapid burner 1 75kW 3 Right Semi Rapid burner 1 75kW 4 1 0kW 1 Rapid burner Auxiliary burner Control panel 5 Right Semi Rapid burner control knob 6 Left Semi Rapid burner control knob 7 Rapid burner control knob 8 Auxiliary burner control knob This appliance is class 3 D gt gt ONOM Gas burners Gas flow to the burners is
6. g the pan stands ensure the rubber pads are in place on the base of the pa the pan stands straight and level on the hob What to do if you smell gas 1 Open doors and windows 2 Turn the gas supply off 3 Call Transco on 0800 111 999 Total rated gas input 7 5kW Mains electrical voltage 230 240Vac Total rated electrical consumption lt 1W If your Hob is not working 1 Check that the mains supply has not been switched off 2 Check that the fuse in the spur has not blown 3 Ensure that the burner components are not excessively soiled as this can lead to ignition Contact CDA Customer Care A Customer Care Department The CDA Group Ltd Harby Road Langar Nottinghamshire T 01949 862012 F 01949 862 003 E service cda eu W www cda eu Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PE WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A We recommend that the appliance is connected by a qualified electrician who is a member comply with the I E E and local regulations The wires in the mains lead of this appliance are coloured in accordance with the following Green amp Yellow Earth Blue Neutral Brown Live pa the colours of the mies mn the mains lead for i appliance my not correspond DOUBLE POLE SWITCHED with the coloured markings identifying the terminals connecting to the fuse spur FUSE SPUR OUTLET proceed as follows e Th
7. mus is recommended Fig 7 If the instructions supplied with the hood dictate that the hood greater than 700mm then that height is the minimum required Wall furniture requirements The minimum height of any cabinet immediately above the hob is 900mm The minimu including light pelmets is 400mm unless they are manufactured from a material resistan Notes e Do not position this appliance above a refrigeration unit The heat generated may cause the e This appliance is designed to be installed into cabinet units capable of withstanding temper above ambient temperature e If there is no oven to be built in below the hob an isolation shelf should be fitted to prote temperatures If the hob is to be installed above a working drawer then a partition shoul contents and user from the heat generated during use This should be fitted 100mm belo e Never place perishable foods in the cupboard below the appliance How to install the hob Overall dimensions of the hob Width 585mm Depth 500mm Worktop cut out dimensions Width 550mm Depth 470mm 1 Make the required hole in the worktop Before doing this you must check the instructi hood to ensure that you will have the required clearance The cut out Fig 4 shows a 6 cut out edge The distance from the hob when fitted to the back wall is 50mm If a splashback worktop upstand is to be fitted take this into account when cutting the hole hob should be positioned away from
8. orts e LPG identity plate w Remove the injectors and replace with the corresponding injector as shown in the table below Setting up minimum flow rates Remove the control knobs N Turn on the LP gas supply light the burners and turn the controls to the minimum position as indicated by the small flame U3 Insert a 2 5mm screwdriver into the hole at the top of the tap and turn the adjustment screw fully clockwise as shown in figure 6 A Turn the controls to maximum position then quickly to the minimum position make sure the flame does not extinguish Required e 7mm AF nut spinner vi Replace the knobs e Replacement injectors NG identity plate LPG to Natural Gas Conversion This hob can be converted from propane operation at a nominal inlet pressure of 37mb nominal inlet pressure of 28 30mbar to natural gas at 20mbar This conversion must only b person i e a Gas Safe registered fitter Ooo a S o S OO Fitting the Hob Unpacking the hob Take care not to lose or mishandle any parts Fitting position of the hob This appliance must be installed a minimum of 50mm from any back wall and a minimu adjacent vertical surfaces e g a tall cupboard end panel This may be reduced to 100mm if t to fire tiles or steel for example These dimensions are shown in Fig 6 If fitting a cooker hood above the hob If a cooker hood is to be installed above the hob the height of the hood above the hob
9. pply until any faults are rectified this is a legal requi e This appliance should be installed using 15mm copper pipe connected via a shut off valve in valve needs to be accessible in an emergency or for service purposes e This appliance must not be connected to a combustion gas recovery scavenging system e The connection to the gas supply must comply with all current regulations in force e Weare not legally able to offer advice on the installation of gas appliances to non Gas S Ventilation All rooms require a window or equivalent e g a door which can be opened Some rooms addition to a window see below This unit must not be used in a room which is less than 5m3 The following table details t kitchen volume L x W x H in m3 D ee No permanent vent required if a door opens to the outside The above requirements also allow use of a gas oven and grill but if there are any other f same room consult the relevant British Standard BS5440 or Gas Safe document Natural Gas to LPG Conversion This hob can be converted from natural gas to propane operation at a nominal inlet pr operation at a nominal inlet pressure of 28 30mbar This conversion must only be carriec i e a Gas Safe registered fitter Required Instructions to fit replacement injectors e 7mm AF nut spinner Disconnect the appliance from the gas and electrical supplies e Replacement injectors N Remove burner components and pan supp
10. the rear wall or splashback is 50mm 2 Position the hob seal as shown in Fig 6 ensuring that the ends meet without overlapping D 3 Secure the hob to the worktop using the fixing brackets and screws supplied as show sealant after tightening the brackets Do not over tighten the fixing brackets Notes CDA To contact our Customer Care Department or for Service please contact us on the details below
Download Pdf Manuals
Related Search